component INFINITI M35 2007 Factory Service Manual

DI-26
COMBINATION METERS
Revision: 2007 April2007 M35/M45
Electrical Components InspectionNKS003UD
CHECK FUEL LEVEL SENSOR UNIT
For removal, refer to FL-4, "FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY" .
Check Fuel Level Sensor Unit and Fuel Pump (Main)
Check resistance between terminals 2 and 5.
*1 and *2: When float rod is in contact with stopper.

If the results of check are NG, check the fuel level sensor unit
and fuel pump (main) harness. Refer to DI-26, "
Check Fuel
Level Sensor Unit and Pump (Main) Harness" .
Check Fuel Level Sensor Unit and Pump (Main) Harness
Check continuity at following terminals.

If the results of check are NG, replace fuel pump assembly. If the
results of check are OK, replace fuel level sensor unit.
Check Fuel Level Sensor Unit (Sub)
Check resistance between terminals 1 and 2.
*1 and *2: When float rod is in contact with stopper.Terminal Float position [mm (in)] Resistance value [Ω]
25*1 Full 210 (8.27) Approx. 3
*2 Empty 30 (1.18) Approx. 80
SKIB3550J
Terminal Continuity
2 - Signal terminal (A)
Ye s
5 - Ground terminal (B)
SKIB3551J
Terminal Float position [mm (in)]Resistance
value [Ω]
12*1 Full 9 (0.35) Approx. 3
*2 Empty 179 (7.05) Approx. 43
SKIB2678J

DI-40
WARNING LAMPS
Revision: 2007 April2007 M35/M45
Component Parts and Harness Connector LocationNKS003UP
PKIB7653E

DI-54
WARNING LAMPS
Revision: 2007 April2007 M35/M45
4. CHECK OIL PRESSURE SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and
ground.
OK or NG
OK >> Replace IPDM E/R. Refer to PG-31, "Removal and
Installation of IPDM E/R" .
NG >> Repair harness or connector.
5. CHECK IPDM E/R (CONSULT-II)
Perform self-diagnosis of IPDM E/R. Refer to PG-20, "
CONSULT-II Function (IPDM E/R)" .
Self
-diagnostic results content
No malfunction detected>> Replace combination meter.
Malfunction detected>> Check applicable parts, and repair or replace corresponding parts.
Electrical Component InspectionNKS003UU
OIL PRESSURE SWITCH
Check continuity between oil pressure switch and ground.
IPDM E/R connector Terminal
GroundContinuity
E9 52 No
PKIB7659E
Condition
Oil pressure [kPa (kg/cm2 , psi)]Continuity
Engine stopped Less than 29 (0.3, 4) Yes
Engine running More than 29 (0.3, 4) No
ELF0044D

WARNING CHIME
DI-61
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: 2007 April2007 M35/M45
Component Parts and Harness Connector LocationNKS003UZ
PKIB7661E

DI-74
WARNING CHIME
Revision: 2007 April2007 M35/M45
4. CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE)
Check seat belt buckle switch (driver side). Refer to DI-74, "
SEAT BELT BUCKLE SWITCH (DRIVER SIDE)" .
OK or NG
OK >> Check seat belt buckle switch (driver side) ground circuit.
NG >> Replace seat belt buckle switch (driver side).
Electrical Component InspectionNKS003VC
FRONT DOOR SWITCH (DRIVER SIDE)
Check continuity between terminal 2 and door switch case ground.
SEAT BELT BUCKLE SWITCH (DRIVER SIDE)
Check continuity between terminals 1 and 2.
Terminal Condition Continuity
2Door switch
case groundWhen door switch is released. Yes
When door switch is pushed. No
PKIC0245E
Terminal Condition Continuity
12When seat belt is unfastened. Yes
When seat belt is fastened. No
PKIB7665E

LANE DEPARTURE WARNING SYSTEM
DI-77
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: 2007 April2007 M35/M45
System Diagram
Components Description
NOTE:
*: This indicates in a few seconds for the system check during ignition switch ON.
POWER SUPPLY AND GROUND CIRCUIT
With the ignition switch in the ON or START position, power is supplied

through 10A fuse [No. 12, located in the fuse block (J/B)]

to LDW camera unit terminal 1.
Ground is supplied

to LDW camera unit terminals 6 and 12

through grounds M16 and M70.
Action TestNKS003VH
LDW SYSTEM RUNNING TEST
WARNING:

Be careful when performing road test.

Understand “Precautions” and “System Description” well before the road test. Refer to DI-75,
"Precautions for Lane Departure Warning (LDW) system" and DI-75, "System Description" .
Function Check
Check the LDW system operation according to the condition that the warning function works. Refer to DI-75,
"LDW SYSTEM OPERATION" .
PKIC0698E
Component Description
LDW camera unitDetects the lane marker by the built-in camera, gives judgement for the warning according to the
result of detection and signals from each unit, and transmits the operation signal to LDW chime and
LDW indicator lamp.
LDW switch

Selects ON/OFF of the system.

Indicates ON/OFF of the signal with LDW system ON indicator.
LDW chime Gives a warning chime according to the direction from LDW camera unit.
LDW indicator lampInstalled in combination meter, and indicates the system condition.

Blinks when LDW system is functioning to alert the driver.

Stays on when LDW system is malfunctioning.*
BCM Transmits turn indicator signal to LDW camera unit with CAN communication signal.
ABS actuator and electric unit
(control unit)Transmits vehicle speed signal to LDW camera unit with CAN communication signal.
TCM Transmits vehicle speed signal to LDW camera unit with CAN communication signal. (For detecting
incorrect speed.)

LANE DEPARTURE WARNING SYSTEM
DI-85
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: 2007 April2007 M35/M45
Component Parts and Harness Connector LocationNKS003VJ
PKIB7670E

DI-100
LANE DEPARTURE WARNING SYSTEM
Revision: 2007 April2007 M35/M45
Turn Signal Input InspectionNKS003VY
1. CHECK TURN SIGNAL INPUT
Check turn signal input “TURN SIGNAL” in “DATA MONITOR” mode
with CONSULT-II.
OK or NG
OK >> Turn signal input is OK. Return to DI-93, "SYMPTOM
CHART" .
NG >> Check turn signal and hazard warning lamps system,
and repair or replace corresponding parts. Refer to LT- 2 2 1 , "
How to Perform Trouble Diagnoses" .
Electrical Component InspectionNKS003VZ
LDW SWITCH
Check continuity between terminals 6 and 7.
Removal and Installation for LDW Camera UnitNKS003W0
REMOVAL
1. Remove roof console. Refer to EI-52, "HEADLINING" .
2. Disconnect LDW camera unit connector (1).
3. Remove the bolts (A), and remove LDW camera unit (2).
INSTALLATION
Installation is the reverse order of removal.
CAUTION:

Remove the camera lens cap for replacement.

Never give an impact to the LDW camera unit.

Adjust the camera aiming every time the LDW camera unit is removed or installed. Refer to DI-78,
"Camera Aiming Adjustment" . “TURN SIGNAL”
When lighting switch is in TURN RH position : RH
When lighting switch is in TURN LH position : LH
When hazard switch is turned ON : RH/LH
SKIB3125E
Terminal Condition Continuity
67When LDW switch is pushed. Yes
When LDW switch is released. No
PKIC0258E
PKIB7673E

EC-1
ENGINE CONTROL SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION EC
A
EC
Revision: 2007 April2007 M35/M45
ENGINE CONTROL SYSTEM
VQ35DE
INDEX FOR DTC ...................................................... 16
DTC No. Index ....................................................... 16
Alphabetical Index .................................................. 20
PRECAUTIONS ........................................................ 24
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ................................................................ 24
Precautions for Procedures without Cowl Top Cover ... 24
On Board Diagnostic (OBD) System of Engine and
A/T .......................................................................... 24
Precaution .............................................................. 25
PREPARATION ......................................................... 28
Special Service Tools ............................................. 28
Commercial Service Tools ...................................... 29
ENGINE CONTROL SYSTEM .................................. 30
System Diagram ..................................................... 30
Multiport Fuel Injection (MFI) System .................... 31
Electronic Ignition (EI) System ............................... 33
Fuel Cut Control (At No Load and High Engine
Speed) .................................................................... 34
AIR CONDITIONING CUT CONTROL ..................... 35
Input/Output Signal Chart ....................................... 35
System Description ................................................ 35
AUTOMATIC SPEED CONTROL DEVICE (ASCD) ... 36
System Description ................................................ 36
Component Description .......................................... 37
CAN COMMUNICATION .......................................... 38
System Description ................................................ 38
EVAPORATIVE EMISSION SYSTEM ....................... 39
Description ............................................................. 39
Component Inspection ........................................... 42
Removal and Installation ........................................ 43
How to Detect Fuel Vapor Leakage ....................... 43
ON BOARD REFUELING VAPOR RECOVERY
(ORVR) ...................................................................... 46
System Description ................................................ 46
Diagnostic Procedure ............................................. 47
Component Inspection ........................................... 49POSITIVE CRANKCASE VENTILATION ................. 51
Description .............................................................. 51
Component Inspection ............................................ 51
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-
NATS) ........................................................................ 53
Description .............................................................. 53
ON BOARD DIAGNOSTIC (OBD) SYSTEM ............ 54
Introduction ............................................................. 54
Two Trip Detection Logic ........................................ 54
Emission-Related Diagnostic Information ............... 55
Malfunction Indicator Lamp (MIL) ........................... 70
OBD System Operation Chart ................................ 73
BASIC SERVICE PROCEDURE ............................... 78
Basic Inspection ..................................................... 78
Idle Speed and Ignition Timing Check .................... 83
Procedure After Replacing ECM ............................ 85
VIN Registration ..................................................... 85
Accelerator Pedal Released Position Learning ...... 86
Throttle Valve Closed Position Learning ................. 86
Idle Air Volume Learning ........................................ 86
Fuel Pressure Check .............................................. 88
TROUBLE DIAGNOSIS ............................................ 90
Trouble Diagnosis Introduction ............................... 90
DTC Inspection Priority Chart ................................. 96
Fail-Safe Chart ....................................................... 98
Symptom Matrix Chart ............................................ 99
Engine Control Component Parts Location ..........103
Vacuum Hose Drawing ..........................................111
Circuit Diagram .....................................................112
ECM Harness Connector Terminal Layout ...........114
ECM Terminals and Reference Value ...................114
CONSULT-II Function (ENGINE) ..........................123
Generic Scan Tool (GST) Function .......................135
CONSULT-II Reference Value in Data Monitor .....138
Major Sensor Reference Graph in Data Monitor
Mode .....................................................................141
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .143
Description ............................................................143
Testing Condition ..................................................143

EC-2Revision: 2007 April2007 M35/M45 Inspection Procedure ............................................143
Diagnostic Procedure ...........................................144
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT .......................................................................153
Description ............................................................153
Diagnostic Procedure ...........................................153
POWER SUPPLY AND GROUND CIRCUIT ...........154
Wiring Diagram .....................................................154
Diagnostic Procedure ...........................................155
Ground Inspection ................................................160
DTC U1000, U1001 CAN COMMUNICATION LINE .161
Description ............................................................161
On Board Diagnosis Logic ....................................161
DTC Confirmation Procedure ...............................161
Wiring Diagram .....................................................162
Diagnostic Procedure ...........................................163
DTC U1010 CAN COMMUNICATION .....................164
Description ............................................................164
On Board Diagnosis Logic ....................................164
DTC Confirmation Procedure ...............................164
Diagnostic Procedure ...........................................165
DTC P0011, P0021 IVT CONTROL ........................166
Description ............................................................166
CONSULT-II Reference Value in Data Monitor Mode
.166
On Board Diagnosis Logic ....................................167
DTC Confirmation Procedure ...............................167
Diagnostic Procedure ...........................................168
Component Inspection ..........................................169
Removal and Installation ......................................169
DTC P0031, P0032, P0051, P0052 A/F SENSOR 1
HEATER ..................................................................170
Description ............................................................170
CONSULT-II Reference Value in Data Monitor Mode
.170
On Board Diagnosis Logic ....................................170
DTC Confirmation Procedure ...............................170
Wiring Diagram .....................................................171
Diagnostic Procedure ...........................................174
Component Inspection ..........................................176
Removal and Installation ......................................176
DTC P0037, P0038, P0057, P0058 HO2S2 HEATER .177
Description ............................................................177
CONSULT-II Reference Value in Data Monitor Mode
.177
On Board Diagnosis Logic ....................................177
DTC Confirmation Procedure ...............................178
Wiring Diagram .....................................................179
Diagnostic Procedure ...........................................182
Component Inspection ..........................................184
Removal and Installation ......................................184
DTC P0075, P0081 IVT CONTROL SOLENOID
VALVE .....................................................................185
Component Description ........................................185
CONSULT-II Reference Value in Data Monitor Mode
.185
On Board Diagnosis Logic ....................................185
DTC Confirmation Procedure ...............................185
Wiring Diagram .....................................................186Diagnostic Procedure ............................................190
Component Inspection ..........................................192
Removal and Installation .......................................192
DTC P0101 MAF SENSOR .....................................193
Component Description ........................................193
CONSULT-II Reference Value in Data Monitor Mode
.193
On Board Diagnosis Logic ....................................193
DTC Confirmation Procedure ................................194
Overall Function Check .........................................195
Wiring Diagram .....................................................196
Diagnostic Procedure ............................................197
Component Inspection ..........................................200
Removal and Installation .......................................201
DTC P0102, P0103 MAF SENSOR .........................202
Component Description ........................................202
CONSULT-II Reference Value in Data Monitor Mode
.202
On Board Diagnosis Logic ....................................202
DTC Confirmation Procedure ................................203
Wiring Diagram .....................................................204
Diagnostic Procedure ............................................205
Component Inspection ..........................................207
Removal and Installation .......................................208
DTC P0112, P0113 IAT SENSOR ............................209
Component Description ........................................209
On Board Diagnosis Logic ....................................209
DTC Confirmation Procedure ................................209
Wiring Diagram .....................................................211
Diagnostic Procedure ............................................212
Component Inspection ..........................................213
Removal and Installation .......................................213
DTC P0117, P0118 ECT SENSOR ..........................214
Component Description ........................................214
On Board Diagnosis Logic ....................................214
DTC Confirmation Procedure ................................215
Wiring Diagram .....................................................216
Diagnostic Procedure ............................................217
Component Inspection ..........................................218
Removal and Installation .......................................218
DTC P0122, P0123 TP SENSOR ............................219
Component Description ........................................219
CONSULT-II Reference Value in Data Monitor Mode
.219
On Board Diagnosis Logic ....................................219
DTC Confirmation Procedure ................................220
Wiring Diagram .....................................................221
Diagnostic Procedure ............................................222
Component Inspection ..........................................225
Removal and Installation .......................................225
DTC P0125 ECT SENSOR ......................................226
Component Description ........................................226
On Board Diagnosis Logic ....................................226
DTC Confirmation Procedure ................................227
Diagnostic Procedure ............................................227
Component Inspection ..........................................228
Removal and Installation .......................................228
DTC P0127 IAT SENSOR ........................................229
Component Description ........................................229