weight INFINITI QX30 2017 User Guide

MessagePossible causes/consequences and solutions
[Front Passenger Airbag
Disabled See Operator’s
Manual] The front-passenger front air bag is disabled during the journey although an adult or person of corresponding stature is on the front
passenger seat.
Front passenger seat adult occupants who are properly seated and using the seat belt as outlined in this manual should not cause the
front passenger air bag to be automatically turned OFF. For small adults it may be turned OFF, however if the occupant takes his/her
weight off the seat cushion (for example, by not sitting upright, by sitting on an edge of the seat, or by otherwise being out of position),
this could cause the sensor to turn the air bag OFF. Always be sure to be seated and wearing the seat belt properly for the most effective
protection by the seat belt and supplemental air bag.
If additional forces are applied to the seat, the system may interpret the occupant’s weight as lower than it actually is.
1. Stop the vehicle in a safe area away from traffic as soon as possible, paying attention to road and traffic conditions.
2. Secure the vehicle against rolling away.
3. Switch the ignition off.
4. Have the occupant on the front-passenger seat step out of the vehicle.
5. Make sure that the seat is unoccupied, close the front passenger door and switch on the ignition.
6. Observe the <PASSENGER AIR BAG> indicator lights in the center console and the vehicle information display and check the following.
Seat unoccupied and ignition switched on:
- The <PASSENGER AIR BAG OFF> and <PASSENGER AIR BAG ON> indicator lights must light up simultaneously for approximately six
seconds.
- The <PASSENGER AIR BAG OFF> indicator lights must then light up and remain lit. If the indicator light is on, the automatic
front-passenger front air bag deactivation system has disabled the front-passenger front air bag (see Front passenger air bag and
status light in the1. Safety — seats, seat belts and supplemental restraint system section)
- the [Front Passenger Airbag Enabled See Operator’s Manual] or [Front Passenger Airbag Disabled See Operator’s Manual] display
messages must not be shown in the vehicle information display.
7. Wait for a period of at least 60 seconds until the necessary system checks have been completed.
8. Make sure that the display messages do not appear in the vehicle information display.
If these conditions are met, the front-passenger seat can be occupied again. Whether the <PASSENGER AIR BAG OFF> or <ON> indicator
light remains lit or goes out depends on how the automatic front passenger front air bag deactivation system classifies the occupant.
If the conditions are not met, the system is not operating correctly.
Have the system checked immediately. It is recommended you visit an INFINITI retailer for this service.
For further information on the automatic front-passenger front air bag deactivation feature (see Front passenger air bag and status light
in the 1. Safety — seats, seat belts and supplemental restraint system section).
2-38Instruments and controls

MessagePossible causes/consequences and solutions
[Front Passenger Airbag
Enabled See Operator’s
Manual] The front-passenger front air bag is enabled during the journey although:
•A child or child restraint as specified in U.S. regulations is located on the front-passenger seat.
or
•The front-passenger seat is not occupied.
The system may detect objects or forces that are adding to the weight applied to the seat.
1. Stop the vehicle in a safe area away from traffic as soon as possible, paying attention to road and traffic conditions.
2. Secure the vehicle against rolling away.
3. Switch the ignition off.
4. Open the front-passenger door.
5. Remove the child and the child restraint system from the front passenger seat.
6. Make sure there are no objects applying additional force to the seat. The system may otherwise detect the additional force and interpret the seat occupant’s weight as greater than it actually is.
7. Make sure that the seat is unoccupied, close the front passenger door and switch on the ignition.
8. Observe the <PASSENGER AIR BAG> indicator lights in the center console and the vehicle information display and check the following. Seat unoccupied and ignition switched on:
- The <PASSENGER AIR BAG OFF> and <PASSENGER AIR BAG ON> indicator lights must light up simultaneously for approximately six
seconds.
- The <PASSENGER AIR BAG OFF> indicator light must then light up and remain lit. If the indicator light is on, the automatic
front-passenger front air bag deactivation system has disabled the front-passenger front air bag (see Front passenger air bag and
status light in the1. Safety — seats, seat belts and supplemental restraint system section).
- the [Front Passenger Airbag Enabled See Operator’s Manual] or [Front Passenger Airbag Disabled See Operator’s Manual] display
messages must not be shown in the vehicle information display.
7. Wait for a period of at least 60 seconds until the necessary system checks have been completed.
8. Make sure that the display messages do not appear in the vehicle information display.
If these conditions are met, the front-passenger seat can be occupied again. Whether the <PASSENGER AIR BAG OFF> or <ON> indicator
light remains lit or goes out depends on how the automatic front passenger front air bag deactivation system classifies the occupant.
If the conditions are not met, the system is not operating correctly.
Have the system checked immediately. It is recommended you visit an INFINITI retailer for this service.
For further information on the automatic front-passenger front air bag deactivation feature (see Front passenger air bag and status light
in the 1. Safety — seats, seat belts and supplemental restraint system section).
Instruments and controls2-39

•Properly secure cargo and do not allow it to
contact the top tether strap when it is at-
tached to the top tether anchor. Cargo that
is not properly secured or cargo that con-
tacts the top tether strap may damage the
top tether strap during a collision. If the
cargo cover contacts the top tether strap
when it is attached to the top tether anchor,
remove the cargo cover from the vehicle or
secure it on the cargo floor below its attach-
ment location. If the cargo cover is not re-
moved, it may damage the top tether strap
during a collision. Your child could be seri-
ously injured or killed in a collision if the
child restraint top tether strap is damaged.
•Do not use the cargo cover if the rear seats
are folded down.
Removal
1. Open the lift gate (seeLift gate lockin the
2. Instruments and controls section).
2. Detach both of the cords (left and right)
1from the inside of the lift gate.
3. Detach the parcel shelf
2by simply pulling
it rearwards through the lift gate opening.
CAUTION
Make sure the parcel shelf is carefully stored
when not in use in order to prevent any
damage.
Installation
1. Open the lift gate.
2. Insert the parcel shelf by pushing it forwards as far as possible through the lift gate
opening.
3. Attach the corresponding cords to each side
1of the lift gate.
4. Close the lift gate (see Lift gate lockin the
2. Instruments and controls section).
ROOF RACK (IF EQUIPPED)
Genuine NISSAN accessory cross bars are avail-
able through an INFINITI retailer. It is recom-
mended you visit an INFINITI retailer for cross-
bar or other equipment information.
Always distribute the luggage evenly on the roof
rack. Observe the maximum load limit shown on
the crossbars or roof carriers when you attach
them on the roof rails. It is recommended you
visit an INFINITI retailer for cross bar or other
equipment information.
Do not apply any load directly to the roof side
rails. Cross bars (if so equipped) must be
installed before applying load/cargo/luggage
to the roof of the vehicle.
Be careful that your vehicle does not exceed the
Gross Vehicle Weight Rating (GVWR) or its Gross
Axle Weight Rating (GAWR front and rear). The
GVWR and GAWR are located on the F.M.V.S.S.
or C.V. M.S.S. certification label (located on the
driver’s door pillar). For additional information,
refer toVehicle loading information in the10.
Technical information section.
NIC2672
Instruments and controls2-83

WARNING
•Drive extra carefully when the vehicle is
loaded at or near the cargo carrying capac-
ity, especially if the significant portion of
that load is carried on the roof rack.
•Heavy loading of the roof rack has the po-
tential to affect the vehicle stability and
handling during sudden or unusual han-
dling maneuvers.
•Roof rack load should be evenly distributed.
•Do not exceed maximum roof rack load
weight capacity.
•Properly secure all cargo with ropes or
straps to help prevent it from sliding or
shifting. In a sudden stop or collision, unse-
cured cargo could cause personal injury.
CAUTION
Always install the cross bars (if so equipped)
onto the roof side rails before loading cargo of
any kind. Loading cargo directly onto the roof
side rails or the vehicle’s roof may cause ve-
hicle damage.
SKI HATCH (IF EQUIPPED)
To open the ski hatch:
1. Fold down rear seat armrest.
2. Pull the center head restraint on the rearbench seat into the uppermost position.
3. Slide locking mechanism
1in the direction
of the arrow
4. Swing flap
2fully to the side. The flap is
held open by a magnet.
To close the ski hatch:
1. Swing flap
1in the luggage compartment
back until it engages.
2. Fold armrest fully up if necessary.
COMPARTMENT UNDER TRUNK FLOOR
Lift the trunk floor to access the underfloor
storage area.
NIC2668NIC2673
2-84Instruments and controls

8. Press on housing cover1and turn it to the
right.
9. Reconnect the negative (—) battery cable and close the hood. If you have a flat tire, refer to
Flat tirein the6.
In case of emergency section.
TIRE PRESSURE
Tire Pressure Monitoring System
(TPMS)
The Tire Pressure Monitoring System (TPMS)
monitors tire pressure of all tires. When the low
tire pressure warning light is lit, one or more of
the tires is significantly under-inflated.
The TPMS will activate only when the vehicle is
driven at speeds above 16 MPH (25 km/h). Also,
this system may not detect a sudden drop in tire
pressure (for example a flat tire while driving).
For additional information, refer to Tire Pres-
sure Monitoring System (TPMS) in the
5. Starting and driving section.
Tire inflation pressure
Check the tire pressures (including the spare)
often and always prior to long distance trips.
The recommended tire pressure specifications
are shown on the F.M.V.S.S./C.M.V.S.S. label or
the Tire and Loading Information label (if so
equipped) under the Cold Tire Pressure head-
ing. The Tire and Loading Information label is
affixed to the driver side center pillar. Tire pressures should be checked regularly be-
cause:
•Most tires naturally lose air over time.
•Tires can lose air suddenly when driven over
potholes or other objects or if the vehicle
strikes a curb while parking.
The tire pressures should be checked when the
tires are cold. The tires are considered COLD
after the vehicle has been parked for 3 or more
hours, or driven less than 1 mile (1.6 km) at
moderate speeds.
WARNING
•Improperly inflated tires can fail suddenly
and cause an accident.
•The Gross Vehicle Weight rating (GVWR) is
located on the F.M.V.S. S./C.M.V.S.S. certi-
fication label. The vehicle weight capacity is
indicated on the Tire and Loading Informa-
tion label (if so equipped). Do not load your
vehicle beyond this capacity. Overloading
your vehicle may result in reduced tire life,
unsafe operating conditions due to prema-
ture tire failure, or unfavorable handling
characteristics and could also lead to a se-
rious accident. Loading beyond the speci-
fied capacity may also result in failure of
other vehicle components.
WHEELS AND TIRES
8-26Do-it-yourself

1Tire size (example: P215/60R16 94H)
1 P: The “P” indicates the tire is designed for passenger vehicles. (Not all tires have this
information.)
2 Three-digit number (215): This number gives the width in millimeters of the tire from
sidewall edge to sidewall edge.
3 Two-digit number (60): This number, known as the aspect ratio, gives the tire’s ratio of
height to width.
4 R: The “R” stands for radial.
5 Two-digit number (16): This number is the wheel or rim diameter in inches.
6 Two- or three-digit number (94): This number is the tire’s load index. It is a measurement of
how much weight each tire can support. You
may not find this information on all tires
because it is not required by law. 7 H: Tire speed rating. You should not drive the
vehicle faster than the tire speed rating.
2TIN (Tire Identification Number) for a new
tire (example: DOT XX XX XXX XXXX)
1 DOT: Abbreviation for the “Department of Transportation”. The symbol can be placed
above, below or to the left or right of the Tire
Identification Number.
2 Two-digit code: Manufacturer’s identification mark
3 Two-digit code: Tire size
4 Three-digit code: Tire type code (Optional)
5 Four numbers represent the week and year the tire was built. For example, the numbers
3103 means the 31st week of 2003. If these
numbers are missing, then look on the other
sidewall of the tire.
3Tire ply composition and material
The number of layers or plies of rubber-
coated fabric in the tire. Tire manufacturers
also must indicate the materials in the tire,
which include steel, nylon, polyester, and
others.
4Maximum permissible inflation pressure
This number is the greatest amount of air
pressure that should be put in the tire. Do
not exceed the maximum permissible infla-
tion pressure.
5Maximum load rating
This number indicates the maximum load in
kilograms and pounds that can be carried
by the tire. When replacing the tires on the
vehicle, always use a tire that has the same
load rating as the factory installed tire.
6Term of “tubeless” or “tube type”
Indicates whether the tire requires an inner
tube (“tube type”) or not (“tubeless”).
7The word “radial”
The word “radial” is shown, if the tire has
radial structure.
8Manufacturer or brand name”
Manufacturer or brand name is shown.
SDI1606ZExampleNDI1623Example
Do-it-yourself8-29

10 Technical information
Recommended fluids/lubricants and capacities . . . .10-2Fuel recommendation ..................10-3
Engine oil and oil filter recommendations ......10-5
Air conditioner system refrigerant and oil
recommendations ................... .10-6
Engine specifications ................... .10-7
Wheels and Tires ..................... .10-8
Dimensions ..........................10-8
When traveling or registering in another country . . .10-9
Vehicle identification ................... .10-9
Vehicle identification number (VIN) plate ......10-9
Vehicle identification number (chassis number) .10-10
Engine serial number .................10-10
F.M.V.S.S./C.M.V.S.S. Certification label ......10-10
Emission control information label ..........10-11
Tire and loading information label ..........10-11
Air conditioner specification label ..........10-11Installing front license plate
...............10-12
Vehicle loading information ................10-13
TERMS ..........................10-13
Vehicle load capacity .................10-14
Loading tips ...................... .10-15
Measurement of weights ...............10-15
Trailer towing ....................... .10-15
Uniform tire quality grading ...............10-16
Treadwear ....................... .10-16
Traction AA, A, B and C ................10-16
Temperature A, B and C ................10-16
Emission control system warranty ............10-17
Reporting safety defects ..................10-17
Readiness for inspection/maintenance (I/M) test . . .10-18
Event data recorders (EDR) (if so equipped) ......10-19
Owner’s manual/service manual order information . .10-19

WARNING
•It is extremely dangerous to ride in a cargo
area inside a vehicle. In a collision, people
riding in these areas are more likely to be
seriously injured or killed.
•Do not allow people to ride in any area of
vehicle that is not equipped with seats and
seat belts.
•Be sure everyone in your vehicle is in a seat
and using a seat belt properly.
TERMS
It is important to familiarize yourself with the
following terms before loading your vehicle:
•Curb Weight (actual weight of your vehicle) -
vehicle weight including: standard and op-
tional equipment, fluids, emergency tools,
and spare tire assembly. This weight does
not include passengers and cargo.
•GVW (Gross Vehicle Weight) - curb weight
plus the combined weight of passengers and
cargo.
•GVWR (Gross Vehicle Weight Rating) - maxi-
mum total combined weight of the unloaded
vehicle, passengers, luggage, hitch, trailer
tongue load and any other optional equip-
ment. This information is located on the
F.M.V.S.S./C.M.V.S.S. label.
•GAWR (Gross Axle Weight Rating) - maximum
weight (load) limit specified for the front or
rear axle. This information is located on the
F.M.V.S.S./C.M.V.S.S. label.
•GCWR (Gross Combined Weight Rating) - The
maximum total weight rating of the vehicle,
passengers, cargo, and trailer.
•Vehicle Capacity Weight, Load limit, Total
load capacity - maximum total weight limit
specified of the load (passengers and cargo)
for the vehicle. This is the maximum com-
bined weight of occupants and cargo that
can be loaded into the vehicle. If the vehicle
is used to tow a trailer, the trailer tongue
weight must be included as part of the cargo
load. This information is located on the Tire
and Loading Information label.
•Cargo capacity - permissible weight of cargo,
the weight of total occupants weight sub-
tracted from the load limit.
VEHICLE LOADING INFORMATION
Technical information10-13

VEHICLE LOAD CAPACITY
Do not exceed the load limit of your vehicle
shown as “The combined weight of occupants
and cargo” on the Tire and Loading Information
label. Do not exceed the number of occupantsshown as “Seating Capacity” on the Tire and
Loading Information label.
To get “the combined weight of occupants and
cargo”, add the weight of all occupants, then
add the total luggage weight. Examples are
shown in the illustration.
Steps for determining correct load
limit
1. Locate the statement “The combined weight
of occupants and cargo should never exceed
XXX kg or XXX lbs” on your vehicle’s placard.
2. Determine the combined weight of the driver and passengers that will be riding in your
vehicle.
3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs.
4. The resulting figure equals the available amount of cargo and luggage load capacity.
For example, if the XXX amount equals 1400
lbs. and there will be five 150 lb. passengers
in your vehicle, the amount of available
cargo and luggage load capacity is 650 lbs.
(1400 750 (5 x 150) = 650 lbs) or 640 
340 (5 x 70) = 300 kg.)
5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That
weight may not safely exceed the available
cargo and luggage load capacity calculated
in Step 4.
STI0445
10-14Technical information

6. If your vehicle will be towing a trailer, loadfrom your trailer will be transferred to your
vehicle. Consult this manual to determine
how this reduces the available cargo and
luggage load capacity of your vehicle.
Before driving a loaded vehicle, confirm that
you do not exceed the Gross Vehicle Weight
Rating (GVWR) or the Gross Axle Weight Rating
(GAWR) for your vehicle. (See Measurement of
weights later in this section.)
Also check tires for proper inflation pressures.
See the Tire and Loading Information label.
LOADING TIPS
•The GVW must not exceed GVWR or GAWR as
specified on the F.M.V. S.S./C.M.V.S.S. cer-
tification label.
•Do not load the front and rear axle to the
GAWR. Doing so will exceed the GVWR.
WARNING
•Properly secure all cargo to help prevent it
from sliding or shifting. Do not place cargo
higher than the seatbacks. In a sudden stop
or collision, unsecured cargo could cause
personal injury.
•Do not load your vehicle any heavier than
the GVWR or the maximum front and rear
GAWRs. If you do, parts of your vehicle can
break, tire damage could occur, or it can
change the way your vehicle handles. This
could result in loss of control and cause
personal injury.
•Overloading could not only shorten the life
of your vehicle and the tires, but also could
cause unsafe vehicle handling and longer
braking distances. This may cause a prema-
ture tire failure which could result in a seri-
ous accident and personal injury. Failures
caused by overloading are not covered by
the vehicle’s warranty.
MEASUREMENT OF WEIGHTS
Secure loose items to prevent weight shifts that
could affect the balance of your vehicle. When
the vehicle is loaded, drive to a scale and weigh
the front and the rear wheels separately to
determine axle loads. Individual axle loads
should not exceed either of the gross axle
weight ratings (GAWR). The total of the axle
loads should not exceed the gross vehicle
weight rating (GVWR). These ratings are given
on the vehicle certification label. If weight rat- ings are exceeded, move or remove items to
bring all weights below the ratings.
Your vehicle was designed to be used to carry
passengers and luggage
CAUTION
Do not tow a trailer with your vehicle.
TRAILER TOWING
Technical information10-15