ESP INFINITI QX30 2017 Owner's Guide

Page 243 of 531

FM radio reception
MAXIMUM SIGNAL DISTANCES
•FM : 25 to 30 miles (40 to 48 km)
•AM : 60 to 130 miles (97 to 209 km)
Range: FM range is normally limited to 25 to 30
miles (40 to 48 km), with monaural (single
station) FM having slightly more range than
stereo FM. External influences may sometimes
interfere with FM station reception even if the
FM station is within 25 miles (40 km). The
strength of the FM signal is directly related to
the distance between the transmitter and re-
ceiver. FM signals follow a line-of-sight path,
exhibiting many of the same characteristics as
light. For example they will reflect off objects.
Fade and drift: As your vehicle moves away from
a station transmitter, the signals will tend to
fade and/or drift.Static and flutter: During signal interference
from buildings, large hills or due to antenna
position, usually in conjunction with an in-
creased distance from the station transmitter,
static or flutter can be heard. This can be
reduced by lowering the treble setting to reduce
the treble response.
Multipath reception: Because of the reflective
characteristics of FM signals, direct and re-
flected signals reach the receiver at the same
time. The signals may cancel each other, result-
ing in momentary flutter or loss of sound.
AM radio reception
AM signals, because of their low frequency, can
bend around objects and skip along the ground.
In addition, the signals can bounce off the
ionosphere and be bent back to earth. Because
of these characteristics, AM signals are also
subject to interference as they travel from trans-
mitter to receiver.
Fading: This occurs while the vehicle is passing
through freeway underpasses or in areas with
many tall buildings. It can also occur for several
seconds during ionospheric turbulence even in
areas where no obstacles exist.
Static: Caused by thunderstorms, electrical
power lines, electric signs and even traffic
lights.
HD RadioTMTechnology reception
(for U.S.)
HD RadioTMTechnology reception needs to be
activated to receive HD Radio broadcasts, see
Audio settingslater in this section.
This enables you to receive radio broadcasts
digitally (where available), providing a better
quality sound with clear reception. When this
feature is not activated or HD Radio broadcasts
are not available, you will receive analog radio
(AM/FM) broadcasts.
Satellite radio reception
When the satellite radio is used for the first time
or the battery has been replaced, the satellite
radio may not work properly. This is not a
malfunction. Wait more than 10 minutes with
the satellite radio ON and the vehicle outside of
any metal or large building for the satellite
radio to receive all of the necessary data.
The satellite radio requires an active SiriusXM
Satellite Radio subscription. The satellite ser-
vice is a available only to those at least 18 and
older in the 48 contiguous United States.
The satellite radio performance may be affected
if cargo carried on the roof blocks the satellite
radio signal.
SAA0306Z
4-54Display screen, heater and air conditioner, and audio system

Page 244 of 531

If possible, do not put cargo near the satellite
antenna.
The build up of ice on the satellite radio an-
tenna can affect satellite radio performance.
Remove the ice to restore satellite radio recep-
tion.
Trademarks
HD Radio Technology manufactured under li-
cense from iBiuity Digital Corporation. U.S. and
Foreign Patents. HD Radio
TMand the HD, HD
Radio, and “Arc” logos are proprietary trade-
marks of iBiquity Digita; Corp.
The Bluetooth® word mark and logos are reg-
istered trademarks owned by Bluetooth SIG,
Inc. and any use of such marks by DENSO
CORPORATION is under license. Other trade-
marks and trade names are those of their
respective owners.
SiriusXM services require a subscription after
trial period and are sold separately or as a
package. Our satellite service is available only
to those at least 18 and older in the 48 contigu-
ous USA and DC. For more information visit
www.siriusxm.com.
Required SiriusXM Satellite Radio and SiriusXM
Travel Link monthly subscriptions are sold
separately. Sirius XM Travel Link is only avail-
able in select markets. For more information,
see www.sirius.com/travellink
“Made for iPodR” and “Made for iPhoneR”
mean that an electronic accessory has been
designed to connect specifically to iPod
Ror
iPhone
R, respectively, and has been certified
by the developer to meet Apple performance
standards. Apple is not responsible for the
operation of this device or its compliance with
safety and regulatory standards. Please note
that the use of this accessory with iPod
Ror
iPhone
Rmay affect wireless performance.
Apple, the Apple logo, iPhone
R, iPodR, iPod
classic
R, iPod nanoR, and iPod touchRare trademarks of Apple Inc., registered in the
U.S. and other countries. Lightning is a trade-
mark of Apple Inc. App Store is a service mark of
Apple Inc.
Music recognition technology and related data
are provided by Gracenote®. Gracenote is the
industry standard in music recognition technol-
ogy and related content delivery. For more
information, visit www.gracenote.com.
CD and music-related data from Gracenote, Inc.,
copyright
c2000 to present Gracenote.
Gracenote Software, copyright
c2000 to pres-
ent Gracenote. One or more patents owned by
Gracenote apply to this product and service.
See the Gracenote website for a non-exhaustive
list of applicable Gracenote patents. Gracenote,
CDDB, MusicID, MediaVOCS, the Gracenote
logo and logotype, and the “Powered by
Gracenote” logo are either registered trade-
marks or trademarks of Gracenote in the United
States and/or other countries.
App Store
SM
Apple and the Apple logo are trademarks of Apple
Inc., registered in the U.S. and other countries.
App Store is a service mark of Apple Inc.
Google PlayTM
Google Play is a trademark of Google Inc.
Google
c2012 Google Inc. All rights reserved. Google
CalendarTMcalendaring application is a trade-
mark of Google Inc.
Display screen, heater and air conditioner, and audio system4-55

Page 247 of 531

This system supports various USB memory de-
vices, USB hard drives and iPod players. Some
USB devices may not be supported by this
system.
•Partitioned USB devices may not play cor-
rectly.
•Some characters used in other languages
(Chinese, Japanese, etc.) may not appear
properly in the display. Using English lan-
guage characters with a USB device is rec-
ommended.
General notes for USB use
:
Refer to your device manufacturer’s owner in-
formation regarding the proper use and care of
the device.
Notes for iPod use
:
iPod is a trademark of Apple Inc., registered in
the U.S. and other countries.
•Improperly plugging in the iPod may cause a
checkmark to be displayed on and off (flick-
ering). Always make sure that the iPod is
connected properly.
•An iPod nano (1st Generation) may remain in
fast forward or rewind mode if it is connected
during a seek operation. In this case, please
manually reset the iPod.
•An iPod nano (2nd Generation) will continue
to fast-forward or rewind if it is disconnected
during a seek operation.
•An incorrect song title may appear when the
Play Mode is changed while using an iPod
nano (2nd Generation)
•Audiobooks may not play in the same order
as they appear on an iPod.
•Large video files cause slow responses in an
iPod. The vehicle display may momentarily
black out, but will soon recover.
•If an iPod automatically selects large video
files while in the shuffle mode, the vehicle
display may momentarily black out, but will
soon recover.
4-58Display screen, heater and air conditioner, and audio system

Page 252 of 531

Windows Media Player:
This product is protected by certain intellectual
property right of Microsoft. Use or distribution
of such technology outside of this product is
prohibited without a license from Microsoft.
Bluetooth® Audio player
The Bluetooth® word mark and logos are reg-
istered trademarks owned by Bluetooth SIG,
Inc. and any use of such marks by DENSO
CORPORATION is under license. Other trade-
marks and trade names are those of their
respective owners.
•Some Bluetooth® streaming audio devices
may not be recognized by the in-vehicle
audio system.
•It is necessary to set up the wireless con-
nection between a compatible Bluetooth®
streaming audio device and the in-vehicle
Bluetooth® module before using the
Bluetooth® streaming audio.
•The Bluetooth® streaming audio may be
stopped under the following conditions:
– When receiving a hands-free call
– When checking the connection to the
hands-free phone
– When connecting the hands-free phone
or the audio device
– When downloading a phonebook memory
from a connected cellular phone
•Do not place a Bluetooth® streaming audio
device in an area surrounded by metal or far
away from the in-vehicle Bluetooth® module
to prevent tone quality degradation and wire-
less connection disruption.
•While an audio device is connected through
Bluetooth® wireless connection, the battery
of the device may discharge quicker than
usual.
•This system supports the Bluetooth® Ad-
vanced Audio Distribution Profile (A2DP) and
Audio/Video Remote Control Profile (AVRCP).
•Wireless LAN (Wi-Fi) and the Bluetooth®
functions share the same frequency band
(2.4 GHz). Using the Bluetooth® and the
wireless LAN functions at the same time may
slow down or disconnect the communication
and cause undesired noise. It is recom-
mended that you turn off the wireless LAN
(Wi-Fi) when using the Bluetooth® functions.
Display screen, heater and air conditioner, and audio system4-63

Page 258 of 531

2. Tune to the station/channel you wish to
store in the preset list.
3. (Radio screen operation) Touch and hold
one of the preset numbers in the preset list.
(Radio memory buttons operation) Push and
hold the desired station/channel preset but-
ton <1> to <6>.
4. The information such as frequency (AM/FM),
channel number (SXM), etc. will be dis-
played on the preset list.
To change the preset stations/channels, touch
and hold one of the preset numbers. You can
select whether to change the station/channel or
to delete the preset setting.
Alert notification (SXM only)
:
Favorite artists and songs can be registered to
receive an alert notice wen a song of the
registered conditions is on the radio. To tune to
the respective channel, touch [Listen to be
consistent]. The alert can be ignored by touch-
ing [Cancel].
Satellite Radio:
•The satellite mode requires and active
SiriusXM Satellite Radio subscription. The
satellite service is available only to those at
least 18 and older in the 48 contiguous
United States.
•It may take some time to receive the activa-
tion signal after the initiation of the SiriusXM
Satellite Radio subscription. After receiving
the activation signal, an available channel
list will automatially be updated in the radio.
Switch the ignition switch from LOCK to ACC
to update the SiriusXM channel list.
Radio Controls
Touch [Control] on the AM, FM or SXM screen to
display the control screen.
The following items are available:
FM/AM
:
•[Station List]
Touch to display the available station list.
While listening to FM radio, Auto Update is
not performed.
•[Scan]
Touch to scan tune the stations
SeeRadio operationearlier in this section
•[HD mode]
When this item is turned on, the analog and
digital reception switches automatically.
When this item is turned off, te reception is
fixed in the analog mode.
•[HD Info]
Touch to display the HD Radio information
such as name of song, artist and album.
This item is available when [RDS Info] is not
active.
•[Tag] (HD Radio broadcasts only)
Touch to register the tag information for
iTunes Tagging. If an iPod is plugged in after
the registration, the tag information can be
stored in an iPod and be used to purchase
the songs via iTunes.
•[RDS Info] (FM only)
Touch to display the RDS information.
This item is available only when [HD Radio
Info] is not active.
SXM
:
•[Categories]
Touch to display the category list.
•[Direct Tune]
Touch to display the keypad to enter the
frequency and directly tune to the channel.
SeeRadio operationearlier in this section
Display screen, heater and air conditioner, and audio system4-69

Page 265 of 531

Two USB (iPod) connectors are located on the
center console box.
USB (Universal Serial Bus) connection port/
iPod
The battery of the iPod will be charged while the
device is connected to the vehicle if the iPod
supports USB connection charging.
Depending on the model and firmware version
of the iPod, the display on the iPod shows an
INFINITI or Accessory Attached screen when the
connection is completed. When the iPod is
connected to the vehicle, the iPod music library
can only be operated using the vehicle audio
controls.
Compatibility
:
Made for
•iPod touchR(5th generation)
•iPod touchR(4th generation)
•iPod touchR(3rd generation)
•iPod touchR(2nd generation)
•iPod touchR(1st generation)
•iPod touchR
•iPodRwith video
•iPod classicR
•iPod nanoR(7th generation)
•iPod nanoR(6th generation)
•iPod nanoR(5th generation)
•iPod nanoR(4th generation)
•iPod nanoR(3rd generation)
•iPod nanoR(2nd generation)
•iPod nanoR(1st generation)
•iPhoneR6 Plus
•iPhoneR6
•iPhoneR5S
•iPhoneR5
•iPhoneR4S
•iPhoneR4
•iPhoneR3GS
•iPhoneR3G
•iPhoneR
The iPod touchRmay not respond quickly with
the system in some cases.
Make sure that the iPod
Rfirmware is up-
dated.The Lightning
TMconnector works with iPhone
R5, iPhoneR5S, iPhoneR6, iPhoneR6
Plus, iPod touch
R(5th generation), and iPod
nano
R(7th generation).
The 30-pin connector works with iPhone
R4S,
iPhone
R4, iPhoneR3GS, iPhoneR3G,
iPhone
R, iPod touchR(1st through 4th
generation), iPod classic
R, and iPod nanoR(1st through 6th generation).
USB works with iPhone
R5, iPhoneR4S,
iPhone
R4, iPhoneR3GS, iPhoneR3G,
iPhone
R, iPod touchR(1st through 5th
generation), iPod classi
Rc, and iPod nanoR(1st through 7th generation).
4-76Display screen, heater and air conditioner, and audio system

Page 268 of 531

Regulatory Information
FCC Regulatory information:
FCC ID : HYQDNNS075
NOTE: This device complies with part 15 of the
FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including in-
terference that may cause undesired operation.
FCC WARNING: Changes or modifications not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
CAUTION : Radio Frequency Radiation Exposure
This equipment complies with FCC radiation
exposure limits set forth for uncontrolled envi-
ronment and meets the FCC radio frequency (RF)
Exposure Guidelines. This equipment has very
low levels of RF energy that it deemed to comply
without maximum permissive exposure evalua-
tion (MPE). But it is desirable that it should be
installed and operated with at least 20cm and
more between the radiator and person’s body.
Co-location: This transmitter must not be co-
located or operated in conjunction with any
other antenna or transmitter.IC Regulatory information
:
The antenna cannot be removed (and changed)
by user.
NOTE: This device complies Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) This
device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired opera-
tion of the device.
CAUTION : Radio Frequency Radiation Exposure
This equipment complies with IC radiation ex-
posure limits set forth for uncontrolled environ-
ment and meets RSS-102 of the IC radio fre-
quency (RF) exposure rules. This equipment has
very low levels of RF energy that it deemed to
comply without maximum permissive exposure
evaluation (MPE). But it is desirable that it
should be installed and operated with at least
20cm and more between the radiator and per-
son’s body.
Co-location: This transmitter must not be co-
located or operated in conjunction with any
other antenna or transmitter.
This Class B digital apparatus meets all require-
ments of the Canadian Interference Causing
Equipment Regulations.
Connecting Bluetooth® streaming
audio device
Bluetooth® streaming audio device must be
connected to the vehicle before operation.
Connecting Bluetooth® device
Display screen, heater and air conditioner, and audio system4-79

Page 276 of 531

•Immediately after the ignition switch is
turned ON, it may be impossible to receive a
call for a short period of time.
•Do not place the cellular phone in an area
surrounded by metal or far away from the
in-vehicle phone module to prevent tone
quality degradation and wireless connection
disruption.
•While a cellular phone is connected through
the Bluetooth® wireless connection, the bat-
tery of the cellular phone may discharge
quicker than usual.
•If the Bluetooth® Hands-Free Phone System
seems to be malfunctioning, please visit
www.infinitiusa.com/bluetooth for trouble-
shooting help.
•Some cellular phones or other devices may
cause interference or a buzzing noise to be
emitted from the audio system speakers.
Storing the device in a different location may
reduce or eliminate the noise.
•Refer to the owner’s manual for the cellular
phone for information regarding the telephone
pairing procedure specific to your phone, bat-
tery charging, and cellular phone antenna, etc.
•The antenna display on the monitor may not
match the antenna display of some cellular
phones.
•The battery display on the monitor may not
match the battery display of some cellular
phones.
•Keep the interior of the vehicle as quiet as
possible to hear the caller’s voice clearly as
well as to minimize echoes.
•If reception between callers is unclear,
adjusting the incoming or outgoing call vol-
ume may improve the clarity.
REGULATORY INFORMATION
FCC Regulatory Information
FCC ID : HYQDNNS075
NOTE: This device complies with part 15 of the
FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including in-
terference that may cause undesired operation.
FCC WARNING: Changes or modifications not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
CAUTION : Radio Frequency Radiation Exposure
This equipment complies with FCC radiation
exposure limits set forth for uncontrolled envi-
ronment and meets the FCC radio frequency (RF)Exposure Guidelines. This equipment has very
low levels of RF energy that it deemed to comply
without maximum permissive exposure evalua-
tion (MPE). But it is desirable that it should be
installed and operated with at least 20cm and
more between the radiator and person’s body.
Co-location: This transmitter must not be co-
located or operated in conjunction with any
other antenna or transmitter.
IC Regulatory information
The antenna cannot be removed (and changed)
by user.
NOTE: This device complies Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) This
device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired opera-
tion of the device.
CAUTION : Radio Frequency Radiation Exposure
This equipment complies with IC radiation ex-
posure limits set forth for uncontrolled environ-
ment and meets RSS-102 of the IC radio fre-
quency (RF) exposure rules. This equipment has
very low levels of RF energy that it deemed to
comply without maximum permissive exposure
evaluation (MPE). But it is desirable that it
should be installed and operated with at least
Display screen, heater and air conditioner, and audio system4-87

Page 277 of 531

20cm and more between the radiator and per-
son’s body.
Co-location: This transmitter must not be co-
located or operated in conjunction with any
other antenna or transmitter.
This Class B digital apparatus meets all require-
ments of the Canadian Interference Causing
Equipment Regulations.
The Bluetooth® word mark and logos are reg-
istered trademarks owned by Bluetooth SIG,
Inc. and any use of such marks by DENSO
CORPORATION is under license. Other trade-
marks and trade names are those of their
respective owners.
PHONE
Connecting Bluetooth® Hands-Free
Phone
The cellular phone must be connected to the
Bluetooth® Hands-Free Phone System before
commencing operation. Up to 5 cellular phones
can be connected to the system.
SeeConnecting Bluetooth® devicelater in
this section
Phone selection
Select one of the connected devices for opera-
tion.
1. Push<MENU>and touch [Phone], then touch
[Select Phone]. A list of the connected cellu-
lar phones is displayed.
2. Select one of the connected cellular phones
from the list.
3. When selection of the device is successful,
a message on the display indicates that the
cellular phone was selected.
Making a call
1. Push<MENU>and touch [Phone].
2. Select one of the following methods to
make a call.
Available methods
•[Favorites]:
Select a telephone number from a list of
personally selected numbers.
•[Call History]:
Select a telephone number from recent
incoming or outgoing calls.
NAA1720
4-88Display screen, heater and air conditioner, and audio system

Page 304 of 531

Notes on operating audio by voice recognition:
•An audio device connected via Bluetooth®
cannot be operated with the Voice Recogni-
tion system. Source change is only available
for Bluetooth® streaming Audio.
•Song title and Artist name information will
be overwritten when another iPod
R/iPhone
Ris connected after song titles and artist
names in the previously connected iPod
R/
iPhon
Re have been installed.
•If two USB devices are connected at the same
time, voice operation will only be available for
use with one registered and selected device.When selecting “YES” in the pop-up screen that
displays after a new USB audio device is con-
nected, the USB audio device is registered in
the voice recognition system and is selected
automatically. One iPod and one USB device
can be registered in the system. If a USB audio
device is newly registered, old data is overwrit-
ten. It may take a few moments to register an
audio device. If you want to enable voice opera-
tion for music stored on a previously registered
audio device, select the device you want to use
in advance.
Voice recognition settingsin the5. Starting
and drivingsection
Even when a device has been previously
registered, simply connecting the device will
not result in it being selected automatically.
•The Voice Recognition system may not func-
tion when the song information is too long
(artist names, album titles, song titles and
playlists, etc.).
•The SXM function will not operate without a
subscription to SiriusXM Satellite Radio.
Information command
1st command 2nd command Action
Information Voice Menu Connects to the INFINITI InTouchTMServices Response Specialists. Refer to the Navigation Owner’s Manual for details.
Operator Connects to the INFINITI InTouchTMServices Response Specialists. Refer to the Navigation Owner’s Manual for details.
Where am I?* Displays the information of the current position.
Fuel Prices Displays the fuel prices.
Weather Forecast Displays the weather forecast.
Current Weather Displays the nearby weather (current weather).
Sports Scores Displays the sports scores.
Traffic Information* Turns the traffic information system on or off.
Route Information* Displays the route information.
*: Models with navigation system only.
Display screen, heater and air conditioner, and audio system4-115

Page:   < prev 1-10 11-20 21-30 31-40 41-50 51-60 61-70 71-80 ... 80 next >