tow INFINITI QX30 2018 Owner's Guide
Page 404 of 538
1Detected parking space on the left.
2Parking symbol.
3Detected parking space on the right.
IPA is activated automatically when driving
forwards. The system is operational at
speeds of up to approximately 19 MPH (30
km/h). While in operation, the system inde-
pendently locates and measures parking
spaces on both sides of the vehicle
IPA will only detect parking spaces:
•Adjacent to the vehicle.
•Parallel or at right angles to the direction
of travel.
•That are parallel to the direction of travel
and are at least 5 ft (1.5 m) wide.
•That are parallel to the direction of travel
and at least 3.3 ft (1.0 m) longer than your
vehicle.
•That are at right angles to the direction of
travel and at least 3.3 ft (1.0 m) wider than
your vehicle.
NOTE
IPA cannot measure the length of a parking
space if it is at right angles to the direction of
travel. You will need to judge whether your
vehicle will fit in the parking space
When driving at speeds below 19 MPH (30
km/h) you will see parking symbol
2as a
status indicator in the vehicle information
display. When a parking space has been de-
tected, an arrow towards the right
3or the
left
1also appears. IPA only displays park-
ing spaces on the front-passenger side as
standard. Parking spaces on the driver's side
are displayed as soon as the turn signal on the
driver's side is activated. When parking on the
driver's side, this must remain activated until
you confirm the use of IPA by pressing the
<OK> button on the steering wheel. The sys-
tem automatically determines whether the
parking space is parallel or at right angles to
the direction of travel.
A parking space is displayed while you are
driving past it, and until you are approxi-
mately 50 ft (15 m) away from it.
PARKING
NOTE
When the sonar function detects obstacles,
you are responsible for braking in good time.
1. Stop the vehicle when the parking symbol shows the desired parking space in the
combination meter
2. Shift into position R. The [Start Park Assist? Yes: OK No:]
message appears in the vehicle informa-
tion display.
3. To cancel the procedure: press the
button on the steering wheel or pull away
or
4. To park using IPA press the <OK>button
on the steering wheel. The Park Assist
[Observe surroundings] message appears
in the vehicle information display.
5. Release the steering wheel.
6. Back up the vehicle, being ready to brake at all times. When backing up, drive at a
speed below 5 MPH (10 km/h). Other-
wise, IPA will be canceled.
NSD696
Upper display
Starting and driving5-73
Page 405 of 538
7. Stop as soon as the sonar function soundsthe continuous warning tone, if not be-
fore. Maneuvering may be required in
tight parking spaces.
The [Park Assist active Select D Observe
surroundings] message appears in the ve-
hicle information display.
8. Select transmission position D (Drive) while the vehicle is stationary.
IPA immediately steers in the other direc-
tion.
The [Park Assist Observe surroundings]
message appears in the vehicle informa-
tion display.
NOTE
You will achieve the best results by wait-
ing for the steering procedure to com-
plete before pulling away.
9. Drive forwards and be ready to brake at all times.
Maneuvering may be required in tight
parking spaces. Drive forward and back
up as prompted by the IPA and sonar
function warning displays, several times if
necessary. 10. Stop as soon as the sonar function
sounds the continuous warning tone, if
not before.
The [Park Assist active Select R] [Ob-
serve surroundings] message appears in
the vehicle information display.
As soon as the parking procedure is
complete the [Park Assist switched off]
message appears and a warning tone
sounds. The vehicle is now parked.
11. Before leaving the vehicle, secure the ve- hicle against rolling away unintentionally:
•The electric parking brake must be ap-
plied.
•The transmission must be in position P
(Park) and the transmission position
display must show P in the vehicle
information display.
•The key must be removed from the
ignition switch.
•On uphill or downhill gradients, the
front wheels must be turned towards
the curb.
IPA no longer supports you with steering in-
terventions. When IPA is finished, you must
steer again yourself. The sonar function is still
available. Parking tips:
•The way your vehicle is positioned in the
parking space after parking is dependent
on various factors. These include the posi-
tion and shape of the vehicles parked in
front and behind it and the conditions of
the location. It may be the case that IPA
guides you too far into a parking space, or
not far enough into it. In some cases, it
may also lead you across or onto the curb.
If necessary you should cancel the parking
procedure with IPA.
•During the parking maneuver, the system
will indicate when you should shift to R
(Reverse) or D (Drive). However, you can
freely choose to shift gear whenever you
feel you need to. Should the transmission
change take place too early, the parking
procedure will be canceled. A sensible
parking position can no longer be achieved
from this position.
EXITING A PARKING SPACE
In order that IPA can support when exiting
the parking space:
•You need to have parked using IPA.
•The border of the parking space must be
high enough at the front and the rear. A
curb stone is too small, for example.
5-74Starting and driving
Page 416 of 538
SYSTEM MAINTENANCE
CAUTION
Keep the surface of the sonar sensors (if
equipped) (located on the front and rear
bumper fascia) free from accumulations of
snow, ice and dirt. Do not scratch the sur-
face of the sonar sensors when cleaning. If
the sensors are covered, the accuracy of
the sonar function will be diminished.During the first 1,200 miles (2,000 km), fol-
low these recommendations to obtain maxi-
mum engine performance and ensure the fu-
ture reliability and economy of your new
vehicle. Failure to follow these recommenda-
tions may result in shortened engine life and
reduced engine performance.
•Avoid driving for long periods at constant
speed, either fast or slow, and do not run
the engine over 4,000 RPM.
•Do not accelerate at full throttle in any
gear.
•Avoid quick starts.
•Avoid hard braking as much as possible.
•Do not tow a trailer for the first 500 mi
(805 km). Your engine, axle or other parts
could be damaged.
You should also observe these notes on
break-in if the engine or parts of the drive
train on your vehicle have been replaced.
CAUTION
In certain driving and driving safety sys-
tems, the sensors adjust automatically
while a certain distance is being driven af-
ter the vehicle has been delivered or after
repairs. Full system effectiveness is not
reached until the end of this teach-in pro-
cess.
Brake pads/linings and rotors that are ei-
ther new or have been replaced only
achieve optimum braking effect after sev-
eral hundred miles of driving. Compensate
for the reduced braking effect by applying
greater force to the brake pedal
BREAK-IN SCHEDULE
Starting and driving5-85
Page 419 of 538
CAUTION
Never tow the vehicle with one axle raised.
This may damage the differential. Damage
of this sort is not covered by the warranty.
All wheels must be fully raised (see "Four-
Wheel Drive (4WD) models" in the "6. In
case of emergency" section)
4WD, together with VDC, improves the trac-
tion of your vehicle whenever a drive wheel
spins due to insufficient grip.
If you fail to adapt your driving style, 4WD
can neither reduce the risk of an accident nor
override the laws of physics. 4WD cannot
take account of road, weather, and traffic
conditions. 4WD is only an aid. You are re-
sponsible for the distance to the vehicle in
front, for vehicle speed, for braking in good
time, and for staying in lane.
If a drive wheel spins due to insufficient grip
•When pulling away, only depress the ac-
celerator pedal as far as is necessary.
•Accelerate less when driving.
NOTE
In wintry driving conditions, the maximum
effectiveness of 4WD can only be achieved if
you use winter tires (M+S tires), with snow
chains if necessary.
WARNING
•Do not stop or park the vehicle over
flammable materials such as dry grass,
waste paper or rags. They may ignite
and cause a fire.
•Safe parking procedures require that
both the parking brake be applied and
the P (Park) position engaged. Failure to
do so could cause the vehicle to move
unexpectedly or roll away and result in
an accident.
•When parking the vehicle, make sure the
P (Park) position is engaged. The shift
lever cannot be moved out of the P
(Park) position without depressing the
brake pedal.
•Never leave the engine running while the
vehicle is unattended.
•Do not leave children unattended inside
the vehicle. They could unknowingly ac-
tivate switches or controls or move the
vehicle. Unattended children could be-
come involved in serious accidents.
•To help avoid risk of injury or death
through unintended operation of the
vehicle and/or its systems, do not leave
children, people who require the assis-
tance of others, or pets unattended in your vehicle. Additionally, the tempera-
ture inside a closed vehicle on a warm
day can quickly become high enough to
cause a significant risk of injury or death
to people and pets.
CAUTION
Always secure the vehicle correctly against
rolling away. Otherwise, the vehicle or its
drive train could be damaged.
To ensure that the vehicle is secured against
rolling away unintentionally:
•The electric parking brake must be applied.
•The transmission must be in position P
(Park) and the transmission position dis-
play must show P in the vehicle informa-
tion display.
•The key must be removed from the ignition
switch.
•On uphill or downhill gradients, the front
wheels must be turned towards the curb.
PARKING
5-88Starting and driving
Page 420 of 538
1. Firmly apply the parking brake.
2. Press the P (Park) button.
3. To help prevent the vehicle from movinginto traffic when parked on an incline, it is
a good practice to turn the wheels as
illustrated.
HEADED DOWNHILL WITH CURB
1
Turn the wheels into the curb and move
the vehicle forward until the curb side
wheel gently touches the curb. Then apply
the parking brake.
HEADED UPHILL WITH CURB
2
Turn the wheels away from the curb and
allow the vehicle to move back until the
curb side wheel gently touches the curb.
Then apply the parking brake. HEADED UPHILL OR DOWNHILL,
WITHOUT CURB
3
Turn the wheels toward the side of the
road so the vehicle will move away from
the center of the road if the vehicle moves.
Then apply the parking brake.
4.
Put the ignition switch in the OFF position.
SWITCHING OFF THE ENGINE
WARNING
The automatic transmission switches to
position N (Neutral) when you switch off
the engine. The vehicle may roll away.
There is a risk of an accident.
After switching off the engine, always
switch to position P (Park). Prevent the
parked vehicle from rolling away by apply-
ing the parking brake.
Procedure
1. Apply the electric parking brake.
2. Shift the transmission to position P (Park).
3. With the key: turn the key to the position
OFF in the ignition switch and remove it
The immobilizer is activated.
If you switch the engine off with the trans-
mission in position R (Reverse) or D (Drive),
the automatic transmission shifts to N (Neu-
tral) automatically.
With the key: if you then open the driver's
door or the front-passenger door or remove
the key from the ignition, the automatic
transmission shifts to P (Park) automatically.
If you want the automatic transmission to
remain in neutral N (Neutral), e.g. when hav-
ing the vehicle cleaned in an automatic car
wash with a towing system:
With the key:
1. Switch the ignition on.
2. Depress the brake pedal and keep it de- pressed.
3. Shift to N (Neutral).
SSD0488Z
Starting and driving5-89
Page 430 of 538
6 In case of emergency
Hazard warning flasher switch.............6-2
Flat tire ........................... .6-2
Tire Pressure Monitoring System (TPMS) .....6-2
Stopping vehicle .................... .6-3
Warning triangle (if equipped) ............6-4
Run-flat tires ...................... .6-4Removing and fitting wheels
.............6-5
Jump starting ...................... .6-10
Push starting ....................... .6-12
If your vehicle overheats ................ .6-13
Towing your vehicle .................. .6-14
Towing recommended by INFINITI ........6-14
Page 441 of 538
CAUTION
•Always connect positive+to positive
+and negative-to body ground (for
example, strut mounting bolt, engine lift
bracket, etc.) – not to the battery's
negative
-.
•Be sure that the jumper cables do not
touch moving parts in the engine com-
partment and that the cable clamps do
not contact any other metal.
9. Start the engine of the other vehicle
Aand let it run for a few minutes. Keep the
engine speed at about 2,000 rpm.
10. Start the engine of your vehicle
Bin the
normal way.
CAUTION
Do not keep the starter motor engaged for
more than 10 seconds. If the engine does
not start right away, place the ignition
switch in the OFF position and wait 10 sec-
onds before trying again.
11. After starting the engine of your vehicle, carefully disconnect the negative lead
and then the positive lead (
4→3→2→1). 12. Remove and dispose of the cloth that
was used to cover the ventilator holes as
it may be contaminated with corrosive
acid.
13. Install the ventilator caps (if equipped).
14. Close the hood.
NOTE
For models which incorporate the Idle Stop/
Start System:
•Ensure that the battery fitted is the special
battery that is enhanced with regard to the
charge-discharge capacity and life perfor-
mance. Avoid using any other battery for
the Idle Stop/Start System, as this may
cause early deterioration of the battery or
a malfunction of the Idle Stop/Start Sys-
tem. It is recommended that a Genuine
INFINITI battery is fitted. For more infor-
mation, it is recommended you contact an
INFINITI retailer.
•If the battery terminal is disconnected (for
battery replacement, etc.) and then recon-
nected, there may be some delay before
the Idle top/Start System reactivates. Do not attempt to start the engine by pushing
the vehicle.
CAUTION
•Automatic Transmission (AT) model
cannot be push-started or tow-started.
Attempting to do so may cause damage
to the transmission.
•Three-way catalyst equipped models
should not be started by pushing. At-
tempting to do so may cause damage to
the three-way catalyst.
•Never try to start the vehicle by towing
it; when the engine starts, the forward
surge could cause the vehicle to collide
with the tow vehicle.
PUSH STARTING
6-12In case of emergency
Page 443 of 538
When towing your vehicle, all jurisdictions
and local regulations for towing must be fol-
lowed. Incorrect towing equipment could
damage your vehicle. Towing instructions are
available from an INFINITI retailer. Local ser-
vice operators are generally familiar with the
applicable laws and procedures for towing.
To assure proper towing and to prevent ac-
cidental damage to your vehicle, INFINITI
recommends having a service operator tow
your vehicle. It is advisable to have the service
operator carefully read the following precau-
tions.
WARNING
•Never ride in a vehicle that is being
towed.
•Never get under your vehicle after it has
been lifted by a tow truck.
CAUTION
•When towing, make sure that the trans-
mission, axles, steering system and
powertrain are in working condition. If
any of these conditions apply, dollies or
a flatbed tow truck must be used.
•Always attach safety chains before
towing.
TOWING RECOMMENDED BY
INFINITI
INFINITI recommends towing your vehicle
based upon the type of drivetrain. Please re-
fer to the diagrams in this section to ensure
that your vehicle is properly towed.
NCE451
FWD (2WD) models
TOWING YOUR VEHICLE
6-14In case of emergency
Page 444 of 538
Two-Wheel Drive (FWD) models
CAUTION
NEVER tow automatic transmission (DCT)
models with the front wheels on the
ground or with all four wheels on the
ground (forwards or backwards), as this
may cause serious and expensive damage
to the transmission. If it is necessary to tow
the vehicle with the rear wheels raised, al-
ways use towing dollies under the front
wheels.
Four-Wheel Drive (4WD) models
INFINITI recommends that towing dollies be
used under the front or rear wheels when
towing your vehicle or the vehicle be placed
on a flatbed tow truck as illustrated.
CAUTION
Never tow 4WD models with any of the
wheels on the ground. Doing so will cause
serious and expensive damage to the
drivetrain.
Vehicle recovery (freeing a stuck
vehicle)
WARNING
To avoid vehicle damage, serious personal
injury or death when recovering a stuck ve-
hicle:
•Contact a professional towing service to
recover the vehicle if you have any ques-
tions regarding the recovery procedure.
•Tow chains or cables must be attached
only to main structural members of the
vehicle.
•Do not use the vehicle tie downs to tow
or free a stuck vehicle.
•Only use devices specifically designed
for vehicle recovery and follow the
manufacturer's instructions.
•Always pull the recovery device straight
out from the front of the vehicle. Never
pull at an angle.
•Route recovery devices so they do not
touch any part of the vehicle except the
attachment point.
•On vehicles with a push button ignition
switch: you must remove the start/stop
NCE450
4WD models
In case of emergency6-15
Page 445 of 538
button and use the key (see " Push-
button ignition switch (if equipped)" in
the "5. Starting and driving" section).
Otherwise the automatic transmission
may shift to position P (Park) when the
driver's or front passenger door are
opened, which could lead to damage to
the transmission.
If your vehicle is stuck in sand, snow, mud,
etc., use a tow strap or other device designed
specifically for vehicle recovery. Always fol-
low the manufacturer’s instructions for the
recovery device.
Rocking a stuck vehicle
WARNING
•To avoid potential injury, stand clear of
a stuck vehicle.
•Do not spin your tires at high speed. This
could cause them to explode and result
in serious injury. Parts of your vehicle
could also overheat and be damaged. If your vehicle is stuck in sand, snow, mud,
etc., use the following procedure:
1. Turn off the Vehicle Dynamic Control
(VDC) system.
2. Make sure the area in front and behind the vehicle is clear of obstructions.
3. Turn the steering wheel right and left to clear an area around the front tires.
4. Slowly rock the vehicle forward and back- ward.
•Shift back and forth between R (Reverse)
and D (Drive).
•Apply the accelerator as little as possible
to maintain the rocking motion.
•Release the accelerator pedal before shift-
ing between R (Reverse) and D (Drive).
•Do not spin the tires above 35 MPH (55
km/h).
5. If the vehicle cannot be freed after a few tries, contact a professional towing ser-
vice to remove the vehicle.
6-16In case of emergency