Front end INFINITI FX35 2004 Service Manual

ACC-2
PRECAUTIONS
Revision: 2004 November 2004 FX35/FX45
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
ABS00A37
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.

ACS-4
[ICC]
PRECAUTIONS
Revision: 2004 November 2004 FX35/FX45
[ICC]PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
AKS007IE
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for ICC System ServiceAKS006Y8

Do not look straight into the laser beam discharger when adjusting laser beam aiming.

Turn the ON/OFF switch OFF in conditions similar to driving, suchlike Free rollers or Chassis dynamome-
ter.

Do not use the ICC sensor removing from vehicle, disassemble, or remodel the sensor.

Erase DTC when replacing parts of ICC system, then check the operation of ICC system after adjusting
laser beam aiming if necessary.
Wiring Diagrams and Trouble Diagnosis AKS006Y9
When you read wiring diagrams, refer to the followings:

Refer to GI-15, "How to Read Wiring Diagrams" in GI section

Refer to PG-3, "POWER SUPPLY ROUTING CIRCUIT" for power distribution circuit in PG section
When you perform trouble diagnosis, refer to the followings:

Refer to GI-11, "HOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES" in GI section

Refer to GI-27, "How to Perform Efficient Diagnosis for an Electrical Incident" in GI section

DESCRIPTION
ACS-7
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2004 November 2004 FX35/FX45
Components DescriptionAKS006YD
CAN CommunicationAKS00815
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tric control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN COMMUNICATION UNIT
Refer to LAN-6, "CAN Communication Unit" .
Switch OperationAKS006YF
The system is operated by a master ON/OFF switch and four control switches, all mounted on the steering
wheel.
ComponentVe h i -
cle-to-
vehi-
cle dis-
tance
con-
trol
modeCon-
ven-
tional
(fixed
speed)
cruise
con-
trol
modeBrake
assist
(with
pre-
view
brake)Description
ICC unit×××Operates throttle control actuator and brake booster based on that sensor
signals and CAN communication data, then controls vehicle distance.
ICC sensor××Irradiate laser beam, and receives reflected laser beam to measure dis-
tance from preceding vehicle.
ECM××Transmits throttle position signal and ICC steering switch signal to ICC unit.
ABS actuator and electric
unit (control unit)×××Transmits wheel speed signal to ICC unit.
Brake pressure sensor××Detects fluid pressure in master cylinder.
Brake booster××Adjusts brake fluid pressure, based on command from ICC unit.
BCM×Transmit front wiper request signal to ICC unit.
TCM××Transmits gear position signal and output shaft revolution signal to ICC
unit.
SKIA5973E

LASER BEAM AIMING ADJUSTMENT
ACS-13
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2004 November 2004 FX35/FX45
2. Adjust the height of the target stand so that the point of the trian-
gle aims the center of the ICC sensor.
ADJUSTING THE RIGHT-LEFT POSITION OF THE TARGET
1. Attach a scale (at least 350 mm [14 in] or longer) or stick as
shown in the figure.
2. Suspend a thread with weight on the tip of the thread to 310 mm
(12.2 in) left side of the target board from the center of the tar-
get board on top.
SETTING THE TARGET
1. Suspend a thread with weight on tip to splice the center of the front and back bumpers. Then, mark the
center point on the ground as each weight points.
2. Link the front and back bumpers center points marked on the ground, and mark a point 5 m ahead of the
sensor, on the extended line of the previous link line of the bumper center points. Then, adjust the position
of the target board so that the weight come on the top of the marked point (5 m ahead of the sensor) and
face to the vehicle.
3. Adjust the position of the target board so that the extended line
that links the center of the rear window (the center of the rear
window defogger pattern) and the center of the front windshield
(the setting part of the room mirror) align with the weight sus-
pended from the board.
4. Remove the thread suspended to the left side of board and suspend a thread with weight on tip on the
center of the target board.Then mark the point of weight on the ground.
SKIA6180E
SKIA1211E
SKIA5975E
SKIA1213E

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
ACS-57
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2004 November 2004 FX35/FX45
4. CHECK TCM GEAR POSITION SIGNAL
With CONSULT-II

With TCM data monitor with CONSULT-II, check that gear positions are correct.
OK or NG
OK >> Replace ICC unit. Erase DTC and perform self-diagnosis of ICC system again.
NG >>

Perform TCM diagnosis.

After repair, erase DTC and perform self-diagnosis of ICC system again.
5. CHECK TCM TURBINE ROTATION
With CONSULT-II

With TCM diagnosis, check that turbine rpm is normal. Refer to AT- 1 4 3 , "DTC P1716 TURBINE REVOLU-
TION SENSOR" .
OK or NG
OK >> Replace ICC unit. Erase DTC and perform self-diagnosis of ICC system again.
NG >>

Perform TCM diagnosis.

After repair, erase DTC and perform self-diagnosis of ICC system again.
DTC 102 RADAR STAINAKS006ZI
1. VISUAL INSPECTION (1)

Check that there is no contamination and foreign material on ICC sensor body window.
OK or NG
OK >> GO TO 2.
NG >>

If any, remove them.

After that, erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC
system again.
2. VISUAL INSPECTION (2)

Check ICC sensor body window for cracks.
OK or NG
OK >> GO TO 3.
NG >>

Replace ICC sensor, and adjust laser beam.

After that, erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC
system again.
3. ASKING COMPLAINTS
1. Is there any trace of contamination or foreign material on ICC sensor?
2. Is there any possibility that vehicle was driven in snow or ICC sensor was frosted?
3. Is there any possibility that ICC sensor was fogged temporarily? (Front window glass may have also
tended to be fogged.)
Ye s o r N o
Yes >> Explain difference in displays between contamination detection result and current indication to
customer, and tell them “This is not malfunction”.
No >>

Replace ICC sensor, and adjust laser beam aiming.

After that, erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC
system again.

AT-4Revision: 2004 November 2004 FX35/FX45CONSULT-II Reference Value ..............................187
Diagnostic Procedure ...........................................187
TROUBLE DIAGNOSIS FOR SYMPTOMS ............188
Wiring Diagram — AT — NONDTC ......................188
A/T CHECK Indicator Lamp Does Not Come On . 191
Engine Cannot Be Started In “P” or “N” Position ..193
In “P” Position, Vehicle Moves When Pushed ......193
In “N” Position, Vehicle Moves ..............................194
Large Shock (“N” to “D” Position) .........................195
Vehicle Does Not Creep Backward In “R” Position .198
Vehicle Does Not Creep Forward In “D” Position . 201
Vehicle Cannot Be Started From D
1 .....................203
A/T Does Not Shift: D
1 → D2 ................................206
A/T Does Not Shift: D
2 → D3 ................................208
A/T Does Not Shift: D
3 → D4 ................................211
A/T Does Not Shift: D
4 → D5 ................................213
A/T Does Not Perform Lock-up ............................216
A/T Does Not Hold Lock-up Condition ..................218
Lock-up Is Not Released ......................................220
Engine Speed Does Not Return To Idle ................221
Cannot Be Changed to Manual Mode ..................222
A/T Does Not Shift: 5th gear → 4th gear ..............223
A/T Does Not Shift: 4th gear → 3rd gear ..............225
A/T Does Not Shift: 3rd gear → 2nd gear .............227
A/T Does Not Shift: 2nd gear → 1st gear .............229
Vehicle Does Not Decelerate By Engine Brake ....231
SHIFT CONTROL SYSTEM ....................................233
Control Device Removal and Installation ..............233
Adjustment of A/T Position ...................................234
Checking of A/T Position ......................................234
A/T SHIFT LOCK SYSTEM .....................................235
Description ............................................................235
Shift Lock System Electrical Parts Location .........235
Wiring Diagram — AT — SHIFT ...........................236
Diagnostic Procedure ...........................................237
KEY INTERLOCK CABLE ......................................239
Components .........................................................239
Removal and Installation ......................................240
ON-VEHICLE SERVICE ..........................................242
Control Valve with TCM and A/T Fluid Temperature
Sensor 2 ...............................................................242
Parking Components (2WD Models Only) ............253Rear Oil Seal .........................................................259
Revolution Sensor Components (2WD Models
Only) .....................................................................260
AIR BREATHER HOSE ...........................................264
Removal and Installation .......................................264
TRANSMISSION ASSEMBLY .................................266
Removal and Installation (2WD Models) ...............266
Removal and Installation (AWD models) ..............269
OVERHAUL .............................................................274
Components ..........................................................274
Oil Channel ...........................................................282
Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings ..........................284
DISASSEMBLY .......................................................286
Disassembly ..........................................................286
REPAIR FOR COMPONENT PARTS ......................303
Oil Pump ...............................................................303
Front Sun Gear, 3rd One-Way Clutch ...................306
Front Carrier, Input Clutch, Rear Internal Gear .....308
Mid Sun Gear, Rear Sun Gear, High and Low
Reverse Clutch Hub ..............................................314
High and Low Reverse Clutch ..............................320
Direct Clutch .........................................................323
ASSEMBLY .............................................................325
Assembly (1) .........................................................325
Adjustment ............................................................338
Assembly (2) .........................................................341
SERVICE DATA AND SPECIFICATIONS (SDS) ....348
General Specifications ..........................................348
Vehicle Speed When Shifting Gears .....................348
Vehicle Speed When Performing and Releasing
Complete Lock-up .................................................349
Vehicle Speed When Performing and Releasing
Slip Lock-up ..........................................................349
Stall Speed ............................................................350
Line Pressure ........................................................350
A/T Fluid Temperature Sensor ..............................350
Turbine Revolution Sensor ....................................350
Vehicle Speed Sensor A/T (Revolution Sensor) ...350
Reverse Brake ......................................................350
Total End Play .......................................................351

PRECAUTIONS
AT-7
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
ACS002L3
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for On Board Diagnostic (OBD) System of A/T and EngineACS002L5
The ECM has an on board diagnostic system. It will light up the malfunction indicator lamp (MIL) to warn the
driver of a malfunction causing emission deterioration.
CAUTION:

Be sure to turn the ignition switch “OFF” and disconnect the battery cable from the negative ter-
minal before any repair or inspection work. The open/short circuit of related switches, sensors,
solenoid valves, etc. will cause the MIL to light up.

Be sure to connect and lock the connectors securely after work. A loose (unlocked) connector will
cause the MIL to light up due to an open circuit. (Be sure the connector is free from water, grease,
dirt, bent terminals, etc.)

Be sure to route and secure the harnesses properly after work. Interference of the harness with a
bracket, etc. may cause the MIL to light up due to a short circuit.

Be sure to connect rubber tubes properly after work. A misconnected or disconnected rubber tube
may cause the MIL to light up due to a malfunction of the EGR system or fuel injection system, etc.

Be sure to erase the unnecessary malfunction information (repairs completed) from the TCM and
ECM before returning the vehicle to the customer.

AT-30
A/T CONTROL SYSTEM
Revision: 2004 November 2004 FX35/FX45
TCM FunctionACS002LF
The function of the TCM is to:

Receive input signals sent from various switches and sensors.

Determine required line pressure, shifting point, lock-up operation, and engine brake operation.

Send required output signals to the respective solenoids.
CONTROL SYSTEM OUTLINE
The automatic transmission senses vehicle operating conditions through various sensors or signals. It always
controls the optimum shift position and reduces shifting and lock-up shocks.
CONTROL SYSTEM DIAGRAM
SENSORS (or SIGNALS)

TCM

ACTUATORS
PNP switch
Accelerator pedal position sensor
Closed throttle position signal
Wide open throttle position signal
Engine speed signal
A/T fluid temperature sensor
Revolution sensor
Vehicle speed signal
Manual mode switch signal
Stop lamp switch signal
Turbine revolution sensor
ATF pressure switchShift control
Line pressure control
Lock-up control
Engine brake control
Timing control
Fail-safe control
Self-diagnosis
CONSULT-II communication line
Duet-EA control
CAN systemInput clutch solenoid valve
Direct clutch solenoid valve
Front brake solenoid valve
High and low reverse clutch
solenoid valve
Low coast brake solenoid valve
Torque converter clutch solenoid
valve
Line pressure solenoid valve
A/T CHECK indicator lamp
Starter relay
Back-up lamp relay
SCIA5325E

A/T CONTROL SYSTEM
AT-31
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
CAN CommunicationACS004PB
SYSTEM DESCRIPTION
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only. For details, refer to LAN-6,
"CAN Communication Unit"
Input/Output Signal of TCMACS002LH
*1: Spare for vehicle speed sensor·A/T (revolution sensor)
*2: Spare for accelerator pedal position signal
*3: If these input and output signals are different, the TCM triggers the fail-safe function.
*4: Used as a condition for starting self-diagnostics; if self-diagnostics are not started, it is judged that there is some kind of error.
*5: CAN communicationsControl itemLine
pressure
controlVehicle
speed
controlShift
controlLock-up
controlEngine
brake
controlFail-safe
function
(*3)Self-diag-
nostics
function
InputAccelerator pedal position signal
(*5)XXXXXXX
Vehicle speed sensor A/T
(revolution sensor)XXXX XX
Vehicle speed sensor MTR
(*1) (*5)XXXX X
Closed throttle position signal
(*5)(*2) X (*2) X X (*2) X (*4) X
Wide open throttle position signal
(*5)(*2) X (*2) X (*2) X (*4) X
Turbine revolution sensor 1 X X X X X
Turbine revolution sensor 2
(for 4th speed only)XX X XX
Engine speed signals
(*5)XX
PNP switch XXXXXX(*4) X
Stop lamp switch signal
(*5)XX(*4) X
A/T fluid temperature sensors 1, 2XXXXXXX
ASCD or
ICCOperation signal
(*5)XXXX
Overdrive cancel
signal
(*5)XXX
TCM power supply voltage signalXXXXX X
Out-
putDirect clutch solenoid (ATF pres-
sure switch 5)XX XX
Input clutch solenoid (ATF pressure
switch 3)XX XX
High and low reverse clutch sole-
noid (ATF pressure switch 6)XX XX
Front brake solenoid (ATF pressure
switch 1)XX XX
Low coast brake solenoid (ATF
pressure switch 2)XX XXX
Line pressure solenoid XXXXXXX
TCC solenoid X X X
Self-diagnostics table
(*5)X
Sta rter rela yXX

A/T CONTROL SYSTEM
AT-37
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
FUNCTION OF ATF PRESSURE SWITCH
Input clutch control valveWhen the input clutch is coupled, adjusts the line pressure to the optimum pressure
(input clutch pressure) and supplies it to the input clutch. (In 4th and 5th gears, adjusts
the clutch pressure.)
Direct clutch control valveWhen the direct clutch is coupled, adjusts the line pressure to the optimum pressure
(direct clutch pressure) and supplies it to the direct clutch. (In 2nd, 3rd, and 4th gears,
adjusts the clutch pressure.)
TCC control valve
TCC control plug
TCC control sleeveSwitches the lock-up to operating or released. Also, by performing the lock-up operation
transiently, lock-up smoothly.
Torque converter lubrication valveOperates during lock-up to switch the torque converter, cooling, and lubrication system
oil path.
Cool bypass valve Allows excess oil to bypass cooler circuit without being fed into it.
Line pressure relief valve Discharges excess oil from line pressure circuit.
N-D accumulator Produces the stabilizing pressure for when N-D is selected.
Manual valveSends line pressure to each circuit according to the select position. The circuits to which
the line pressure is not sent drain. Name Function
Name Function
ATF pressure switch 1 (FR/B)Detects any malfunction in the front brake hydraulic pressure. When it detects any mal-
function, it puts the system into fail-safe mode.
ATF pressure switch 2 (LC/B)Detects any malfunction in the low coast brake hydraulic pressure. When it detects any
malfunction, it puts the system into fail-safe mode.
ATF pressure switch 3 (I/C)Detects any malfunction in the input clutch hydraulic pressure. When it detects any mal-
function, it puts the system into fail-safe mode.
ATF pressure switch 5 (D/C)Detects any malfunction in the direct clutch hydraulic pressure. When it detects any mal-
function, it puts the system into fail-safe mode.
ATF pressure switch 6 (HLR/C)Detects any malfunction in the high and low reverse clutch hydraulic pressure. When it
detects any malfunction, it puts the system into fail-safe mode.