sensor INFINITI QX30 2017 Workshop Manual

SYSTEM TEMPORARILY UNAVAILABLE
When the radar sensor area is covered with dirt
or is obstructed, the system will automatically
be canceled. If the radar sensor area is covered
with ice, a transparent or translucent vinyl bag,
etc., the ICC system may not detect them. In
these instances, the ICC system may not cancel
and may not be able to maintain the selected
following distance from the vehicle ahead.
If the ICC system stops working due to a
malfunction or some other reason, one of the
following messages will be displayed in the
vehicle information display
2.
•[ICC off]
•[ICC Now Available]
•[ICC Currently Unavailable See Operator’s
Manual]
•[ICC Inoperative]
•[ICC Suspended]
•[ICC–––MPH]
[ICC off]: The ICC system has been deactivated.
If it was not deactivated by the driver, a warning
tone also sounds. [ICC Now Available]:
The ICC system is opera-
tional again after having been temporarily un-
available. You can now reactivate the ICC sys-
tem.
[ICC Currently Unavailable See Operator’s
Manual]: The ICC system is temporarily inopera-
tive. Possible causes:
•The function is impaired due to heavy rain or
snow.
•The radar sensor system is temporarily inop-
erative, e. g. due to electromagnetic radia-
tion emitted by nearby TV or radio stations or
other sources of electromagnetic radiation.
•The system is outside the operating tempera-
ture range.
•The on-board voltage is too low.
A warning tone also sounds.
Once the causes listed above no longer apply,
the display message goes out.
If the display message does not disappear:
•Pull over and stop the vehicle safely as soon
as possible, paying attention to road and
traffic conditions.
•Secure the vehicle against rolling away.
•Restart the engine. [ICC Inoperative]:
The ICC system is malfunc-
tioning. The adaptive brake assist function may
also have failed. A warning tone also sounds.
Have the system checked. It is recommended
you visit an INFINITI retailer for this service.
[ICC Suspended]: You have depressed the accel-
erator pedal. The ICC system is no longer
controlling the speed of the vehicle.
The display message should disappear when
you remove your foot from the accelerator pedal
[ICC–––MPH]: An activation condition for the
ICC system is not fulfilled.
Check the activation conditions for the ICC
system.
Starting and driving5-59

SYSTEM MAINTENANCE
The sensor for the ICC systemAis located
behind the INFINITI logo at the front of the
vehicle.
To keep the ICC system operating properly, be
sure to observe the following:
•Always keep area around the sensor clean.
•Do not strike or damage the areas around the
sensor. Do not touch or remove the screw
located on the sensor. Doing so could cause
failure or malfunction. If the sensor is dam-
aged due to an accident, it is recommended
you contact an INFINITI retailer.
•Do not cover or attach stickers (including
transparent material) or install an accessory
near the sensor. This could cause failure or
malfunction.
Radio frequency statement
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harm-
ful interference, and (2) this device must accept
any interference received, including interfer-
ence that may cause undesired operation.
NOTE
Changes or modification not expressly approved
by the party responsible for compliance could
void the user’s authority to operate the equip-
ment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause harmful interference, and
(2) this device must accept any interference re-
ceived, including interference that may cause
undesired operation of the device.
WARNING
Failure to follow the warnings and instructions
for proper use of the FEB system could result in
serious personal injury or death.
•The FEB system is a supplemental aid to the
driver. It is not a replacement for the driver’s
attention to traffic conditions or responsi-
bility to drive safely. It cannot prevent acci-
dents due to carelessness or dangerous
driving techniques.
•The FEB system does not function in all driv-
ing, traffic, weather and road conditions.
The FEB system can assist the driver when there
is a risk of a forward collision with the vehicle
ahead in the traveling lane.
NSD645
FORWARD EMERGENCY BRAKING (FEB)
SYSTEM (IF EQUIPPED)
5-60Starting and driving

The FEB system uses a radar sensorAlocated
behind the INFINITI logo to measure the dis-
tance to the vehicle ahead in the traveling lane.
FEB SYSTEM OPERATION
1Steering wheel mounted controls (left
side)
2Distance warning light
3Forward emergency braking OFF display
NSD645
NSD624
Starting and driving5-61

Autonomous braking function
If the driver does not react to the distance
warning signal in a critical situation, the FEB
system can assist with the autonomous braking
function
The autonomous braking function can help the
driver to avoid an accident or reduces the
effects of an accident.
The autonomous braking function is available in
the following speed ranges:
•4–125 MPH (7-200 km/h) for moving vehicles
•4–30 MPH (7 -50 km/h) for stationary ve-
hicles
Adaptive brake assist function
Adaptive brake assist function provides braking
assistance in hazardous situations at speeds
above 4MPH (7 km/h). It uses radar sensor
technology to assess the traffic situation.
If the system detects a risk of collision with the
vehicle in front, it calculates the braking force
necessary to avoid a collision. If you apply the
brakes forcefully, the adaptive brake assist
function will automatically increase the braking
force to a level suitable for the traffic condi-
tions.
If the adaptive brake assist function activates,
keep the brake pedal depressed until the emer-
gency braking situation is over. ABS prevents
the wheels from locking.
The brakes will work normally again if:
•You release the brake pedal.
•There is no longer any danger of a collision.
•No obstacle is detected in front of your
vehicle.
The brake assist function is then deactivated. At high speeds, the adaptive brake assist func-
tion is capable of reacting to moving objects
that have already been detected as such at
least once over the period of observation.
Up to a speed of approximately 45 MPH (70
km/h), the adaptive brake assist function reacts
to stationary vehicles.
Starting and driving5-63

FEB SYSTEM LIMITATIONS
WARNING
Listed below are the system limitations for the
FEB system. Failure to operate the vehicle in
accordance with these system limitations
could result in serious injury or death.
•The FEB system cannot detect all vehicles
under all conditions.
•The radar sensor does not detect the follow-
ing objects:– Pedestrians or animals
– Oncoming vehicles
– Crossing vehicles
•The radar sensor has some performance
limitations. For stationary vehicles, the FEB
system will not function when the vehicle is
driven at speeds over:
– Approximately 31 MPH (50 km/h) for the
Autonomous braking function.
•The radar sensor may not detect a vehicle
ahead in the following conditions:
– Dirt, ice, snow or other material covering
the radar sensor.
– Interference by other radar sources.
– Snow or heavy rain.
– If the vehicle ahead is narrow (e.g. mo-
torcycle). –
If the vehicle ahead is in a different lane.
– Under strong radar reflections, for ex-
ample, in a multi-level parking garage.
– New vehicle or after a maintenance of the
FEB system. For additional information,
see Break-in schedule later in this sec-
tion
– When driving on a steep downhill slope
or roads with sharp curves.
– When towing a trailer.
•In some road or traffic conditions, the FEB
system may intervene unnecessarily or give
an unnecessary warning. Always pay care-
ful attention to the traffic situation. Do not
rely solely on the distance warning function
and terminate the intervention if necessary.
•Braking distances increase on slippery sur-
faces.
•The system is designed to automatically
check the sensor’s functionality, within cer-
tain limitations. The system may not detect
some forms of obstruction of the sensor
area such as ice, snow, stickers, for ex-
ample. In these cases, the system may not
be able to warn the driver properly. Be sure
that you check, clean and clear the sensor
area regularly.
•Excessive noise will interfere with the warn-
ing chime sound, and the chime may not be
heard.
SYSTEM TEMPORARILY UNAVAILABLE
If the FEB stops working due to a malfunction or
some other reason, one of the following three
messages will be displayed in the vehicle infor-
mation display.
•[Emergency Brake Currently Unavailable See
Operator’s Manual]
•[Emergency Brake Inoperative]
•[Radar Sensors Dirty See Operator’s Manual]
For each of these messages, possible causes
and solutions are listed below.
[Emergency Brake Currently Unavailable See
Operator’s Manual]: The FEB system is tempo-
rarily inoperative. Possible causes:
•The radar sensor system is temporarily inop-
erative, for example, due to electromagnetic
radiation emitted by nearby TV or radio sta-
tions or other sources of electromagnetic
radiation.
•The system is outside the operating tempera-
ture range.
Starting and driving5-65

•The on-board voltage is too low.
Once the causes listed above no longer apply,
the display message goes out. The FEB system
is operative again.
If the display message does not disappear:
•Pull over and stop the vehicle safely as soon
as possible, paying attention to road and
traffic conditions.
•Secure the vehicle against rolling away.
•Switch off the engine.
[Emergency Brake Inoperative]: The FEB system
is temporarily inoperative due to a malfunction.
The adaptive brake assist function may also
have failed.
It is recommended you visit an INFINITI retailer.
[Radar Sensors Dirty See Operator’s Manual]:
The FEB system is temporarily restricted or
inoperative. Possible causes:
•The sensor behind the INFINITI logo is dirty.
•The function of the FEB system is impaired
due to heavy rain or snow. A warning tone also sounds.
Once the causes listed above no longer apply,
the display message goes out. The FEB system
is operative again.
If the display message does not disappear:
•Pull over and stop the vehicle safely as soon
as possible, paying attention to road and
traffic conditions.
•Secure the vehicle against rolling away.
•Switch off the engine.
•Clean the area around the sensors.
•Restart the engine. The display message
disappears.
SYSTEM MAINTENANCE
The sensorAis located behind the INFINITI
logo at the front of the vehicle.
To keep the system operating properly, be sure
to observe the following:
•Always keep the sensor area of the INFINITI
logo clean.
•Do not strike or damage the areas around the
sensor.
•Do not cover or attach stickers or similar
objects on the front bumper near the sensor
area. This could cause failure or malfunction.
•Do not attach metallic objects near the sen-
sor area (brush guard, etc.). This could cause
failure or malfunction.
NSD645
5-66Starting and driving

ACTIVE SOUND ENHANCEMENT
The active sound enhancement generates
sounds according to engine speed through the
speakers
2and woofer1(if equipped) to
enhance the quality of the engine sound. IPA is an electronic parking aid with ultrasound.
It detects vehicles and open spaces on both
sides of the vehicle. A parking symbol indicates
a suitable parking space. Active steering inter-
vention can assist you during parking and when
exiting a parking space. The driver controls the
accelerator, brake and gear shift. You may also
use the parking sensor system (see
Parking
sensor system (if equipped) later in this sec-
tion).
IMPORTANT SAFETY NOTES
WARNING
•IPA is only an aid. It is not a substitute for
your attention to the immediate surround-
ings. The responsibility for safe maneuver-
ing and parking remains with you.
•Make sure that no persons, animals or ob-
jects are in the maneuvering range
•When the parking sensor system is deacti-
vated, IPA is also unavailable.
•While parking or pulling out of a parking
space, the vehicle swings out and can drive
onto areas of the oncoming lane. This could
cause you to collide with other road users.
There is a risk of an accident.
•Pay attention to other road users. Stop the
vehicle if necessary or cancel the IPA park-
ing procedure
•This system is not designed to prevent con-
tact with small or moving objects.
•If your vehicle sustains damage to the bum-
per fascia, leaving it misaligned or bent, the
sensing zone may be altered causing inac-
curate measurement of obstacles or false
alarms.
•This system is not designed to prevent con-
tact with small or moving objects.
•If your vehicle sustains damage to the bum-
per fascia, leaving it misaligned or bent, the
sensing zone may be altered causing inac-
curate measurement of obstacles or false
alarms.
CAUTION
Do not drive over obstacles such as curbs, as
you may damage the wheels or tires.
IPA may also display spaces not suitable for
parking, for example:
•Parking or stopping prohibition.
INTELLIGENT PARKING ASSIST (IPA) (IF
EQUIPPED)
5-68Starting and driving

•In front of driveways or entrances and exits.
•Unsuitable surfaces.
Parking tips:
•On narrow roads, drive as closely as possible
past the parking space.
•Parking spaces that are littered or overgrown
might be identified or measured incorrectly.
•Parking spaces that are partly occupied by
trailer towing bars might not be identified as
such or be measured incorrectly.
•Snowfall or heavy rain may lead to a parking
space being measured inaccurately.
•Pay attention to the parking sensor system
warning messages during the parking proce-
dure.
•You can intervene in the steering procedure
to correct it at any time. IPA will then be
canceled.
•When transporting a load which protrudes
from your vehicle, you should not use IPA.
•Never use IPA when snow chains are fitted.
•Make sure that the tire pressures are always
correct. This has a direct influence on the
parking characteristics of the vehicle. Use IPA for parking spaces that are:
•Parallel or at right angles to the direction of
travel.
•On straight roads, not bends.
•On the same level as the road, e. g. not on
the sidewalk.
For vehicles with the towbar folded out, the
minimum length for parking spaces is slightly
longer.
If you have attached a trailer to your vehicle,
you may not use IPA. Once the electrical con-
nection is established between your vehicle and
the trailer, IPA is no longer available. The
parking sensor system is deactivated for the
rear area
DETECTING PARKING SPACES
The IPA system can only be used to park in
spaces that have vehicles directly on either side
of the parking space.
Objects located above the height range of IPA
will not be detected when the parking space is
measured. These are not taken into account
when the parking procedure is calculated, e. g.
overhanging loads, tail sections or loading
ramps of goods vehicles.
WARNING
If there are objects above the detection range,
IPA may steer too early. This could cause a
collision. There is a risk of an accident.
If objects are located above the detection
range, stop and switch off the IPA.
For further information on the detection range
see Range of the sensors later in this section.
IPA does not assist you parking in spaces at
right angles to the direction of travel if:
•Two parking spaces are located directly next
to one another.
•The parking space is directly next to a low
obstacle such as a low curb.
•You forward park.
IPA does not assist you parking in spaces that
are parallel or at right angles to the direction of
travel if:
•The parking space is on a curb.
•The system reads the parking space as being
blocked, for example, by foliage or grass
paving blocks.
•The area is too small for the vehicle to
maneuver into.
Starting and driving5-69

•The parking space is bordered by an ob-
stacle, e.g. a tree, a post or a trailer.
1Detected parking space on the left.
2Parking symbol.
3Detected parking space on the right.
IPA is activated automatically when driving for-
wards. The system is operational at speeds of
up to approximately 19 MPH (30 km/h). While in
operation, the system independently locates
and measures parking spaces on both sides of
the vehicle
IPA will only detect parking spaces:
•Adjacent to the vehicle.
•Parallel or at right angles to the direction of
travel.
•That are parallel to the direction of travel and
are at least 5 ft (1.5 m) wide.
•That are parallel to the direction of travel and
at least 3.3 ft (1.0 m) longer than your
vehicle.
•That are at right angles to the direction of
travel and at least 3.3 ft (1.0 m) wider than
your vehicle.
NOTE
IPA cannot measure the length of a parking
space if it is at right angles to the direction of
travel. You will need to judge whether your ve-
hicle will fit in the parking space
When driving at speeds below 19 MPH (30
km/h) you will see parking symbol
2as a
status indicator in the vehicle information dis-
play. When a parking space has been detected,
an arrow towards the right
3or the left1also
appears. IPA only displays parking spaces on
the front-passenger side as standard. Parking
spaces on the driver’s side are displayed as
soon as the turn signal on the driver’s side is
activated. When parking on the driver’s side,
this must remain activated until you confirm the
use of IPA by pressing the <OK>button on the
steering wheel. The system automatically deter-
mines whether the parking space is parallel or
at right angles to the direction of travel. A parking space is displayed while you are
driving past it, and until you are approximately
50 ft (15 m) away from it.
PARKING
NOTE
When the parking sensor system detects ob-
stacles, you are responsible for braking in good
time.
1. Stop the vehicle when the parking symbol
shows the desired parking space in the
combination meter
2. Shift into position R. The [Start Park Assist? Yes: OK No:]
message appears in the vehicle information
display.
3. To cancel the procedure: press the
button on the steering wheel or pull away
or
4. To park using IPA press the <OK>button on
the steering wheel. The Park Assist [Observe
surroundings] message appears in the ve-
hicle information display.
5. Release the steering wheel.
6. Back up the vehicle, being ready to brake at all times. When backing up, drive at a speed
NSD612Upper display
5-70Starting and driving

below 5 MPH (10 km/h). Otherwise, IPA will
be canceled.
7. Stop as soon as the parking sensor system sounds the continuous warning tone, if not
before. Maneuvering may be required in
tight parking spaces.
The [Park Assist active Select D Observe
surroundings] message appears in the ve-
hicle information display.
8. Select transmission position D (Drive) while the vehicle is stationary.
IPA immediately steers in the other direc-
tion.
The [Park Assist Observe surroundings] mes-
sage appears in the vehicle information dis-
play.
NOTE
You will achieve the best results by waiting
for the steering procedure to complete before
pulling away.
9. Drive forwards and be ready to brake at all times.
Maneuvering may be required in tight park-
ing spaces. Drive forward and back up as
prompted by the parking sensor system
warning displays, several times if necessary. 10. Stop as soon as the parking sensor system
sounds the continuous warning tone, if not
before.
The [Park Assist active Select R] [Observe
surroundings] message appears in the ve-
hicle information display.
As soon as the parking procedure is com-
plete the [Park Assist switched off] mes-
sage appears and a warning tone sounds.
The vehicle is now parked.
11. Before leaving the vehicle, secure the ve- hicle against rolling away unintentionally:
•The electric parking brake must be ap-
plied.
•The transmission must be in position P
(Park) and the transmission position dis-
play must show P in the vehicle informa-
tion display.
•The key must be removed from the igni-
tion switch.
•On uphill or downhill gradients, the front
wheels must be turned towards the curb.
IPA no longer supports you with steering inter-
ventions. When IPA is finished, you must steer
again yourself. The parking sensor system is
still available. Parking tips:
•The way your vehicle is positioned in the
parking space after parking is dependent on
various factors. These include the position
and shape of the vehicles parked in front and
behind it and the conditions of the location.
It may be the case that IPA guides you too far
into a parking space, or not far enough into
it. In some cases, it may also lead you across
or onto the curb. If necessary you should
cancel the parking procedure with IPA.
•During the parking maneuver, the system will
indicate when you should shift to R (Reverse)
or D (Drive). However, you can freely choose
to shift gear whenever you feel you need to.
Should the transmission change take place
too early, the parking procedure will be
canceled. A sensible parking position can no
longer be achieved from this position.
EXITING A PARKING SPACE
In order that IPA can support when exiting the
parking space:
•You need to have parked using IPA.
•The border of the parking space must be high
enough at the front and the rear. A curb
stone is too small, for example.
Starting and driving5-71