ESP INFINITI QX30 2019 Owner's Manual

Page 35 of 436

WARNING
Do not allow children to play with the seat
belts. Most seating positions are equipped
with Automatic Locking Retractor (ALR)
mode seat belts. If the seat belt becomes
wrapped around a child’s neck with the
ALR mode activated, the child can be seri-
ously injured or killed if the seat belt re-
tracts and becomes tight. This can occur
even if the vehicle is parked. Unbuckle the
seat belt to release the child. If the seat belt
can not be unbuckled or is already unbuck-
led, release the child by cutting the seat
belt with a suitable tool (such as a knife or
scissors) to release the seat belt.
Children need adults to help protect them.
They need to be properly restrained.
In addition to the general information in this
manual, child safety information is available
from many other sources, including doctors,
teachers, government traffic safety offices,
and community organizations. Every child is
different, so be sure to learn the best way to
transport your child.There are three basic types of child restraint
systems:•Rear-facing child restraint
•Forward-facing child restraint
•Booster seat
The proper restraint depends on the child’s
size. Generally, infants up to about 1 year and
less than 20 lb (9 kg) should be placed in
rear-facing child restraints. Forward-facing
child restraints are available for children who
outgrow rear-facing child restraints and are
at least 1 year old. Booster seats are used to
help position a vehicle lap/ shoulder belt on a
child who can no longer use a forward-facing
child restraint.
WARNING
Infants and children need special protec-
tion. The vehicle’s seat belts may not fit
them properly. The shoulder belt may come
too close to the face or neck. The lap belt
may not fit over their small hip bones. In an
accident, an improperly fitting seat belt
could cause serious or fatal injury. Always
use appropriate child restraints.
All U.S. states and Canadian provinces or
territories require the use of approved childrestraints for infants and small children. See
"Child restraints" for more information.
A child restraint may be secured in the vehicle
by using either the LATCH (Lower Anchor
and Tethers for CHildren) system or with the
vehicle seat belt. For additional information,
refer to "Child restraints".
INFINITI recommends that all pre-teens and
children be restrained in the rear seat. Stud-
ies show that children are safer when prop-
erly restrained in the rear seat than in the
front seat.
This is especially important because your
vehicle has a supplemental restraint system
(air bag system) for the front passenger. (See
"Supplemental Restraint System (SRS)"
later in this section.)
INFANTS
Infants up to at least 1 year old should be
placed in a rear-facing child restraint.
INFINITI recommends that infants be placed
in child restraints that comply with Federal
Motor Vehicle Safety Standards or Canadian
Motor Vehicle Safety Standards. You should
choose a child restraint which fits your ve-
hicle and always follow the manufacturer’s
instructions for installation and use.
CHILD SAFETY
Safety — seats, seat belts and supplemental restraint system1-17

Page 60 of 436

WARNING
•The seat belts, the side air bags and cur-
tain air bags are most effective when
you are sitting well back and upright in
the seat with both feet on the floor. The
side air bag and curtain air bag inflate
with great force. Do not allow anyone to
place their hand, leg or face near the side
air bag on the side of the seatback of the
front seat or near the side roof rails. Do
not allow anyone sitting in the front
seats or rear outboard seats to extend
their hand out of the window or lean
against the door. Some examples of
dangerous riding positions are shown in
the previous illustrations.
•When sitting in the rear seats, do not
hold onto the seatback of the front
seats. If side air bags and curtain air
bags inflate, you may be seriously in-
jured. Be especially careful with chil-
dren, who should always be properly re-
strained. Some examples of dangerous
riding positions are shown in the illus-
trations.
•Do not use seat covers on the front seat-
backs. They may interfere with the side
air bag inflation.SSS0162Z
WRS0363Z
SSS0159Z
1-42Safety — seats, seat belts and supplemental restraint system

Page 65 of 436

•The front passenger seat is occupied by a
properly restrained child up to the approxi-
mate size and weight of a one year old, the
<PASSENGER AIRBAG OFF> indicator
light lights up after the system self-test
and remains lit. This indicates that the
front passenger front air bag is disabled.
If neither the <PASSENGER AIRBAG
OFF> or the <PASSENGER AIRBAG ON>
indicator lights light up, or if either indica-
tor light only lights up intermittently during
the journey, the front passenger seat
may not be used for a child restraint. Use
another seating position for the child re-
straint. For further information see
&#34;Troubleshooting&#34; later in this section.
•The front passenger seat is occupied by a
properly restrained child who is larger than
the approximate size and weight of a one
year old, either the <PASSENGER AIR-
BAG ON> or <PASSENGER AIRBAG OFF>
indicator light lights up and remains lit af-
ter the system self-test depending on the
result of the classification. The result of
the classification is dependent on, among
other factors, the child restraint system
and the child&#39;s build.
Move the front passenger seat as far back
as possible. See &#34;Child restraints&#34; earlier in
this section.
•The front passenger seat is occupied by a
person with a smaller build (e.g. a teenager
or small adult), either the <PASSENGER
AIRBAG ON> or <PASSENGER AIRBAG
OFF> indicator light lights up and remains
lit after the system self-test depending on
the result of the classification.
– If the <PASSENGER AIRBAG ON> indi-
cator light lights up, move the front
passenger seat as far back as possible.
Alternatively, a person with a small
build can sit on a rear seat.
– If the <PASSENGER AIRBAG OFF>
indicator light is lit, a person with a
smaller build should not use the front
passenger seat.
•The front passenger seat is occupied by an
adult or a person with a build correspond-
ing to that of an adult, the <PASSENGER
AIRBAG ON> indicator light lights up after
the system self-test and remains lit. This
indicates that the front passenger front air
bag is enabled.If the automatic front passenger front air bag
deactivation system is malfunctioning, the
red
restraint system warning light in the
combination meter and the <PASSENGER
AIRBAG OFF> indicator light light up simul-
taneously. The front passenger front air bag
is disabled in this case and does not deploy
during an accident. Have the system checked
as soon as possible by qualified technicians. It
is recommended that you visit an INFINITI
retailer for this service.
Safety — seats, seat belts and supplemental restraint system1-47

Page 66 of 436

Troubleshooting
Problem Possible causes/consequences and solutions
The <PASSENGER AIRBAG OFF> indicator lamp
lights up and remains lit, even though the front
passenger seat is occupied by an adult or a person
with a build corresponding to that of an adult
•Make sure the conditions for a correct classification of the person on the front passenger seat are met
(see &#34;Front passenger air bag&#34; earlier in this section).
•If the <PASSENGER AIRBAG OFF> indicator light remains lit, the front passenger seat may not be used.•Have the automatic front passenger front air bag deactivation system checked as soon as possible. It is
recommended that you visit an INFINITI retailer for this service.
The <PASSENGER AIRBAG OFF> indicator lamp
does not light up and/or does not stay on.
•Make sure there is nothing between the seat and the child restraint system.•Make sure that the entire base of the child restraint system rests on the seat cushion of the front
passenger seat.
•When installing the child restraint system, make sure that the seat belt is tight. Do not pull the seat belt
tight with the front passenger seat adjustment. This could result in the seat belt and the child restraint
system being pulled too tightly.
•Check that the child restraint system is installed correctly.•Make sure that no objects are applying additional weight to the seat.•Have the automatic front passenger front air bag deactivation system checked as soon as possible. It is
recommended that you visit an INFINITI retailer for this service.
1-48Safety — seats, seat belts and supplemental restraint system

Page 97 of 436

•Lane Departure Warning (LDW)
•Blind Spot Warning (BSW)
•Rear window wiper
Deactivating/activating VDC:
The vehicle should be driven with the Vehicle
Dynamic Control (VDC) system on for most
driving conditions.
If the vehicle is stuck in mud or snow, the
VDC system reduces the engine output to
reduce wheel spin. The engine speed will be
reduced even if the accelerator is depressed
to the floor. If maximum engine power is
needed to free a stuck vehicle, turn the VDC
system off.
For further information about VDC, see &#34;Ve-
hicle Dynamic Control (VDC) system&#34;.
1. Start the engine.
2. Press the
orbutton on the
steering wheel to select the [DriveAssist]
menu.
3. Press the
orbutton to select
[ESP].
4. Press the <OK> button.
The current selection is displayed.5. To activate/deactivate: press the <OK>
button again.
VDC is deactivated if the
warning
light in the combination meter lights up
continuously when the engine is running.
If both the
warning light andwarning light are lit continuously, VDC is not
available due to a malfunction.
Activating/deactivating Forward Emergency
Braking:
1. Press theorbutton on the
steering wheel to select the [DriveAssist]
menu.
2. Press the
orbutton to select
[Emergency Brake].
3. Press the <OK> button.
The current selection is displayed.
4. To activate/deactivate: press the <OK>
button again.
When Forward Emergency Braking is de-
activated, the
symbol appears in the
vehicle information display in the assis-
tance graphic display.
For further information about Forward
Emergency Braking, see &#34; Forward emer-
gency braking (FEB) system (if equipped)&#34;.Activating/deactivating Blind Spot
Warning (BSW):
1. Press the
orbutton on the
steering wheel to select the [DriveAssist]
menu.
2. Press the
orbutton to select
[Blind Spot Warning].
3. Press the <OK> button.
The current selection is displayed.
4. To activate/deactivate: press the <OK>
button again.
For further information about Blind Spot
Warning, see &#34; Blind Spot Warning (BSW)
system (if equipped)&#34;.
Activating/deactivating Lane Departure
Warning (LDW):
1. Press the
orbutton on the
steering wheel to select the [DriveAssist]
menu on the Menu bar.
2. Press the
orbutton to select
[Lane Departure Warning].
3. Press the<OK>button on the steering
wheel. The current selection is displayed.
4. Press the<OK>to confirm.
Instruments and controls2-23

Page 113 of 436

Message Possible causes/consequences and solutions
[Front Passenger Airbag
Disabled See Operator&#39;s
Manual]The front-passenger front air bag is disabled during the journey although an adult or person of corresponding stature is on the
front passenger seat.
Front passenger seat adult occupants who are properly seated and using the seat belt as outlined in this manual should not cause
the front passenger air bag to be automatically turned OFF. For small adults it may be turned OFF, however if the occupant takes
his/her weight off the seat cushion (for example, by not sitting upright, by sitting on an edge of the seat, or by otherwise being out
of position), this could cause the sensor to turn the air bag OFF. Always be sure to be seated and wearing the seat belt properly for
the most effective protection by the seat belt and supplemental air bag.
If additional forces are applied to the seat, the system may interpret the occupant&#39;s weight as lower than it actually is.
1. Stop the vehicle in a safe area away from traffic as soon as possible, paying attention to road and traffic conditions.
2. Secure the vehicle against rolling away.
3. Switch the ignition off.
4. Have the occupant on the front-passenger seat step out of the vehicle.
5. Make sure that the seat is unoccupied, close the front passenger door and switch on the ignition.
6. Observe the <PASSENGER AIR BAG> indicator lights in the center console and the vehicle information display and check the
following. Seat unoccupied and ignition switched on:
- The <PASSENGER AIR BAG OFF> and <PASSENGER AIR BAG ON> indicator lights must light up simultaneously for
approximately six seconds.
- The <PASSENGER AIR BAG OFF> indicator lights must then light up and remain lit. If the indicator light is on, the automatic
front-passenger front air bag deactivation system has disabled the front-passenger front air bag (see &#34;Front passenger air bag
and status light&#34;)
- the [Front Passenger Airbag Enabled See Operator&#39;s Manual] or [Front Passenger Airbag Disabled See Operator&#39;s Manual]
display messages must not be shown in the vehicle information display.
7. Wait for a period of at least 60 seconds until the necessary system checks have been completed.
8. Make sure that the display messages do not appear in the vehicle information display.
If these conditions are met, the front-passenger seat can be occupied again. Whether the <PASSENGER AIR BAG OFF> or <ON>
indicator light remains lit or goes out depends on how the automatic front passenger front air bag deactivation system classifies the
occupant.
If, after taking the steps above, you still believe the system is not operating properly, have it checked immediately. It is recommended
you visit an INFINITI retailer for this service.
For further information on the automatic front-passenger front air bag deactivation feature (see &#34;Front passenger air bag and
status light&#34;).
Instruments and controls2-39

Page 115 of 436

Lights
NOTE
Vehicles with LEDs in the light clusters: The display message for the corresponding light will only appear if all the LEDs have failed.
Message Possible causes/consequences and solutions
[Check Left Cornering
Light] or [Check Right
Cornering Light]The left or right-hand cornering light is faulty.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Check Left Low Beam] or
[Check Right Low Beam]The left or right-hand low beam headlight is faulty.•Check whether you are permitted to replace the bulb yourself (see &#34;Lights&#34;).
or:
•Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Check Rear Left Turn
Signal] or [Check Rear
Right Turn Signal]The rear left or right-hand turn signal is faulty.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Check Front Left Turn
Signal] or [Check Front
Right Turn Signal]The front left or right-hand turn signal is faulty.•Check whether you are permitted to replace the bulb yourself (see &#34;Lights&#34;).
or:
•Have the system checked. It is recommended you visit an INFINITI retailer for this service.
Instruments and controls2-41

Page 126 of 436

Tires
Message Possible causes/consequences and solutions
[Please Correct Tire
Pressure]The tire pressure is too low in at least one of the tires, or the tire pressure difference between the wheels is too great.
1. Check the tire pressures at the next opportunity (see &#34;Wheels and tires&#34;)
2. If necessary, correct the tire pressure.
3. Restart the tire pressure monitoring system (see &#34;Restarting TPMS&#34;)
[Check Tire(s)] The tire pressure in one or more tires has dropped significantly The wheel position is displayed in the vehicle information display
A warning tone also sounds.
WARNING
Underinflated tires pose the following risks:•The tires may burst, especially as the load and vehicle speed increase.•The tires may wear excessively and/or unevenly, which may greatly impair tire traction.•The driving characteristics, as well as steering and braking, may be greatly impaired.
There is a risk of an accident.
1. Stop the vehicle without making any sudden steering or braking maneuvers. Pay attention to the traffic conditions as you do so.
2. Secure the vehicle against rolling away.
3. Check the tires and, if necessary, follow the instructions for a flat tire (see &#34;Flat tire&#34;).
4. Check the tire pressures and, if necessary, correct the tire pressure.
[Warning Tire Malfunction] The tire pressure in one or more tires has dropped suddenly. The wheel position is displayed in the vehicle information display.
WARNING
If you drive with a flat tire, there is a risk of the following hazards:•A flat tire affects the ability to steer or brake the vehicle.•You could lose control of the vehicle.•Continued driving with a flat tire will cause excessive heat buildup and possibly a fire.
There is a risk of an accident.
1. Stop the vehicle without making any sudden steering or braking maneuvers. Pay attention to the traffic conditions as you do so.
2. Secure the vehicle against rolling away.
3. Check the tires and, if necessary, follow the instructions for a flat tire (see &#34;Flat tire&#34;).
2-52Instruments and controls

Page 134 of 436

IMMOBILISER
The immobiliser prevents your vehicle from
being started without the correct key.
•To activate with the key: remove the key
from the ignition lock.
•To deactivate:switch on the ignition.
When leaving the vehicle, always take the key
with you and lock the vehicle. Anyone can
start the engine if a valid key has been left
inside the vehicle.
NOTE
The immobiliser is always deactivated when
you start the engine.
FCC Notice:
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not
cause harmful interference, and (2) this de-
vice must accept any interference received,
including interference that may cause unde-
sired operation.NOTE
Changes or modifications not expressly ap-
proved by the party responsible for compli-
ance could void the user’s authority to oper-
ate the equipment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation
is subject to the following two conditions: (1)
this device may not cause interference, and
(2) this device must accept any interference,
including interference that may cause unde-
sired operation of the device.
ANTI-THEFT ALARM SYSTEM
(IF EQUIPPED)
To arm:lock the vehicle with the key or Intel-
ligent Key. Indicator light
1flashes. The
alarm system is armed after approximately
15 seconds.
To deactivate:unlock the vehicle with the key
or Intelligent Key.
or
Insert the key into the ignition switch.
A visual and audible alarm is triggered if the
alarm system is armed and you open:
•A door.
•The vehicle with the emergency key element.
•The lift gate.
•The hood.
NIC2750
SECURITY SYSTEM
2-60Instruments and controls

Page 137 of 436

•Vehicles with a rain sensor: if the wind-
shield becomes dirty in dry weather con-
ditions, the windshield wipers may be
activated inadvertently. This could
damage the windshield wiper blades or
scratch the windshield.
For this reason, you should always
switch off the windshield wipers in dry
weather.
Vehicles with a rain sensor: in the
orposition, the appropriate wiping fre-
quency is automatically set according to the
intensity of the rain. In the
position, the
rain sensor is more sensitive than in the
position, causing the windshield wiper
to wipe more frequently.
If the wiper blades are worn, the windshield
will no longer be wiped properly. This could
prevent you from observing the traffic condi-
tions.
SWITCHING THE REAR WINDOW
WIPER ON/OFF
WARNING
In freezing temperatures the washer solu-
tion may freeze on the windshield and ob-
scure your vision which may lead to an ac-
cident. Warm the windshield with the
defroster before you wash the windshield.
CAUTION
•Do not operate the washer continuously
for more than 30 seconds.
•Do not operate the washer if the win-
dow washer fluid reservoir is empty.
•Do not fill the window washer reservoir
tank with washer fluid concentrates atfull strength. Some methyl alcohol
based washer fluid concentrates may
permanently stain the grille if spilled
while filling the window washer reser-
voir tank.
•Pre-mix washer fluid concentrates with
water to the manufacturer’s recom-
mended levels before pouring the fluid
into the window washer reservoir tank.
Do not use the window washer reservoir
tank to mix the washer fluid concentrate
and water.
1Switch
2Wipes with washer fluid
3Switches on intermittent wiping
4Switches off intermittent wiping
5Wipes with washer fluid
1. Switch the ignition switch to the ON po-
sition.
2. Turn switch
1on the combination switch
to the corresponding position.
When the rear window wiper is switched
on, the
symbol appears in the as-
sistance graphic in the combination meter.
Further information on the assistance
graphic (see &#34;Showing the distance
display&#34; earlier in this section).
NIC2617
Instruments and controls2-63

Page:   1-10 11-20 21-30 31-40 41-50 ... 60 next >