INFINITI FX35 2006 Manual Online
Page 81 of 4462
ELECTRICAL COMPONENT INSPECTION ACS-73
[ICC]
C 
D  E 
F 
G  H 
I 
J 
L 
M  A 
B
ACS 
Revision: 2006 December 2006 FX35/FX45
ELECTRICAL COMPONENT INSPECTIONPFP:00000
ICC Steering SwitchNKS003FZ
1. Disconnect ICC steering switch. 
2. Check resistance between ICC steering switch connector termi-  nals by pressing each switch.
Booster SolenoidNKS003G1
Disconnect booster solenoid/release switch connector, and measure
resistance between terminals 4 and 6.
Release SwitchNKS003G2
Disconnect booster solenoid/release switch connector and check
resistance between the terminals.
NOTE: 
If pedal is depressed insufficiently, resistance value may remain unchanged.  Terminals Switch Condition Resistance [k 
Ω] 
14 15  MAIN 
Pressed Approx. 0 
Released Approx. 5.5 
CANCEL  Pressed Approx. 0.3 
Released Approx. 5.5 
DISTANCE  Pressed Approx. 0.7 
Released Approx. 5.5 
SET/COAST  Pressed Approx. 1.4 
Released Approx. 5.5 
RESUME/ACCELERATE   Pressed Approx. 2.6 
Released Approx. 5.5
PKIB4169E
Terminals Resistance [  Ω] 
4 6 Approx. 1.4 
PKIC5181E
Condition 1 - 3 1 - 2 2 - 3
Release 
the brake pedal.  Continuity should  
exist.  Continuity should  
not exist.  Continuity should  
not exist. 
Depress 
the brake pedal.  Continuity should  
not exist. (Note)  Continuity should  
exist. (Note)  Continuity should  
not exist.
SKIA1256E 
Page 82 of 4462
ACS-74
[ICC]
ELECTRICAL COMPONENT INSPECTION
Revision: 2006 December 2006 FX35/FX45
ICC Brake Switch and Stop Lamp SwitchNKS003G0
Check each switch after adjusting brake pedal, refer to  BR-6,
"BRAKE PEDAL" .
ICC Brake Hold RelayNKS003IE
Disconnect ICC brake hold relay, and check continuity between ter- 
minals.
Condition  Continuity 
ICC brake switch Stop lamp switch 
When brake pedal is depressed No Yes
When brake pedal is released Yes No
SKIA5984E
Terminals Condition Continuity 
34  Applying battery voltage to  
between terminals 1 and 2.  No 
67 Yes
34  No battery voltage  Ye s 
67 No
PKIC4924E 
Page 83 of 4462
REMOVAL AND INSTALLATION ACS-75
[ICC]
C 
D  E 
F 
G  H 
I 
J 
L 
M  A 
B
ACS 
Revision: 2006 December 2006 FX35/FX45
REMOVAL AND INSTALLATIONPFP:00000
ICC UnitNKS003G3
REMOVAL
1. Remove the instrument passenger lower panel. Refer to   IP-10, "INSTRUMENT PANEL ASSEMBLY" . 
2. Remove the ECM.
3. Disconnect ICC unit connector. 
4. Remove a mounting bolt and a nut from ICC unit.
INSTALLATION
Installation is the reverse order of removal.
ICC SensorNKS003G4
REMOVAL
1. Remove the front bumper. Refer to   EI-14, "FRONT BUMPER" . 
2. Disconnect ICC sensor connector. 
3. Remove mounting bolts from ICC sensor.
SKIA5985E
SKIA5986E 
Page 84 of 4462
ACS-76
[ICC]
REMOVAL AND INSTALLATION
Revision: 2006 December 2006 FX35/FX45
INSTALLATION
Installation is the reverse order of removal. 
CAUTION: 
Adjust the laser beam aiming every time the ICC sensor is removed or installed.
ICC Steering SwitchNKS003G5
Refer to   PS-12, "Removal and Installation" . 
Page 85 of 4462
AT-1
AUTOMATIC TRANSMISSION
C  TRANSMISSION/TRANSAXLE
CONTENTS
D E 
F 
G  H 
I 
J 
K  L 
M
SECTION AT
A 
B
AT 
Revision: 2006 December 2006 FX35/FX45
AUTOMATIC TRANSMISSION
INDEX FOR DTC  ...................................................  ..... 5 
Alphabetical Index  ...............................................  ..... 5 
DTC No. Index  ....................................................  ..... 6 
PRECAUTIONS .....................................................  ..... 7 
Precautions for Supplemental Restraint System 
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .............................................................  ..... 7 
Precautions for On Board Diagnostic (OBD) System 
of A/T and Engine  ...............................................  ..... 7 
Precautions .........................................................  ..... 8 
Service Notice or Precautions  .............................  ..... 9 
PREPARATION ......................................................  ... 10 
Special Service Tools  ..........................................  ... 10 
Commercial Service Tools ...................................  .... 11 
A/T FLUID  ..............................................................  ... 12 
Changing A/T Fluid  .............................................  ... 12 
Checking A/T Fluid  ..............................................  ... 13 
A/T Fluid Cooler Cleaning  ...................................  ... 15 
A/T CONTROL SYSTEM  .......................................  ... 18 
Cross-sectional View (2WD Models)  ...................  ... 18 
Cross-sectional View (VQ35DE Models for AWD)   ... 19 
Cross-sectional View (VK45DE Models for AWD)   ... 20 
Shift Mechanism ..................................................  ... 21 
TCM Function ......................................................  ... 32 
CAN Communication ...........................................  ... 33 
Input/Output Signal of TCM .................................  ... 33 
Line Pressure Control  .........................................  ... 34 
Shift Control  ........................................................  ... 35 
Lock-up Control  ...................................................  ... 37 
Engine Brake Control  ..........................................  ... 38 
Control Valve  .......................................................  ... 38 
ON BOARD DIAGNOSTIC (OBD) SYSTEM  .........  ... 40 
Introduction .........................................................  ... 40 
OBD-II Function for A/T System ..........................  ... 40 
One or Two Trip Detection Logic of OBD-II  .........  ... 40 
OBD-II Diagnostic Trouble Code (DTC)  ..............  ... 40 
Malfunction Indicator Lamp (MIL) ........................  ... 43 
TROUBLE DIAGNOSIS  .........................................  ... 44 
DTC Inspection Priority Chart  .............................  ... 44 
Fail-safe ..............................................................  ... 44 How to Perform Trouble Diagnosis for Quick and  
Accurate Repair  ...................................................  ... 46 
A/T Electrical Parts Location  ...............................  ... 51 
Circuit Diagram  ....................................................  ... 52 
Inspections Before Trouble Diagnosis  .................  ... 53 
Check Before Engine Is Started  ..........................  ... 57 
Check at Idle ........................................................  ... 57 
Cruise Test - Part 1  ..............................................  ... 58 
Cruise Test - Part 2  ..............................................  ... 60 
Cruise Test - Part 3  ..............................................  ... 61 
Vehicle Speed at Which Gear Shifting Occurs  ....  ... 62 
Vehicle Speed at Which Lock-up Occurs/Releases   ... 63 
Symptom Chart ....................................................  ... 64 
TCM Input/Output Signal Reference Values ........  ... 89 
CONSULT-II Function (A/T)  .................................  ... 90 
Diagnostic Procedure without CONSULT-II  .........  .102 
DTC U1000 CAN COMMUNICATION LINE ...........  .104 
Description ...........................................................  .104 
On Board Diagnosis Logic  ...................................  .104 
Possible Cause ....................................................  .104 
DTC Confirmation Procedure  ..............................  .104 
Wiring Diagram — AT — CAN .............................  .105 
Diagnostic Procedure  ..........................................  .106 
DTC P0615 START SIGNAL CIRCUIT  ..................  .107 
Description ...........................................................  .107 
CONSULT-II Reference Value  .............................  .107 
On Board Diagnosis Logic  ...................................  .107 
Possible Cause ....................................................  .107 
DTC Confirmation Procedure  ..............................  .107 
Wiring Diagram — AT — STSIG  .........................  .108 
Diagnostic Procedure  ..........................................  .109 
DTC P0700 TCM  ....................................................  .. 111 
Description ...........................................................  ..111 
On Board Diagnosis Logic  ...................................  ..111 
Possible Cause ....................................................  ..111 
DTC Confirmation Procedure  ..............................  ..111 
Diagnostic Procedure  ..........................................  ..111 
DTC P0705 PARK/NEUTRAL POSITION SWITCH   .112 
Description ...........................................................  .112 
CONSULT-II Reference Value  .............................  .112 
Page 86 of 4462
AT-2Revision: 2006 December 2006 FX35/FX45 On Board Diagnosis Logic  ................................... 
.112 
Possible Cause ....................................................  .112 
DTC Confirmation Procedure  ..............................  .112 
Wiring Diagram — AT — PNP/SW  ......................  .113 
Diagnostic Procedure  ..........................................  .114 
DTC P0717 TURBINE REVOLUTION SENSOR  ...  .116 
Description ...........................................................  .116 
CONSULT-II Reference Value  .............................  .116 
On Board Diagnosis Logic  ...................................  .116 
Possible Cause ....................................................  .116 
DTC Confirmation Procedure  ..............................  .116 
Diagnostic Procedure  ..........................................  .117 
DTC P0720 VEHICLE SPEED SENSOR A/T (REV-
OLUTION SENSOR)  ..............................................  .118 
Description ...........................................................  .118 
CONSULT-II Reference Value  .............................  .118 
On Board Diagnosis Logic  ...................................  .118 
Possible Cause ....................................................  .118 
DTC Confirmation Procedure  ..............................  .118 
Wiring Diagram — AT — VSSA/T ........................  .120 
Diagnostic Procedure  ..........................................  .121 
DTC P0725 ENGINE SPEED SIGNAL  ..................  .123 
Description ...........................................................  .123 
CONSULT-II Reference Value  .............................  .123 
On Board Diagnosis Logic  ...................................  .123 
Possible Cause ....................................................  .123 
DTC Confirmation Procedure  ..............................  .123 
Diagnostic Procedure  ..........................................  .124 
DTC P0740 TORQUE CONVERTER CLUTCH 
SOLENOID VALVE  ................................................  .125 
Description ...........................................................  .125 
CONSULT-II Reference Value  .............................  .125 
On Board Diagnosis Logic  ...................................  .125 
Possible Cause ....................................................  .125 
DTC Confirmation Procedure  ..............................  .125 
Diagnostic Procedure  ..........................................  .126 
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)   .127 
Description ...........................................................  .127 
CONSULT-II Reference Value  .............................  .127 
On Board Diagnosis Logic  ...................................  .127 
Possible Cause ....................................................  .127 
DTC Confirmation Procedure  ..............................  .127 
Diagnostic Procedure  ..........................................  .128 
DTC P0745 LINE PRESSURE SOLENOID VALVE   .129 
Description ...........................................................  .129 
CONSULT-II Reference Value  .............................  .129 
On Board Diagnosis Logic  ...................................  .129 
Possible Cause ....................................................  .129 
DTC Confirmation Procedure  ..............................  .129 
Diagnostic Procedure  ..........................................  .130 
DTC P1705 THROTTLE POSITION SENSOR  ......  .131 
Description ...........................................................  .131 
CONSULT-II Reference Value  .............................  .131 
On Board Diagnosis Logic  ...................................  .131 
Possible Cause ....................................................  .131 
DTC Confirmation Procedure  ..............................  .131 
Diagnostic Procedure  ..........................................  .132 
DTC P1710 A/T FLUID TEMPERATURE SENSOR 
CIRCUIT .................................................................  .134 Description ........................................................... 
.134 
CONSULT-II Reference Value ..............................  .134 
On Board Diagnosis Logic  ...................................  .134 
Possible Cause  ....................................................  .134 
DTC Confirmation Procedure ...............................  .134 
Wiring Diagram — AT — FTS  ..............................  .135 
Diagnostic Procedure ...........................................  .136 
Component Inspection  .........................................  .138 
DTC P1721 VEHICLE SPEED SENSOR MTR  ......  .139 
Description ...........................................................  .139 
CONSULT-II Reference Value ..............................  .139 
On Board Diagnosis Logic  ...................................  .139 
Possible Cause  ....................................................  .139 
DTC Confirmation Procedure ...............................  .139 
Diagnostic Procedure ...........................................  .140 
DTC P1730 A/T INTERLOCK  ................................  .141 
Description ...........................................................  .141 
On Board Diagnosis Logic  ...................................  .141 
Possible Cause  ....................................................  .141 
DTC Confirmation Procedure ...............................  .141 
Judgement of A/T Interlock  ..................................  .141 
Diagnostic Procedure ...........................................  .142 
DTC P1731 A/T 1ST ENGINE BRAKING  ..............  .144 
Description ...........................................................  .144 
CONSULT-II Reference Value ..............................  .144 
On Board Diagnosis Logic  ...................................  .144 
Possible Cause  ....................................................  .144 
DTC Confirmation Procedure ...............................  .144 
Diagnostic Procedure ...........................................  .145 
DTC P1752 INPUT CLUTCH SOLENOID VALVE  .  .146 
Description ...........................................................  .146 
CONSULT-II Reference Value ..............................  .146 
On Board Diagnosis Logic  ...................................  .146 
Possible Cause  ....................................................  .146 
DTC Confirmation Procedure ...............................  .146 
Diagnostic Procedure ...........................................  .147 
DTC P1754 INPUT CLUTCH SOLENOID VALVE 
FUNCTION .............................................................  .148 
Description ...........................................................  .148 
CONSULT-II Reference Value ..............................  .148 
On Board Diagnosis Logic  ...................................  .148 
Possible Cause  ....................................................  .148 
DTC Confirmation Procedure ...............................  .148 
Diagnostic Procedure ...........................................  .149 
DTC P1757 FRONT BRAKE SOLENOID VALVE  ..  .150 
Description ...........................................................  .150 
CONSULT-II Reference Value ..............................  .150 
On Board Diagnosis Logic  ...................................  .150 
Possible Cause  ....................................................  .150 
DTC Confirmation Procedure ...............................  .150 
Diagnostic Procedure ...........................................  .151 
DTC P1759 FRONT BRAKE SOLENOID VALVE 
FUNCTION .............................................................  .152 
Description ...........................................................  .152 
CONSULT-II Reference Value ..............................  .152 
On Board Diagnosis Logic  ...................................  .152 
Possible Cause  ....................................................  .152 
DTC Confirmation Procedure ...............................  .152 
Diagnostic Procedure ...........................................  .153 
Page 87 of 4462
AT-3
D E 
F 
G  H 
I 
J 
K  L 
M  A 
B
AT 
Revision: 2006 December 2006 FX35/FX45  DTC P1762 DIRECT CLUTCH SOLENOID VALVE  
. 154 
Description ..........................................................  . 154 
CONSULT-II Reference Value  .............................  . 154 
On Board Diagnosis Logic  ..................................  . 154 
Possible Cause  ...................................................  . 154 
DTC Confirmation Procedure  ..............................  . 154 
Diagnostic Procedure  ..........................................  . 155 
DTC P1764 DIRECT CLUTCH SOLENOID VALVE 
FUNCTION .............................................................  . 156 
Description ..........................................................  . 156 
CONSULT-II Reference Value  .............................  . 156 
On Board Diagnosis Logic  ..................................  . 156 
Possible Cause  ...................................................  . 156 
DTC Confirmation Procedure  ..............................  . 156 
Diagnostic Procedure  ..........................................  . 157 
DTC P1767 HIGH AND LOW REVERSE CLUTCH 
SOLENOID VALVE  ................................................  . 158 
Description ..........................................................  . 158 
CONSULT-II Reference Value  .............................  . 158 
On Board Diagnosis Logic  ..................................  . 158 
Possible Cause  ...................................................  . 158 
DTC Confirmation Procedure  ..............................  . 158 
Diagnostic Procedure  ..........................................  . 159 
DTC P1769 HIGH AND LOW REVERSE CLUTCH 
SOLENOID VALVE FUNCTION  ............................  . 160 
Description ..........................................................  . 160 
CONSULT-II Reference Value  .............................  . 160 
On Board Diagnosis Logic  ..................................  . 160 
Possible Cause  ...................................................  . 160 
DTC Confirmation Procedure  ..............................  . 160 
Diagnostic Procedure  ..........................................  . 161 
DTC P1772 LOW COAST BRAKE SOLENOID  
VALVE ....................................................................  . 162 
Description ..........................................................  . 162 
CONSULT-II Reference Value  .............................  . 162 
On Board Diagnosis Logic  ..................................  . 162 
Possible Cause  ...................................................  . 162 
DTC Confirmation Procedure  ..............................  . 162 
Diagnostic Procedure  ..........................................  . 163 
DTC P1774 LOW COAST BRAKE SOLENOID 
VALVE FUNCTION  ................................................  . 164 
Description ..........................................................  . 164 
CONSULT-II Reference Value  .............................  . 164 
On Board Diagnosis Logic  ..................................  . 164 
Possible Cause  ...................................................  . 164 
DTC Confirmation Procedure  ..............................  . 164 
Diagnostic Procedure  ..........................................  . 165 
DTC P1815 MANUAL MODE SWITCH  .................  . 166 
Description ..........................................................  . 166 
CONSULT-II Reference Value in Data Monitor Mode  . 166
On Board Diagnosis Logic  ..................................  . 166 
Possible Cause  ...................................................  . 166 
DTC Confirmation Procedure  ..............................  . 166 
Wiring Diagram — AT — MMSW  ........................  . 167 
Diagnostic Procedure  ..........................................  . 169 
Component Inspection  ........................................  . 170 
DTC P1841 ATF PRESSURE SWITCH 1  ..............  . 171 
Description ..........................................................  . 171 CONSULT-II Reference Value  ............................. 
.171 
On Board Diagnosis Logic  ...................................  .171 
Possible Cause ....................................................  .171 
DTC Confirmation Procedure  ..............................  .171 
Diagnostic Procedure  ..........................................  .172 
DTC P1843 ATF PRESSURE SWITCH 3  ..............  .173 
Description ...........................................................  .173 
CONSULT-II Reference Value  .............................  .173 
On Board Diagnosis Logic  ...................................  .173 
Possible Cause ....................................................  .173 
DTC Confirmation Procedure  ..............................  .173 
Diagnostic Procedure  ..........................................  .174 
DTC P1845 ATF PRESSURE SWITCH 5  ..............  .175 
Description ...........................................................  .175 
CONSULT-II Reference Value  .............................  .175 
On Board Diagnosis Logic  ...................................  .175 
Possible Cause ....................................................  .175 
DTC Confirmation Procedure  ..............................  .175 
Diagnostic Procedure  ..........................................  .176 
DTC P1846 ATF PRESSURE SWITCH 6  ..............  .177 
Description ...........................................................  .177 
CONSULT-II Reference Value  .............................  .177 
On Board Diagnosis Logic  ...................................  .177 
Possible Cause ....................................................  .177 
DTC Confirmation Procedure  ..............................  .177 
Diagnostic Procedure  ..........................................  .178 
MAIN POWER SUPPLY AND GROUND CIRCUIT   .179 
Wiring Diagram — AT — MAIN  ...........................  .179 
Diagnostic Procedure  ..........................................  .180 
CLOSED THROTTLE POSITION AND WIDE OPEN 
THROTTLE POSITION CIRCUIT ...........................  .183 
CONSULT-II Reference Value  .............................  .183 
Diagnostic Procedure  ..........................................  .183 
BRAKE SIGNAL CIRCUIT .....................................  .184 
CONSULT-II Reference Value  .............................  .184 
Diagnostic Procedure  ..........................................  .184 
A/T INDICATOR CIRCUIT ......................................  .185 
Description ...........................................................  .185 
CONSULT-II Reference Value  .............................  .185 
Diagnostic Procedure  ..........................................  .185 
TROUBLE DIAGNOSIS FOR SYMPTOMS  ...........  .186 
Wiring Diagram — AT — NONDTC  .....................  .186 
A/T CHECK Indicator Lamp Does Not Come On . 189
Engine Cannot Be Started in “P” or “N” Position  .  .190 
In “P” Position, Vehicle Moves When Pushed  .....  .191 
In “N” Position, Vehicle Moves .............................  .192 
Large Shock (“N” to “D” Position)  ........................  .193 
Vehicle Does Not Creep Backward in “R” Position   .196 
Vehicle Does Not Creep Forward in “D” Position . 199
Vehicle Cannot Be Started From D
1 ....................  .201 
A/T Does Not Shift: D
1   →  D2 ............................... .204 
A/T Does Not Shift: D
2   →  D3 ............................... .206 
A/T Does Not Shift: D
3   →  D4 ............................... .208 
A/T Does Not Shift: D
4   →  D5 ............................... .211 
A/T Does Not Lock-up  .........................................  .213 
A/T Does Not Hold Lock-up Condition .................  .215 
Lock-up Is Not Released  .....................................  .217 
Engine Speed Does Not Return to Idle  ...............  .217 
Cannot Be Changed to Manual Mode  .................  .219 
Page 88 of 4462
AT-4Revision: 2006 December 2006 FX35/FX45 A/T Does Not Shift: 5th Gear  
→ 4th Gear  ........... .219 
A/T Does Not Shift: 4th Gear   → 3rd Gear  ........... .221 
A/T Does Not Shift: 3rd Gear   → 2nd Gear  .......... .223 
A/T Does Not Shift: 2nd Gear   → 1st Gear ........... .225 
Vehicle Does Not Decelerate by Engine Brake  ...  .227 
SHIFT CONTROL SYSTEM  ...................................  .229 
Control Device Removal and Installation  .............  .229 
Control Rod Removal and Installation  .................  .230 
Adjustment of A/T Position  ..................................  .231 
Checking of A/T Position  .....................................  .231 
A/T SHIFT LOCK SYSTEM ....................................  .232 
Description ...........................................................  .232 
Shift Lock System Electrical Parts Location  ........  .232 
Wiring Diagram — AT — SHIFT  ..........................  .233 
Diagnostic Procedure  ..........................................  .234 
KEY INTERLOCK CABLE  .....................................  .236 
Components ........................................................  .236 
Removal and Installation  .....................................  .237 
ON-VEHICLE SERVICE  .........................................  .239 
Control Valve with TCM and A/T Fluid Temperature 
Sensor 2  ..............................................................  .239 
Parking Components (2WD Models Only)  ...........  .251 
Rear Oil Seal  .......................................................  .258 
Revolution Sensor Components (2WD Models 
Only) ....................................................................  .259 
AIR BREATHER HOSE ..........................................  .264 
Removal and Installation  .....................................  .264 
TRANSMISSION ASSEMBLY  ...............................  .266 
Removal and Installation (2WD Models)  .............  .266 
Removal and Installation (AWD Models)  .............  .269 OVERHAUL ............................................................ 
.274 
Components .........................................................  .274 
Oil Channel  ..........................................................  .288 
Locations of Adjusting Shims, Needle Bearings, 
Thrust Washers and Snap Rings  .........................  .291 
DISASSEMBLY ......................................................  .294 
Disassembly .........................................................  .294 
REPAIR FOR COMPONENT PARTS  .....................  .312 
Oil Pump  ..............................................................  .312 
Front Sun Gear, 3rd One-way Clutch ...................  .315 
Front Carrier, Input Clutch, Rear Internal Gear  ....  .317 
Mid Sun Gear, Rear Sun Gear, High and Low 
Reverse Clutch Hub  .............................................  .323 
High and Low Reverse Clutch  .............................  .329 
Direct Clutch  ........................................................  .332 
ASSEMBLY ............................................................  .335 
Assembly (1)  ........................................................  .335 
Adjustment ...........................................................  .349 
Assembly (2)  ........................................................  .352 
SERVICE DATA AND SPECIFICATIONS (SDS)  ...  .359 
General Specifications  .........................................  .359 
Vehicle Speed at Which Gear Shifting Occurs .....  .359 
Vehicle Speed at Which Lock-up Occurs/Releases   .360 
Stall Speed  ...........................................................  .360 
Line Pressure  .......................................................  .360 
A/T Fluid Temperature Sensor  .............................  .360 
Turbine Revolution Sensor ...................................  .361 
Vehicle Speed Sensor A/T (Revolution Sensor)  ..  .361 
Reverse Brake  .....................................................  .361 
Total End Play  ......................................................  .361 
Page 89 of 4462
INDEX FOR DTC AT-5
D E 
F 
G  H 
I 
J 
K  L 
M  A 
B
AT 
Revision: 2006 December 2006 FX35/FX45
INDEX FOR DTCPFP:00024
Alphabetical Index NCS001AL
NOTE: 
If DTC U1000 is displayed with other DTCs, first perform the trouble diagnosis for “DTC U1000 CAN 
COMMUNICATION”. Refer to   AT- 1 0 4 ,  "
DTC U1000 CAN COMMUNICATION LINE" .
*1: These numbers are prescribed by SAE J2012. 
*2: These malfunctions cannot be displayed MIL if another malfunction is assigned to MIL.  Items 
(CONSULT-II screen terms)   DTC 
Reference page 
OBD-II Except OBD-II 
 CONSULT-II GST
(*1) CONSULT-II only “A/T” 
A/T 1ST E/BRAKING — P1731  AT- 1 4 4
ATF PRES SW 1/CIRC — P1841AT- 1 7 1
ATF PRES SW 3/CIRC — P1843AT- 1 7 3
ATF PRES SW 5/CIRC — P1845AT- 1 7 5
ATF PRES SW 6/CIRC — P1846AT- 1 7 7
A/T INTERLOCK P1730 P1730AT- 1 4 1
A/T TCC S/V FNCTN 
P0744(*2)P0744 AT- 1 2 7
ATF TEMP SEN/CIRC P0710 P1710 AT- 1 3 4
CAN COMM CIRCUIT U1000 U1000AT- 1 0 4
D/C SOLENOID/CIRC P1762 P1762AT- 1 5 4
D/C SOLENOID FNCTN 
P1764(*2)P1764 AT- 1 5 6
ENGINE SPEED SIG — P0725 AT- 1 2 3
FR/B SOLENOID/CIRC P1757 P1757AT- 1 5 0
FR/B SOLENOID FNCT 
P1759(*2)P1759 AT- 1 5 2
HLR/C SOL/CIRC P1767 P1767 AT- 1 5 8
HLR/C SOL FNCTN 
P1769(*2)   P1769 
AT- 1 6 0
I/C SOLENOID/CIRC P1752 P1752 AT- 1 4 6
I/C SOLENOID FNCTN 
P1754(*2)P1754 AT- 1 4 8
L/PRESS SOL/CIRC P0745 P0745 AT- 1 2 9
LC/B SOLENOID/CIRC P1772 P1772AT- 1 6 2
LC/B SOLENOID FNCT 
P1774(*2)P1774 AT- 1 6 4
MANU MODE SW/CIRC — P1815 AT- 1 6 6
PNP SW/CIRC P0705 P0705 AT- 11 2
STARTER RELAY/CIRC — P0615AT- 1 0 7
TCC SOLENOID/CIRC P0740 P0740AT- 1 2 5
TCM P0700 P0700 AT- 111
TP SEN/CIRC A/T — P1705AT- 1 3 1
TURBINE REV S/CIRC P0717 P0717 AT- 11 6
VEH SPD SE/CIR-MTR — P1721AT- 1 3 9
VEH SPD SEN/CIR AT P0720 P0720 AT- 11 8 
Page 90 of 4462
AT-6
INDEX FOR DTC
Revision: 2006 December 2006 FX35/FX45
DTC No. Index NCS001AM
NOTE: 
If DTC U1000 is displayed with other DTCs, first perform the trouble diagnosis for “DTC U1000 CAN 
COMMUNICATION”. Refer to   AT- 1 0 4 ,  "
DTC U1000 CAN COMMUNICATION LINE" .
*1: These numbers are prescribed by SAE J2012. 
*2: These malfunctions cannot be displayed MIL if another malfunction is assigned to MIL.  DTC 
Items 
(CONSULT-II screen terms)  Reference page 
OBD-II Except OBD-II 
CONSULT-II  GST
(*1)CONSULT-II           only “A/T” 
— P0615 STARTER RELAY/CIRC  AT- 1 0 7
P0700 P0700 TCM AT- 111
P0705 P0705 PNP SW/CIRCAT- 11 2
P0710 P1710 ATF TEMP SEN/CIRCAT- 1 3 4
P0717 P0717 TURBINE REV S/CIRC AT- 11 6
P0720 P0720 VEH SPD SEN/CIR ATAT- 11 8
— P0725 ENGINE SPEED SIGAT- 1 2 3
P0740 P0740 TCC SOLENOID/CIRC AT- 1 2 5
P0744(*2)P0744 A/T TCC S/V FNCTNAT- 1 2 7
P0745 P0745 L/PRESS SOL/CIRC AT- 1 2 9
— P1705 TP SEN/CIRC A/TAT- 1 3 1
— P1721 VEH SPD SE/CIR-MTRAT- 1 3 9
P1730 P1730 A/T INTERLOCK AT- 1 4 1
— P1731 A/T 1ST E/BRAKINGAT- 1 4 4
P1752 P1752 I/C SOLENOID/CIRC AT- 1 4 6
P1754(*2)P1754 I/C SOLENOID FNCTNAT- 1 4 8
P1757 P1757 FR/B SOLENOID/CIRC AT- 1 5 0
P1759(*2)P1759 FR/B SOLENOID FNCTAT- 1 5 2
P1762 P1762 D/C SOLENOID/CIRC AT- 1 5 4
P1764(*2)P1764 D/C SOLENOID FNCTNAT- 1 5 6
P1767 P1767 HLR/C SOL/CIRC AT- 1 5 8
P1769(*2)P1769 HLR/C SOL FNCTNAT- 1 6 0
P1772 P1772 LC/B SOLENOID/CIRC AT- 1 6 2
P1774(*2)P1774 LC/B SOLENOID FNCTAT- 1 6 4
— P1815 MANU MODE SW/CIRC AT- 1 6 6
— P1841 ATF PRES SW 1/CIRCAT- 1 7 1
— P1843 ATF PRES SW 3/CIRCAT- 1 7 3
— P1845 ATF PRES SW 5/CIRCAT- 1 7 5
— P1846 ATF PRES SW 6/CIRCAT- 1 7 7
U1000 U1000 CAN COMM CIRCUIT AT- 1 0 4