INFINITI M35 2007 Factory Service Manual
Page 4641 of 4647
WW-50
CIGARETTE LIGHTER
Revision: 2007 April2007 M35/M45
CIGARETTE LIGHTERPFP:35330
Wiring Diagram — CIGAR —NKS003X9
TKWT3219E
Page 4642 of 4647
CIGARETTE LIGHTER
WW-51
C
D
E
F
G
H
I
J
L
MA
B
WW
Revision: 2007 April2007 M35/M45
Removal and InstallationNKS003XA
REMOVAL
1. Remove A/T console finisher. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove screws (A) from reverse side cigarette lighter socket.
3. Pull out cigarette lighter (1).
4. Insert a small screwdriver or similar tool between the cigarette
lighter socket (2) and cigarette lighter ring (3). Pull out cigarette
lighter socket (2).
INSTALLATION
Note the following, and installation is the reverse order of removal.
CAUTION:
Align notches of cigarette lighter ring and cigarette lighter socket when installing.
SKIB4207E
SKIB4262E
Page 4643 of 4647
WW-52
POWER SOCKET
Revision: 2007 April2007 M35/M45
POWER SOCKETPFP:253A2
Wiring Diagram — P/SCKT —NKS003XB
TKWT3220E
Page 4644 of 4647
POWER SOCKET
WW-53
C
D
E
F
G
H
I
J
L
MA
B
WW
Revision: 2007 April2007 M35/M45
Removal and Installation of Center Console Box Power SocketNKS003XC
REMOVAL
1. Remove console box. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove inner socket (1) from the ring (2) while pressing the
hook (B) on the ring out from square hole (A).
3. Remove ring from console box while pressing pawls.
INSTALLATION
Note the following, and installation is the reverse order of removal.
CAUTION:
Align notches of inner socket and ring, and console box when installing.
Removal and Installation of Center Console Box Rear Side Power SocketNKS003XD
REMOVAL
1. Remove the console rear finisher. Refer to IP-19, "CENTER CONSOLE ASSEMBLY" .
2. Remove inner socket (1) and ring (2) from the console rear fin-
isher while pressing the hook on ring from square hole.
INSTALLATION
Note the following, and installation is the reverse order of removal.
CAUTION:
Align notches of inner socket and ring, and console box when installing.
SKIB4263E
SKIB4265E
Page 4645 of 4647
WW-54
HORN
Revision: 2007 April2007 M35/M45
HORNPFP:25610
Wiring Diagram — HORN —NKS003XE
TKWT3221E
Page 4646 of 4647
HORN
WW-55
C
D
E
F
G
H
I
J
L
MA
B
WW
Revision: 2007 April2007 M35/M45
Removal and InstallationNKS003XF
REMOVAL
1. Remove front grille. Refer to EI-16, "FRONT GRILLE" .
2. Disconnect horn (HI) connectors.
3. Remove horn (HI) mounting bolt (A), and remove horn (HI) (1)
from vehicle.
4. Remove fender protector (front) LH to obtain work space between the fender protector and fender.
5. Disconnect horn (LO) connectors.
6. Remove horn (LO) mounting bolts (A), and remove horn (LO) (1)
from vehicle.
INSTALLATION
Tighten horn bolt to specified torque.
SKIB4266E
SKIB4267E
Horn mounting bolt :17.1 N·m (1.7 kg-m, 13 ft-lb.)
Page 4647 of 4647
WW-56
HORN
Revision: 2007 April2007 M35/M45