heater INFINITI FX35 2007 Owner's Manual

THERMOSTAT AND WATER CONTROL VALVE CO-55
[VK45DE]
C
D E
F
G H
I
J
K L
M A
CO
Revision: 2006 July 2007 FX35/FX45
Thermostat and Water Control Valve

Install thermostat and water control valve with the whole circum-
ference of each flange part fit securely inside rubber ring. (The
example in the figure shows thermostat.)

Install thermostat with jiggle valve facing upwards. (The position
deviation may be within the range of ±10 degrees)

Install water control valve with the up-mark facing up and the
frame center part facing upwards. (The position deviation may
be within the range of ±10 degrees)
Water Outlet Pipe and Heater Pipe
First apply a neutral detergent to O-rings, then quickly insert the insertion parts of the water outlet pipe and
heater pipe into the installation holes.
INSPECTION AFTER INSTALLATION

Check for leaks of engine coolant using radiator cap tester adapter [SST: EG17650301 (J33984-A)] and
radiator cap tester (commercial service tool). Refer to CO-38, "
LEAK CHECK" .

Start and warm up engine. Visually check if there is no leaks of engine coolant.
PBIC0157E
PBIC0158E

DI-108
COMPASS
Revision: 2006 July 2007 FX35/FX45
Zone Variation Setting ProcedureNKS003HT
NOTE:
The zone setting is factory preset (“default” setting) to zone 8.
1. Press and hold the inside mirror switch for 6 – 9 seconds.
2. The current zone setting appears on the compass display.
3. Find the current geographical location number in the Zone Varia- tion Chart.
4. Select the new zone number. (Press the inside mirror switch until the new zone number appears on the compass display.)
5. After select the new zone number, the compass display will automatically shows a direction within a few seconds.
6. Preform the following Calibration Procedure for more accurate indications.
Calibration ProcedureNKS003HU
NOTE:
The compass calibrates itself under normal driving conditions. However, occasional circumstances may cause
the compass to operate inaccurately. Example: Driving from rural (wide open) areas to crowded city areas, or
if an aftermarket (i.e., non original equipment) antenna with a magnetic base is attached to the vehicle. Cali-
brate the mirror compass if the display shows only one direction or a limited number of directions.
NOTE:

If “magnetic hats” are used in the dealership for vehicle identification, remove the hat from the vehicle
before performing the following steps. Do NOT put the hat back on the vehicle after the procedure is com-
pleted.

Drive the vehicle to an open level area; away from large metallic objects, structures, and overhead power
lines.

Turn off “non-essential” electrical accessories (rear window defrost, heater/air conditioning, wipers) and
close the doors.
1. Verify the correct compass zone setting for the geographical location. Refer to DI-108, "
Zone Variation
Setting Procedure" .
2. Press and hold the inside mirror switch for more than 9 seconds.
3. “C” is displayed on the compass display, when calibration starts.
4. Drive slowly [less than 8 km/h (5 mph)] in a circle until the “C / CAL” is replaced with primary headings (N, NE, E, SE, S, SW, W, or NW).
NOTE:
This will require driving at least 2 complete 360 degree circles; 3 complete circles may be required.
5. The compass calibration procedure is now complete. The compass should operate normally.
NOTE:
If at any time the compass continually displays the incorrect direction or the reading is erratic or locked,
repeat the calibration procedure.
SEL168Y

EC-2Revision: 2006 July 2007 FX35/FX45
Inspection Procedure ...........................................
.137
Diagnostic Procedure .......................................... .138
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT ...................................................................... .147
Description ........................................................... .147
Diagnostic Procedure .......................................... .147
POWER SUPPLY AND GROUND CIRCUIT .......... .148
Wiring Diagram .................................................... .148
Diagnostic Procedure .......................................... .149
Ground Inspection ............................................... .153
DTC U1000, U1001 CAN COMMUNICATION LINE .155
Description ........................................................... .155
On Board Diagnosis Logic ................................... .155
DTC Confirmation Procedure .............................. .155
Wiring Diagram .................................................... .156
Diagnostic Procedure .......................................... .157
DTC U1010 CAN COMMUNICATION .................... .158
Description ........................................................... .158
On Board Diagnosis Logic ................................... .158
DTC Confirmation Procedure .............................. .158
Diagnostic Procedure .......................................... .159
DTC P0011, P0021 IVT CONTROL ....................... .160
Description ........................................................... .160
CONSULT-II Reference Value in Data Monitor Mode .160
On Board Diagnosis Logic ................................... .161
DTC Confirmation Procedure .............................. .161
Diagnostic Procedure .......................................... .162
Component Inspection ......................................... .163
Removal and Installation ..................................... .163
DTC P0031, P0032, P0051, P0052 A/F SENSOR 1
HEATER ................................................................. .164
Description ........................................................... .164
CONSULT-II Reference Value in Data Monitor Mode .164
On Board Diagnosis Logic ................................... .164
DTC Confirmation Procedure .............................. .164
Wiring Diagram .................................................... .166
Diagnostic Procedure .......................................... .169
Component Inspection ......................................... .171
Removal and Installation ..................................... .171
DTC P0037, P0038, P0057, P0058 HO2S2 HEATER .172
Description ........................................................... .172
CONSULT-II Reference Value in Data Monitor Mode .172
On Board Diagnosis Logic ................................... .172
DTC Confirmation Procedure .............................. .173
Wiring Diagram .................................................... .174
Diagnostic Procedure .......................................... .177
Component Inspection ......................................... .179
Removal and Installation ..................................... .179
DTC P0075, P0081 IVT CONTROL SOLENOID
VALVE .................................................................... .180
Component Description ....................................... .180
CONSULT-II Reference Value in Data Monitor Mode .180
On Board Diagnosis Logic ................................... .180
DTC Confirmation Procedure .............................. .180
Wiring Diagram .................................................... .181 Diagnostic Procedure ...........................................
.185
Component Inspection ......................................... .186
Removal and Installation ...................................... .186
DTC P0101 MAF SENSOR .................................... .187
Component Description ....................................... .187
CONSULT-II Reference Value in Data Monitor Mode .187
On Board Diagnosis Logic ................................... .187
DTC Confirmation Procedure ............................... .188
Overall Function Check ........................................ .189
Wiring Diagram .................................................... .190
Diagnostic Procedure ........................................... .191
Component Inspection ......................................... .194
Removal and Installation ...................................... .195
DTC P0102, P0103 MAF SENSOR ........................ .196
Component Description ....................................... .196
CONSULT-II Reference Value in Data Monitor Mode .196
On Board Diagnosis Logic ................................... .196
DTC Confirmation Procedure ............................... .197
Wiring Diagram .................................................... .198
Diagnostic Procedure ........................................... .199
Component Inspection ......................................... .202
Removal and Installation ...................................... .203
DTC P0112, P0113 IAT SENSOR ........................... .204
Component Description ....................................... .204
On Board Diagnosis Logic ................................... .204
DTC Confirmation Procedure ............................... .204
Wiring Diagram .................................................... .206
Diagnostic Procedure ........................................... .207
Component Inspection ......................................... .208
Removal and Installation ...................................... .208
DTC P0117, P0118 ECT SENSOR ......................... .209
Component Description ....................................... .209
On Board Diagnosis Logic ................................... .209
DTC Confirmation Procedure ............................... .210
Wiring Diagram .................................................... .211
Diagnostic Procedure ........................................... .212
Component Inspection ......................................... .213
Removal and Installation ...................................... .213
DTC P0122, P0123 TP SENSOR ........................... .214
Component Description ....................................... .214
CONSULT-II Reference Value in Data Monitor Mode .214
On Board Diagnosis Logic ................................... .214
DTC Confirmation Procedure ............................... .215
Wiring Diagram .................................................... .216
Diagnostic Procedure ........................................... .217
Component Inspection ......................................... .220
Removal and Installation ...................................... .220
DTC P0125 ECT SENSOR ..................................... .221
Component Description ....................................... .221
On Board Diagnosis Logic ................................... .221
DTC Confirmation Procedure ............................... .222
Diagnostic Procedure ........................................... .222
Component Inspection ......................................... .223
Removal and Installation ...................................... .223
DTC P0127 IAT SENSOR ....................................... .224
Component Description ....................................... .224

EC-7
C
D E
F
G H
I
J
K L
M
EC A
Revision: 2006 July 2007 FX35/FX45
Wiring Diagram ...................................................
. 585
Diagnostic Procedure .......................................... . 586
Component Inspection ........................................ . 589
Removal and Installation ..................................... . 589
DTC P2135 TP SENSOR ....................................... . 590
Component Description ....................................... . 590
CONSULT-II Reference Value in Data Monitor Mode . 590
On Board Diagnosis Logic .................................. . 590
DTC Confirmation Procedure .............................. . 591
Wiring Diagram ................................................... . 592
Diagnostic Procedure .......................................... . 593
Component Inspection ........................................ . 596
Removal and Installation ..................................... . 596
DTC P2138 APP SENSOR .................................... . 597
Component Description ....................................... . 597
CONSULT-II Reference Value in Data Monitor Mode . 597
On Board Diagnosis Logic .................................. . 597
DTC Confirmation Procedure .............................. . 598
Wiring Diagram ................................................... . 599
Diagnostic Procedure .......................................... . 600
Component Inspection ........................................ . 604
Removal and Installation ..................................... . 604
DTC P2A00, P2A03 A/F SENSOR 1 ..................... . 605
Component Description ....................................... . 605
CONSULT-II Reference Value in Data Monitor Mode . 605
On Board Diagnosis Logic .................................. . 605
DTC Confirmation Procedure .............................. . 606
Wiring Diagram ................................................... . 607
Diagnostic Procedure .......................................... . 610
Removal and Installation ..................................... . 616
ASCD BRAKE SWITCH ........................................ . 617
Component Description ....................................... . 617
CONSULT-II Reference Value in Data Monitor Mode . 617
Wiring Diagram ................................................... . 618
Diagnostic Procedure .......................................... . 619
Component Inspection ........................................ . 623
ASCD INDICATOR ................................................ . 624
Component Description ....................................... . 624
CONSULT-II Reference Value in Data Monitor Mode . 624
Wiring Diagram ................................................... . 625
Diagnostic Procedure .......................................... . 626
ELECTRICAL LOAD SIGNAL ............................... . 627
Description .......................................................... . 627
CONSULT-II Reference Value in Data Monitor Mode . 627
Diagnostic Procedure .......................................... . 627
FUEL INJECTOR ................................................... . 629
Component Description ....................................... . 629
CONSULT-II Reference Value in Data Monitor Mode . 629
Wiring Diagram ................................................... . 630
Diagnostic Procedure .......................................... . 631
Component Inspection ........................................ . 635
Removal and Installation ..................................... . 635 FUEL PUMP ...........................................................
.636
Description ........................................................... .636
CONSULT-II Reference Value in Data Monitor Mode .636
Wiring Diagram .................................................... .637
Diagnostic Procedure .......................................... .638
Component Inspection ......................................... .641
Removal and Installation ..................................... .641
ICC BRAKE SWITCH ............................................ .642
Component Description ....................................... .642
CONSULT-II Reference Value in Data Monitor Mode .642
Wiring Diagram .................................................... .643
Diagnostic Procedure .......................................... .644
Component Inspection ......................................... .649
IGNITION SIGNAL ................................................. .650
Component Description ....................................... .650
Wiring Diagram .................................................... .651
Diagnostic Procedure .......................................... .656
Component Inspection ......................................... .661
Removal and Installation ..................................... .662
REFRIGERANT PRESSURE SENSOR ................. .663
Component Description ....................................... .663
Wiring Diagram .................................................... .664
Diagnostic Procedure .......................................... .665
Removal and Installation ..................................... .667
SNOW MODE SWITCH ......................................... .668
Description ........................................................... .668
CONSULT-II Reference Value in the Data Monitor
Mode .................................................................... .668
Wiring Diagram .................................................... .669
Diagnostic Procedure .......................................... .670
Component Inspection ......................................... .672
MIL AND DATA LINK CONNECTOR ..................... .673
Wiring Diagram .................................................... .673
SERVICE DATA AND SPECIFICATIONS (SDS) ... .675
Fuel Pressure ...................................................... .675
Idle Speed and Ignition Timing ............................ .675
Calculated Load Value ......................................... .675
Mass Air Flow Sensor .......................................... .675
Intake Air Temperature Sensor ............................ .675
Engine Coolant Temperature Sensor .................. .675
Air Fuel Ratio (A/F) Sensor 1 Heater ................... .675
Heated Oxygen sensor 2 Heater ......................... .675
Crankshaft Position Sensor (POS) ...................... .675
Camshaft Position Sensor (PHASE) ................... .675
Throttle Control Motor .......................................... .675
Fuel Injector ......................................................... .676
Fuel Pump ........................................................... .676
VK45DE
INDEX FOR DTC .................................................... .677
DTC No. Index ..................................................... .677
Alphabetical Index ............................................... .681
PRECAUTIONS ..................................................... .685
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .............................................................. .685

EC-8Revision: 2006 July 2007 FX35/FX45
Precautions for Procedures without Cowl Top Cover
.685
On Board Diagnostic (OBD) System of Engine and
A/T ....................................................................... .685
Precaution ........................................................... .686
PREPARATION ...................................................... .689
Special Service Tools .......................................... .689
Commercial Service Tools ................................... .690
ENGINE CONTROL SYSTEM ............................... .691
System Diagram .................................................. .691
Multiport Fuel Injection (MFI) System .................. .692
Electronic Ignition (EI) System ............................ .694
Fuel Cut Control (at No Load and High Engine
Speed) ................................................................. .695
AIR CONDITIONING CUT CONTROL ................... .696
Input/Output Signal Chart .................................... .696
System Description .............................................. .696
AUTOMATIC SPEED CONTROL DEVICE (ASCD) .697
System Description .............................................. .697
Component Description ....................................... .698
CAN COMMUNICATION ........................................ .699
System Description .............................................. .699
EVAPORATIVE EMISSION SYSTEM .................... .700
Description ........................................................... .700
Component Inspection ......................................... .703
Removal and Installation ..................................... .704
How to Detect Fuel Vapor Leakage ..................... .704
ON BOARD REFUELING VAPOR RECOVERY
(ORVR) ................................................................... .707
System Description .............................................. .707
Diagnostic Procedure .......................................... .708
Component Inspection ......................................... .710
POSITIVE CRANKCASE VENTILATION .............. .712
Description ........................................................... .712
Component Inspection ......................................... .712
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-
NATS) ..................................................................... .714
Description ........................................................... .714
ON BOARD DIAGNOSTIC (OBD) SYSTEM ......... .715
Introduction .......................................................... .715
Two Trip Detection Logic ..................................... .715
Emission-related Diagnostic Information ............. .716
Malfunction Indicator Lamp (MIL) ........................ .730
OBD System Operation Chart ............................. .732
BASIC SERVICE PROCEDURE ............................ .738
Basic Inspection .................................................. .738
Idle Speed and Ignition Timing Check ................. .743
Procedure After Replacing ECM ......................... .744
VIN Registration .................................................. .744
Accelerator Pedal Released Position Learning ... .745
Throttle Valve Closed Position Learning .............. .745
Idle Air Volume Learning ..................................... .745
Fuel Pressure Check ........................................... .747
TROUBLE DIAGNOSIS ......................................... .749
Trouble Diagnosis Introduction ............................ .749
DTC Inspection Priority Chart .............................. .755
Fail-Safe Chart .................................................... .757
Symptom Matrix Chart ......................................... .758
Engine Control Component Parts Location ......... .762
Vacuum Hose Drawing ........................................ .769 Circuit Diagram ....................................................
.770
ECM Harness Connector Terminal Layout ........... .772
ECM Terminals and Reference Value .................. .772
CONSULT-II Function (ENGINE) ......................... .781
Generic Scan Tool (GST) Function ...................... .793
CONSULT-II Reference Value in Data Monitor .... .796
Major Sensor Reference Graph in Data Monitor
Mode .................................................................... .800
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .802
Description ........................................................... .802
Testing Condition ................................................. .802
Inspection Procedure ........................................... .802
Diagnostic Procedure ........................................... .803
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT ...................................................................... .812
Description ........................................................... .812
Diagnostic Procedure ........................................... .812
POWER SUPPLY AND GROUND CIRCUIT .......... .813
Wiring Diagram .................................................... .813
Diagnostic Procedure ........................................... .814
Ground Inspection ................................................ .819
DTC U1000, U1001 CAN COMMUNICATION LINE .820
Description ........................................................... .820
On Board Diagnosis Logic ................................... .820
DTC Confirmation Procedure ............................... .820
Wiring Diagram .................................................... .821
Diagnostic Procedure ........................................... .822
DTC U1010 CAN COMMUNICATION .................... .823
Description ........................................................... .823
On Board Diagnosis Logic ................................... .823
DTC Confirmation Procedure ............................... .823
Diagnostic Procedure ........................................... .824
DTC P0011, P0021 IVT CONTROL ........................ .825
Description ........................................................... .825
CONSULT-II Reference Value in Data Monitor Mode .826
On Board Diagnosis Logic ................................... .826
DTC Confirmation Procedure ............................... .827
Wiring Diagram .................................................... .828
Diagnostic Procedure ........................................... .831
Component Inspection ......................................... .835
Removal and Installation ...................................... .836
DTC P0031, P0032, P0051, P0052 A/F SENSOR 1
HEATER .................................................................. .837
Description ........................................................... .837
CONSULT-II Reference Value in Data Monitor Mode .837
On Board Diagnosis Logic ................................... .837
DTC Confirmation Procedure ............................... .837
Wiring Diagram .................................................... .838
Diagnostic Procedure ........................................... .841
Component Inspection ......................................... .843
Removal and Installation ...................................... .843
DTC P0037, P0038, P0057, P0058 HO2S2 HEATER .844
Description ........................................................... .844
CONSULT-II Reference Value in Data Monitor Mode .844
On Board Diagnosis Logic ................................... .844
DTC Confirmation Procedure ............................... .845

EC-14Revision: 2006 July 2007 FX35/FX45
Component Inspection .........................................
1286
Removal and Installation ..................................... 1286
DTC P2A00, P2A03 A/F SENSOR 1 ..................... 1287
Component Description ....................................... 1287
CONSULT-II Reference Value in Data Monitor Mode 1287
On Board Diagnosis Logic ................................... 1287
DTC Confirmation Procedure .............................. 1288
Wiring Diagram .................................................... 1289
Diagnostic Procedure .......................................... 1292
Removal and Installation ..................................... 1298
ASCD BRAKE SWITCH ......................................... 1299
Component Description ....................................... 1299
CONSULT-II Reference Value in Data Monitor Mode 1299
Wiring Diagram .................................................... 1300
Diagnostic Procedure .......................................... 1301
Component Inspection ......................................... 1305
ASCD INDICATOR ................................................. 1306
Component Description ....................................... 1306
CONSULT-II Reference Value in Data Monitor Mode 1306
Wiring Diagram .................................................... 1307
Diagnostic Procedure .......................................... 1308
ELECTRICAL LOAD SIGNAL ............................... 1309
Description ........................................................... 1309
CONSULT-II Reference Value in Data Monitor Mode 1309
Diagnostic Procedure .......................................... 1309
FUEL INJECTOR ................................................... 1311
Component Description ....................................... 1311
CONSULT-II Reference Value in Data Monitor Mode
1311
Wiring Diagram .................................................... 1312
Diagnostic Procedure .......................................... 1313
Component Inspection ......................................... 1317
Removal and Installation ..................................... 1317
FUEL PUMP ........................................................... 1318
Description ........................................................... 1318
CONSULT-II Reference Value in Data Monitor Mode 1318
Wiring Diagram .................................................... 1319
Diagnostic Procedure .......................................... 1320
Component Inspection ......................................... 1323
Removal and Installation ..................................... 1323
ICC BRAKE SWITCH ............................................. 1324
Component Description ....................................... 1324
CONSULT-II Reference Value in Data Monitor Mode 1324
Wiring Diagram .................................................... 1325
Diagnostic Procedure ........................................... 1326
Component Inspection ......................................... 1331
IGNITION SIGNAL ................................................. 1332
Component Description ....................................... 1332
Wiring Diagram .................................................... 1333
Diagnostic Procedure ........................................... 1338
Component Inspection ......................................... 1343
Removal and Installation ...................................... 1344
REFRIGERANT PRESSURE SENSOR ................. 1345
Component Description ....................................... 1345
Wiring Diagram .................................................... 1346
Diagnostic Procedure ........................................... 1347
Removal and Installation ...................................... 1349
SNOW MODE SWITCH .......................................... 1350
Description ........................................................... 1350
CONSULT-II Reference Value in the Data Monitor
Mode .................................................................... 1350
Wiring Diagram .................................................... 1351
Diagnostic Procedure ........................................... 1352
Component Inspection ......................................... 1354
VARIABLE INDUCTION AIR CONTROL SYSTEM
(VIAS) ..................................................................... 1355
Description ........................................................... 1355
CONSULT-II Reference Value in Data Monitor Mode 1356
Wiring Diagram .................................................... 1357
Diagnostic Procedure ........................................... 1359
Component Inspection ......................................... 1362
Removal and Installation ...................................... 1363
MIL AND DATA LINK CONNECTOR ..................... 1364
Wiring Diagram .................................................... 1364
SERVICE DATA AND SPECIFICATIONS (SDS) ... 1366
Fuel Pressure ....................................................... 1366
Idle Speed and Ignition Timing ............................. 1366
Calculated Load Value ......................................... 1366
Mass Air Flow Sensor .......................................... 1366
Intake Air Temperature Sensor ............................ 1366
Engine Coolant Temperature Sensor ................... 1366
Fuel Tank Temperature Sensor ............................ 1366
Crankshaft Position Sensor (POS) ...................... 1366
Camshaft Position Sensor (PHASE) .................... 1366
A/F Sensor 1 Heater ............................................ 1366
Heated Oxygen sensor 2 Heater ......................... 1367
Throttle Control Motor .......................................... 1367
Fuel Injector ......................................................... 1367
Fuel Pump ............................................................ 1367

ON BOARD DIAGNOSTIC (OBD) SYSTEM EC-65
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2006 July 2007 FX35/FX45
Item Self-diagnostic test item DTC Test value
(GST display) Test limit Conversion
TID CID
CATALYST Three way catalyst function (Bank 1)
P0420 01H 01H Max. 1/128
P0420 02H 81H Min. 1
Three way catalyst function (Bank 2) P0430 03H 02H Max. 1/128
P0430 04H 82H Min. 1
EVAP SYSTEM EVAP control system (Small leak) P0442 05H 03H Max.
1/128mm
2
EVAP control system purge flow monitoring P0441 06H 83H Min. 20mV
EVAP control system (Very small leak) P0456 07H 03H Max. 1/128mm
2
HO2S Air fuel ratio (A/F) sensor 1 (Bank 1)
P0131 41H 8EH Min. 5 mV
P0132 42H 0EH Max. 5 mV
P2A00 43H 0EH Max. 0.002
P2A00 44H 8EH Min. 0.002 P0133 45H 8EH Min. 0.004
P0130 46H 0EH Max. 5 mV
P0130 47H 8EH Min. 5 mV
P0133 48H 8EH Min. 0.004
Air fuel ratio (A/F) sensor 1 (Bank 2) P0151 4CH 8FH Min. 5 mV
P0152 4DH 0FH Max. 5 mV
P2A03 4EH 0FH Max. 0.002
P2A03 4FH 8FH Min. 0.002 P0153 50H 8FH Min. 0.004
P0150 51H 0FH Max. 5 mV
P0150 52H 8FH Min. 5 mV
P0153 53H 8FH Min. 0.004
Heated oxygen sensor 2 (Bank 1) P0139 19H 86H Min. 10mV/500ms
P0137 1AH 86H Min. 10mV
P0138 1BH 06H Max. 10mV
P0138 1CH 06H Max. 10mV
Heated oxygen sensor 2 (Bank 2) P0159 21H 87H Min. 10mV/500ms
P0157 22H 87H Min. 10mV
P0158 23H 07H Max. 10mV
P0158 24H 07H Max. 10mV
HO2S HTR Air fuel ratio (A/F) sensor 1 heater (Bank 1)
P0032 57H 10H Max. 5 mV
P0031 58H 90H Min. 5 mV
Air fuel ratio (A/F) sensor 1 heater (Bank 2) P0052 59H 11H Max. 5 mV
P0051 5AH 91H Min. 5 mV
Heated oxygen sensor 2 heater (Bank 1) P0038 2DH 0AH Max. 20mV
P0037 2EH 8AH Min. 20mV
Heated oxygen sensor 2 heater (Bank 2) P0058 2FH 0BH Max. 20mV
P0057 30H 8BH Min. 20mV

EC-94
[VQ35DE]
TROUBLE DIAGNOSIS
Revision: 2006 July 2007 FX35/FX45
*: Models with ICC. 2

P0031 P0032 P0051 P0052 Air fuel ratio (A/F) sensor 1 heater

P0037 P0038 P0057 P0058 Heated oxygen sensor 2 heater

P0075 P0081 Intake valve timing control solenoid valve

P0130 P0131 P0132 P0133 P0150 P0151 P0152 P0153 P2A00 P2A03 Air fuel ratio (A/F) sensor 1

P0137 P0138 P0139 P0157 P0158 P0159 Heated oxygen sensor 2

P0441 EVAP control system purge flow monitoring

P0443 P0444 P0445 EVAP canister purge volume control solenoid valve

P0447 P0448 EVAP canister vent control valve

P0451 P0452 P0453 EVAP control system pressure sensor

P0550 Power steering pressure sensor

P0603 ECM power supply

P0710 P0717 P0720 P0740 P0744 P0745 P1730 P1752 P1754 P1757 P1759 P1762 P1764 P1767 P1769 P1772
P1774 A/T related sensors, solenoid valves and switches

P1217 Engine over temperature (OVERHEAT)

P1805 Brake switch

P2100 P2103 P2118 Electric throttle control actuator

P2101 Electric throttle control function
3

P0011 P0021 Intake valve timing control

P0171 P0172 P0174 P0175 Fuel injection system function

P0300 - P0306 Misfire

P0420 P0430 Three way catalyst function

P0442 EVAP control system (SMALL LEAK)

P0455 EVAP control system (GROSS LEAK)

P0456 EVAP control system (VERY SMALL LEAK)

P0506 P0507 Idle speed control system

P1148 P1168 Closed loop control

P1211 TCS control unit

P1212 TCS communication line

P1421 COLD START CONTROL

P1564 ICC steering switch/ASCD steering switch

P1568 ICC command valve*

P1572 ICC brake switch/ASCD brake switch

P1574 ICC vehicle speed sensor/ASCD vehicle speed sensor

P1715 Turbine revolution sensor

P2119 Electric throttle control actuator
Priority Detected items (DTC)

TROUBLE DIAGNOSIS EC-109
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2006 July 2007 FX35/FX45
ECM Harness Connector Terminal LayoutNBS003M4
ECM Terminals and Reference ValueNBS003M5
PREPARATION
ECM is located behind the passenger side instrument lower panel.
For this inspection, remove passenger side instrument lower panel.
ECM INSPECTION TABLE
Specification data are reference values and are measured between each terminal and ground.
Pulse signal is measured by CONSULT-II.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECMs transistor. Use a ground other than ECM terminals, such as the ground.
PBIB3368E
PBIB1578E
TER-
MINAL NO. WIRE
COLOR ITEM CONDITION DATA (DC Voltage)
1 B ECM ground [Engine is running]

Idle speedBody ground
2R/L A/F sensor 1 heater
(bank 1) [Engine is running]

Warm-up condition

Idle speed Approximately 5V
3R Throttle control motor relay
power supply [Ignition switch: ON] BATTERY VOLTAGE
(11 - 14V)
4L/W Throttle control motor
(Close) [Ignition switch: ON]

Engine stopped

Selector lever: D

Accelerator pedal: Fully released 0 - 14V
PBIB1584E
PBIB1104E

EC-110
[VQ35DE]
TROUBLE DIAGNOSIS
Revision: 2006 July 2007 FX35/FX45
5L/B Throttle control motor
(Open) [Ignition switch: ON]
Engine stopped

Selector lever: D

Accelerator pedal: Fully depressed 0 - 14V
6R Heated oxygen sensor 2
heater (bank 2) [Engine is running]

Engine speed: Below 3,600 rpm after the
following conditions are met
–Engine: After warming up
–Keeping the engine speed between 3,500
and 4,000 rpm for 1 minute and at idle for 1
minute under no load 0 - 1.0V
[Ignition switch: ON]

Engine stopped
[Engine is running]

Engine speed: Above 3,600 rpm BATTERY VOLTAGE
(11 - 14V)
10 OR Intake valve timing control
solenoid valve (bank 2) [Engine is running]

Warm-up condition

Idle speed
BATTERY VOLTAGE
(11 - 14V)
[Engine is running]

Warm-up condition

When revving engine up to 2,500 rpm
quickly 7 - 12V
11 B R Intake valve timing control
solenoid valve (bank 1) [Engine is running]

Warm-up condition

Idle speed
BATTERY VOLTAGE
(11 - 14V)
[Engine is running]

Warm-up condition

When revving engine up to 2,500 rpm
quickly 7 - 12V
12 R/G Power steering pressure
sensor [Engine is running]

Steering wheel: Being turned
0.5 - 4.5V
[Engine is running]

Steering wheel: Not being turned 0.4 - 0.8V
TER-
MINAL NO. WIRE
COLOR ITEM CONDITION DATA (DC Voltage)
PBIB1105E
PBIB1790E
PBIB1790E