lock INFINITI QX56 2004 Factory Repair Manual

AT-256
TRANSMISSION ASSEMBLY
Revision: August 20072004 QX56
8. Remove crankshaft position sensor (POS) from A/T assembly.
9. Remove fluid cooler tube.
10. Remove dust cover from converter housing part.
11. Turn crankshaft, and remove the four tightening bolts for drive
plate and torque converter.
CAUTION:
When turning crankshaft, turn it clockwise as viewed from
the front of the engine.
12. Support A/T assembly with a transmission jack.
CAUTION:
When setting the transmission jack, be careful not to allow
it to collide against the drain plug.
13. Remove cross member with power tool.
14. Remove air breather hose. Refer to AT-253, "
Removal and
Installation" .
15. Disconnect A/T assembly connector.
16. Remove A/T fluid indicator pipe from A/T assembly.
17. Plug up openings such as the fluid charging pipe hole, etc.
18. Remove the A/T assembly to engine bolts with power tool.
19. Remove A/T assembly from vehicle using Tool and a transmis-
sion jack.

Secure torque converter to prevent it from dropping.

Secure A/T assembly to a transmission jack.
INSPECTION
Installation and Inspection of Torque Converter

After inserting a torque converter to a transmission, be sure to
check dimension A to ensure it is within the reference value
limit.
LCIA0334E
Tool number : — (J-47002)
LCIA0335E
SCIA0499E
Dimension A : 24.0 mm (0.94 in) or more
SAT0 1 7B

TRANSMISSION ASSEMBLY
AT-257
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
INSTALLATION
Installation of the remaining components is in the reverse order of
the removal, while paying attention to the following work.

If removed install drive plate.
–Align dowel pin of crankshaft rear end with pin holes of each
parts to install.
–Install drive plate, reinforcement plate and pilot converter as
shown.
–Face chamfered or rounded edge side to crankshaft.
CAUTION:

When replacing an engine or transmission you must make
sure the dowels are installed correctly during re-assembly.

Improper alignment caused by missing dowels may cause
vibration, oil leaks or breakage of drivetrain components.

When installing transmission to the engine, attach the bolts in
accordance with the following standard.
*: No.2 bolt also secures air breather vent.
–Align the positions of tightening bolts for drive plate with those of
the torque converter, and temporarily tighten the bolts. Then,
tighten the bolts with the specified torque.
CAUTION:

When turning crankshaft, turn it clockwise as viewed from the front of the engine.

After converter is installed to drive plate, rotate crankshaft several turns and check to be sure that
transmission rotates freely without binding.

After completing installation, check fluid leakage, fluid level, and the positions of A/T. Refer to AT-13,
"Checking A/T Fluid" , AT-234, "Checking of A/T Position" , AT-234, "Adjustment of A/T Position" .
KBIA2494E
KBIA2537E
Bolt No. 1 2* 3
Number of bolts 4 1 4
Bolt length
“”mm (in)70 (2.76) 70 (2.76) 70 (2.76)
Tightening torque
N·m (kg-m, ft-lb)11 3
(12, 83)11 3
(12, 83)
LCIA0371E
LCIA0335E

TRANSMISSION ASSEMBLY
AT-259
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
8. Remove crankshaft position sensor (POS) from A/T assembly.
9. Disconnect A/T fluid cooler tube from A/T assembly.
10. Remove dust cover from converter housing part.
11. Turn crankshaft, and remove the four tightening bolts for drive
plate and torque converter.
CAUTION:
When turning crankshaft, turn it clockwise as viewed from
the front of the engine.
12. Support A/T assembly with a transmission jack.
CAUTION:
When setting the transmission jack, be careful not to allow
it to collide against the drain plug.
13. Remove cross member with power tool.
14. Tilt the transmission slightly to keep the clearance between body
and transmission, and then disconnect air breather hose from charging pipe. Refer to AT- 2 5 3 , "
Removal
and Installation" .
15. Disconnect A/T assembly connector and transfer unit connector.
16. Remove A/T fluid indicator pipe.
17. Plug up openings such as the fluid charging pipe hole, etc.
18. Remove A/T assembly to engine bolts with power tool.
19. Remove A/T assembly from vehicle using Tool and a transmis-
sion jack.

Secure torque converter to prevent it from dropping.

Secure A/T assembly to a transmission jack.
NOTE:
The actual special service Tool may differ from Tool shown.
20. Remove transfer from A/T assembly. Refer to TF-109,
"REMOVAL AND INSTALLATION" .
INSPECTION
Installation and Inspection of Torque Converter

After inserting a torque converter to a transmission, be sure to
check dimension A to ensure it is within the reference value
limit.
LCIA0334E
Tool number : — (J-47002)
LCIA0335E
SCIA0499E
Dimension A : 24.0 mm (0.94 in) or more
SAT0 1 7B

AT-260
TRANSMISSION ASSEMBLY
Revision: August 20072004 QX56
INSTALLATION
Installation of the remaining components is in the reverse order of
the removal, while paying attention to the following work.

If removed, install drive plate.
–Align dowel pin of crankshaft rear end with pin holes of each
parts to install.
–Install drive plate, reinforcement plate and pilot converter as
shown.
–Face chamfered or rounded edge side to crankshaft.
CAUTION:

When replacing an engine or transmission you must make
sure the dowels are installed correctly during re-assembly.

Improper alignment caused by missing dowels may cause
vibration, oil leaks or breakage of drivetrain components.

When installing transmission to the engine, attach the bolts in
accordance with the following standard.
*: No.2 bolt also secures air breather vent.
–Align the positions of tightening bolts for drive plate with those of
the torque converter, and temporarily tighten the bolts. Then,
tighten the bolts with the specified torque.
CAUTION:

When turning crankshaft, turn it clockwise as viewed from the front of the engine.

After converter is installed to drive plate, rotate crankshaft several turns and check to be sure that
transmission rotates freely without binding.

After completing installation, check fluid leakage, fluid level, and the positions of A/T. Refer to AT-13,
"Checking A/T Fluid" , AT-234, "Checking of A/T Position" , AT-234, "Adjustment of A/T Position" .
KBIA2494E
KBIA2537E
Bolt No. 1 2* 3
Number of bolts 4 1 4
Bolt length
“”mm (in)70 (2.76) 70 (2.76) 70 (2.76)
Tightening torque
N·m (kg-m, ft-lb)11 3
(12, 83)11 3
(12, 83)
LCIA0371E
LCIA0335E

DISASSEMBLY
AT-273
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
DISASSEMBLYPFP:31020
DisassemblyUCS002JJ
CAUTION:
Do not disassemble parts behind Drum Support. Refer to AT-18, "
Cross-Sectional View (2WD models)"
or AT- 1 9 , "Cross-Sectional View (4WD models)" .
1. Drain ATF through drain plug.
2. Remove torque converter by holding it firmly and turing while
pulling straight out.
3. Check torque converter one-way clutch using check tool as
shown at figure.
a. Insert check tool into the groove of bearing support built into
one-way clutch outer race.
b. When fixing bearing support with check tool, rotate one- way
clutch spline using screwdriver.
c. Check that inner race rotates clockwise only. If not, replace
torque converter assembly.
4. Remove converter housing from transmission case.
CAUTION:
Be careful not to scratch converter housing.
SCIA5010E
SCIA3171E
SCIA5171E

AT-276
DISASSEMBLY
Revision: August 20072004 QX56
14. Loosen lock nut and remove band servo anchor end pin from
transmission case.
15. Remove brake band from transmission case.

To prevent brake linings from cracking or peeling, do not
stretch the flexible band unnecessarily. When removing
the brake band, always secure it with a clip as shown in
the figure at left.
Leave the clip in position after removing the brake band.

Check brake band facing for damage, cracks, wear or
burns.
16. Remove mid carrier assembly and rear carrier assembly as a
unit.
SCIA5016E
SCIA5345E
SAT6 5 5
SCIA5344E

AT-294
REPAIR FOR COMPONENT PARTS
Revision: August 20072004 QX56
2. Using a flat-bladed screwdriver, install snap ring in front sun
gear.
3. Check operation of 3rd one-way clutch.
a. Hold oil pump assembly and turn front sun gear.
b. Check 3rd one-way clutch for correct locking and unlocking
directions.
CAUTION:
If not as shown in illustration, check installation direction of
3rd one-way clutch.
SCIA3 110 E
SCIA3131E

AT-304
REPAIR FOR COMPONENT PARTS
Revision: August 20072004 QX56
5. Install needle bearing to high and low reverse clutch hub.
CAUTION:

Take care with the direction of needle baering. Refer to
AT- 2 7 1 , "
Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings" .

Apply petroleum jelly to needle bearing.
6. Install high and low reverse clutch hub to mid sun gear assem-
bly.
7. Using a snap ring pliers, install snap ring to mid sun gear
assembly.
CAUTION:
Do not expand snap ring excessively.
8. Check operation of 1st one-way clutch.
a. Hold mid sun gear and turn rear sun gear.
b. Check 1st one-way clutch for correct locking and unlocking
directions.
CAUTION:
If not as shown in illustration, check installation direction of
1st one-way clutch.
9. Install needle bearing and bearing races to high and low reverse
clutch hub.
CAUTION:

Apply petroleum jelly to needle bearing and bearing
races.

Take care with order of bearing races.
SCIA2857E
SCIA2856E
SCIA2855E
SCIA3132E
SCIA5238E

ASSEMBLY
AT-321
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
48. Install band servo anchor end pin and lock nut in transmission
case.
CAUTION:
Do not reuse band servo anchor end pin.
49. Install brake band in transmission case.
CAUTION:
Assemble it so that identification to avoid incorrect installa-
tion faces servo side.
50. Install front sun gear assembly to front carrier assembly.
CAUTION:
Apply ATF to front sun gear radial bearing and 3rd one-way
clutch end bearing.
51. Install needle bearing in front sun gear assembly.
CAUTION:
Apply petroleum jelly to needle bearing.
52. Adjust brake band tilting using clips so that brake band contacts
front sun gear drum evenly.
SCIA5016E
SCIA2809E
SCIA5014E
SCIA2808E
SCIA5033E

AT-322
ASSEMBLY
Revision: August 20072004 QX56
53. Adjust brake band.
a. Loosen lock nut.
b. Tighten band servo anchor end pin to specified torque.
c. Back of band servo anchor end pin three turns.
d. Holding band servo anchor end pin, tighten lock nut to specified
torque. Refer to AT-261, "
Components" .
AdjustmentUCS002JR
TOTAL END PLAY

Measure clearance between front sun gear and bearing race for
oil pump cover.

Select proper thickness of bearing race so that end play is within
specifications.
1. Measure dimensions “K” and “L” and then calculate dimension
“J”.
a. Measure dimension “K”.: 5.0 N·m (0.51 kg-m, 44 in-lb)
SCIA2809E
SCIA2810E
SCIA5350E
SCIA5351E