shift INFINITI FX35 2005 Service Manual

SQUEAK AND RATTLE TROUBLE DIAGNOSES GW-7
C
D E
F
G H
J
K L
M A
B
GW
Revision: 2005 July 2005 FX
INSULATOR (Light foam block)
80845-71L00: 30 mm (1.18 in) thick, 30 ×50 mm (1.18 ×1.97 in)
FELT CLOTHTAPE
Used to insulate where movement does not occur. Ideal for instrument panel applications.
68370-4B000: 15 ×25 mm (0.59 ×0.98 in) pad/68239-13E00: 5 mm (0.20 in) wide tape roll. The fol-
lowing materials, not found in the kit, can also be used to repair squeaks and rattles.
UHMW (TEFLON) TAPE
Insulates where slight movement is present. Ideal for instrument panel applications.
SILICONE GREASE
Used in place of UHMW tape that will be visible or not fit.
Note: Will only last a few months.
SILICONE SPRAY
Use when grease cannot be applied.
DUCT TAPE
Use to eliminate movement.
CONFIRM THE REPAIR
Confirm that the cause of a noise is repaired by test driving the vehicle. Operate the vehicle under the same
conditions as when the noise originally occurred. Refer to the notes on the Diagnostic Worksheet.
Generic Squeak and Rattle TroubleshootingAIS003A1
Refer to Table of Contents for specific component removal and installation information.
INSTRUMENT PANEL
Most incidents are caused by contact and movement between:
1. The cluster lid A and instrument panel
2. Acrylic lens and combination meter housing
3. Instrument panel to front pillar garnish
4. Instrument panel to windshield
5. Instrument panel mounting pins
6. Wiring harnesses behind the combination meter
7. A/C defroster duct and duct joint
These incidents can usually be located by tapping or moving the components to duplicate the noise or by
pressing on the components while driving to stop the noise. Most of these incidents can be repaired by apply-
ing felt cloth tape or silicon spray (in hard to reach areas). Urethane pads can be used to insulate wiring har-
ness.
CAUTION:
Do not use silicone spray to isolate a squeak or rattle. If you saturate the area with silicone, you will
not be able to recheck the repair.
CENTER CONSOLE
Components to pay attention to include:
1. Shifter assembly cover to finisher
2. A/C control unit and cluster lid C
3. Wiring harnesses behind audio and A/C control unit
The instrument panel repair and isolation procedures also apply to the center console.
DOORS
Pay attention to the:
1. Finisher and inner panel making a slapping noise
2. Inside handle escutcheon to door finisher
3. Wiring harnesses tapping
4. Door striker out of alignment causing a popping noise on starts and stops
Tapping or moving the components or pressing on them while driving to duplicate the conditions can isolate
many of these incidents. You can usually insulate the areas with felt cloth tape or insulator foam blocks from
the Nissan Squeak and Rattle Kit (J43980) to repair the noise.

IDX-2
ALPHABETICAL INDEX
A
A/C air flow ...................................................... ATC-37
A/C component layout ..................................... ATC-26
A/C compressor clutch removal and installation ...........
ATC-144
A/C compressor mounting ........... ATC-141, ATC-144,
ATC-148
, ATC-149, ATC-150, ATC-151, ATC-152,
ATC-154
, ATC-155, ATC-156, ATC-157
A/C compressor precaution ............................. ATC-13
A/C compressor special service tool ................ ATC-17
A/C control operation (auto A/C) ...................... ATC-34
A/C diagnostic work flow (auto A/C) .............. ATC-102
A/C evaporator ............................................... ATC-156
A/C HFC134a (R134a) system precaution ........ ATC-6
A/C HFC134a (R134a) system service procedure .......
ATC-138
A/C HFC134a (R134a) system service tools ... ATC-18
A/C HFC134a system service equipment precaution ...
ATC-13
A/C lubricant (R134a) ...................................... ATC-27
A/C lubrication oil ........................................... ATC-162
A/C operational check ...................................... ATC-61
A/C self-diagnoses (auto A/C) ........ ATC-53, ATC-102
A/C service data specification ........................ ATC-162
A/C system description (auto A/C) ................... ATC-30
A/C trouble diagnoses (auto A/C) .................... ATC-40
A/C, A - Wiring diagram ................................... ATC-46
A/T fluid checking ...................... AT-13, AT-52, MA-29
A/T fluid cooler cleaning .................................... AT-15
A/T fluid replacement ............................. AT-12, MA-31
A/T fluid temperature sensor ........................... AT-136
A/T IND - Wiring diagram .................................... DI-54
A/T self-diagnoses ........................................... AT-103
A/T shift lock system ........................................ AT-236
A/T shift lock system - Wiring diagram ............ AT-237
A/T trouble diagnoses ........................................ AT-43
A/T Wiring diagram AT - CAN .......................... AT-107
A/T Wiring diagram AT - FTS .......................... AT-137
A/T Wiring diagram AT - MAIN ........................ AT-183
A/T Wiring diagram AT - MMSW ..................... AT-171
A/T Wiring diagram AT - NONDTC .................. AT-190
A/T Wiring diagram AT - PNP/SW ................... AT-115
A/T Wiring diagram AT - STSIG ...................... AT-110
A/T Wiring diagram AT - VSS A/T ................... AT-120
Accelerator pedal position (APP) sensor ........ EC-619,
EC-626
, EC-640, EC-1302, EC-1309, EC-1323
Accelerator pedal released position learning .... EC-96,
EC-786
AF1B1-Wiring diagram ...... EC-490, EC-499, EC-508,
EC-518
, EC-529, EC-539, EC-551
AF1B2-Wiring diagram ...... EC-492, EC-501, EC-510,
EC-520
, EC-531, EC-541, EC-553
AF1HB1-Wiring diagram .................................. EC-407
AF1HB2-Wiring diagram .................................. EC-409
Air bag .............................................................. SRS-3
Air bag precautions ........................................... SRS-3
Air cleaner and air duct(VK45DE) ................... EM-176
Air cleaner and air duct(VQ35DE) .................... EM-17
Air cleaner filter replacement ............................ MA-25
Air cleaner filter replacement(VQ35DE) ............ MA-18
Air cleaner filter(VQ35DE) ................................ EM-18
Air conditioner cut control ................... EC-35, EC-726
Air flow meter - See Mass air flow sensor ....... EC-186,
EC-195
, EC-893, EC-902
Air fuel ratio sensor 1 ......... EC-488, EC-497, EC-506,
EC-516
, EC-526, EC-536, EC-548
Air fuel ratio sensor 1 heater ............................ EC-405
Air mix. door motor ......................... ATC-73, ATC-132
Ambient sensor ............................. ATC-104, ATC-117
Angular tightening application ............................. EM-6
Angular tightening application(VK45DE) ........ EM-164
APPS1 - Wiring diagram ................. EC-621, EC-1304
APPS2 - Wiring diagram ................. EC-628, EC-1311
APPS3 - Wiring diagram ................. EC-642, EC-1325
ASC/BS - Wiring diagram ............... EC-599, EC-1273
ASC/SW - Wiring diagram .............. EC-583, EC-1256
ASCBOF - Wiring diagram .............. EC-689, EC-1379
ASCD .................................................. EC-36, EC-727
ASCD (automatic speed control device) ........... ACS-3
ASCIND - Wiring diagram ............... EC-696, EC-1386
Ashtray illumination .......................................... LT-157
AT indicator lamp ................................................ DI-54
Auto air conditioner - Wiring diagram ............. ATC-46
Auto amp ...................................................... ATC-116
Auto anti-dazzling inside mirror ....................... GW-84
Automatic amplifier ........... ATC-51, ATC-63, ATC-116
Automatic transmission fluid replacement ........ MA-32
AV and NAVI control unit ................................... AV-89
AV communication line .................................... AV-114
AWD - Wiring diagram ....................................... TF-17
Axle ................................................................... MA-37
Axle housing (rear) ........................................... RAX-7
B
Back Door ........................................................ BL-164
Back door ......................................................... BL-164
Back door opener - See Back door .................. BL-168
BACK/L - Wiring diagram ................................. LT-127
Back-up lamp ................................................... LT-127
Basic inspection ............................................... EC-769
Battery ................................................................. SC-4
Battery/Starting/Charging System Tester SC-6, SC-13,
SC-26
BCM (Body control module) .............................. BCS-3
Block heater(VK45DE) .................................... EM-245
Block heater(VQ35DE) ................................... EM-122
Blower motor ................................... ATC-79, ATC-123
Blower unit .................................................... ATC-121
Board computer ................................................. AV-58
Brake booster .................................................... BR-15
Brake fluid level ................................................ MA-35
Brake hydraulic line ........................................... BR-11
Brake inspection ............................................... MA-36
Brake lines and cables inspection .................... MA-35
Brake master cylinder ........................................ BR-13
Brake switch ................................... EC-614, EC-1297

IDX-7
A
C
D E
F
G H
I
J
K L
B
IDX
ALPHABETICAL INDEX
Pressure switch 6 ...............................
AT-164, AT-181
Pressure test (A/T) ............................................ AT-54
Propeller shaft ........................................... PR-4, PR-7
Propeller shaft on vehicle service .............. PR-4, PR-7
Propeller shaft vibration ............................. PR-4, PR-7
PS/SEN - Wiring diagram ................ EC-398, EC-1130
R
R/VIEW - Wiring diagram ................................. DI-117
Radiator(VK45DE) ............................................. CO-41
Radiator(VQ35DE) ............................................ CO-14
Rear axle ........................................................... RAX-5
Rear bumper ........................................................ EI-17
Rear combination lamp removal and installation ..........
LT-149
Rear door ............................................ BL-153, GW-80
Rear seat ......................................................... SE-106
Rear suspension ............................................... RSU-5
Rear view monitor ............................................. DI-114
Rear washer .................................................... WW-38
Rear window defogger ...................................... GW-86
Rear wiper ....................................................... WW-38
Refrigerant connection precaution ..................... ATC-8
Refrigerant discharging evacuating charging ATC-138
Refrigerant general precaution .......................... ATC-7
Refrigerant lines ............................................ ATC-138
Refrigerant pressure sensor ........... EC-674, EC-1364,
ATC-90
, ATC-156
Refrigeration cycle ........................................... ATC-21
Removal and installation (A/T) ........... AT-270, AT-273
Removal and installation (Transfer) .................... TF-44
Revolution sensor (A/T) ...................... AT-118, AT-263
Rocker cover(VK45DE) ................................... EM-197
Rocker cover(VQ35DE) ..................................... EM-51
Room lamp - See Interior lamp ......................... LT-159
ROOM/L - Wiring diagram ................................ LT-167
RP/SEN - Wiring diagram ................ EC-675, EC-1365
S
Seal - See Exterior .............................................. EI-27
SEAT - Wiring diagram ...................................... SE-93
Seat belt inspection ............................................. SB-6
Seat belt, front ..................................................... SB-3
Seat, rear ......................................................... SE-106
Self-diagnosis (Transfer) .................................... TF-22
SEN/PW - Wiring diagram ............... EC-484, EC-1230
SHIFT - Wiring diagram ................................... AT-237
Shift change signal ........................................ EC-1290
Shift lock system .............................................. AT-236
Shift schedule .................................................. AT-351
Shock absorber (rear) ....................................... RSU-9
Side air bag (satellite) sensor .......................... SRS-43
Side curtain air bag .......................................... SRS-40
Side trim .............................................................. EI-36
SMJ (super multiple junction) ............................ PG-78
SNOW MODE SW ......................................... EC-1388
SNOWSW - Wiring diagram .......................... EC-1389
Spark plug replacement .................................... MA-27
Spark plug replacement(VQ35DE) ................... MA-20
Spark plug(VK45DE) ...................................... EM-190
Spark plug(VQ35DE) ........................................ EM-43
Specification value ............................. EC-153, EC-844
Speedometer ........................................................ DI-5
Spiral cable ..................................................... SRS-37
Spot lamp .......................................................... LT-187
SROOF - Wiring diagram ..................... BL-172, RF-14
SRS - See Supplemental Restraint System ..... SRS-5
SRS - Wiring diagram ..................................... SRS-11
SRS Trouble diagnoses .................................... SRS-7
Stabilizer bar (rear) ......................................... RSU-16
Stall test (A/T) .................................................... AT-52
Standardized relay ............................................. PG-80
START - Wiring diagram .................................... SC-11
Starter ................................................................ SC-10
Starting system .................................................. SC-10
Steering gear and linkage inspection ................ MA-36
Steering linkage ................................................. PS-19
Steering wheel and column ................... PS-10, PS-12
Steering wheel turning force .............................. PS-10
Step lamp .......................................................... LT-126
Stop lamp .......................................................... LT-118
Stop lamp switch .............................. EC-614, EC-1297
STOP/L - Wiring diagram .................................. LT-120
Sun roof, electric ................................................ RF-10
Sunload sensor ............................. ATC-110, ATC-119
Sunroof .................................................. RF-10, RF-25
Supplemental Restraint System ....................... SRS-5
Supplemental restraint system - Wiring diagram ..........
SRS-11
Suspension ....................................................... MA-37
Symbols and abbreviations ...................... GI-10, GI-23
T
Tachometer ........................................................... DI-5
TCM circuit diagram ........................................... AT-51
TCM inspection table ......................................... AT-89
Thermostat(VK45DE) ....................................... CO-53
Thermostat(VQ35DE) ....................................... CO-26
Three way catalyst function (Bank 1) EC-316, EC-1050
Three way catalyst function (Bank 2) EC-316, EC-1050
Three way catalyst precautions ............................ GI-6
Three way catalyst(VK45DE) .......................... EM-182
Three way catalyst(VQ35DE) ........................... EM-26
Throttle control motor ....................... EC-437, EC-1161
Throttle control motor relay .............. EC-432, EC-1156
Throttle position sensor (TPS) .......... EC-213, EC-278,
EC-479
, EC-481, EC-633, EC-920, EC-1015, EC-1225,
EC-1227
, EC-1316
Throttle valve closed position learning ............. EC-786
Tie-rod ............................................................... PS-19
Timing chain(VK45DE) ................................... EM-200
Timing chain(VQ35DE) ..................................... EM-64
Tire rotation ............................................. WT-6, MA-35
Top tether strap child restraint ........................... SB-10
Torque converter installation AT-271, AT-272, AT-276

IP-6
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Revision: 2005 July 2005 FX
INSULATOR (Light foam block)
80845 - 71L00 : 30 mm (1.18 in) thick, 30 × 50 mm (1.18 × 1.97 in)
FELT CLOTH TAPE
Used to insulate where movement does not occur.Ideal for instrument panel applications.
68370 - 4B000 : 15 × 25 mm (0.59 × 0.98 in) pad / 68239-13E00 : 5 mm (0.20 in) wide tape roll The follow-
ing materials, not found in the kit, can also be used to repair squeaks and rattles.
UHMW (TEFLON) TAPE
Insulates where slight movement is present. Ideal for instrument panel applications.
SILICONE GREASE
Used in of UHMW tape that will be visible or not fit.
Note: Will only last a few months.
SILICONE SPRAY
Use when grease cannot be applied.
DUCT TAPE
Use to eliminate movement.
CONFIRM THE REPAIR
Confirm that the cause of a noise is repaired by test driving the vehicle. Operate the vehicle under the same
conditions as when the noise originally occurred. Refer to the notes on the Diagnostic Worksheet.
Generic Squeak and Rattle TroubleshootingAIS003CG
Refer to Table of Contents for specific component removal and installation information.
INSTRUMENT PANEL
Most incidents are caused by contact and movement between:
1. The cluster lid A and instrument panel
2. Acrylic lens and combination meter housing
3. Instrument panel to front pillar garnish
4. Instrument panel to windshield
5. Instrument panel mounting pins
6. Wiring harnesses behind the combination meter
7. A/C defroster duct and duct joint
These incidents can usually be located by tapping or moving the components to duplicate the noise or by
pressing on the components while driving to stop the noise. Most of these incidents can be repaired by apply-
ing felt cloth tape or silicon spray (in hard to reach areas). Urethane pads can be used to insulate wiring har-
ness.
CAUTION:
Do not use silicone spray to isolate a squeak or rattle. If you saturate the area with silicone, you will
not be able to recheck the repair.
CENTER CONSOLE
Components to pay attention to include:
1. Shifter assembly cover to finisher
2. A/C control unit and cluster lid C
3. Wiring harnesses behind audio and A/C control unit
The instrument panel repair and isolation procedures also apply to the center console.
DOORS
Pay attention to the:
1. Finisher and inner panel making a slapping noise
2. Inside handle escutcheon to door finisher
3. Wiring harnesses tapping
4. Door striker out of alignment causing a popping noise on starts and stops
Tapping or moving the components or pressing on them while driving to duplicate the conditions can isolate
many of these incidents. You can usually insulate the areas with felt cloth tape or insulator foam blocks from
the NISSAN Squeak and Rattle Kit (J43980) to repair the noise.

CAN COMMUNICATION LAN-33
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2005 July 2005 FX
Front wiper request signal T R
Front wiper stop position signal R T
Rear window defogger switch sig-
nal TR
Rear window defogger control
signal RRR T
Hood switch signal R T
Theft warning horn request signal T R
Horn chirp signal T R
Steering angle sensor signal T R
ABS warning lamp signal RT
VDC OFF indicator lamp signal R T
SLIP indicator lamp signal RT
Brake warning lamp signal RT
System setting signal TR R
RT T
A/T CHECK indicator lamp signal T R
A/T position indicator lamp signal T R
A/T shift schedule change
demand signal RT
Manual mode signal R T
Not manual mode signal R T
Manual mode shift up signal R T
Manual mode shift down signal R T
Manual mode indicator signal T R
Distance to empty signal R T
Parking brake switch signal R T
Snow mode switch signal R T
Tire pressure signal T R Signals ECM TCM
Dis-
play unit BCM St e e r-
ing
angle
sensor LDW
cam-
era unit Unified
meter and
A/C
amp. ABS
actua-
tor and elec-
tric unit (con-trol
unit) Driver
seat
control unit IPDM
E/R

CAN COMMUNICATION LAN-37
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2005 July 2005 FX
System setting signal TR R
RT T
Distance to empty signal R T
Parking brake switch sig-
nal RT
Door lock/unlock request
signal TR
Door lock/unlock status
signal RT
Starter permission signal T R
Back door open request
signal TR
Power window open
request signal TR
Alarm request signal T R
Key warning signal T R
ICC sensor signal R T
ICC warning lamp signal T R
ICC system display sig-
nal TR
Current gear position sig-
nal TR R
ICC steering switch sig-
nal TR
ASCD operation signal T R
ASCD OD cancel
request signal TR
ICC OD cancel request
signal RT
A/T CHECK indicator
lamp signal TR
A/T position indicator
lamp signal TR
A/T shift schedule
change demand signal R
T
Manual mode signal R T
Not manual mode signal R T
Manual mode shift up
signal RT
Manual mode shift down
signal RT
Manual mode indicator
signal TR R
Signals ECM TCM
Dis-
play
con-
trol
unit ICC
unit Intelli-
gent Key unit BCM Ste er-
ing
angle
sen- sor LDW
cam- era
unit Uni-
fied
meter and
A/C
amp. ICC
sen-
sor ABS
actu- ator and
elec- tric
unit
(con- trol
unit) Driver
seat
con-
trol
unit IPDM
E/R

CAN COMMUNICATION LAN-41
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2005 July 2005 FX
*: VK45DE engine model only ABS warning lamp signal
RT
VDC OFF indicator lamp signal R T
SLIP indicator lamp signal RT
Brake warning lamp signal RT
System setting signal TR R
RT T
AWD warning lamp signal T R
Distance to empty signal R T
Parking brake switch signal R R T
ASCD operation signal T R
ASCD OD cancel request signal T R
A/T CHECK indicator lamp sig-
nal TR
A/T position indicator lamp sig-
nal TR
A/T shift schedule change
demand signal RT
Manual mode signal R T
Not manual mode signal R T
Manual mode shift up signal R T
Manual mode shift down signal R T
Manual mode indicator signal T R
Snow mode switch signal R T
Current gear position signal* R T
Next gear position signal* R T
Shift change signal* R T
Shift pattern signal* R T
Tire pressure signal T R Signals ECM TCM
Dis-
play
unit AWD
con- trol
unit BCM Steer-
ing
angle
sensor LDW
cam- era
unit Uni-
fied
meter and
A/C
amp. ABS
actua- tor
and
elec- tric
unit
(con- trol
unit) Driver
seat
con-
trol
unit IPDM
E/R

LAN-46
[CAN]
CAN COMMUNICATION
Revision: 2005 July 2005 FX
*: VK45DE engine model only A/T shift schedule
change demand sig-
nal R
T
Manual mode signal R T
Not manual mode
signal RT
Manual mode shift up
signal RT
Manual mode shift
down signal RT
Manual mode indica-
tor signal TR
Ignition knob switch
signal TR
Snow mode switch
signal RT
TR
Current gear posi-
tion signal* RT
Next gear position
signal* RT
Shift change signal* R T
Shift pattern signal* R T
VDC OFF switch sig-
nal RT
Signals ECM TCM
Dis-
play
con-
trol
unit AW D
con- trol
unit ICC
unit Intel-
ligent Key unit BCM Steer-
ing
angle
sen- sor LDW
cam- era
unit Uni-
fied
meter and
A/C
amp. ICC
sen-
sor ABS
actu- ator and
elec- tric
unit
(con- trol
unit) Driver
seat
con-
trol
unit IPDM
E/R

HARNESS PG-69
C
D E
F
G H
I
J
L
M A
B
PG
Revision: 2005 July 2005 FX
P/SCKT WW Power Socket
PGC/V EC EVAP Canister Purge Volume Control Solenoid Valve
PHASE EC Camshaft Position Sensor (PHASE)
PHSB1 EC Camshaft Position Sensor (PHASE) (Bank 1)
PHSB2 EC Camshaft Position Sensor (PHASE) (Bank 2)
PNP/SW AT Park/Neutral Position Switch
PNP/SW EC Park/Neutral Position Switch
POS EC Crankshaft Position Sensor (CKPS) (POS)
POWER PG Power Supply Routing
PRE/SE EC EVAP Control System Pressure Sensor
PS/SEN EC Power Steering Pressure Sensor
R/VIEW DI Rear View Camera Control System
ROOM/L LT Interior Room Lamp
RP/SEN EC Refrigerant Pressure Sensor
SEAT SE Power Seat
SEN/PW EC Sensor Power Supply
SHIFT AT A/T Shift Lock System
SNOWSW EC Snow Mode Switch
SROOF RF Sunroof
SRS SRS Supplemental Restraint System
START SC Starting System
STOP/L LT Stop Lamp
STSIG AT Start Signal Circuit
T/WARN WT Low Tire Pressure Warning System
TAIL/L LT Parking, License and Tail Lamps
TPS1 EC Throttle Position Sensor (Sensor 1)
TPS2 EC Throttle Position Sensor (Sensor 2)
TPS3 EC Throttle Position Sensor
TRNSCV BL Homelink Universal Transceiver
TURN LT Turn Signal and Hazard Warning Lamp
VDC BRC Vehicle Dynamics Control System
VEHSEC BL Vehicle Security System
VENT/V EC EVAP Canister Vent Control Valve
VIAS/V EC VIAS Control Solenoid Valve
VSSA/T AT Vehicle Speed Sensor A/T (Revolution Sensor)
WARN DI Warning Lamps
WINDOW GW Power Window
WIP/R WW Rear Wiper and Washer
WIPER WW Front Wiper and Washer Code Section Wiring Diagram Name

RF-6
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Revision: 2005 July 2005 FX
INSULATOR (Light foam block)
80845-71L00: 30 mm (1.18 in) thick, 30 × 50 mm (1.18 × 1.97 in)
FELT CLOTHTAPE
Used to insulate where movement does not occur. Ideal for instrument panel applications.
68370-4B000: 15 × 25 mm (0.59 × 0.98 in) pad/68239-13E00: 5 mm (0.20 in) wide tape roll
The following materials, not found in the kit, can also be used to repair squeaks and rattles.
UHMW(TEFLON) TAPE
Insulates where slight movement is present. Ideal for instrument panel applications.
SILICONE GREASE
Used in place of UHMW tape that will be visible or not fit.
Note: Will only last a few months.
SILICONE SPRAY
Use when grease cannot be applied.
DUCT TAPE
Use to eliminate movement.
CONFIRM THE REPAIR
Confirm that the cause of a noise is repaired by test driving the vehicle. Operate the vehicle under the same
conditions as when the noise originally occurred. Refer to the notes on the Diagnostic Worksheet.
Generic Squeak and Rattle TroubleshootingAIS003AW
Refer to Table of Contents for specific component removal and installation information.
INSTRUMENT PANEL
Most incidents are caused by contact and movement between:
1. Cluster lid A and instrument panel
2. Acrylic lens and combination meter housing
3. Instrument panel to front pillar garnish
4. Instrument panel to windshield
5. Instrument panel mounting pins
6. Wiring harnesses behind the combination meter
7. A/C defroster duct and duct joint
These incidents can usually be located by tapping or moving the components to duplicate the noise or by
pressing on the components while driving to stop the noise. Most of these incidents can be repaired by apply-
ing felt cloth tape or silicon spray (in hard to reach areas).Urethane pads can be used to insulate wiring har-
ness.
CAUTION:
Do not use silicone spray to isolate a squeak or rattle. If you saturate the area with silicone, you will
not be able to recheck the repair.
CENTER CONSOLE
Components to pay attention to include:
1. Shifter assembly cover to finisher
2. A/C control unit and cluster lid C
3. Wiring harnesses behind audio and A/C control unit
The instrument panel repair and isolation procedures also apply to the center console.
DOORS
Pay attention to the:
1. Finisher and inner panel making a slapping noise
2. Inside handle escutcheon to door finisher
3. Wiring harnesses tapping
4. Door striker out of alignment causing a popping noise on starts and stops
Tapping or moving the components or pressing on them while driving to duplicate the conditions can isolate
many of these incidents. You can usually insulate the areas with felt cloth tape or insulator foam blocks from
the Nissan Squeak and Rattle Kit (J43980) to repair the noise.