display INFINITI QX30 2018 Manual PDF

The bird's-eye view shows the overhead view
of the vehicle, which helps confirm the vehicle
position.
The vehicle icon
1shows the position of the
vehicle.
NOTE
The size of the vehicle icon on the bird's-eye
view may differ somewhat from the actual
vehicle.
The areas that the cameras cannot cover
2are indicated in black.
The non-viewable area
2is highlighted in
yellow for several seconds after the bird's-
eye view is displayed. It will be shown only the
first time after the ignition switch is placed in
the ON position.
When the corner of the vehicle moves closer
to an object, the corner sensor indicator
3appears.Front-side view:
Guiding lines that indicate the approximate
width and the front end of the vehicle are
displayed on the monitor.
The front-of-vehicle line
1shows the front
part of the vehicle.
The side-of-vehicle line
2shows the ap-
proximate vehicle width including the outside
mirrors.
The extensions
3of both the front1and
side
2lines are shown with a green dotted
line.
The corner sensor indicator
4will appear
when a corner of the vehicle moves closer to
an object.
DIFFERENCE BETWEEN
PREDICTED AND ACTUAL
DISTANCES
The displayed guidelines and their locations
on the ground are for approximate reference
only. Objects on uphill or downhill surfaces or
projecting objects will be actually located at
distances different from those displayed in
the monitor relative to the guidelines (refer to
illustrations). When in doubt, turn around and
view the objects as you are backing up, or
park and exit the vehicle to view the position-
ing of objects behind the vehicle.
NAA1681SAA1842Z
Left-Hand Drive (LHD) models*
Display screen, heater and air conditioner, and audio system4-15

Backing up on a steep uphill
When backing up the vehicle up a hill, the
distance guide lines and the vehicle width
guide lines are shown closer than the actual
distance. Note that any object on the hill is
viewed in the monitor farther than it appears.
Backing up on a steep downhill
When backing up the vehicle down a hill, the
distance guide lines and the vehicle width
guide lines are shown farther than the actual
distance. Note that any object on the hill is
viewed in the monitor closer than it appears.
Backing up near a projecting object
The predicted course linesAdo not touch
the object in the display. However, the vehicle
may hit the object if it projects over the actual
moving course.
NAA1675NAA1676SAA1923
4-16Display screen, heater and air conditioner, and audio system

Backing up behind a projecting
object
The positionCis shown farther than the
position
Bin the display. However, the po-
sition
Cis actually at the same distance asthe position
A. The vehicle may hit the object
when backing up to the position
Aif the
object projects over the actual moving course.
HOW TO PARK WITH
PREDICTED COURSE LINES
WARNING
•If the tires are replaced with different
sized tires, the predicted course lines
may not be displayed correctly.
•On a snow-covered or slippery road,
there may be a difference between the
predicted course lines and the actual
course.
•The displayed lines will appear slightly
off to the right because the rear view
camera is not installed in the rear center
of the vehicle.
•If the battery is disconnected or be-
comes discharged, the predicted course
lines may be displayed incorrectly. If this
occurs, please perform the following
procedures:
–Turn the steering wheel from lock to
lock while the engine is running.
–Drive the vehicle on a straight road
for more than 5 minutes.
•When the steering wheel is turned with
the ignition switch in the ACC position,
the predicted course lines may be dis-
played incorrectly.
SAA1980
Display screen, heater and air conditioner, and audio system4-17

The vehicle width and predicted course lines
are wider than the actual width and course.
1. Visually check that the parking space is
safe before parking your vehicle.2. The rear view of the vehicle is displayed on
the screen
Aas illustrated when the shift
lever is moved to the R (Reverse) position.
When activating the Around View®
Monitor, the icons and the messages may
not be displayed immediately.
3. Slowly back up the vehicle adjusting the
steering wheel so that the predicted
course lines
Benter the parking space
C.
SAA1897SAA1898
4-18Display screen, heater and air conditioner, and audio system

4. When the rear of the vehicle enters the
parking space
C, maneuver the steering
wheel to make the vehicle width guide
lines
Dparallel to the parking spaceC.
5. When the vehicle is parked in the space
completely, press the P (Park) button and
apply the parking brake.
HOW TO SWITCH THE DISPLAY
The view on the Around View® Monitor
screen can be switched by pressing the
<CAMERA>button or by changing the shift
lever position.
Press the<CAMERA>button:
When the<CAMERA>button is pushed while
a screen other than a camera screen is dis-
played, the Around View® Monitor operates
and the front view and bird&#39;s-eye view are
displayed. Push the<CAMERA>button to
switch the display to the front view and
front-side view screen.
ADJUSTING THE SCREEN
1. Push the<MENU>buttonBon the
INFINITI Controller and touch [Settings]
Ain the vehicle information display.
2. Touch [Camera]/[Sonar]
3. Touch [Display]
4. Select the item you wish to adjust:
[Brightness]:
Adjust display settings by touching [+]/[-].
[Contrast]:
Adjust display settings by touching [+]/[-].
[Black level]:
Adjust display settings by touching [+]/[-].
[Tint]:
Adjust display settings by touching [+]/[-].
[Color]:
Adjust display settings by touching [+]/[-].
[Reset Settings]:
Return all the settings to defaultNOTE
Do not adjust any of the display settings of
the Around View® Monitor while the vehicle
is moving. Make sure the parking brake is
firmly applied.
Display screen, heater and air conditioner, and audio system4-19

A[Settings] key
B<MENU> button
AROUND VIEW® MONITOR
SETTING
Around View® Monitor settings can be
changed using the following procedure:1. Push the<MENU>button
Bon the
INFINITI Controller and touch [Settings]
Ain the vehicle information display.
2. Touch [Camera]/[Sonar]
3. Touch [Camera]
4. Touch [Moving Object Detection]
Activate or deactivate the Moving Object
Detection (MOD) mode.
AROUND VIEW® MONITOR
SYSTEM LIMITATIONS
WARNING
Listed below are the system limitations for
Around View® Monitor. Failure to operate
the vehicle in accordance with these sys-
tem limitations could result in serious in-
jury or death.
•Do not use the Around View® Monitor
with the outside mirror in the stored po-
sition, and make sure that the lift gate is
securely closed when operating the ve-
hicle using the Around View® Monitor.
•The apparent distance between objects
viewed on the Around View® Monitor
differs from the actual distance.
NSD628
4-20Display screen, heater and air conditioner, and audio system

•The cameras are installed on the front
grille, the outside mirrors and above the
rear license plate. Do not put anything
on the cameras.
•When washing the vehicle with high-
pressure water, be sure not to spray it
around the cameras. Otherwise, water
may enter the camera unit causing wa-
ter condensation on the lens, a malfunc-
tion, fire or an electric shock.
•Do not strike the cameras. They are pre-
cision instruments. Doing so could cause
a malfunction or cause damage resulting
in a fire or an electric shock.
The following are operating limitations and
do not represent a system malfunction:
•There may be a delay when switching be-
tween views.
•When the temperature is extremely high or
low, the screen may not display objects
clearly.
•When strong light is directly shines on the
camera, objects may not be displayed
clearly.
•The screen may flicker under fluorescent
light.
•The colors of objects on the Around
View® Monitor may differ somewhat
from the actual color of objects.
•Objects on the monitor may not be clear
and the color of the object may differ in a
dark environment.
•There may be differences in sharpness be-
tween each camera view of the bird’s-eye
view.
•Do not use wax on the camera lens. Wipe
off any wax with a clean cloth that has
been dampened with a diluted mild clean-
ing agent, then wipe with a dry cloth.
There are some areas where the system will not
show objects and the system does not warn of
moving objects. When in the front or the rear
view display, an object below the bumper or on
the ground may not be viewed
1. When in the
bird&#39;s-eye view, a tall object near the seam
3of the camera viewing areas will not appear
in the monitor
2.
NAA1639
Display screen, heater and air conditioner, and audio system4-21

System temporarily unavailable
When the [!] icon is displayed on the screen,
there are abnormal conditions in the Around
View® Monitor. This will not hinder normal
driving operation but the system should be
inspected. It is recommended you visit an
INFINITI retailer for this service.When the [X] icon is displayed on the screen,
the camera image may be receiving tempo-
rary electronic disturbances from surround-
ing devices. This will not hinder normal driving
operation but the system should be in-
spected. It is recommended you visit an
INFINITI retailer for this service.
SYSTEM MAINTENANCE
CAUTION
•Do not use alcohol, benzine or thinner to
clean the camera. This will cause discol-
oration. To clean the camera, wipe with
a cloth dampened with diluted mild
cleaning agent and then wipe with a dry
cloth.
•Do not damage the camera as the moni-
tor screen may be adversely affected.
If dirt, rain or snow accumulates on any of the
cameras, the Around View® Monitor may
not display objects clearly. Clean the cameras
by wiping with a cloth dampened with a di-
luted mild cleaning agent and then wiping
with a dry cloth.
NAA1779NAA1780NAA1638
4-22Display screen, heater and air conditioner, and audio system

A[Settings] key
B<MENU> button
SONAR FUNCTION SETTINGS
(IF SO EQUIPPED)
The sonar function settings can be changed
using the following procedure.1. Push<MENU>
Band touch [Settings]A.
2. Touch [Camera/Sonar]
3. Touch [Sonar]
[Sonar sensitivity]:
Adjust the sonar sensor sensitivity level by
touching [+]/[-].
[Sonar volume]:
Adjust the buzzer volume by touching [+]/[-].
NSD628
Display screen, heater and air conditioner, and audio system4-23

AAround View Monitor display
BINFINITI controller
C<MENU> button
D<CAMERA> button
WARNING
Failure to follow the warnings and instruc-
tions for proper use of the Moving Object
Detection system could result in serious in-
jury or death.
•The MOD system is not a substitute for
proper vehicle operation and is not de-
signed to prevent contact with objects
surrounding the vehicle. When maneu-
vering, always use the outside mirror
and rearview mirror and turn and check
the surroundings to ensure it is safe to
maneuver.
•The system is deactivated at speeds
above 5 MPH (8 km/h). It is reactivated
at lower speeds.
•The MOD system is not designed to de-
tect the surrounding stationary objects.
The Moving Object Detection (MOD) system
can inform the driver of moving objects
surrounding the vehicle when driving out of
garages, maneuvering into parking lots and in
other such instances.
The MOD system detects moving objects by
using image processing technology on the
image shown on the display.
NSD651
MOVING OBJECT DETECTION (IF SO
EQUIPPED)
4-24Display screen, heater and air conditioner, and audio system