Revers INFINITI QX56 2004 Factory Service Manual

RUNNING BOARDS
EI-25
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: August 20072004 QX56
RUNNING BOARDSPFP:96110
Removal and InstallationEIS002XD
1. Remove bolts and remove running board from running board brackets.
2. Remove nuts and remove step pad from running board.
3. Remove nuts and bolts and remove running board brackets.
4. Remove screws and remove front and rear mud guards.
Installation is in the reverse order of removal.
1. Running board bracket 2. Front mud guard LH 3. Running board
4. Step pad 5. Rear mud guard LH
WIIA0265E

EI-26
REAR SPOILER
Revision: August 20072004 QX56
REAR SPOILERPFP:96030
Removal and InstallationEIS002XE
1. Remove back door trim. Refer to EI-41, "BACK DOOR TRIM" .
2. Disconnect harness to high-mount stop lamp.
3. Disconnect washer tube.
4. Remove nuts, release clips and remove rear air spoiler.
5. Remove nuts and remove high-mount stop lamp.
Installation is in the reverse order of removal.
1. Grommet 2. Plastic clip 3. Nut
4. Rear air spoiler 5. High-mount stop lamp
LIIA1328E

ROOF RACK
EI-27
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: August 20072004 QX56
ROOF RACKPFP:73155
Removal and InstallationEIS002XF
1. Remove screws, raise tie down hooks and remove finisher covers.
2. Remove bolts and remove front crossbar and gasket.
3. Remove screws, raise tie down hooks and remove slide rail covers.
4. Remove sliding crossbar.
5. Remove bolts and remove slide rails.
Installation is in the reverse order of removal.

To install finisher covers and slide rail covers, rotate tie hooks to the 50 degrees up position and slip cover
over tie down. Press down until clip is engaged. Rotate tie down hook to the down position. Install screws.
1. Sliding crossbar 2. Finisher cover 3. Front crossbar
4. Gasket 5. Slide rail 6. Slide rail cover
LIIA1031E

EI-28
DOOR OUTSIDE MOLDING
Revision: August 20072004 QX56
DOOR OUTSIDE MOLDINGPFP:82820
Removal and InstallationEIS002XG
FRONT DOOR OUTSIDE MOLDING
Removal and Installation
1. Open windows fully.
2. Remove door mirror. Refer to GW-100, "
Door Mirror Assembly" .
3. Remove molding.

Remove hole cover and remove screw.

Lift molding from rear side.

Disconnect clips from flange.
Installation is in the reverse order of removal.
LIIA1035E

EI-32
DOOR FINISHER
Revision: August 20072004 QX56

Disconnect harness connector.
7. Remove step lamp.

Disconnect harness connector.
8. Remove door finisher and disconnect lock cable and handle cable from door handle assembly. Refer to
BL-132, "
FRONT DOOR LOCK" .
9. Remove door lock knob.
Installation is in the reverse order of removal.
REAR DOOR
1. Remove power window switch assembly.

Disconnect harness connector.
2. Remove pull handle cover.

Remove screws behind pull handle cover.
3. Remove cap from pull handle escutcheon and remove screw.
4. Remove pull handle escutcheon.
1. Power window switch assembly 2. Armrest 3. Rear door finisher LH
4. Pull handle cover 5. Cap 6. Pull handle escutcheon
7. Door lock knob 8. Step lamp 9. Rear door tweeter
LIIA1038E

DOOR FINISHER
EI-33
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: August 20072004 QX56

Remove screws behind pull handle escutcheon.
5. Remove armrest.

Remove screws behind armrest.
6. Remove step lamp.

Disconnect harness connector.
7. Remove door finisher and disconnect lock cable and handle cable from door handle assembly. Refer to
BL-135, "
REAR DOOR LOCK" .
8. Remove door lock knob.
9. Remove rear door tweeter. Refer to AV-46, "
Removal and Installation of Rear Door Tweeter" .
Installation is in the reverse order of removal.

BODY SIDE TRIM
EI-35
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: August 20072004 QX56
Installation is in the reverse order of removal.
CENTER PILLAR LOWER FINISHER
Removal and Installation
1. Remove front and rear door welts.
2. Remove seat belt anchor. Refer to SB-3, "
Removal and Installation of Front Seat Belt" .

On RH side, disconnect seat belt tension sensor.
3. Remove front and rear kicking plates. Refer to EI-35, "
KICKING PLATES" .
4. Remove center pillar lower finisher.
Installation is in the reverse order of removal.
CENTER PILLAR UPPER FINISHER
Removal and Installation
1. Remove center pillar lower finisher. Refer to EI-35, "CENTER PILLAR LOWER FINISHER" .
2. Remove assist grip.
3. Remove center pillar upper finisher.
Installation is in the reverse order of removal.
FRONT PILLAR FINISHER
Removal and Installation
1. Remove assist grip.
2. Remove front pillar finisher.
Installation is in the reverse order of removal.
KICKING PLATES
Removal and Installation
Release clips and remove front and/or rear kicking plates.
Installation is in the reverse order of removal.
MUDGUARD FINISHERS
Removal and Installation
Release clips and remove front and/or rear mudguard finishers.
Installation is in the reverse order of removal.
DOOR PARTING SEALS
Removal and Installation
1. Open front and/or rear doors fully.
2. Release clips and remove parting seals.
Installation is in the reverse order of removal.

EI-36
FLOOR TRIM
Revision: August 20072004 QX56
FLOOR TRIMPFP:74902
Removal and InstallationEIS002XK
1. Remove front seats. Refer to SE-96, "FRONT SEAT" .

Remove subwoofer. Refer to AV- 4 6 , "Removal and Installation of Subwoofer" .

Remove navigation display control unit. Refer to AV- 1 5 8 , "Removal and Installation of Display Control
Unit" .
2. Remove second row seats. Refer to SE-103, "
Second Row Outboard" and SE-103, "Second Row Cen-
ter" , if equipped.
3. Remove third row rear seat. Refer to SE-103, "
Third Row" .
4. Remove lower seat belt anchors. Refer to SB-3, "
SEAT BELTS" .
5. Remove lower body side trim. Refer to EI-34, "
BODY SIDE TRIM" .
6. Remove luggage lower side finishers (left / right). Refer to EI-39, "
LUGGAGE FLOOR TRIM" .
7. Remove kicking plates. Refer to EI-34, "
BODY SIDE TRIM" .
8. Remove center console. Refer to IP-10, "
INSTRUMENT PANEL ASSEMBLY" .
9. Remove rear console, if equipped. Refer to IP-17, "
Rear Console" .
10. Remove rear lower finisher. Refer to EI-39, "
LUGGAGE FLOOR TRIM" .
11. Remove carpet.
12. Remove floor mat hooks from front carpet.
Installation is in the reverse order of removal.
1. Inspection hole cover 2. Seal 3. Carpet
4. Floor mat hook 5. Plastic clip
WIIA0267E

EI-38
HEADLINING
Revision: August 20072004 QX56
CAUTION:
Disconnect both terminals from battery in advance.
1. Remove body side trim. Refer to EI-34, "
BODY SIDE TRIM" .
2. Remove luggage floor trim. Refer to EI-39, "
LUGGAGE FLOOR TRIM" .
3. Remove sunvisor assemblies.
4. Remove sunvisor clips.
5. Remove sunroof welt (if equipped).
6. Remove front roof console.

Disconnect harnesses.
7. Remove rear roof console.

Disconnect harnesses.
8. Remove assist grips.
9. Remove lamp assembly from rear roof finisher.

Disconnect harness.
10. Remove rear roof finisher.
11. Remove headlining.

Remove clips from rear of headlining.

Disconnect harnesses.
12. Remove rear air control.

Disconnect harness.
13. Remove rear audio control assembly.

Disconnect harness.
14. Remove lamp assemblies.

Disconnect harnesses.
15. Remove air vents.
16. Remove the front roof console bracket.
17. Remove rear roof console front bracket.
18. Remove assist grip brackets from roof.
Installation is in the reverse order of removal.
1. Headlining (without sunroof) 2. Assist grip bracket 3. Assist grip
4. Sunvisor assembly LH 5. Cap LH 6. Sunvisor holder
7. Front roof console 8. Sunglass bin 9. Sunroof welt
10. Cap RH 11. Sunvisor assembly RH 12. Rear roof console bracket
13. Rear storage bin or DVD display 14. Rear air control 15. Rear audio control assembly
16. Rear roof console 17. Rear roof console finisher 18. Rear storage bin
19. Air vent 20. Lamp assembly 21. Plastic clip
22. Headlining (with sunroof) 23. Rear lamp lens 24. Rear lamp
25. Rear roof finisher 26. Plastic clip 27. Metal clip

EI-40
LUGGAGE FLOOR TRIM
Revision: August 20072004 QX56
REMOVAL
1. Remove 2nd and 3rd row seat belts. Refer to SB-3, "SEAT BELTS" .
2. Remove third row seat belt buckles.
3. Remove third row seat assembly. Refer to SE-103, "
Third Row" .
4. Remove back door weatherstrip. Refer to EI-41, "
BACK DOOR TRIM" .
5. Remove rear luggage room lamp. Refer to EI-37, "
HEADLINING" .

Disconnect harness from lamp.
6. Remove rear upper finisher. Refer to EI-37, "
HEADLINING" .
7. Remove rear door kicking plates. Refer to EI-34, "
BODY SIDE TRIM" .
8. Remove rear lower finisher.
9. Disconnect door open/close link. Refer to BL-136, "
BACK DOOR LOCK" .
10. Remove cargo net hooks.
11. Remove luggage side lower finishers LH/RH.

Disconnect power point, RH side.
12. Remove coat hooks.
13. Remove luggage side upper finishers LH/RH.

Disconnect harness to door open/close switch, LH side.
14. Remove tie down hooks LH/RH.
15. Remove floor side finishers LH/RH.
16. Remove luggage floor board.
17. Remove storage box.
18. Remove front luggage floor bracket.
19. Remove rear luggage box bracket.
INSTALLATION
Installation is in the reverse order of removal.
1. Rear lower finisher cap 2. Rear lower finisher 3. Cap upper seat belt finisher RH
4. Luggage side finisher RH 5. Metal clip 6. Plastic clip
7. Luggage side finisher lower RH 8. Luggage floor board 9. Latch luggage floor board
10. Leak check cap 11. Cup holder 12. Tie down hook
13. Floor side finisher RH 14. Power point assembly 15. Cargo net hook
16. Rear luggage box bracket 17. Front luggage floor bracket 18. Storage box
19. Floor side finisher LH 20. Luggage side finisher upper LH 21. Luggage side finisher lower LH
22. Lid luggage side lower 23. Coat hook 24. Cap lower seat belt finisher
25. Back door open/close switch 26. Cap luggage side upper 27. Cap upper seat belt finisher LH