Vic INFINITI QX30 2017 Owners Manual

WARNING
•Never leave children or adults who would
normally require the support of others alone
in your vehicle. Pets should not be left alone
either. They could unknowingly activate
switches or controls and inadvertently be-
come involved in a serious accident and in-
jure themselves. On hot, sunny days, tem-
peratures in a closed vehicle could quickly
become high enough to cause severe or
possibly fatal illness to people or animals.
•Properly secure all cargo to help prevent it
from sliding or shifting. Do not place cargo
higher than the seatbacks. In a sudden stop
or collision, unsecured cargo could cause
personal injury.
•To avoid raising the center of gravity exces-
sively, do not exceed the rated capacity of
the roof rack (if so equipped) and evenly
distribute the load.
EXHAUST GAS (CARBON MONOXIDE)
WARNING
•Do not breathe exhaust gas; it contains
colorless and odorless carbon monoxide.
Carbon monoxide is dangerous. It can cause
unconsciousness or death.
•If you suspect that exhaust fumes are entering
the vehicle, drive with all windows fully open,
and have the vehicle inspected immediately.
•Do not run the engine in closed spaces such
as a garage.
•Do not park the vehicle with the engine
running for an extended period of time.
•Keep the lift gate closed while driving, other-
wise exhaust gas could be drawn into the pas-
senger compartment. If you must drive with
the lift gate open, follow these precautions:
–Open all the windows.
–Turn the air recirculation switch off and
set the fan control to the highest level to
circulate the air.
•If electrical wiring or other cable connec-
tions must pass to a trailer through the seal
ion the lift gate or body, follow the manufac-
turer’s recommendations to prevent carbon
monoxide entry into the vehicle.
•The exhaust system and body should be
inspected by a qualified mechanic when-
ever:
–You suspect that exhaust fumes are en-
tering into the passenger compartment.
–You notice a change in the sound of the
exhaust system.
–You have had an accident involving dam-
age to the exhaust system, underbody,
or rear of the vehicle.
THREE-WAY CATALYST (IF EQUIPPED)
The three-way catalyst is an emission control
device installed in the exhaust system. Exhaust
gas in the three-way catalyst is burned at high
temperatures to help reduce pollutants.
WARNING
•The exhaust gas and the exhaust system
are very hot. Keep people, animals and
flammable materials away from the exhaust
system components.
•Do not stop or park the vehicle over flam-
mable materials such as dry grass, waste-
paper or rags. They may ignite and cause a
fire.
PRECAUTIONS WHEN STARTING AND
DRIVING
5-4Starting and driving

CAUTION
•Do not use leaded gasoline. (SeeRecom-
mended fluids/lubricants and capacitiesin
the9. Maintenance and Schedulessec-
tion.) Deposits from leaded gasoline seri-
ously reduce the ability of the three-way
catalyst to help reduce exhaust pollutants
and/or damage the three-way catalyst.
•Keep your engine tuned up. Malfunctions in
the ignition, fuel injection, or electrical sys-
tems may cause overrich fuel to flow into
the three-way catalyst, causing it to over-
heat. Do not keep driving if the engine mis-
fires, or if noticeable loss of performance or
other unusual operating conditions are de-
tected. Have the vehicle inspected
promptly. It is recommended you visit an
INFINITI retailer for this service.
•Avoid driving with an extremely low fuel
level. Running out of fuel could cause the
engine to misfire, damaging the three-way
catalyst.
•Do not race the engine while warming it up.
•Do not push or tow your vehicle to start the
engine.
TIRE PRESSURE MONITORING SYSTEM
(TPMS)
Each tire, including the spare (if present),
should be checked monthly when cold and
inflated to the inflation pressure recommended
by the vehicle manufacturer on the vehicle
placard or tire inflation pressure label. (If your
vehicle has tires of a different size than the size
indicated on the vehicle placard or tire inflation
pressure label, you should determine the
proper tire inflation pressure for those tires.)
As an added safety feature, your vehicle has
been equipped with a tire pressure monitoring
system (TPMS) that illuminates a low tire pres-
sure telltale when one or more of your tires is
significantly under-inflated. Accordingly, when
the low tire pressure telltale illuminates, you
should stop and check your tires as soon as
possible, and inflate them to the proper pres-
sure. Driving on a significantly under-inflated
tire causes the tire to overheat and can lead to
tire failure. Under-inflation also reduces fuel
efficiency and tire tread life, and may affect the
vehicle’s handling and stopping ability.
Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the driver’s
responsibility to maintain correct tire pressure,
even if under-inflation has not reached the level
to trigger illumination of the TPMS low tire
pressure telltale.
Your vehicle has also been equipped with a TPMS
malfunction indicator to indicate when the sys-
tem is not operating properly. The TPMS malfunc-
tion indicator is combined with the low tire
pressure telltale. When the system detects a
malfunction, the telltale will flash for approxi-
mately one minute and then remain continuously
illuminated. This sequence will continue upon
subsequent vehicle start-ups as long as the mal-
function exists. When the malfunction indicator is
illuminated, the system may not be able to detect
or signal low tire pressure as intended. TPMS
malfunctions may occur for a variety of reasons,
including the installation of replacement or alter-
nate tires or wheels on the vehicle that prevent
the TPMS from working properly. Always check
the TPMS telltale after replacing one or more tires
or wheels on your vehicle to ensure that the
replacement or alternate tires and wheels allow
the TPMS to continue to function properly.
The vehicle’s wheels have sensors fitted that
monitor the tire pressures in all four tires The
tire pressure monitor warns you if the pressure
drops in one or more of the tires The tire
pressure monitor only functions if the corre-
sponding sensors are fitted to all wheels.
Information on tire pressures is shown in the
vehicle information display. After a few minutes
of driving, the current tire pressure of each tire
is shown in the [Serv.] menu of the vehicle
information display.
Starting and driving5-5

WARNING
•Radio waves could adversely affect electri-
cal medical equipment. Those who use a
pacemake should contact their electrical
medical equipment manufacturer for the
pssible influences before use.
•If the low tire pressure warning light illumi-
nates or a tire pressure-related warning is
displayed by the vehicle information dis-
play while driving, avoid sudden steering
maneuvers or abrupt braking, reduce ve-
hicle speed, pull off the road to a safe loca-
tion and stop the vehicle as soon as pos-
sible. Driving with under-inflated tires may
permanently damage the tires and increase
the likelihood of tire failure. Serious vehicle
damage could occur and may lead to an ac-cident and could result in serious personal
injury. Check the tire pressure for all four
tires. Adjust the tire pressure to the recom-
mended COLD tire pressure shown on the
tire and loading information label to turn
the low tire pressure warning light OFF. If
you have a flat tire, replace it with a replace-
ment tire as soon as possible.
•If a replacement wheel is fitted without an
INFINITI TPMS Sensor, the TPMS will not
function and the low tire pressure warning
light will flash for approximately 1 minute.
The light will remain on after 1 minute. It is
recommended you contact an INFINITI re-
tailer as soon as possible for tire replace-
ment and/or system resetting.
•For models with run-flat tires, although you
can continue driving with a punctured run-flat
tire, remember that vehicle handling stability
is reduced, which could lead to an accident
and personal injury. Also, driving a long dis-
tance at high speeds may damage the tires.
–Do not drive at speeds above 50 MPH (80
km/h) and do not drive more than approxi-
mately 93 miles (150 km) with a punctured
run-flat tire. The actual distance the ve-
hicle can be driven on a flat tire depends
on outside temperature, vehicle load, road
conditions and other factors.
–If you detect any unusual sounds or
vibrations while driving with a punctured
run-flat tire, pull off the road to a safe
location and stop the vehicle as soon as
possible. The tire may be seriously dam-
aged and need to be replaced.
•Replacing tires with those not originally
specified by INFINITI could affect the proper
operation of the TPMS.
•If you used Emergency Tire Sealant to repair
a minor tire puncture, the TPMS sensor
should be checked when repairing or re-
placing the tire (for models equipped with
the emergency tire puncture repair kit). It is
recommended you visit an INFINITI retailer
for this service.
•INFINITI recommends using only INFINITI
Genuine Emergency Tire Sealant provided
with your vehicle. Other tire sealants may
damage the valve stem seal which can
cause the tire to lose air pressure (for mod-
els equipped with the emergency tire punc-
ture repair kit).
NSD633
5-6Starting and driving

Perform the following procedures to restart the
TPMS.
NOTE
Before restarting, make sure that the tire pres-
sures are set properly on all four tires for the
respective operating conditions. The recom-
mended tire pressures can be found in the tire
pressure placard on the driver’ door pillar.
1. Make sure that the ignition switch is in the
ON position.
2. Press the
orbutton on the
steering wheel to select the [Serv.] menu.
3. Press the
orbutton to select
[Tire Pressure].
4. Press <OK> to confirm.
The vehicle information display shows the
current tire pressure for each tire or the [Tire
pressures will be displayed after driving a
few minutes] message.
If you wish to confirm the restart:
5. Press <OK> to confirm.
The [Tire Press. Monitor Restarted] message
appears in the vehicle information display.
After you have driven for a few minutes, the
system checks whether the current tire pres-sures are within the specified range The new
tire pressures are then accepted as refer-
ence values and monitored
If you wish to cancel the restart:
6. Press the
button.
The tire pressure values stored at the last
restart will continue to be monitored
FCC Notice:
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harm-
ful interference, and (2) this device must accept
any interference received, including interfer-
ence that may cause undesired operation.
NOTE
Changes or modifications not expressly ap-
proved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause interference, and (2) this
device must accept any interference, includinginterference that may cause undesired opera-
tion of the device.
ON PAVEMENT AND OFF-ROAD
DRIVING PRECAUTIONS
Utility vehicles have a significantly higher roll-
over rate than other types of vehicles.
They have higher ground clearance than pas-
senger cars to make them capable of perform-
ing in a variety of on-pavement and off-road
applications. This gives them a higher center of
gravity than ordinary vehicles. An advantage of
higher ground clearance is a better view of the
road, allowing you to anticipate problems. How-
ever, they are not designed for cornering at the
same speeds as conventional 2-wheel drive
vehicles any more than low-slung sports cars
are designed to perform satisfactorily under
off-road conditions. If at all possible, avoid
sharp turns at high speeds. As with other
vehicles of this type, failure to operate this
vehicle correctly may result in loss of control or
vehicle rollover. In a rollover crash, an unbelted
person is significantly more likely to die than a
person wearing a seat belt.
For additional information, refer toDriving
safety precautionslater in this section.
Starting and driving5-9

•The vehicle generally moves or pulls in the
direction of the flat tire.
•Do not rapidly apply the brakes.
•Do not rapidly release the accelerator
pedal.
•Do not rapidly turn the steering wheel.
1. Remain calm and do not overreact.
2. Maintain a firm grip on the steering wheel
with both hands and try to hold a straight
course.
3. When appropriate, slowly release the accel-
erator pedal to gradually slow the vehicle.
4. Gradually steer the vehicle to a safe location
off the road and away from traffic if possible.
5. Lightly apply the brake pedal to gradually
stop the vehicle.
6. Turn on the hazard warning flashers and
contact a roadside emergency service to
change the tire. For additional information,
refer toFlat tirein the6. In case of
emergencysection.
DRINKING ALCOHOL/DRUGS AND
DRIVING
WARNING
Never drive under the influence of alcohol or
drugs. Alcohol in the bloodstream reduces co-
ordination, delays reaction time and impairs
judgement. Driving after drinking alcohol in-
creases the likelihood of being involved in an
accident injuring yourself and others. Addi-
tionally, if you are injured in an accident, alco-
hol can increase the severity of the injury.
INFINITI is committed to safe driving. However,
you must choose not to drive under the influ-
ence of alcohol. Every year thousands of people
are injured or killed in alcohol-related acci-
dents. Although the local laws vary on what is
considered to be legally intoxicated, the fact is
that alcohol affects all people differently and
most people underestimate the effects of alco-
hol.
Remember, drinking and driving don’t mix! And
that is true for drugs, too (over-the-counter,
prescription, and illegal drugs). Don’t drive if
your ability to operate your vehicle is impaired
by alcohol, drugs, or some other physical con-
dition.
DRIVING SAFETY PRECAUTIONS
Your INFINITI is designed for both normal and
off-road use. However, avoid driving in deep
water or mud as your INFINITI is mainly de-
signed for leisure use, unlike a conventional
off-road vehicle.
Remember that 2–wheel drive vehicles are less
capable than all-wheel drive (AWD) models for
rough road driving and extrication when stuck
in deep snow or mud, or the like.
Please observe the following precautions:
WARNING
•Spinning the front wheels on slippery sur-
faces may cause the AWD warning message
to display and the AWD system to automati-
cally switch from the AWD to 2WD mode.
This could reduce the traction. Be especially
careful when towing a trailer. (AWD models)
•Drive carefully when off the road and avoid
dangerous areas. Every person who drives
or rides in this vehicle should be seated
with their seat belt fastened. This will keep
you and your passengers in position when
driving over rough terrain.
Starting and driving5-11

The INFINITI Vehicle Immobilizer System will not
allow the engine to start without the use of the
registered key.
If the engine fails to start using the registered
key, it may be due to interference caused by
another registered key, an automated toll road
device or automated payment device on the key
ring. Restart the engine using the following
procedures:
1. Leave the ignition switch in the ON position
for approximately 5 seconds.
2. Turn the ignition switch to the OFF or LOCK
position and wait approximately 5 seconds.
3. Repeat Step 1 and 2 again.
4. Restart the engine while holding the device
(which may have caused the interference)
separate from the registered key.
If the no start condition re-occurs, INFINITI
recommends placing the registered key on a
separate key ring to avoid interference from
other devices.
0OFF position
1ACC position
2ON position
3START position
WARNING
Never remove the key or turn the ignition
switch to the OFF position while driving. The
steering wheel will lock and could cause the
driver to lose control of the vehicle. This could
result in serious vehicle damage or personal
injury.
CAUTION
Use electrical accessories with the engine run-
ning to avoid discharging the vehicle battery.
If you must use accessories while the engine is
not running, do not use them for extended pe-
riods of time and do not use multiple electrical
accessories at the same time.
The switch includes an anti-theft steering lock
device.
STEERING LOCK
To lock the steering wheel
1. Turn the key to the OFF position.
2. Remove the key from the ignition switch.
3. Turn the steering wheel 1/6 of a turn
clockwise from the straight up position.
To unlock the steering wheel
1. Insert the key into the ignition switch.
2. Gently turn the key while rotating the
steering wheel slightly right and left.
NPA1483
INFINITI VEHICLE IMMOBILIZER SYSTEM IGNITION SWITCH
5-14Starting and driving

WARNING
Apply the parking brake if the shift lever is in
any position while the engine is not running.
Failure to do so could cause the vehicle to move
unexpectedly or roll away and result in serious
personal injury or property damage.
CAUTION
Use the P (Park) or R (Reverse) position only
when the vehicle is completely stopped.
P (Park)
:
CAUTION
To prevent transmission damage, use the P
(Park) position only when the vehicle is com-
pletely stopped.
Use this position when the vehicle is parked or
when starting the engine. Always make sure
that the vehicle is completely stopped before
pressing button
1to engage the P (Park)
position. For maximum safety, the brake pedal
must be depressed before engaging the P (Park)
position. Use this position together with the
parking brake. When parking on a hill, first
depress the brake pedal, apply the parking
brake and then engage the P (Park) position.
The parking lock should not be used as a brake
when parking. In order to secure the vehicle,always apply the electric parking brake in addi-
tion to the parking lock.
In the event of a malfunction of the vehicle’s
electronics, the transmission may lock in posi-
tion P (Park). Have the vehicle electronics
checked immediately. It is recommended you
visit an INFINITI retailer for this service.
Park position P is automatically engaged if:
•You switch off the engine using the key and
remove the key.
•You open the driver’s door when the vehicle
is stationary or driving at very low speed and
the transmission is in position D (Drive) or R
(Reverse).
R (Reverse)
:
CAUTION
To prevent transmission damage, use the R
(Reverse) position only when the vehicle is
completely stopped.
Use this position to back up the vehicle.
Make sure the vehicle is completely stopped
before selecting the R (Reverse) position.The
brake pedal must be depressed and the shift
lever button pushed in to move the shift lever
from P (Park), N (Neutral) or any drive position to
R (Reverse).
NSD586
Starting and driving5-19

Deactivating the temporary manual drive program:
Pull and hold the right steering wheel gearshift
paddle until the automatic transmission shifts into
the last active automatic drive program E or S.
When manual drive program M is deactivated,
the automatic transmission in automatic drive
program E or S may shift from the current gear
into a higher or lower gear. This is dependent
on the position of the accelerator pedal, speed
and load.Problems with the transmission
:
Problem Possible causes/consequences and solutions
The transmission has problems shift-
ing gearThe transmission is losing oil.
Have the transmission checked immediately. It is recommended you
visit an INFINITI retailer for this service.
The acceleration ability is deteriorat-
ing The transmission no longer shifts
into all of the gears Reverse gear can
no longer be engagedThe transmission is in emergency mode.
•Stop.•Shift the transmission to position P (Park).•Switch off the engine.•Wait at least ten seconds before restarting the engine.•Shift the transmission to position D (Drive).•Have the transmission checked immediately. It is recommended
you visit an INFINITI retailer for this service.
5-24Starting and driving

HOW TO ENABLE/DISABLE THE LDW
SYSTEM
1. Press theorbutton on the
steering wheel
1to select the [DriveAssist]
menu on the Menu bar
B.
2. Press the
orbutton to select
[Lane Departure Warning].
3. Press the<OK>button on the steering wheel
1. The current selection is displayed.
4. Press the<OK>to confirm.
5. Press the
orbutton to set [Off],
[Standard] or [Adaptive].
6. Press the<OK>button to save the setting.
When the LDW is activated, the vehicle
information display shows the lane mark-ings as bright lines in the assistance graphic
in the display area
A
When [Standard] is selected, no warning vibra-
tion occurs if:
•You have switched on the turn signals. In
this event, the warnings are suppressed for a
certain period of time.
•A driving safety system intervenes, such as
ABS, brake assist system (BAS) or VDC.
When [Adaptive] is selected, no warning vibra-
tion occurs if:
•You have switched on the turn signals. In
this case the warnings are suppressed for a
certain period of time.
•A driving system intervenes, such as ABS,
BAS or VDC.
•You accelerate forcefully.
•You brake forcefully.
•You steer actively, for example, swerve to
avoid an obstacle or change lane quickly.
•You cut the corner on a sharp bend.
The system may detect certain conditions and
warns you accordingly.The warning vibration occurs earlier if:
•You approach the outer lane marking on a
bend.
•The road has very wide lanes, for example, a
freeway.
•The system detects solid lane markings.
The warning vibration occurs later if:
•The road has narrow lanes.
•You cut across a corner on a bend.
LDW SYSTEM LIMITATIONS
WARNING
Listed below are the system limitations for the
LDW system. Failure to operate the vehicle in
accordance with these system limitations
could result in serious injury or death.
•This system is only a warning device to
inform the driver of a potential unintended
lane departure. It will not steer the vehicle
or prevent loss of control. It is the driver’s
responsibility to stay alert, drive safely,
keep the vehicle in the traveling lane, and
be in control of the vehicle at all times.
•The system will not operate at speeds be-
low approximately 40 MPH (60 km/h) or if it
cannot detect lane markers.
NSD599Assistance graphic
Starting and driving5-31

SYSTEM MALFUNCTION
If the LDW system malfunctions, it will cancel
automatically, and the message [Lane Depar-
ture Warning Inoperative] will appear.
Action to take:
Stop the vehicle in a safe location,
engage P (Park), turn the engine off and restart the
engine. If the message continues to appear, have
the system checked. It is recommended you visit
an INFINITI retailer for this service.
SYSTEM MAINTENANCE
The lane camera unit1for the LDW system is
located above the inside mirror.
To ensure the proper operation of the LDW
system and prevent a system malfunction, be
sure to observe the following:
•Always keep the windshield clean.
•Do not attach a sticker (including transpar-
ent material) or install an accessory near the
camera unit.
•Do not place reflective materials, such as
white paper or a mirror, on the instrument
panel. The reflection of sunlight may ad-
versely affect the camera unit’s capability of
detecting the lane markers.
•Do not strike or damage the areas around
the camera unit. Do not touch the camera
lens or remove parts from the camera unit. If
the camera unit is damaged due to an acci-
dent, it is recommended you contact an
INFINITI retailer.
NSD644
5-34Starting and driving