battery INFINITI QX30 2018 Owner's Guide

Symptom Possible causeRemedy
You can no
longer lock or
unlock the
vehicle using
Intelligent KeyThe key
battery is
discharged
or nearly
discharged
•Check the key battery (see "Checking the battery") and replace it necessary
If this does not work:
•Unlock (see "Locking with the mechanical key" later in this section) or lock the vehicle using the emergency key element
There is inter-
ference from
a powerful
source of radio
waves
•Unlock (see "Locking with the mechanical key" later in this section) or lock the vehicle using the emergency key element
There is a fault
with the
Intelligent Key
system
•Lock/unlock the vehicle using the remote control function of the key.•Have the vehicle and key checked. It is recommended you visit an INFINITI retailer for this service.
If the vehicle can also not be locked/unlocked using the remote control function
•Unlock (see "Locking with the mechanical key" later in this section) or lock the vehicle using the emergency key element
•Have the vehicle and key checked. It is recommended you visit an INFINITI retailer for this service.
The engine
cannot be
started using
the keyThe on-board
voltage is too
low
•Switch off non-essential consumers, e. g. seat heating or interior lighting, and try to start the engine again
If this does not work:
•Check the starter battery and charge it if necessary (see "Battery")
or
•Jump-start the vehicle (see "Jump starting")
or
•Have the system checked. It is recommended you consult an INFINITI retailer.
Pre-driving checks and adjustments3-13

Symptom Possible causeRemedy
The engine
cannot be
started using
the push
button igni-
tion switch.
The key is in
the vehicleThe vehicle is
locked with the
Intelligent Key.
•Unlock the vehicle and try to start the vehicle again.
The key bat-
tery is weak or
discharged.
•Check the key battery (see "Checking the battery") and replace it necessary
If this does not work:
•Start your vehicle with the key in the ignition lock.
There is inter-
ference from
a powerful
source of radio
waves.
•Start the vehicle with the key in the ignition lock.
You have lost
a key—
•Have the key deactivated. It is recommended you visit an INFINITI retailer for this service.•Report the loss immediately to the vehicle insurers•If necessary, have the locks changed as well
You have lost
the emer-
gency key
element
•Report the loss immediately to the vehicle insurers•If necessary, have the locks changed as well.
3-14Pre-driving checks and adjustments

Refer to the INFINITI InTouch Owner’s
Manual, that includes the following informa-
tion:
•Center multi-function control panel and
steering wheel switch
•Audio system
•Bluetooth® Hands-Free Phone system
•INFINITI InTouch Apps
•INFINITI InTouch™ Services (if equipped)
•Sirius XM Travel Link
•Sirius XM Travel
•Navigation system (where fitted)
•Voice recognition
•Information and settings viewable on
INFINITI InTouch
WARNING
•Do not adjust the heater and air condi-
tioner controls or audio controls while
driving so that full attention may be
given to vehicle operation.
•Do not use this system if you notice any
abnormality, such as a frozen screen or
lack of sound. Continued use of the sys-
tem may result in accident, fire or elec-
tric shock.
•If you noticed any foreign objects enter-
ing the system hardware, spilled liquid
on the system, or noticed smoke or
fumes coming out from the system, or
any other unusual operation is ob-
served, stop using the system immedi-
ately. It is recommended that you con-
tact the nearest INFINITI retailer.
Ignoring such conditions may lead to an
accident, fire or electric shock.
•Do not disassemble or modify this sys-
tem. If you do, it may lead to an accident,
fire, or electric shock.
•Park the vehicle in a safe location and
apply the parking brake to view the im-
ages on the front center display screen.
CAUTION
•Do not use the system when the engine
is not running for extended periods of
time to prevent battery discharge.
•Do not attempt to operate the system in
extreme temperature conditions [below
−4°F (−20°C) and above 158°F (70°C)].
Operating this system under these condi-
tions may result in system malfunctions.
INFINITI INTOUCH OWNER'S
MANUALSAFETY PRECAUTIONS
4-2Display screen, heater and air conditioner, and audio system

Backing up near a projecting object
The predicted course linesAdo not touch
the object in the display. However, the vehicle
may hit the object if it projects over the actual
moving course.
Backing up behind a projecting
object
The positionCis shown further than the
position
Bin the display. However, the po-
sition
Cis actually at the same distance asthe position
A.The vehicle may hit the object
when backing up to the position
Aif the
object projects over the actual moving course.
HOW TO PARK WITH
PREDICTED COURSE LINES
WARNING
•If the tires are replaced with different
sized tires, the predicted course line may
not be displayed correctly.
•On a snow-covered or slippery road,
there may be a difference between the
predicted course line and the actual
course line.
•The displayed lines will appear slightly
off to the right because the rear view
camera is not installed in the rear center
of the vehicle.
•If the battery is disconnected or be-
comes discharged, the predicted course
lines may be displayed incorrectly. If this
occurs, please perform the following
procedures:
–Turn the steering wheel from lock to
lock while the engine is running.
–Drive the vehicle on a straight road
for more than 5 minutes.
SAA1923SAA1980
4-6Display screen, heater and air conditioner, and audio system

Backing up behind a projecting
object
The positionCis shown farther than the
position
Bin the display. However, the po-
sition
Cis actually at the same distance asthe position
A. The vehicle may hit the object
when backing up to the position
Aif the
object projects over the actual moving course.
HOW TO PARK WITH
PREDICTED COURSE LINES
WARNING
•If the tires are replaced with different
sized tires, the predicted course lines
may not be displayed correctly.
•On a snow-covered or slippery road,
there may be a difference between the
predicted course lines and the actual
course.
•The displayed lines will appear slightly
off to the right because the rear view
camera is not installed in the rear center
of the vehicle.
•If the battery is disconnected or be-
comes discharged, the predicted course
lines may be displayed incorrectly. If this
occurs, please perform the following
procedures:
–Turn the steering wheel from lock to
lock while the engine is running.
–Drive the vehicle on a straight road
for more than 5 minutes.
•When the steering wheel is turned with
the ignition switch in the ACC position,
the predicted course lines may be dis-
played incorrectly.
SAA1980
Display screen, heater and air conditioner, and audio system4-17

Cold weather driving...................5-96
Freeing a frozen door lock.............5-96
Antifreeze........................5-96
Battery..........................5-96Draining of engine coolant.............5-96
Tire equipment.....................5-96
Special winter equipment..............5-97
Driving on snow or ice................5-97

The INFINITI Vehicle Immobilizer System will
not allow the engine to start without the use
of the registered key.
If the engine fails to start using the registered
key, it may be due to interference caused by
another registered key, an automated toll
road device or automated payment device on
the key ring. Restart the engine using the
following procedures:
1. Leave the ignition switch in the ON posi-
tion for approximately 5 seconds.
2. Turn the ignition switch to the OFF or
LOCK position and wait approximately
5 seconds.
3. Repeat Step 1 and 2 again.
4. Restart the engine while holding the de-
vice (which may have caused the interfer-
ence) separate from the registered key.
If the no start condition re-occurs, INFINITI
recommends placing the registered key on a
separate key ring to avoid interference from
other devices.
0OFF position
1ACC position
2ON position
3START position
WARNING
Never remove the key or turn the ignition
switch to the OFF position while driving.
The steering wheel will lock and could
cause the driver to lose control of the ve-
hicle. This could result in serious vehicle
damage or personal injury.
CAUTION
Use electrical accessories with the engine
running to avoid discharging the vehicle
battery. If you must use accessories while
the engine is not running, do not use them
for extended periods of time and do not use
multiple electrical accessories at the same
time.
KEY POSITIONS
OFF (Normal parking position)
0
The ignition key can only be removed when in
this position.
The steering lock can only be locked in this
position.
ACC (Accessories)/1
The engine is turned off without locking the
steering wheel. This position activates elec-
trical accessories, such as the radio, when the
engine is not running.
ON (Normal operating position)2
This position turns on the ignition system and
electrical accessories.
NPA1483
INFINITI VEHICLE IMMOBILIZER
SYSTEMIGNITION SWITCH
Starting and driving5-13

START3
The engine starter activates and the engine
will start. As soon as the engine has started,
release the key immediately. It will return to
the ON position.
NOTE
For vehicles fitted with Idle Stop/Start Sys-
tem:
When the engine is automatically stopped
by the Idle Stop/Start System the ignition
switch can still be operated as usual.
At the end of a journey turn the ignition OFF
to avoid a discharged battery. The Idle
Stop/Start System does not automatically
turn ignition off.
Vehicles with Intelligent Key are equipped with
keys featuring an integrated Intelligent Key
function and in some cases a detachable push-
button ignition switch (Start/Stop button).
A check which periodically establishes a radio
connection between the vehicle and the key
determines whether a valid key is in the ve-
hicle. This occurs, for example, when starting
the engine.
When you insert the push-button ignition
switch into the ignition lock, the system needs
approximately two seconds recognition time.
You can then use the push-button ignition
switch.
WARNING
Do not operate the push-button ignition
switch while driving the vehicle except in
an emergency. (The engine will stop when
the ignition switch is pressed 3 consecutive
times in quick succession or the ignition
switch is pushed and held for more than 2
seconds.) If the engine stops while the ve-
hicle is being driven, this could lead to a
crash and serious injury.
Before operating the push-button ignition
switch:
•Select P (Park).Pressing the Start/Stop button several times
in succession corresponds to the different
key positions in the ignition lock. Prerequisite
for this is that:
•You do not depress the brake pedal.
If you depress the brake pedal and press the
Start/Stop button, the engine starts immedi-
ately.
To start the vehicle without actively using the
key:
•The push-button ignition switch must be
inserted in the ignition lock.
•The key must be in the vehicle.
•The vehicle must not be locked with the
key or Intelligent Key (see "Keys").
Do not keep the Intelligent Key:
•With electronic devices, for example a mo-
bile phone or another key.
•With metallic objects, for example coins or
metal film.
•Inside metallic objects, for example a metal
case.
This can affect the functionality of the Intel-
ligent Key.
PUSH-BUTTON IGNITION SWITCH
(IF EQUIPPED)
5-14Starting and driving

3. Turn the key to the START position3in
the ignition lock and release it as soon as
the engine is running.
If the engine is very hard to start because it is
flooded, depress the accelerator pedal all the
way to the floor and hold it. Turn the ignition
switch to the START position to start crank-
ing the engine. After 5 or 6 seconds, stop
cranking by turning the ignition switch to
OFF. After cranking the engine, release the
accelerator pedal. Crank the engine with your
foot off the accelerator pedal by depressing
the brake pedal and turning the ignition
switch to start the engine. If the engine starts,
but fails to run, repeat the above procedure.
CAUTION
Do not operate the starter for more than
15 seconds at a time. If the engine does not
start, turn the ignition key to the OFF po-
sition and wait 10 seconds before cranking
again, otherwise the starter could be
damaged.4.Warm-up
Allow the engine to idle for at least 30
seconds after starting. Do not race the
engine while warming it up. Drive at mod-
erate speed for a short distance first, es-
pecially in cold weather. In cold weather,
keep the engine running for a minimum of
2 - 3 minutes before shutting it off. Start-
ing and stopping the engine over a short
period of time may make the vehicle more
difficult to start.
5. To stop the engine, Shift the transmission
to position P (Park) by pressing the <P>
button. and turn the ignition switch to the
OFF position.
NOTE
Care should be taken to avoid situations
that can lead to potential battery discharge
and potential no-start conditions such as:
•Installation or extended use of electronic
accessories that consume battery power
when the engine is not running (Phone
chargers, GPS, DVD players, etc.)
•Vehicle is not driven regularly and/or only
driven short distances. In these cases, the
battery may need to be charged to main-
tain battery health.
STARTING PROCEDURE USING
THE PUSH-BUTTON IGNITION
SWITCH (IF EQUIPPED)
The push-button ignition switch can be used
to start the vehicle manually without insert-
ing the key into the ignition lock. The key must
be in the vehicle and the start/stop button
must be inserted in the ignition lock (see &#34;Re-
moving the start/stop button&#34; earlier in this
section). This mode for starting the engine
operates independently of the ECO start/
stop automatic engine start function.
You can start the engine if a valid key is in the
vehicle. Switch off the engine and always
take the key with you when leaving the ve-
hicle, even if you only leave it for a short time.
Pay attention to the important safety notes.
•Depress the brake pedal and keep it de-
pressed.
•Press the push button ignition switch once
(see &#34; Push-button ignition switch (if
equipped)&#34; earlier in this section). The en-
gine starts.
Starting and driving5-17

The Idle Stop/Start function switches the
engine off automatically if the vehicle is
stopped under certain conditions.
When pulling away again, the engine starts
automatically. The Idle Stop/Start function
thereby helps you to reduce the fuel con-
sumption and emissions of your vehicle.
WARNING
If the engine is switched off automatically
and you exit the vehicle, the engine is re-
started automatically. The vehicle may be-
gin moving There is a risk of accident and
injury.
If you wish to exit the vehicle, always turn
off the ignition and secure the vehicle
against rolling away.If the
Idle Stop/Start symbol is shown
in green in the vehicle information display,
the Idle Stop/Start function switches the
engine off automatically once the vehicle
stops moving.
The Idle Stop/Start function is automatically
activated each time you start the engine with
the ignition key.
If the Idle Stop/Start function has been manu-
ally deactivated (see&#34;Deactivating/activating
the Idle Stop/Start function&#34; later in this sec-
tion) or a malfunction has caused the system
to be deactivated, the
Idle Stop/Start
symbol is not displayed.
AUTOMATIC ENGINE
SWITCH-OFF
The Idle Stop/Start function is operational
and theIdle Stop/Start symbol is dis-
played in green in the vehicle information dis-
play, if:
•The indicator light in the ECO button is lit
green.
•The outside temperature is within the
range that is suitable for the system.
•The engine is at normal operating tem-
perature.
•The set temperature for the vehicle interior
has been reached.
•The battery is sufficiently charged.
•The system detects that the windshield is
not misted up when the air-conditioning
system is switched on.
•The hood is closed.
•The driver&#39;s door is closed and the driver&#39;s
seat belt is fastened.
If the conditions for automatic engine
switch-off are not all fulfilled, the
Idle
Stop/Start symbol is shown in yellow.
NSD620
Idle Stop/Start symbol
IDLE STOP/START SYSTEM (IF
EQUIPPED)
Starting and driving5-29