engine INFINITI QX30 2018 Owners Manual

If not all conditions for automatic engine
switch-off are met, theIdle Stop/
Start symbol is lit yellow in the vehicle
information display. If this is the case, the
Idle Stop/Start function is not active.
If indicator light
2on ECO button1is off,
the Idle Stop/Start function has been deacti-
vated manually or as the result of a malfunc-
tion. The engine will then not be switched off
automatically when the vehicle stops.
WARNING
Failure to follow the warnings and instruc-
tions for proper use of the LDW system
could result in serious personal injury or
death. The LDW system will not steer the
vehicle or prevent loss of control. It is the
driver’s responsibility to stay alert, drive
safely, keep the vehicle in the traveling
lane, and be in control of the vehicle at all
times.
The LDW system warns the driver with a
warning light and intermittent steering vibra-
tion that the vehicle is beginning to leave the
traveling lane. The LDW system uses a camera
1installed
behind the windshield to monitor the lane
markers of your traveling lane.
NSD644
LANE DEPARTURE WARNING (LDW)
SYSTEM (IF EQUIPPED)
Starting and driving5-31

1Steering wheel mounted controls
2Vehicle information display
ADisplay area
BMenu bar
LDW SYSTEM TEMPORARILY
UNAVAILABLE
Under the following conditions, the LDW
system will be canceled automatically, and
the message [Lane Departure Warning Cur-
rently Unavailable See Operator's Manual] isdisplayed in the vehicle information display
2. The LDW system is temporarily unavail-
able.
•The windshield is dirty in the camera's field
of vision.
•Visibility is impaired due to heavy rain,
snow or fog.
•There have been no lane markings for an
extended period.
•The lane markings are worn, dark, or cov-
ered by dirt or snow, etc.
Action to take: When the above conditions
no longer exist, the message goes out and the
LDW system is operational again. If the mes-
sage continues to appear, stop the vehicle in
a safe location, press the P (Park) button , and
clean the windshield.
SYSTEM MALFUNCTION
If the LDW system malfunctions, it will cancel
automatically, and the message [Lane De-
parture Warning Inoperative] will appear.
Action to take: Stop the vehicle in a safe
location, engage P (Park), turn the engine off
and restart the engine. If the message contin-
ues to appear, have the system checked. It is
recommended you visit an INFINITI retailer
for this service.
NSD626
Starting and driving5-35

SYSTEM TEMPORARILY
UNAVAILABLE
1Vehicle information display
If radar blockage is detected, the system will
be turned off automatically, and the [Blind Spot Warning Currently Unavailable See Op-
erator's Manual] message appears in the ve-
hicle information display1. The system is
not available until the conditions no longer
exist. The radar sensors may be blocked by tempo-
rary ambient conditions such as splashing
water, mist or fog. The blocked condition
may also be caused by objects such as ice,
frost or dirt obstructing the radar sensors.
Action to take:
When the above conditions
no longer exist, the system will resume auto-
matically. If the message still appears, have
the system checked. It is recommended you
visit an INFINITI retailer for this service.
System malfunction
If the system malfunctions, it will be turned
off automatically, and the [Blind Spot Warn-
ing Inoperative] message appears in the ve-
hicle information display
1.
Action to take: Stop the vehicle in a safe
location, place the vehicle in the P (Park) po-
sition, turn the engine off and restart the
engine.
If the message still appears, have the system
checked. It is recommended you visit an
INFINITI retailer for this service.
NSD631
Starting and driving5-45

NOTE
Cruise control may be unable to maintain the
stored speed on uphill gradients. The stored
speed is resumed when the gradient evens
out. Cruise control maintains the stored
speed on downhill gradients by automati-
cally braking the vehicle.
Storing the current speed or calling up the
last stored speed:
WARNING
If you call up a stored speed and this is
different from the current speed, the ve-
hicle accelerates or brakes. If you do not
know what the stored speed is, the vehicle
may accelerate or brake unexpectedly.
There is a risk of an accident.
Take the traffic conditions into account
before calling up the stored speed. If you do
not know what the stored speed is, store
the desired speed again.
1. Briefly pull the cruise control lever to- wards you
2.
2. Remove your foot from the accelerator pedal. The first time cruise control is acti-
vated, it stores the current speed or if a
speed has previously been stored, it regu-
lates the speed of the vehicle to the pre-
viously stored speed.
Setting a speed
Bear in mind that it may take a brief moment
until the vehicle has accelerated or braked to
the set speed.
1. Press the cruise control lever up
1for a
higher speed or down
3for a lower
speed.
2. Keep the cruise control lever pressed until the desired speed is reached.
3. Release the cruise control lever, The new speed is stored.
4. To adjust the set speed in 1 MPH (1 km/h) increments: briefly press the cruise control
lever up
1or down3to the pressure
point. The last stored speed increases or
decreases in 1 MPH (1 km/h) increments.
5. To adjust the set speed in 10 MPH (10 km/h) increments: briefly press the cruise
control lever up
1or down3beyond the
pressure point. The last stored speed in-
creases or decreases in 10 MPH
(10 km/h) increments.
NOTE
Cruise control is not deactivated if you de-
press the accelerator pedal. For example, if
you accelerate briefly to overtake, cruise
control adjusts the vehicle's speed to the last
speed stored after you have finished over-
taking.
Deactivating cruise control
There are several ways to deactivate cruise
control:
•Briefly press the cruise control lever for-
ward
4.
or
•Brake.
Cruise control is automatically deactivated if:
•The vehicle is secured with the electric
parking brake.
•You are driving at less than 20 MPH (30
km/h).
•VDC intervenes or you deactivate VDC.
If cruise control is deactivated, you will hear a
warning tone. You will see the [Cruise Control
Off] message in the vehicle information dis-
play for approximately five seconds.
NOTE
The last speed stored is cleared when you
switch off the engine.
5-48Starting and driving

[ICC Currently Unavailable See Operator's
Manual]:The ICC system is temporarily inop-
erative. Possible causes:
•The function is impaired due to heavy rain
or snow.
•The radar sensor system is temporarily in-
operative, e. g. due to electromagnetic ra-
diation emitted by nearby TV or radio sta-
tions or other sources of electromagnetic
radiation.
•The system is outside the operating tem-
perature range.
•The on-board voltage is too low.
A warning tone also sounds.
Once the causes listed above no longer apply,
the display message goes out.
If the display message does not disappear:
•Pull over and stop the vehicle safely as
soon as possible, paying attention to road
and traffic conditions.
•Secure the vehicle against rolling away.
•Restart the engine. [ICC Inoperative]:
The ICC system is mal-
functioning. The adaptive brake assist func-
tion may also have failed. A warning tone also
sounds. Have the system checked. It is rec-
ommended you visit an INFINITI retailer for
this service.
[ICC Suspended]: You have depressed the
accelerator pedal. The ICC system is no lon-
ger controlling the speed of the vehicle.
The display message should disappear when
you remove your foot from the accelerator
pedal
[ICC–––MPH]: An activation condition for
the ICC system is not fulfilled.
Check the activation conditions for the ICC
system.
SYSTEM MAINTENANCE
The sensor for the ICC systemAis located
behind the INFINITI logo at the front of the
vehicle.
To keep the ICC system operating properly,
be sure to observe the following:
•Always keep area around the sensor clean.
•Do not strike or damage the areas around
the sensor. Do not touch or remove the
screw located on the sensor. Doing so
could cause failure or malfunction. If the
sensor is damaged due to an accident, it is
recommended you contact an INFINITI re-
tailer.
•Do not cover or attach stickers (including
transparent material) or install an acces-
sory near the sensor. This could cause fail-
ure or malfunction.
NSD645
5-62Starting and driving

Use the following procedure to turn the FEB
system on or off:
1. Press the
<or>button on the
steering wheel
1to select the [DriveAs-
sist] menu on the Menu bar
B.
2. Press the
orbutton to select
[Emergency Brake].
3. Press the <OK>button on the steering
wheel
1. The current selection is dis-
played.
4. To activate/deactivate the FEB system: press the <OK>button again
When the FEB system is deactivated, the
symbolCappears in the vehicle infor-
mation display. NOTE
The FEB system will be automatically turned
on when the engine is restarted.
FEB SYSTEM LIMITATIONS
WARNING
Listed below are the system limitations for
the FEB system. Failure to operate the ve-
hicle in accordance with these system limi-
tations could result in serious injury or
death.
•The FEB system cannot detect all ve-
hicles under all conditions.
•The radar sensor does not detect the
following objects: – Pedestrians or animals
– Oncoming vehicles
– Crossing vehicles
•The radar sensor has some performance
limitations. For stationary vehicles, the
FEB system will not function when the
vehicle is driven at speeds over: –
Approximately 31 MPH (50 km/h) for
the Autonomous braking function.
•The radar sensor may not detect a ve-
hicle ahead in the following conditions: – Dirt, ice, snow or other material cov-
ering the radar sensor. –
Interference by other radar sources.
– Snow or heavy rain.
– If the vehicle ahead is narrow (e.g.
motorcycle).
– If the vehicle ahead is in a different
lane.
– Under strong radar reflections, for
example, in a multi-level parking ga-
rage.
– New vehicle or after a maintenance
of the FEB system. For additional in-
formation, see &#34;Break-in schedule&#34;
later in this section
– When driving on a steep downhill
slope or roads with sharp curves.
– When towing a trailer.
•In some road or traffic conditions, the
FEB system may intervene unnecessar-
ily or give an unnecessary warning. Al-
ways pay careful attention to the traffic
situation. Do not rely solely on the dis-
tance warning function and terminate
the intervention if necessary.
•Braking distances increase on slippery
surfaces.
NSD630
Starting and driving5-67

•The system is designed to automatically
check the sensor’s functionality, within
certain limitations. The system may not
detect some forms of obstruction of the
sensor area such as ice, snow, stickers,
for example. In these cases, the system
may not be able to warn the driver prop-
erly. Be sure that you check, clean and
clear the sensor area regularly.
•Excessive noise will interfere with the
warning chime sound, and the chime
may not be heard.
SYSTEM TEMPORARILY
UNAVAILABLE
If the FEB stops working due to a malfunc-
tion or some other reason, one of the follow-
ing three messages will be displayed in the
vehicle information display.
•[Emergency Brake Currently Unavailable
See Operator&#39;s Manual]
•[Emergency Brake Inoperative]
•[Radar Sensors Dirty See Operator&#39;s
Manual]
For each of these messages, possible causes
and solutions are listed below. [Emergency Brake Currently Unavailable
See Operator&#39;s Manual]:
The FEB system is
temporarily inoperative. Possible causes:
•The radar sensor system is temporarily in-
operative, for example, due to electro-
magnetic radiation emitted by nearby TV
or radio stations or other sources of elec-
tromagnetic radiation.
•The system is outside the operating tem-
perature range.
•The on-board voltage is too low.
Once the causes listed above no longer apply,
the display message goes out. The FEB sys-
tem is operative again.
If the display message does not disappear:
•Pull over and stop the vehicle safely as
soon as possible, paying attention to road
and traffic conditions.
•Secure the vehicle against rolling away.
•Switch off the engine.
[Emergency Brake Inoperative]: The FEB
system is temporarily inoperative due to a
malfunction. The adaptive brake assist func-
tion may also have failed.
It is recommended you visit an INFINITI re-
tailer. [Radar Sensors Dirty See Operator&#39;s
Manual]:
The FEB system is temporarily re-
stricted or inoperative. Possible causes:
•The sensor behind the INFINITI logo is
dirty.
•The function of the FEB system is im-
paired due to heavy rain or snow.
A warning tone also sounds.
Once the causes listed above no longer apply,
the display message goes out. The FEB sys-
tem is operative again.
If the display message does not disappear:
•Pull over and stop the vehicle safely as
soon as possible, paying attention to road
and traffic conditions.
•Secure the vehicle against rolling away.
•Switch off the engine.
•Clean the area around the sensors.
•Restart the engine. The display message
disappears.
5-68Starting and driving

NOTE
To operate the active sound enhancement
properly:
•Do not cover the speakers or woofer.
•Do not change or modify speakers includ-
ing the woofer and any audio related parts
such as the amplifier.
•Do not make any modification including
sound deadening or modifications around
the speakers or woofer.
ACTIVE SOUND ENHANCEMENT
The active sound enhancement generates
sounds according to engine speed through
the speakers
2and woofer1(if equipped)
to enhance the quality of the engine sound.
NSD648
ACTIVE SOUND ENHANCEMENT
5-70Starting and driving

•The border of the parking space must not
be too wide, as the position of the vehicle
must not exceed an angle of 45 degrees to
the starting position as it is manoeuvred
into the parking space.
•A total front and back maneuvering dis-
tance of at least 1.0 m must be available.
IPA can only assist you with exiting a parking
space if you have parked the vehicle parallel
to the direction of travel using IPA.
WARNING
•IPA is only an aid. It is not a substitute
for your attention to the immediate sur-
roundings. The responsibility for safe
maneuvering and parking remains with
you.
•Make sure that no persons, animals or
objects are in the maneuvering range.
•When the sonar function is deactivated,
IPA is also unavailable.
•While parking or pulling out of a parking
space, the vehicle swings out and can
drive onto areas of the oncoming lane.
This could cause you to collide with
other road users. There is a risk of an
accident.
•Pay attention to other road users. Stop
the vehicle if necessary or cancel the IPA
parking procedure.
1. Start the engine.
2. Release the electric parking brake.
3. Switch on the turn signal in the direction you are pulling away.
4. Vehicles with automatic transmission:
shift the transmission to position D or R
The [Start Park Assist? Yes: OK No:]
message appears in the vehicle informa-
tion display.
5. To cancel the procedure: press the
button on the steering wheel or pull away
or
6. To exit a parking space using IPA: press the <OK> button on the steering wheel
The Park Assist [Observe surroundings]
message appears in the display.
7. Release the steering wheel.
8. Pull away, being ready to brake at all times Do not exceed a maximum speed of
approximately 5 MPH (10 km/h) when
exiting a parking space. Otherwise, IPA
will be canceled.
WARNING
While parking or pulling out of a parking
space, the vehicle swings out and can drive
onto areas of the oncoming lane. This could
cause you to collide with other road users.
There is a risk of an accident.
9. Depending on the message or as required, shift the transmission to position D or R.
IPA immediately steers in the other direc-
tion. The [Observe surroundings] mes-
sage appears in the display.
NOTE
You will achieve the best results by wait-
ing for the steering procedure to com-
plete before pulling away.
If you back up after activation, the steer-
ing wheel is moved to the straight-ahead
position.
10. Drive forward and back up as prompted by the IPA and sonar function warning
displays, several times if necessary.
Once you have exited the parking space com-
pletely, the steering wheel is moved to the
straight-ahead position. You hear a tone and
the [Park Assist switched off] message ap-
pears in the display. You will then have to
steer and merge into traffic on your own. The
Starting and driving5-75

SYSTEM MAINTENANCE
CAUTION
Keep the surface of the sonar sensors (if
equipped) (located on the front and rear
bumper fascia) free from accumulations of
snow, ice and dirt. Do not scratch the sur-
face of the sonar sensors when cleaning. If
the sensors are covered, the accuracy of
the sonar function will be diminished.During the first 1,200 miles (2,000 km), fol-
low these recommendations to obtain maxi-
mum engine performance and ensure the fu-
ture reliability and economy of your new
vehicle. Failure to follow these recommenda-
tions may result in shortened engine life and
reduced engine performance.
•Avoid driving for long periods at constant
speed, either fast or slow, and do not run
the engine over 4,000 RPM.
•Do not accelerate at full throttle in any
gear.
•Avoid quick starts.
•Avoid hard braking as much as possible.
•Do not tow a trailer for the first 500 mi
(805 km). Your engine, axle or other parts
could be damaged.
You should also observe these notes on
break-in if the engine or parts of the drive
train on your vehicle have been replaced.
CAUTION
In certain driving and driving safety sys-
tems, the sensors adjust automatically
while a certain distance is being driven af-
ter the vehicle has been delivered or after
repairs. Full system effectiveness is not
reached until the end of this teach-in pro-
cess.
Brake pads/linings and rotors that are ei-
ther new or have been replaced only
achieve optimum braking effect after sev-
eral hundred miles of driving. Compensate
for the reduced braking effect by applying
greater force to the brake pedal
BREAK-IN SCHEDULE
Starting and driving5-85