Ins INFINITI QX56 2004 Factory Owner's Manual

TROUBLE DIAGNOSIS FOR SYMPTOMS
ACS-53
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: August 20072004 QX56
Symptom 1: ON/OFF Switch Does Not Switch ON*1 , ON/OFF Switch Does Not
Switch OFF
*2EKS007XS
NOTE:

*1: The ICC system display in the combination meter does not illuminate.

*2: The ICC system display in the combination meter remains powered.
1. CHECK ON/OFF SWITCH
With CONSULT-II

With data monitor, check that ON/OFF switch operates normally.
OK or NG
OK >> GO TO 2.
NG >> GO TO 3.
2. CHECK ICC UNIT CONNECTOR
1. Turn ignition switch OFF.
2. Disconnect ICC unit harness connectors.
3. Check connector housing for disconnected, loose, bent, and collapsed terminals.
OK or NG
OK >> GO TO 3.
NG >>

Poor connector connection.

Repair ICC unit connector. After repair, erase DTC and perform ICC system running test. Then
perform self-diagnosis of ICC system again.
3. DIAGNOSIS CHECK
With CONSULT-II

Perform self-diagnosis with CONSULT-II. Is “CAN COMM CIRCUIT” indicated?
YES or NO
YES >> Refer to ACS-38, "DTC 20 CAN COMM CIRCUIT" .
NO >> Refer to ACS-41, "
DTC 46 OPERATION SW CIRC" .
Symptom 2: The ICC System Cannot Be Set (ON/OFF Switch Turns On/Off)EKS007XT
The ICC cannot be set in the following cases.

When the vehicle speed is not in range of approx. 25 MPH (40 km/h) to 89 MPH (144 km/h).

When the A/T selector lever is in gears other than "D".

While the brake is in operation.

When the windshield wipers are operating.
1. CHECK CAUSE OF AUTOMATIC CANCELLATION
With CONSULT-II
1. With “CAUSE OF AUTO-CANCEL” in work support, check if any cause of cancellation exists.
OK or NG
OK >>
Cancel with appropriate cause.

For causes A, B, or C, go to specified diagnosis.
A: “OPE SW VOLT CIRC” : Refer to ACS-41, "
DTC 46 OPERATION SW CIRC" .
B: “VHCL SPD UNMATCH” : Refer to ACS-39, "
DTC 41 VHCL SPEED SE CIRC" .
C: “IGN LOW VOLT” : Refer to ACS-38, "
DTC 31 POWER SUPPLY CIR 1, DTC 34
POWER SUPPLY CIR 2" .
NG >> GO TO 2.

ACS-56
[ICC]
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: August 20072004 QX56
2. CAN COMMUNICATION INSPECTION
With CONSULT-II
1. With CONSULT-II self-diagnosis, check “CAN COMM CIRCUIT”.
OK or NG
OK >> Refer to ACS-38, "DTC 20 CAN COMM CIRCUIT" .
NG >> Replace combination meter and erase DTC. Refer to DI-25, "
Removal and Installation of Combi-
nation Meter" . Perform ICC system running test, and then perform self-diagnosis of ICC system
again.
Symptom 6: Driving Force Is HuntingEKS007XX
1. CHECK ECM
1. Perform self-diagnosis of ECM.
OK or NG
OK >> Refer to ACS-56, "Symptom 7: The ICC System Frequently Cannot Detect the Vehicle Ahead/The
Detection Zone is Short" .
NG >> After repairing applicable parts, erase DTC. Perform ICC system running test, and then perform
self-diagnosis of ICC system again.
Symptom 7: The ICC System Frequently Cannot Detect the Vehicle Ahead/The
Detection Zone is Short
EKS007XY
The detection function may become unstable in the following cases:

When the reflector of the vehicle ahead is small or not clean enough to reflect the laser.

When driving a road with extremely sharp corners.

When the laser cannot detect the reflector of the vehicle ahead as the vehicle ahead is passing a hill or
passing the peak.
1. VISUAL CHECK
1. Check ICC sensor body window for contamination and foreign materials.
OK or NG
OK >> If any contamination or foreign materials are found, remove them. Then perform ICC system run-
ning test.
NG >> GO TO 2.
2. CHECK FUNCTION
1. After performing laser beam aiming adjustment, perform ICC system running test. Check that preceding
vehicle detection performance has been improved.
OK or NG
OK >> Inspection End.
NG >>

Replace ICC sensor and perform laser beam aiming adjustment. Refer to ACS-59, "ICC Sen-
sor" .

After performing above, perform ICC system running test, and then perform self-diagnosis of
ICC system again.
Symptom 8: The System Does Not Detect the Vehicle Ahead at AllEKS007XZ
1. VISUAL CHECK
1. With ignition switch turned ON (engine not started), check that all indicator lamps in ICC system display
are continuously lit. (Check for a missing segment in preceding vehicle detection display.)
OK or NG
OK >> GO TO 2.
NG >> Check combination meter. Refer to DI-17, "
How to Proceed With Trouble Diagnosis" .

TROUBLE DIAGNOSIS FOR SYMPTOMS
ACS-57
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: August 20072004 QX56
2. VISUAL CHECK

Check ICC sensor body window for contamination and foreign materials.
OK or NG
OK >> If any contamination or foreign materials are found, remove them. Perform ICC system running
test. Refer to ACS-9, "
ICC System Running Test" .
NG >> GO TO 3.
3. VISUAL CHECK

Check ICC sensor body window for cracks and scratches.
OK or NG
OK >> GO TO 4.
NG >>

Replace ICC sensor and perform laser beam aiming adjustment. Refer to ACS-59, "ICC Sen-
sor" .

After performing above, perform ICC system running test, and then perform self-diagnosis of
ICC system again.
4. ADJUST ICC SENSOR

After performing laser beam aiming adjustment, perform ICC system running test. Check that preceding
vehicle detection performance has been improved.
OK or NG
OK >> Inspection End.
NG >>

Replace ICC sensor and perform laser beam aiming adjustment. Refer to ACS-59, "ICC Sen-
sor" .

After performing above, perform ICC system running test, and then perform self-diagnosis of
ICC system again.

ACS-58
[ICC]
ELECTRICAL COMPONENT INSPECTION
Revision: August 20072004 QX56
ELECTRICAL COMPONENT INSPECTIONPFP:00000
ICC Steering SwitchEKS007TT
1. Disconnect ICC steering switch.
2. Check resistance between M102 terminals 14 and 15 while
depressing each switch.
ICC Brake Switch and Stop Lamp SwitchEKS007TU
Check each switch after adjusting brake pedal. Refer to BR-6,
"BRAKE PEDAL" .
Parking Brake SwitchEKS007TX
Switch ConditionResistance [Ω]
(Approx.)
ON/OFF Depressed 0
Released 5,456
DISTANCE Depressed 741
Released 5,456
ACCEL/RES Depressed 2,586
Released 5,456
COAST/SET Depressed 1,406
Released 5,456
CANCEL Depressed 309
Released 5,456
WKIA1916E
Continuity
ICC brake switch Stop lamp switch
When brake pedal is depressed No Yes
When brake pedal is released Yes No
WKIA3405E
Continuity to ground
Parking brake pedal depressed Yes
Parking brake pedal released No
WKIA1918E

REMOVAL AND INSTALLATION
ACS-59
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: August 20072004 QX56
REMOVAL AND INSTALLATIONPFP:00000
ICC UnitEKS007TO
ICC SensorEKS007TP
CAUTION:
Perform the laser beam aiming procedure every time the ICC sensor is removed or installed.
ICC Steering SwitchEKS007TQ
Replace ICC steering switch as switch kit assembly. Refer to AV-47, "Removal and Installation of Steering
Wheel Audio Control Switches" .
WKIA1914E
WKIA1915E

ACS-60
[ICC]
REMOVAL AND INSTALLATION
Revision: August 20072004 QX56

AT-1
AUTOMATIC TRANSMISSION
C TRANSMISSION/TRANSAXLE
CONTENTS
D
E
F
G
H
I
J
K
L
M
SECTION AT
A
B
AT
Revision: August 20072004 QX56 INDEX FOR DTC ........................................................ 5
Alphabetical Index .................................................... 5
DTC No. Index ......................................................... 6
PRECAUTIONS .......................................................... 7
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 7
Precautions for On Board Diagnostic (OBD) System
of A/T and Engine .................................................... 7
Precautions .............................................................. 8
Service Notice or Precautions .................................. 9
Wiring Diagrams and Trouble Diagnosis .................. 9
PREPARATION ......................................................... 10
Special Service Tools ............................................. 10
Commercial Service Tools ...................................... 12
A/T FLUID ................................................................. 13
Changing A/T Fluid ................................................ 13
Checking A/T Fluid ................................................. 13
A/T Fluid Cooler Cleaning ...................................... 15
A/T CONTROL SYSTEM .......................................... 18
Cross-Sectional View (2WD models) ..................... 18
Cross-Sectional View (4WD models) ..................... 19
Shift Mechanism ..................................................... 20
TCM Function ......................................................... 31
CAN Communication .............................................. 32
Input/Output Signal of TCM .................................... 32
Line Pressure Control ............................................ 33
Shift Control ........................................................... 34
Lock-up Control ...................................................... 35
Engine Brake Control ............................................. 37
Control Valve .......................................................... 37
ON BOARD DIAGNOSTIC (OBD) SYSTEM ............ 39
Introduction ............................................................ 39
OBD-II Function for A/T System ............................. 39
One or Two Trip Detection Logic of OBD-II ............ 39
OBD-II Diagnostic Trouble Code (DTC) ................. 39
Malfunction Indicator Lamp (MIL) ........................... 42
TROUBLE DIAGNOSIS ............................................ 43
DTC Inspection Priority Chart ................................ 43
Fail-Safe ................................................................. 43How To Perform Trouble Diagnosis For Quick and
Accurate Repair ...................................................... 45
A/T Electrical Parts Location .................................. 50
Circuit Diagram ....................................................... 51
Wiring Diagram — AT — ........................................ 52
Inspections Before Trouble Diagnosis .................... 58
Check Before Engine is Started .............................. 62
Check at Idle ........................................................... 62
Cruise Test - Part 1 ................................................. 63
Cruise Test - Part 2 ................................................. 65
Cruise Test - Part 3 ................................................. 66
Vehicle Speed When Shifting Gears ...................... 67
Vehicle Speed When Performing and Releasing
Complete Lock-up .................................................. 67
Vehicle Speed When Performing and Releasing
Slip Lock-up ............................................................ 67
Symptom Chart ....................................................... 68
TCM Input/Output Signal Reference Values ........... 90
CONSULT-II Function (A/T) .................................... 91
DTC U1000 CAN COMMUNICATION LINE ............103
Description ............................................................103
On Board Diagnosis Logic ....................................103
Possible Cause .....................................................103
DTC Confirmation Procedure ...............................103
Diagnostic Procedure ...........................................104
DTC P0615 START SIGNAL CIRCUIT ...................105
Description ............................................................105
CONSULT-II Reference Value ..............................105
On Board Diagnosis Logic ....................................105
Possible Cause .....................................................105
DTC Confirmation Procedure ...............................105
Diagnostic Procedure ...........................................106
DTC P0700 TCM .....................................................108
Description ............................................................108
On Board Diagnosis Logic ....................................108
Possible Cause .....................................................108
DTC Confirmation Procedure ...............................108
Diagnostic Procedure ...........................................108
DTC P0705 PARK/NEUTRAL POSITION SWITCH .109
Description ............................................................109

AT-2Revision: August 20072004 QX56 CONSULT-II Reference Value ..............................109
On Board Diagnosis Logic ....................................109
Possible Cause .....................................................109
DTC Confirmation Procedure ...............................109
Diagnostic Procedure ...........................................110
DTC P0720 VEHICLE SPEED SENSOR A/T (REV-
OLUTION SENSOR) ...............................................112
Description ............................................................112
CONSULT-II Reference Value ..............................112
On Board Diagnosis Logic ....................................112
Possible Cause .....................................................112
DTC Confirmation Procedure ...............................112
Diagnostic Procedure ...........................................113
DTC P0725 ENGINE SPEED SIGNAL ...................115
Description ............................................................115
CONSULT-II Reference Value ..............................115
On Board Diagnosis Logic ....................................115
Possible Cause .....................................................115
DTC Confirmation Procedure ...............................115
Diagnostic Procedure ...........................................115
DTC P0740 TORQUE CONVERTER CLUTCH
SOLENOID VALVE .................................................118
Description ............................................................118
CONSULT-II Reference Value ..............................118
On Board Diagnosis Logic ....................................118
Possible Cause .....................................................118
DTC Confirmation Procedure ...............................118
Diagnostic Procedure ...........................................119
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP) .121
Description ............................................................121
CONSULT-II Reference Value ..............................121
On Board Diagnosis Logic ....................................121
Possible Cause .....................................................121
DTC Confirmation Procedure ...............................121
Diagnostic Procedure ...........................................122
DTC P0745 LINE PRESSURE SOLENOID VALVE .124
Description ............................................................124
CONSULT-II Reference Value ..............................124
On Board Diagnosis Logic ....................................124
Possible Cause .....................................................124
DTC Confirmation Procedure ...............................124
Diagnostic Procedure ...........................................125
DTC P1702 TRANSMISSION CONTROL MODULE
(RAM) ......................................................................127
Description ............................................................127
On Board Diagnosis Logic ....................................127
Possible Cause .....................................................127
DTC Confirmation Procedure ...............................127
Diagnostic Procedure ...........................................127
DTC P1703 TRANSMISSION CONTROL MODULE
(ROM) ......................................................................128
Description ............................................................128
On Board Diagnosis Logic ....................................128
Possible Cause .....................................................128
DTC Confirmation Procedure ...............................128
Diagnostic Procedure ...........................................128
DTC P1705 THROTTLE POSITION SENSOR .......129
Description ............................................................129
CONSULT-II Reference Value ..............................129On Board Diagnosis Logic .................................... 129
Possible Cause ..................................................... 129
DTC Confirmation Procedure ................................ 129
Diagnostic Procedure ............................................ 129
DTC P1710 A/T FLUID TEMPERATURE SENSOR
CIRCUIT .................................................................. 131
Description ............................................................ 131
CONSULT-II Reference Value ............................... 131
On Board Diagnosis Logic .................................... 131
Possible Cause ..................................................... 131
DTC Confirmation Procedure ................................ 131
Diagnostic Procedure ............................................ 132
Component Inspection .......................................... 133
DTC P1716 TURBINE REVOLUTION SENSOR .... 134
Description ............................................................ 134
CONSULT-II Reference Value ............................... 134
On Board Diagnosis Logic .................................... 134
Possible Cause ..................................................... 134
DTC Confirmation Procedure ................................ 134
Diagnostic Procedure ............................................ 135
DTC P1721 VEHICLE SPEED SENSOR MTR ....... 136
Description ............................................................ 136
CONSULT-II Reference Value ............................... 136
On Board Diagnosis Logic .................................... 136
Possible Cause ..................................................... 136
DTC Confirmation Procedure ................................ 136
Diagnostic Procedure ............................................ 137
DTC P1730 A/T INTERLOCK ................................. 139
Description ............................................................ 139
On Board Diagnosis Logic .................................... 139
Possible Cause ..................................................... 139
DTC Confirmation Procedure ................................ 139
Judgement of A/T Interlock ................................... 140
Diagnostic Procedure ............................................ 140
DTC P1731 A/T 1ST ENGINE BRAKING ............... 142
Description ............................................................ 142
CONSULT-II Reference Value ............................... 142
On Board Diagnosis Logic .................................... 142
Possible Cause ..................................................... 142
DTC Confirmation Procedure ................................ 142
Diagnostic Procedure ............................................ 143
DTC P1752 INPUT CLUTCH SOLENOID VALVE .. 145
Description ............................................................ 145
CONSULT-II Reference Value ............................... 145
On Board Diagnosis Logic .................................... 145
Possible Cause ..................................................... 145
DTC Confirmation Procedure ................................ 145
Diagnostic Procedure ............................................ 146
DTC P1754 INPUT CLUTCH SOLENOID VALVE
FUNCTION .............................................................. 148
Description ............................................................ 148
CONSULT-II Reference Value ............................... 148
On Board Diagnosis Logic .................................... 148
Possible Cause ..................................................... 148
DTC Confirmation Procedure ................................ 148
Diagnostic Procedure ............................................ 149
DTC P1757 FRONT BRAKE SOLENOID VALVE ... 151
Description ............................................................ 151
CONSULT-II Reference Value ............................... 151

AT-4Revision: August 20072004 QX56 A/T Does Not Shift: 2nd gear → 1st gear .............227
Vehicle Does Not Decelerate By Engine Brake ....230
SHIFT CONTROL SYSTEM ....................................233
Control Device Removal and Installation ..............233
Adjustment of A/T Position ...................................234
Checking of A/T Position ......................................234
A/T SHIFT LOCK SYSTEM .....................................236
Description ............................................................236
Shift Lock System Electrical Parts Location .........236
Wiring Diagram — A/T — SHIFT ..........................237
Shift Lock Control Unit Reference Values .............238
Component Inspection ..........................................239
ON-VEHICLE SERVICE ..........................................241
Control Valve With TCM and A/T Fluid Temperature
Sensor 2 ...............................................................241
Rear Oil Seal ........................................................252
AIR BREATHER HOSE ...........................................253
Removal and Installation ......................................253
TRANSMISSION ASSEMBLY ................................255
Removal and Installation (4x2) .............................255
Removal and Installation (4x4) .............................258
OVERHAUL .............................................................261
Components .........................................................261
Oil Channel ...........................................................269
Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings ..........................271
DISASSEMBLY .......................................................273
Disassembly .........................................................273REPAIR FOR COMPONENT PARTS ...................... 290
Oil Pump ............................................................... 290
Front Sun Gear, 3rd One-Way Clutch ................... 292
Front Carrier, Input Clutch, Rear Internal Gear ..... 295
Mid Sun Gear, Rear Sun Gear, High and Low
Reverse Clutch Hub .............................................. 300
High and Low Reverse Clutch .............................. 305
Direct Clutch ......................................................... 307
ASSEMBLY ............................................................. 309
Assembly (1) ......................................................... 309
Adjustment ............................................................ 322
Assembly (2) ......................................................... 324
SERVICE DATA AND SPECIFICATIONS (SDS) .... 331
General Specifications .......................................... 331
Vehicle Speed When Shifting Gears ..................... 331
Vehicle Speed When Performing and Releasing
Complete Lock-up ................................................. 332
Vehicle Speed When Performing and Releasing
Slip Lock-up .......................................................... 332
Stall Speed ............................................................ 332
Line Pressure ........................................................ 332
A/T Fluid Temperature Sensor .............................. 332
Turbine Revolution Sensor .................................... 332
Vehicle Speed Sensor A/T (Revolution Sensor) ... 332
Reverse brake ....................................................... 333
Total End Play ....................................................... 333

PRECAUTIONS
AT-7
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
UCS002C1
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WA RN ING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for On Board Diagnostic (OBD) System of A/T and EngineUCS002C2
The ECM has an on board diagnostic system. It will light up the malfunction indicator lamp (MIL) to warn the
driver of a malfunction causing emission deterioration.
CAUTION:

Be sure to turn the ignition switch “OFF” and disconnect the negative battery cable before any
repair or inspection work. The open/short circuit of related switches, sensors, solenoid valves,
etc. Will cause the MIL to light up.

Be sure to connect and lock the connectors securely after work. A loose (unlocked) connector will
cause the MIL to light up due to an open circuit. (Be sure the connector is free from water, grease,
dirt, bent terminals, etc.)

Be sure to route and secure the harnesses properly after work. Interference of the harness with a
bracket, etc. May cause the MIL to light up due to a short circuit.

Be sure to connect rubber tubes properly after work. A misconnected or disconnected rubber tube
may cause the MIL to light up due to a malfunction of the EGR system or fuel injection system, etc.

Be sure to erase the unnecessary malfunction information (repairs completed) from the TCM and
ECM before returning the vehicle to the customer.