fog light INFINITI M35 2007 Factory Owner's Manual

GW-82
REAR WINDOW DEFOGGER
Revision: 2007 April2007 M35/M45
Work FlowNIS0022P
1. Check the symptom and customer's requests.
2. Understand the outline of system. Refer to GW-71, "
System Description" .
3. According to the trouble diagnosis chart, repair or replace the cause of the malfunction. Refer to GW-82,
"Trouble Diagnoses Symptom Chart" .
4. Does rear window defogger operate normally? YES: GO TO 5, NO: GO TO 3.
5. INSPECTION END.
Trouble Diagnoses Symptom ChartNIS0022Q
Make sure other systems using the signal of the following systems operate normally.
*1: With navigation system
*2: Without navigation systemSymptom Diagnoses / Service procedure Refer to page
Rear window defogger and door mirror defogger do not
operate. 1. Check BCM power supply and ground circuit GW-83
2. Check IPDM E/R auto active test PG-23
3. Check rear window defogger switch circuit GW-84
4. Check rear window defogger power supply circuit GW-84
5. Replace IPDM E/ RPG-31
Rear window defogger does not operate but both of door
mirror defogger operate.1.Check rear window defogger circuit GW-86
2.Check filament GW-92
Both of door mirror defogger does not operated but rear
window defogger operates. Check door mirror defogger power supply circuit GW-87
Driver side door mirror defogger does not operate. Check driver side door mirror defogger circuit GW-89
Passenger side door mirror defogger does not operate. Check passenger side door mirror defogger circuit GW-90
Rear window defogger switch does not light, and rear win-
dow defogger is not displayed on the display.
But rear window defogger operates. Check rear window defogger signal AV- 2 4 9*1
AV- 1 0 8*2
Rear window defogger switch does not light, but rear win-
dow defogger operatesReplace multi-function switchATC-123

REAR WINDOW DEFOGGER
GW-93
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2007 April2007 M35/M45
REPAIRING PROCEDURE
1. Wipe broken heat wire and its surrounding area clean with a
cloth dampened in alcohol.
2. Apply a small amount of conductive silver composition to tip of
drawing pen.
Shake silver composition container before use.
3. Place ruler on glass along broken line. Deposit conductive silver
composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm (0.20 in)] of the break.
4. After repair has been completed, check repaired wire for conti-
nuity. This check should be conducted 10 minutes after silver
composition is deposited.
Do not touch repaired area while test is being conducted.
5. Apply a constant stream of hot air directly to the repaired area
for approximately 20 minutes with a heat gun. A minimum dis-
tance of 3 cm (1.2 in) should be kept between repaired area and
hot air outlet.
If a heat gun is not available, let the repaired area dry for 24
hours.
PIIA0215E
SEL012D
SEL013D

LAN-52
[CAN]
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
CAN Communication Signal ChartNKS004FV
Refer to LAN-15, "How to Use CAN Communication Signal Chart" for how to use CAN communication signal
chart.
TYPE 1/TYPE 2/TYPE 3/TYPE 4/TYPE 5/TYPE 6/TYPE 7
NOTE:
Refer to LAN-41, "
Abbreviation List" for the abbreviations of the connecting units.
T: Transmit R: Receive
Signals
ECM
AFS
*1
BCM
LANE
*2
TCM
AV
I-KEY
M&A
STRG
TPMS
RAS
*3
PSB
ADP
ABS
ICC
*4
IPDM-E
A/C compressor request signal TR
Accelerator pedal position signal T R R R
ASCD CRUISE lamp signal T R
ASCD OD cancel request signal T R
ASCD operation signal T R
ASCD SET lamp signal T R
Battery voltage signal T R
Closed throttle position signal T R R
Cooling fan speed request signal TR
Engine coolant temperature signal T R
Engine speed signal T R R R R R R
Engine status signal T R R R
Fuel consumption monitor signal T R R
ICC brake switch signal T R
ICC prohibition signal T R
ICC steering switch signal T R
Malfunctioning indicator lamp signal T R
Power generation command value signal TR
Stop lamp switch signalTR
RT
TR
Wide open throttle position signal T R
AFS OFF indicator signal T R
A/C switch signal R T
ACC signal T R R
Blower fan motor switch signal R T
Buzzer output signalTR
TR
RT
Day time running light request signal T R
Door lock/unlock status signal T R
Door switch signal T R R R R R
Door unlock signal T R
Front fog light request signal T R R
Front wiper request signal T R R
High beam request signal T R R

TROUBLE DIAGNOSIS
LAN-53
[CAN]
C
D
E
F
G
H
I
J
L
MA
B
LAN
Revision: 2007 April2007 M35/M45
Ignition switch ON signal T R R
Ignition switch signal T R R
Key ID signal T R
Key switch signal T R
Low beam request signal T R
Oil pressure switch signalTR
RT
Position light request signal T R R
Rear window defogger switch signal T R
Sleep wake up signal T R R R R
Theft warning horn request signal T R
Trunk switch signal T R R
Turn indicator signal T R R
A/T CHECK indicator lamp signal T R
A/T position indicator signal R T R R R
A/T self-diagnosis signal R T
Current gear position signal T R R
Manual mode indicator signal T R R
N range signal T R R
Output shaft revolution signal R R T R
P range signal T R R R R
R range signal T R R R
Turbine revolution signal R T R
A/C switch/indicator signalTR
RT
System setting signalTR R
RT T
Door lock/unlock trunk open request signal R T
Hazard and horn request signal R T
Key warning signal T R
Meter display signalTR
RT
Panic alarm request signal R T
Power window open request signal R T
A/C evaporator temperature signal R T
Distance to empty signal R T
Fuel level low warning signal R T
Fuel level sensor signal R T
Manual mode shift down signal R T
Manual mode shift up signal R T
Manual mode signal R T
Not manual mode signal R T
Parking brake switch signal R TSignals
ECM
AFS
*1
BCM
LANE
*2
TCM
AV
I-KEY
M&A
STRG
TPMS
RAS
*3
PSB
ADP
ABS
ICC
*4
IPDM-E

LAN-54
[CAN]
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45

*1: Models with adaptive front-lighting system

*2: Models with lane departure warning

*3: Models with rear active steer

*4: Models with ICC system Seat belt buckle switch signal R T
Target A/C evaporator temperature signal R T
Vehicle speed signalRRR RRRT RR R
RRRRR TR
Steering angle sensor signal R T R R
Tire pressure data signal R T
Tire pressure signalRR T
TR
RAS signalTR
A/T shift schedule change demand signal R T
ABS malfunction signalTR
ABS operation signal TR
ABS warning lamp signal R T
Brake pressure control signalTR
Brake warning lamp signal R T
Side G sensor signal R T
SLIP indicator lamp signal R T
TCS malfunction signalTR
TCS operation signal TR
VDC malfunction signalTR
VDC OFF indicator lamp signal R T
VDC OFF switch signalTR
VDC operation signalTR
Deceleration degree commandment value signalRT
ICC OD cancel request signal R T
ICC operation signal R T
ICC warning lamp signal R T
Front wiper stop position signal R T
High beam status signal RT
Hood switch signal R T
Low beam status signal R R T
Rear window defogger control signal R R T
Starter relay status signal R TSignals
ECM
AFS
*1
BCM
LANE
*2
TCM
AV
I-KEY
M&A
STRG
TPMS
RAS
*3
PSB
ADP
ABS
ICC
*4
IPDM-E

TROUBLE DIAGNOSIS
LAN-55
[CAN]
C
D
E
F
G
H
I
J
L
MA
B
LAN
Revision: 2007 April2007 M35/M45
TYPE 8/TYPE 9/TYPE 10/TYPE 11
NOTE:
Refer to LAN-41, "
Abbreviation List" for the abbreviations of the connecting units.
T: Transmit R: Receive
Signals
ECM
4WD
AFS
*1
BCM
LANE
*2
TCM
AV
I-KEY
M&A
STRG
TPMS
PSB
ADP
ABS
ICC
*3
IPDM-E
A/C compressor request signal TR
Accelerator pedal position signal T R R R R
ASCD CRUISE lamp signal T R
ASCD OD cancel request signal T R
ASCD operation signal T R
ASCD SET lamp signal T R
Battery voltage signal T R
Closed throttle position signal T R R
Cooling fan speed request signal TR
Engine coolant temperature signal T R
Engine speed signal T R R R R R R
Engine status signal T R R R
Fuel consumption monitor signal T R R
ICC brake switch signal T R
ICC prohibition signal T R
ICC steering switch signal T R
Malfunctioning indicator lamp signal T R
Power generation command value signal TR
Snow mode switch signalTRR
RT
Stop lamp switch signalTR
RRT
TR
Wide open throttle position signal T R
AWD signal T R
AWD warning lamp signal T R
AFS OFF indicator signal T R
A/C switch signal R T
ACC signal T R R
Blower fan motor switch signal R T
Buzzer output signalTR
TR
RT
Day time running light request signal T R
Door lock/unlock status signal T R
Door switch signal T R R R R R
Door unlock signal T R
Front fog light request signal T R R
Front wiper request signal T R R
High beam request signal T R R

LAN-56
[CAN]
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
Ignition switch ON signal T R R
Ignition switch signal T R R
Key ID signal T R
Key switch signal T R
Low beam request signal T R
Oil pressure switch signalTR
RT
Position light request signal T R R
Rear window defogger switch signal T R
Sleep wake up signal T R R R R
Theft warning horn request signal T R
Trunk switch signal T R R
Turn indicator signal T R R
A/T CHECK indicator lamp signal T R
A/T position indicator signal R T R R R
A/T self-diagnosis signal R T
Current gear position signal T R R
Manual mode indicator signal T R R
N range signal T R R
Output shaft revolution signal R R T R
P range signal T R R R R
R range signal T R R R
Turbine revolution signal R T R
A/C switch/indicator signalTR
RT
System setting signalTR R
RT T
Door lock/unlock trunk open request signal R T
Hazard and horn request signal R T
Key warning signalTR
Meter display signalTR
RT
Panic alarm request signal R T
Power window open request signal R T
A/C evaporator temperature signal R T
Distance to empty signal R T
Fuel level low warning signal R T
Fuel level sensor signal R T
Manual mode shift down signal R T
Manual mode shift up signal R T
Manual mode signal R T
Not manual mode signal R T
Parking brake switch signal R R TSignals
ECM
4WD
AFS
*1
BCM
LANE
*2
TCM
AV
I-KEY
M&A
STRG
TPMS
PSB
ADP
ABS
ICC
*3
IPDM-E

TROUBLE DIAGNOSIS
LAN-57
[CAN]
C
D
E
F
G
H
I
J
L
MA
B
LAN
Revision: 2007 April2007 M35/M45

*1: Models with adaptive front-lighting system

*2: Models with lane departure warning

*3: Models with ICC system Seat belt buckle switch signal R T
Target A/C evaporator temperature signal R T
Vehicle speed signalRRRRRRT RRR
RRRRR TR
Steering angle sensor signal R T R
Tire pressure data signal R T
Tire pressure signalRR T
TR
A/T shift schedule change demand signal R T
ABS malfunction signalTR
ABS operation signal TR
ABS warning lamp signal R T
Brake pressure control signalTR
Brake warning lamp signal R T
Side G sensor signal R T
SLIP indicator lamp signal R T
TCS malfunction signalTR
TCS operation signal TR
VDC malfunction signalTR
VDC OFF indicator lamp signal R T
VDC OFF switch signalTR
VDC operation signalTR
Deceleration degree commandment value signalRT
ICC OD cancel request signal R T
ICC operation signal R T
ICC warning lamp signalRT
Front wiper stop position signal R T
High beam status signal RT
Hood switch signal R T
Low beam status signal R R T
Rear window defogger control signal R R T
Starter relay status signal R TSignals
ECM
4WD
AFS
*1
BCM
LANE
*2
TCM
AV
I-KEY
M&A
STRG
TPMS
PSB
ADP
ABS
ICC
*3
IPDM-E

LT-3
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2007 April2007 M35/M45 System Description .............................................. 134
AFS (ADAPTIVE FRONT-LIGHTING SYSTEM) . 135
HEADLAMP AUTO AIMING .............................. 136
OUTLINE ........................................................... 136
AFS OPERATION ............................................. 137
HEADLAMP AUTO AIMING OPERATION ........ 139
CAN COMMUNICATION SYSTEM DESCRIP-
TION .................................................................. 139
CAN COMMUNICATION UNIT ......................... 139
Component Parts Description .............................. 140
AFS CONTROL UNIT ....................................... 140
SWIVEL ACTUATOR ........................................ 140
AIMING MOTOR ............................................... 140
AFS SWITCH .................................................... 141
HEIGHT SENSOR ............................................ 141
STEERING ANGLE SENSOR .......................... 141
IPDM E/R .......................................................... 141
ECM .................................................................. 141
TCM .................................................................. 141
UNIFIED METER AND A/C AMP. ..................... 141
COMBINATION METER ................................... 141
Schematic ............................................................ 142
Wiring Diagram — AFS — ................................... 143
Terminals and Reference Values for AFS Control
Unit ....................................................................... 149
How to Proceed with Trouble Diagnosis .............. 151
Preliminary Check ................................................ 151
CONSULT-II Function (ADAPTIVE LIGHT) .......... 152
CONSULT-II BASIC OPERATION ..................... 152
WORK SUPPORT (STEERING ANGLE SEN-
SOR ADJUSTMENT) ........................................ 152
WORK SUPPORT (LEVELIZER ADJUSTMENT)
. 152
SELF-DIAG RESULTS ...................................... 153
DATA MONITOR ............................................... 157
ACTIVE TEST ................................................... 159
Symptom Chart .................................................... 160
DTC B2503 SWIVEL ACTUATOR RH ................. 161
DTC B2504 SWIVEL ACTUATOR LH .................. 168
DTC B2514 HI SEN UNUSUAL RR ..................... 175
DTC B2521 ECU CIRC ........................................ 179
AFS Operation Check (Function Test) ................. 182
Auto Aiming Operation Check (Function Test) ..... 184
AFS Switch Does Not Operate ............................. 186
Auto Aiming Does Not Operate (Check Aiming
Motor System Circuit) ........................................... 188
AFS OFF Indicator Does Not Operate ................. 191
Removal and Installation of Steering Angle Sensor . 191
Removal and Installation of Front Combination
Lamp .................................................................... 191
Removal and Installation of AFS Control Unit ...... 192
REMOVAL ......................................................... 192
INSTALLATION ................................................. 192
Removal and Installation of AFS Switch .............. 192
REMOVAL ......................................................... 192
INSTALLATION ................................................. 192
Removal and Installation of Height Sensor .......... 193
REMOVAL ......................................................... 193
INSTALLATION ................................................. 193FRONT FOG LAMP ................................................194
Component Parts and Harness Connector Location .194
System Description ...............................................194
OUTLINE ...........................................................195
COMBINATION SWITCH READING FUNCTION .196
EXTERIOR LAMP BATTERY SAVER CONTROL .196
CAN Communication System Description ............196
CAN Communication Unit .....................................196
Schematic .............................................................197
Wiring Diagram — F/FOG — ................................198
Terminals and Reference Values for BCM ............202
Terminals and Reference Values for IPDM E/R ....203
How to Perform Trouble Diagnoses .....................203
Preliminary Check ................................................203
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ..................................................................203
CONSULT-II Functions (BCM) ..............................204
CONSULT-II Functions (IPDM E/R) ......................204
Front Fog Lamps Do Not Illuminate (Both Sides) . 205
Front Fog Lamp Does Not Illuminate (One Side) . 208
Front Fog Lamps Do Not Turn OFF ......................209
Aiming Adjustment ................................................210
Bulb Replacement ................................................211
Removal and Installation ......................................211
REMOVAL .........................................................211
INSTALLATION .................................................211
TURN SIGNAL AND HAZARD WARNING LAMPS .212
Component Parts and Harness Connector Location .212
System Description ...............................................212
TURN SIGNAL OPERATION ............................212
HAZARD LAMP OPERATION ...........................213
COMBINATION SWITCH READING FUNCTION .214
CAN Communication System Description ............214
CAN Communication Unit .....................................214
Schematic .............................................................215
Wiring Diagram — TURN — .................................216
Terminals and Reference Values for BCM ............220
How to Perform Trouble Diagnoses .....................221
Preliminary Check ................................................222
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ..................................................................222
CONSULT-II Functions (BCM) ..............................223
CONSULT-II BASIC OPERATION .....................223
DATA MONITOR ...............................................223
ACTIVE TEST ...................................................223
Turn Signal Lamp Does Not Operate ...................224
Hazard Warning Lamp Does Not Operate But Turn
Signal Lamp Operate ............................................226
Turn Signal Indicator Lamp Does Not Operate ....227
Bulb Replacement/Removal and Installation of Side
Turn Signal Lamp .................................................229
REMOVAL .........................................................229
INSTALLATION .................................................229
Bulb Replacement (Front Turn Signal Lamp) .......229
Bulb Replacement (Rear Turn Signal Lamp) ........229
Removal and Installation of Front Turn Signal Lamp .229
Removal and Installation of Rear Turn Signal Lamp .229
LIGHTING AND TURN SIGNAL SWITCH ..............230
Removal and Installation ......................................230

LT-24
HEADLAMP (FOR USA) - CONVENTIONAL TYPE -
Revision: 2007 April2007 M35/M45
NOTE:
This item is displayed, but cannot be monitored.
ACTIVE TEST
Operation Procedure
1. Touch “HEAD LAMP” on “SELECT TEST ITEM” screen.
2. Touch “ACTIVE TEST” on “SELECT DIAG MODE” screen.
3. Touch item to be tested and check operation of the selected item.
4. During the operation check, touching “BACK” deactivates the operation.
Display Item List
NOTE:
This item is displayed, but cannot be tested.HEAD LAMP SW 1 “ON/OFF”Displays status (headlamp switch 1: ON/others: OFF) of headlamp switch 1 judged from light-
ing switch signal.
HEAD LAMP SW 2 “ON/OFF”Displays status (headlamp switch 2: ON/others: OFF) of headlamp switch 2 judged from light-
ing switch signal.
TAIL LAMP SW “ON/OFF”Displays status (lighting switch 1ST or 2ND position: ON/others: OFF) of lighting switch judged
from lighting switch signal.
AUTO LIGHT SW “ON/OFF”Displays status of the lighting switch as judged from the lighting switch signal. (AUTO position:
ON/other than AUTO position: OFF)
PASSING SW “ON/OFF”Displays status (flash-to-passing switch: ON/others: OFF) of flash-to-passing switch judged
from lighting switch signal.
FR FOG SW “ON/OFF”Displays status (front fog lamp switch: ON/others: OFF) of front fog lamp switch judged from
lighting switch signal.
DOOR SW - DR “ON/OFF”Displays status of the driver door as judged from the driver door switch signal. (door is open:
ON/door is closed: OFF)
DOOR SW - AS “ON/OFF”Displays status of the passenger door as judged from the passenger door switch signal. (door
is open: ON/door is closed: OFF)
DOOR SW - RR “ON/OFF”Displays status of the rear door as judged from the rear door switch (RH) signal. (door is open:
ON/door is closed: OFF)
DOOR SW - RL “ON/OFF”Displays status of the rear door as judged from the rear door switch (LH) signal. (door is open:
ON/door is closed: OFF)
BACK DOOR SW
NOTE “OFF” —
I - KEY LOCK “ON/OFF” Displays “locked (ON)/other (OFF)” status, determined from lock signal.
OPTICAL SENSOR “0 - 5V” Displays “outside brightness (close to 5 V when light/close to 0 V when dark)” judged from
optical sensor signal.
VEHICLE SPEED “km/h” Displays vehicle speed as judged from vehicle speed signal.Monitor item Contents
Test item Description
TAIL LAMP Allows tail lamp relay to operate by switching ON-OFF.
FR FOG LAMP Allows front fog lamp relay to operate by switching ON-OFF.
DAYTIME RUNNING LIGHT
NOTE—
HEAD LAMP (HI, LO) Allows headlamp relay to operate by switching ON-OFF.