light INFINITI M 2011 Owners Manual

●The Dual control mode cannot be activated
when the air conditioner is in the front
defrosting mode “
”.
Automatic upper ventilator system:
1. Push the “CLIMATE” button to on.
2. Select the “Upper Vent” key and the indicator on the screen will illuminate.
The air flow against the driver’s or pas-
senger’s upper body becomes gentle.
In this mode, air from the center ventilators
flows both straight and upward in order to
control the cabin temperature without blow-
ing air directly on the occupants.
Distribution between straight and upward flows
is determined automatically by the climate con-
trol system. If you prefer strong air flow against
your upper body, select “Upper Vent” key to
turn the indicator off.
When the outside temperature decreases to
approximately 14°F (10°C), the Upper Vent
function will not activate. The Upper Vent
function will reactivate automatically when am-
bient temperature is approximately 14°F
(10°C) or above.
Display Forest Air™ system setting screen :
The “Forest Air setting” screen will appear when
selecting the “Forest Air Setting” key. For the details about the Forest Air™ system
setting operation, see “Setting Forest Air™”
later in this section.
Display Forest Air™ Information screen :
The Forest Air™ system information screen will
appear when selecting the “Forest Air Info” key.
For details about the Forest Air™ system infor-
mation screen, see “Forest Air™ system Infor-
mation” later in this section.FOREST AIR™
The Forest Air™ system keeps the air inside the
vehicle clean using the automatic air intake
system and automatic ventilation. The Forest
Air™ system also makes the inside of the
vehicle more comfortable, using a combination
of the upper ventilator and center ventilators at
random.
*Forest Air™ is a trademark of Nissan Motor
Co., Ltd.
Main operation
Push the “” button.
(The “
” and “AUTO” indicator light on the
button will illuminate.) When the following functions and sensors are
turned on, the Forest Air™ system settings will
activate.
– Breeze Mode
–
Outside odor and exhaust gas detection sensor
– Inside Air Quality sensor
– Auto humidity control
The fan speed and air flow is automatically set
to the AUTO position.
●
The Forest Air™ system can be adjusted
and/or activated/deactivated for each func-
tion. For details of the Forest Air™ system
settings, see later in this section.
● When the “
” button is pushed while
the air conditioner is off, the air conditioner
will automatically activate.
● The Forest Air™ system automatically turns
off when the outside temperature is below
approximately 32°F (0°C). When the tem-
perature is below approximately 32°F (0°C),
the Forest Air system can not be turned on
when the
button is pressed. This is
not a malfunction. Push the
to reac-
tivate the system when the outside tempera-
ture is above approximately 32°F (0°C). The
Monitor, climate, audio, phone and voice recognition systems4-39
—
—
03/02/10—pattie


indicator light on thebutton illumi-
nates when the system is operating.
● The air flow control is not available in the
front defogger mode. When the “
”
button is pushed while the Forest Air™
system is turned on, the Forest Air™ system
will turn off.
Operating tips
Breeze Mode :
When this mode is ON, fan speed fluctuates
during the Forest Air™ system operation, creat-
ing a wind breeze similar to a natural breeze
using a combination of the upper ventilator and
the center ventilators at random.
● Breeze Mode will activate after the tempera-
ture of the passenger compartment becomes
suitable.
● This function will not operate immediately
after the engine starts.
● Breeze Mode is activated when the air flow
mode is in the 
and mode.
● This function will turn off if the fan speed or
a ventilator outlet is manually adjusted.
● The breeze patterns may change in accor-
dance with the amount of sun load. ●
When operating fan speed or air flow control
while the Forest Air™ system is turned on,
the “
” indicator light on the button will
turn off automatically, and the Breeze Mode
function will turn off.
● When the Breeze Mode function is turned off
while the Forest Air™ system is on, the
Breeze Mode function will remain off until
the “
” button is turned off and on
again.
Outside odor and exhaust gas detection sensor :
This vehicle is equipped with an outside odor
and exhaust gas detection sensor. When the
automatic intake air control is on, the sensor
detects odors and exhaust gas, and then the
system automatically changes from the outside
air circulation mode to the recirculation mode.
When the “
” button is pushed, the out-
side odor and exhaust gas detection sensor will
turn on.
When the Forest Air™ system is on, for the first
40 seconds, the recirculation mode is selected
to prevent dust, dirt and pollen from entering
the vehicle, and the system cleans the air inside
of the vehicle with Plasmacluster ion™ that are
emitted from the ventilator. After 40 seconds,
the outside odor and exhaust gas sensor acti- vates and automatically alternates between the
recirculation mode and outside air circulation
mode.
●
The outside odor and exhaust gas detection
sensor detects industry odors such as pulp
or chemicals, and exhaust gas such as gaso-
line or diesel.
Inside Air Quality sensor :
This vehicle is equipped with an inside air
quality sensor. When the sensor detects odor in
the cabin, the system increases the fan speed
automatically. When the Forest Air™ system is
on, the inside air quality sensor will turn on.
This function will activate approximately 5 min-
utes after the engine has been started.
● The Outside/Inside Air Mix function will turn
off when the air recirculation and outside air
circulation modes are changed manually.
When the Outside/Inside Air Mix function is
not active, turn off and on the Forest Air™
system, the Outside/Inside Air Mix function
will activate again.
Auto humidity control :
The sensor installed on the upper side of the
windshield detects the temperature and humid-
ity of the passenger compartment and the sur-
face of the windshield, and controls the humid-
ity of the passenger compartment to not be
4-40Monitor, climate, audio, phone and voice recognition systems
—
—
03/02/10—pattie


over-dry or moist enough to fog the windows.
Moreover, it detects potential fog before forma-
tion on the windows and operates to remove it.
●Push the “AUTO” or “
” button (The
“AUTO” or “
” indicator light on the
button will illuminate and “AUTO DEF” will
appear on the display.)
● The “Auto humidity control” function will not
operate if the fan speed or a vent outlet is
manually adjusted. (“AUTO DEF” will disap-
pear from the display.)
● When auto humidity control is turned off
while the Forest Air™ system is on, turn off
and on the Forest Air™ system, the auto
humidity control will activate again.
Setting Forest Air™
1. Push the “CLIMATE” button on the instru-
ment panel and turn the display to the
“CLIMATE mode” screen.
2. Select the “Forest Air Setting” key.
The Forest Air™ system settings screen is
displayed.
● No settings, except for auto humidity con-
trol, are available unless the “
” indi-
cator light on the button illuminates.
Breeze Mode ON/OFF :
When this item is turned to ON, the Breeze
Mode function will activate while the Forest
Air™ system operates. Fan Speed Variance :
Set the Breeze Mode fluctuation effect.
Select the “Fan Speed Variance” key and select
the “High” or “Low” key setting of the Breeze
Mode fluctuation effect.
Setting the fan speed to “High” allows a larger
fluctuation change.
Outside/Inside Air Mix :
This item allows the user to set priority between
the outside air circulation and air recirculation
modes.
Select the “Outside/Inside Air Mix” key and use
“
”or“” key to adjust priority.
Greater priority will be given to the air recircu-
lation mode when the indicator is closer to
“
”, and the outside air circulation mode
when the indicator is closer to “
”.
Auto Defogging Sensitivity :
This item allows the user to set the timing of the
automatic defogging activation function.
Select the “Auto Defogging Sensitivity” key and
select the “Slow” or “Fast” key.
When set to OFF, the automatic defogging func-
tion will turn off.
SAA2961
Monitor, climate, audio, phone and voice recognition systems4-41
—
—
03/02/10—pattie


FM radio reception :
Range: FM range is normally limited to 25 to 30
miles (40 to 48 km), with monaural (single
station) FM having slightly more range than
stereo FM. External influences may sometimes
interfere with FM station reception even if the
FM station is within 25 miles (40 km). The
strength of the FM signal is directly related to
the distance between the transmitter and re-
ceiver. FM signals follow a line-of-sight path,
exhibiting many of the same characteristics as
light. For example they will reflect off objects.
Fade and drift: As your vehicle moves away from
a station transmitter, the signals will tend to
fade and/or drift.Static and flutter: During signal interference
from buildings, large hills or due to antenna
position, usually in conjunction with increased
distance from the station transmitter, static or
flutter can be heard. This can be reduced by
lowering the treble setting to reduce the treble
response.
Multipath reception: Because of the reflective
characteristics of FM signals, direct and re-
flected signals reach the receiver at the same
time. The signals may cancel each other, result-
ing in momentary flutter or loss of sound.
AM radio reception :
AM signals, because of their low frequency, can
bend around objects and skip along the ground.
In addition, the signals can be bounced off the
ionosphere and bent back to earth. Because of
these characteristics. AM signals are also sub-
ject to interference as they travel from transmit-
ter to receiver.
Fading: Occurs while the vehicle is passing
through freeway underpasses or in areas with
many tall buildings. It can also occur for several
seconds during ionospheric turbulence even in
areas where no obstacles exist.
Static: Caused by thunderstorms, electrical
power lines, electric signs and even traffic
lights.Satellite radio reception :
When the satellite radio is used for the first time
or the battery has been replaced, the satellite
radio may not work properly. This is not a
malfunction. Wait more than 10 minutes with
the satellite radio ON and the vehicle outside of
any metal or large building for the satellite
radio to receive all of the necessary data.
The satellite radio mode requires an active XM
Satellite Radio subscription. The satellite radio
is not available in Alaska, Hawaii and Guam.
The satellite radio performance may be affected
if cargo carried on the roof blocks the satellite
radio signal.
If possible, do not put cargo near the satellite
antenna.
A build up of ice on the satellite radio antenna
can affect satellite radio performance. Remove
the ice to restore satellite radio reception.
SAA0306
Monitor, climate, audio, phone and voice recognition systems4-45
—
—
07/15/10—tbrooks


Compact Disc (CD) player
●Do not force a compact disc into the CD
insert slot. This could damage the CD and/or
CD player.
● Trying to load a CD with the CD door closed
could damage the CD and/or CD player. ●
During cold weather or rainy days, the player
may malfunction due to the humidity. If this
occurs, remove the CD and dehumidify or
ventilate the player completely.
● The player may skip while driving on rough
roads.
● The CD player sometimes cannot function
when the passenger compartment tempera-
ture is extremely high. Decrease the tem-
perature before use.
● Only use high quality 4.7 in (12 cm) round
discs that have the “COMPACT disc DIGITAL
AUDIO” logo on the disc or packaging.
● Do not expose the CD to direct sunlight.
● CDs that are of poor quality, dirty, scratched,
covered with fingerprints, or that have pin
holes may not work properly.
● The following CDs may not work properly:
– Copy control compact discs (CCCD)
– Recordable compact discs (CD-R)
– Rewritable compact discs (CD-RW)
● Do not use the following CDs as they may
cause the CD player to malfunction.
– 3.1 in (8 cm) discs
– CDs that are not round – CDs with a paper label
– CDs that are warped, scratched, or have
abnormal edges
● This audio system can only play prerecorded
CDs. It has no capabilities to record or burn
CDs.
● If the CD cannot be played, one of the
following messages will be displayed.
CHECK DISC: – Confirm that the CD is inserted correctly (the label side is facing up, etc.).
– Confirm that the CD is not bent or warped and it is free of scratches.
PUSH EJECT:
This is an error due to the temperature inside
the player is too high. Remove the CD by
pushing the EJECT button, and after a short
time reinsert the CD. The CD can be played
when the temperature of the player returns to
normal.
UNPLAYABLE:
The file is unplayable in this audio system
(only MP3 or WMA CD).
SAA0480
4-46Monitor, climate, audio, phone and voice recognition systems
—
—
07/15/10—tbrooks


DVD (Digital Versatile Disc) player
(models with navigation system)
●Do not force a compact disc into the CD/DVD
insert slot. This could damage the CD/DVD
player.
● During cold weather or rainy days, the player
may malfunction due to humidity. If this occurs, remove the CD/DVD and dehumidify
or ventilate the player completely.
● The player may skip while driving on rough
roads.
● The CD/DVD player sometimes cannot func-
tion when the passenger compartment tem-
perature is extremely high. Decrease the
temperature before use.
● Only use high quality 4.7 in (12 cm) round
discs that have the “COMPACT disc DIGITAL
AUDIO” or “DVD Video” logo on the disc or
packaging.
● Do not expose the CD/DVD to direct sunlight.
● CD/DVDs that are of poor quality, dirty,
scratched, covered with fingerprints, or that
have pinholes may not work properly.
● The following CD/DVDs are not guaranteed
to play:
– Copy control compact discs (CCCD)
– Recordable compact discs (CD-R)
– Rewritable compact discs (CD-RW)
– Recordable DVDs (DVD±R, DVD±R DL)
– Rewritable DVDs (DVD±RW, DVD±RW DL) ●
Do not use the following CD/DVDs as they
may cause the CD/DVD player to malfunc-
tion.
– 3.1 in (8 cm) discs
– CD/DVDs that are not round
– CD/DVDs with a paper label
– CD/DVDs that are warped, scratched or have abnormal edges
– This audio system can only play prere- corded CD/DVDs. It has no capabilities to
record or burn CD/DVDs.
● If the CD/DVD cannot be played, one of the
following messages will be displayed.
Disc Read Error:
– Confirm that the CD/DVD is inserted cor- rectly (the label side is facing up, etc.).
– Confirm that the CD/DVD is not bent or warped and it is free of scratches.
Please Eject Disc: – This may be an error due to the tempera- ture inside the player being too high.
Remove the CD/DVD by pushing the EJECT
button, and after a short time reinsert the
CD/DVD. The CD/DVD can be played when
the temperature of the player returns to
LHA0484
Monitor, climate, audio, phone and voice recognition systems4-47
—
—
07/15/10—tbrooks


●A new disc may be rough on the inner and
outer edges. Remove the rough edges by
rubbing the inner and outer edges with the
side of a pen or pencil as illustrated.
USB memory
● Never touch the terminal portion of the USB
memory.
● Do not place heavy objects on the USB
memory.
● Do not store the USB memory in highly
humid locations.
● Do not expose the USB memory to direct
sunlight.
● Do not spill any liquids on the USB memory.
Refer to the USB memory Owner’s Manual for
the details.
1. Audio source switch
2. Menu control switch (models with naviga- tion system) or audio tuning switch (mod-
els without navigation system)
3. Back switch
4. Volume control switch
STEERING-WHEEL-MOUNTED
CONTROLS FOR AUDIO
Menu control switch (models with
navigation system) or audio tuning
switch (models without navigation
system)
While the display is showing a MAP (navigation
systems only), STATUS or Audio screen, tilt the
switch upward or downward to select a station,
track, CD or folder. For most audio sources,
tilting the switch up/down for more than 1.5
seconds provides a different function than tilt-
ing up/down for less than 1.5 seconds.
AM and FM radio :
● Tilting up/down for less than 1.5 seconds
will increase or decrease the preset station.
● Tilting up/down for more than 1.5 seconds
will seek up or down to the next station.
Models with navigation system
SAA2966
Models without navigation system
SAA2967
Monitor, climate, audio, phone and voice recognition systems4-83
—
—
07/15/10—tbrooks


ANTENNA
Window antenna
The antenna pattern is printed inside the rear
window.
CAUTION
●Do not place metalized film near the rear
window glass or attach any metal parts to it.
This may cause poor reception or noise.
● When cleaning the inside of the rear window,
be careful not to scratch or damage the rear
window antenna. Lightly wipe along the an-
tenna with a dampened soft cloth. When installing a car phone or a CB radio in
your INFINITI, be sure to observe the following
cautions, otherwise the new equipment may
adversely affect the electronic control modules
and electronic control system harness.
WARNING
●
A cellular telephone should not be used
while driving so full attention may be given
to vehicle operation. Some jurisdictions pro-
hibit the use of cellular telephones while
driving.
● If you must make a call while your vehicle is
in motion, the hands-free cellular phone op-
erational mode (if so equipped) is highly rec-
ommended. Exercise extreme caution at all
times so full attention may be given to ve-
hicle operation.
● If a conversation in a moving vehicle requires
you to take notes, pull off the road to a safe
location and stop your vehicle before doing
so.
CAUTION
● Keep the antenna as far away as possible
from the electronic control modules.
● Keep the antenna wire more than 8 in (20 cm)
away from the electronic control system har-
ness. Do not route the antenna wire next to
any harness.
● Adjust the antenna standing-wave ratio as
recommended by the manufacturer.
● Connect the ground wire from the CB radio
chassis to the body.
● For details, consult an INFINITI retailer.
CAR PHONE OR CB RADIO
Monitor, climate, audio, phone and voice recognition systems4-85
—
—
07/15/10—tbrooks


Activating Alternate Command Mode
When the Standard Mode is active, perform the
following steps to switch to the Alternate Com-
mand Mode.
1. Push the SETTING button on the instru-ment panel.
2. Highlight the “Others” key.
3. Highlight the “Voice Recognition” key. 4. Highlight the “Alternate Command Mode”
key.
5. The confirmation message is displayed on the screen. Push the “OK” key to activate
the Alternate Command Mode.Displaying command list
If you are controlling the system by voice
commands for the first time or do not know the
appropriate voice command, perform the fol-
lowing procedure for displaying the voice com-
mand list (available only in Alternate Command
Mode).
1. Push the INFO button on the instrumentpanel.
2. Select the “Others” key.
3. Select the “Voice Recognition” key.
4. Select the “Command List” key.
SAA2529SAA2543SAA2544
Monitor, climate, audio, phone and voice recognition systems4-123
—
—
07/15/10—tbrooks


Displaying user guide
You can confirm how to use voice commands by
accessing a simplified User Guide, which con-
tains basic instructions and tutorials for several
voice commands.
1. Push the INFO button on the instrumentpanel.
2. Select the “Others” key using the INFINITI controller and push the ENTER button.
3. Highlight the “Voice Recognition” key us- ing the INFINITI controller and push the
ENTER button. 4. Highlight the “User Guide” key using the
INFINITI controller and push the ENTER
button.
5. Highlight an item using the INFINITI con- troller and push the ENTER button.
Available items :
● Getting Started
Describe the basics of how to operate the
INFINITI Voice Recognition system.
● Let’s Practice
Mode that allows practicing by following the
instructions of the system voice.
● Using the Address Book
Refer to Navigation System Owner’s Manual.
● Finding a Street Address (if so equipped)
Refer to Navigation System Owner’s Manual.
● Placing Calls
Tutorial for making a phone call by voice
command operation.
● Help on Speaking
Displays useful tips for how to correctly
speak commands in order for them to be
properly recognized by the system. ●
Voice Recognition Settings
Describes the available voice recognition
settings.
● Adapting the System to Your Voice
Tutorial adapting the system to your voice.USING THE SYSTEM
Initialization
When the ignition switch is pushed to the ON
position, INFINITI Voice Recognition is initial-
ized, which takes a few seconds. When com-
pleted, the system is ready to accept voice
commands. If the TALK
switch is pushed
before the initialization completes the display
will show the message: “Phonetic data down-
loaded. Please wait.” or a beep sounds.
SAA2547
4-128Monitor, climate, audio, phone and voice recognition systems
—
—
07/15/10—tbrooks