sensor INFINITI QX56 2006 Factory Owner's Manual

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMSACS-49
[ICC]
C
DE
F
G H
I
J
L
M A
B
ACS
Revision: November 2009 2006 QX56
DTC 98 GEAR POSITIONEKS00BMD
1. DIAGNOSTIC CHECK
With CONSULT-II
Is “DTC 43 VDC/TCS/ABS CIRC ” or “DTC 41 VHCL SPEED SE CIRC ” indicated in self-diagnosis display
item?
YES or NO
YES >> Repair or replace as necessary. Erase DTC and perform self-diagnosis of ICC system again.
NO >> GO TO 2.
2. CHECK VEHICLE SPEED SIGNAL
With CONSULT-II
With data monitor, check that “VHCL SPEED SE” is normal.
OK or NG
OK >> GO TO 3.
NG >> Replace ICC unit. Refer to ACS-59, "
ICC Unit" . Erase DTC and perform self-diagnosis of ICC
system again.
3. CHECK GEAR SHIFT POSITION
Check that gear positions are correct in A/T.
OK or NG
OK >> GO TO 5.
NG >> GO TO 4.
4. CHECK TCM GEAR POSITION SIGNAL
With CONSULT-II
With TCM data monitor on CONSULT-II, check that gear positions are correct.
OK or NG
OK >> Replace ICC unit. Refer to ACS-59, "ICC Unit" . Erase DTC and perform self-diagnosis of ICC
system again.
NG >>

Perform TCM diagnosis.

Erase DTC and perform self-diagnosis of ICC system again.
5. CHECK TCM TURBINE ROTATION
With CONSULT-II
With TCM diagnosis, check that turbine rpm is normal. Refer to AT- 1 0 9 , "
DTC P0717 TURBINE REVOLU-
TION SENSOR" .
OK or NG
OK >> Replace ICC unit. Refer to ACS-59, "ICC Unit" . Erase DTC and perform self-diagnosis of ICC
system again.
NG >>

Perform TCM diagnosis.

Erase DTC and perform self-diagnosis of ICC system again.
DTC 102 LASER STAINEKS00BME
1. VISUAL INSPECTION (1)
Check that there is no contamination and foreign material on ICC sensor body window.
OK or NG
OK >> GO TO 2.
NG >>

Clean ICC sensor.

Erase DTC and perform ICC system running test. Refer to ACS-9, "ICC System Running Test"
. Then perform self-diagnosis of ICC system again.

ACS-50
[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: November 20092006 QX56
2. VISUAL INSPECTION (2)
Check ICC sensor body window for cracks.
OK or NG
OK >> GO TO 3.
NG >>

Replace ICC sensor and adjust laser beam. Refer to ACS-12, "LASER BEAM AIMING
ADJUSTMENT" .

Erase DTC and perform ICC system running test. Refer to ACS-9, "ICC System Running Test"
. Then perform self-diagnosis of ICC system again.
3. ASK CUSTOMER FOR DRIVING CONDITIONS
1. Is there any trace of contamination or foreign material on ICC sensor?
2. Is there any possibility that vehicle was driven in snow or ICC sensor was frosted?
3. Is there any possibility that ICC sensor was fogged temporarily? (Front window glass may have also been fogged.)
Ye s o r N o
Yes >> Explain system operation and parameters to customer. System may be operating normally.
No >>

Replace ICC sensor and adjust laser beam aiming. Refer to ACS-59, "ICC Sensor" .

Erase DTC and perform ICC system running test. Refer to ACS-9, "ICC System Running Test"
. Then perform self-diagnosis of ICC system again.
DTC 103 LASER SENSOR FAILEKS00BMF
1. DIAGNOSTIC CHECK
Are “DTC 11 CONTROL UNIT ” or “DTC 20 CAN COMM CIRCUIT ” item indicated in self-diagnosis display
item?
YES or NO
YES >> GO TO applicable item inspection. Refer to ACS-37, "DTC 11 CONTROL UNIT" , and ACS-38,
"DTC 20 CAN COMM CIRCUIT" .
NO >>

Replace ICC sensor and adjust laser beam aiming. Refer to ACS-59, "ICC Sensor" .

Erase DTC and perform ICC system running test. Refer to ACS-9, "ICC System Running Test"
. Then perform self-diagnosis of ICC system again.
DTC 104 LASER AIMING INCMPEKS00BMG
1. DIAGNOSTIC CHECK
1. Adjust laser beam aiming. Refer to ACS-12, "
LASER BEAM AIMING ADJUSTMENT" . Erase DTC and
perform ICC system running test. Refer to ACS-9, "
ICC System Running Test" .
2. Perform self-diagnosis of ICC system. Is “DTC 104 LASER AIMING INCMP” indicated?
CAUTION:
Ensure that laser beam aiming apparatus is set up accurately.
YES or NO
YES >>
Replace ICC sensor and adjust laser beam aiming. Refer to ACS-59, "ICC Sensor" .

Erase DTC and perform ICC system running test. Refer to ACS-9, "ICC System Running Test"
. Then perform self-diagnosis of ICC system again.
NO >> Inspection end.

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMSACS-51
[ICC]
C
DE
F
G H
I
J
L
M A
B
ACS
Revision: November 2009 2006 QX56
DTC 107 LASER COMM FAILEKS00BMH
1. DIAGNOSTIC CHECK
Is “DTC 11 CONTROL UNIT ” or “DTC 20 CAN COMM CIRCUIT ” indicated in the self-diagnosis display item?
YES or NO
YES >> GO TO applicable item inspection. Refer to ACS-37, "DTC 11 CONTROL UNIT" , or ACS-38,
"DTC 20 CAN COMM CIRCUIT" .
NO >>

Replace ICC sensor and adjust laser beam aiming. Refer to ACS-59, "ICC Sensor" .

Erase DTC and perform ICC system running test. Refer to ACS-9, "ICC System Running Test"
. Then perform self-diagnosis of ICC system again.
DTC 109 LASER HIGH TEMPEKS00BMI
1. CHECK SYMPTOM
Is cooling system malfunctioning?
YES or NO
YES >>
Repair cooling system.

Erase DTC and perform ICC system running test. Refer to ACS-9, "ICC System Running Test"
. Then perform self-diagnosis of ICC system again.
NO >>

Replace ICC sensor and adjust laser beam aiming. Refer to ACS-59, "ICC Sensor" .

Erase DTC, then perform ICC system running test. Refer to ACS-9, "ICC System Running Test"
. Then perform self-diagnosis of ICC system again.

ACS-56
[ICC]
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: November 20092006 QX56
2. CAN COMMUNICATION INSPECTION
With CONSULT-II
1. With CONSULT-II self-diagnosis, check “CAN COMM CIRCUIT”.
OK or NG
OK >> Refer to ACS-38, "DTC 20 CAN COMM CIRCUIT" .
NG >> Replace combination meter. Refer to IP-13, "
COMBINATION METER" . Erase DTC and perform
ICC system running test. Refer to ACS-9, "
ICC System Running Test" . Then perform self-diagno-
sis of ICC system again.
Symptom 6: Driving Force Is HuntingEKS00BMP
1. CHECK ECM
1. Perform self-diagnosis of ECM.
OK or NG
OK >> Refer to ACS-56, "Symptom 7: The ICC System Frequently Cannot Detect the Vehicle Ahead/The
Detection Zone is Short" .
NG >> Repair as necessary. Erase DTC and perform ICC system running test. Refer to ACS-9, "
ICC
System Running Test" . Then perform self-diagnosis of ICC system again.
Symptom 7: The ICC System Frequently Cannot Detect the Vehicle Ahead/The
Detection Zone is Short
EKS00BMQ
The detection function may become disrupted in the following cases:

When the reflector of the vehicle ahead is small or not clean enough to reflect the laser.

When driving a road with extremely sharp corners.

When the laser cannot detect the reflector of the vehicle ahead as the vehicle ahead is passing a hill or
passing the peak.
1. VISUAL CHECK
1. Check ICC sensor body window for contamination and foreign materials.
OK or NG
OK >> If any contamination or foreign materials are found, remove them. Then perform ICC system run- ning test. Refer to ACS-9, "
ICC System Running Test" .
NG >> GO TO 2.
2. CHECK FUNCTION
1. After performing laser beam aiming adjustment, perform ICC system running test. Refer to ACS-9, "
ICC
System Running Test" . Check that preceding vehicle detection performance has been improved.
OK or NG
OK >> Inspection End.
NG >>

Replace ICC sensor and perform laser beam aiming adjustment. Refer to ACS-59, "ICC Sen-
sor" .

Perform ICC system running test. Refer to ACS-9, "ICC System Running Test" . Then perform
self-diagnosis of ICC system again.
Symptom 8: The System Does Not Detect the Vehicle Ahead at AllEKS00BMR
1. VISUAL CHECK
1. With ignition switch turned ON (engine not started), check that all indicator lamps in ICC system display are continuously lit. (Check for a missing segment in preceding vehicle detection display.)
OK or NG
OK >> GO TO 2.
NG >> Check combination meter. Refer to DI-17, "
How to Proceed With Trouble Diagnosis" .

TROUBLE DIAGNOSIS FOR SYMPTOMSACS-57
[ICC]
C
DE
F
G H
I
J
L
M A
B
ACS
Revision: November 2009 2006 QX56
2. VISUAL CHECK

Check ICC sensor body window for contamination and foreign materials.
OK or NG
OK >> If any contamination or foreign materials are found, remove them. Perform ICC system running test. Refer to ACS-9, "
ICC System Running Test" .
NG >> GO TO 3.
3. VISUAL CHECK

Check ICC sensor body window for cracks and scratches.
OK or NG
OK >> GO TO 4.
NG >>

Replace ICC sensor and perform laser beam aiming adjustment. Refer to ACS-59, "ICC Sen-
sor" .

Perform ICC system running test. Refer to ACS-9, "ICC System Running Test" . Then perform
self-diagnosis of ICC system again.
4. ADJUST ICC SENSOR

After performing laser beam aiming adjustment, perform ICC system running test. Refer to ACS-9, "ICC
System Running Test" . Check that preceding vehicle detection performance has been improved.
OK or NG
OK >> Inspection End.
NG >>

Replace ICC sensor and perform laser beam aiming adjustment. Refer to ACS-59, "ICC Sen-
sor" .

Perform ICC system running test. Refer to ACS-9, "ICC System Running Test" . Then perform
self-diagnosis of ICC system again.

REMOVAL AND INSTALLATIONACS-59
[ICC]
C
DE
F
G H
I
J
L
M A
B
ACS
Revision: November 2009 2006 QX56
REMOVAL AND INSTALLATIONPFP:00000
ICC UnitEKS00BMV
ICC SensorEKS00BMW
CAUTION:
Perform the laser beam aiming procedure every time the ICC sensor is removed or installed. Refer to
ACS-12, "
LASER BEAM AIMING ADJUSTMENT" .
ICC Steering SwitchEKS00BMX
Replace ICC steering switch as switch kit assembly. Refer to AV- 5 9 , "STEERING WHEEL AUDIO CONTROL
SWITCHES" .
1. Rear inner side panel LH (shown
with finisher removed) 2. ICC unit harness connector 3. ICC unit
⇐ Vehicle front
WKIA4607E
1. ICC sensor bracket 2. ICC frame bracket3. ICC sensor
4. Frame side rail ⇐Vehicle front
WKIA4608E

AT-2Revision: November 20092006 QX56
CONSULT-II Reference Value .............................
.105
On Board Diagnosis Logic ................................... .105
Possible Cause .................................................... .105
DTC Confirmation Procedure .............................. .105
Wiring Diagram — AT — PNP/SW ...................... .106
Diagnostic Procedure .......................................... .107
DTC P0717 TURBINE REVOLUTION SENSOR ... .109
Description ........................................................... .109
CONSULT-II Reference Value ............................. .109
On Board Diagnosis Logic ................................... .109
Possible Cause .................................................... .109
DTC Confirmation Procedure .............................. .109
Diagnostic Procedure .......................................... .110
DTC P0720 VEHICLE SPEED SENSOR A/T (REV-
OLUTION SENSOR) .............................................. . 111
Description ........................................................... ..111
CONSULT-II Reference Value ...............................111
On Board Diagnosis Logic ................................... ..111
Possible Cause ......................................................111
DTC Confirmation Procedure .............................. ..111
Wiring Diagram — AT — VSSA/T ........................ .113
Diagnostic Procedure .......................................... .114
DTC P0725 ENGINE SPEED SIGNAL .................. .116
Description ........................................................... .116
CONSULT-II Reference Value ............................. .116
On Board Diagnosis Logic ................................... .116
Possible Cause .................................................... .116
DTC Confirmation Procedure .............................. .116
Diagnostic Procedure .......................................... .116
DTC P0740 TORQUE CONVERTER CLUTCH
SOLENOID VALVE ................................................ .118
Description ........................................................... .118
CONSULT-II Reference Value ............................. .118
On Board Diagnosis Logic ................................... .118
Possible Cause .................................................... .118
DTC Confirmation Procedure .............................. .118
Diagnostic Procedure .......................................... .119
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP) .120
Description ........................................................... .120
CONSULT-II Reference Value ............................. .120
On Board Diagnosis Logic ................................... .120
Possible Cause .................................................... .120
DTC Confirmation Procedure .............................. .120
Diagnostic Procedure .......................................... .121
DTC P0745 LINE PRESSURE SOLENOID VALVE .122
Description ........................................................... .122
CONSULT-II Reference Value ............................. .122
On Board Diagnosis Logic ................................... .122
Possible Cause .................................................... .122
DTC Confirmation Procedure .............................. .122
Diagnostic Procedure .......................................... .123
DTC P1705 THROTTLE POSITION SENSOR ...... .124
Description ........................................................... .124
CONSULT-II Reference Value ............................. .124
On Board Diagnosis Logic ................................... .124
Possible Cause .................................................... .124
DTC Confirmation Procedure .............................. .124
Diagnostic Procedure .......................................... .124
DTC P1710 A/T FLUID TEMPERATURE SENSOR CIRCUIT .................................................................
.127
Description ........................................................... .127
CONSULT-II Reference Value .............................. .127
On Board Diagnosis Logic ................................... .127
Possible Cause .................................................... .127
DTC Confirmation Procedure ............................... .127
Wiring Diagram — AT — FTS .............................. .128
Diagnostic Procedure ........................................... .129
Component Inspection ......................................... .130
DTC P1721 VEHICLE SPEED SENSOR MTR ...... .132
Description ........................................................... .132
CONSULT-II Reference Value .............................. .132
On Board Diagnosis Logic ................................... .132
Possible Cause .................................................... .132
DTC Confirmation Procedure ............................... .132
Diagnostic Procedure ........................................... .133
DTC P1730 A/T INTERLOCK ................................ .134
Description ........................................................... .134
On Board Diagnosis Logic ................................... .134
Possible Cause .................................................... .134
DTC Confirmation Procedure ............................... .134
Judgement of A/T Interlock .................................. .135
Diagnostic Procedure ........................................... .135
DTC P1731 A/T 1ST ENGINE BRAKING .............. .137
Description ........................................................... .137
CONSULT-II Reference Value .............................. .137
On Board Diagnosis Logic ................................... .137
Possible Cause .................................................... .137
DTC Confirmation Procedure ............................... .137
Diagnostic Procedure ........................................... .138
DTC P1752 INPUT CLUTCH SOLENOID VALVE . .139
Description ........................................................... .139
CONSULT-II Reference Value .............................. .139
On Board Diagnosis Logic ................................... .139
Possible Cause .................................................... .139
DTC Confirmation Procedure ............................... .139
Diagnostic Procedure ........................................... .140
DTC P1754 INPUT CLUTCH SOLENOID VALVE
FUNCTION ............................................................. .141
Description ........................................................... .141
CONSULT-II Reference Value .............................. .141
On Board Diagnosis Logic ................................... .141
Possible Cause .................................................... .141
DTC Confirmation Procedure ............................... .141
Diagnostic Procedure ........................................... .142
DTC P1757 FRONT BRAKE SOLENOID VALVE .. .143
Description ........................................................... .143
CONSULT-II Reference Value .............................. .143
On Board Diagnosis Logic ................................... .143
Possible Cause .................................................... .143
DTC Confirmation Procedure ............................... .143
Diagnostic Procedure ........................................... .144
DTC P1759 FRONT BRAKE SOLENOID VALVE
FUNCTION ............................................................. .145
Description ........................................................... .145
CONSULT-II Reference Value .............................. .145
On Board Diagnosis Logic ................................... .145
Possible Cause .................................................... .145

AT-4Revision: November 20092006 QX56
Shift Lock Control Unit Reference Values ............
.223
Component Inspection ......................................... .224
SHIFT CONTROL SYSTEM ................................... .226
Control Device Removal and Installation ............. .226
Adjustment of A/T Position .................................. .227
Checking of A/T Position ..................................... .227
ON-VEHICLE SERVICE ......................................... .228
Oil Pan ................................................................. .228
Control Valve With TCM and A/T Fluid Temperature
Sensor 2 .............................................................. .230
Rear Oil Seal ....................................................... .240
AIR BREATHER HOSE .......................................... .241
Removal and Installation ..................................... .241
TRANSMISSION ASSEMBLY ............................... .243
Removal and Installation (2WD) .......................... .243
Removal and Installation (4WD) .......................... .246
OVERHAUL ............................................................ .250
Components ........................................................ .250
Oil Channel .......................................................... .258
Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings ......................... .260
DISASSEMBLY ...................................................... .264
Disassembly ........................................................ .264
REPAIR FOR COMPONENT PARTS ..................... .282
Oil Pump .............................................................. .282Front Sun Gear, 3rd One-Way Clutch ..................
.284
Front Carrier, Input Clutch, Rear Internal Gear .... .286
Mid Sun Gear, Rear Sun Gear, High and Low
Reverse Clutch Hub ............................................. .291
High and Low Reverse Clutch ............................. .296
Direct Clutch ........................................................ .298
ASSEMBLY ............................................................ .300
Assembly (1) ........................................................ .300
Adjustment ........................................................... .313
Assembly (2) ........................................................ .316
SERVICE DATA AND SPECIFICATIONS (SDS) ... .323
General Specifications ......................................... .323
Vehicle Speed When Shifting Gears .................... .323
Vehicle Speed When Performing and Releasing
Complete Lock-up ................................................ .324
Vehicle Speed When Performing and Releasing
Slip Lock-up ......................................................... .324
Stall Speed ........................................................... .324
Line Pressure ....................................................... .324
A/T Fluid Temperature Sensor ............................. .324
Turbine Revolution Sensor ................................... .324
Vehicle Speed Sensor A/T (Revolution Sensor) .. .324
Reverse brake ...................................................... .325
Total End Play ...................................................... .325

PRECAUTIONSAT-7
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
ECS00CDJ
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER ”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for On Board Diagnostic (OBD) System of A/T and EngineECS00CDK
The ECM has an on board diagnostic system. It will light up the malfunction indicator lamp (MIL) to warn the
driver of a malfunction causing emission deterioration.
CAUTION:

Be sure to turn the ignition switch “OFF” and disconnect the negative battery cable before any
repair or inspection work. The open/short circuit of related switches, sensors, solenoid valves,
etc. Will cause the MIL to light up.

Be sure to connect and lock the connectors securely after work. A loose (unlocked) connector will
cause the MIL to light up due to an open circuit. (Be sure the connector is free from water, grease,
dirt, bent terminals, etc.)

Be sure to route and secure the harnesses properly after work. Interference of the harness with a
bracket, etc. May cause the MIL to light up due to a short circuit.

Be sure to connect rubber tubes properly after work. A misconnected or disconnected rubber tube
may cause the MIL to light up due to a malfunction of the EGR system or fuel injection system, etc.

Be sure to erase the unnecessary malfunction information (repairs completed) from the TCM and
ECM before returning the vehicle to the customer.

AT-30
A/T CONTROL SYSTEM
Revision: November 20092006 QX56
TCM FunctionECS00CDW
The function of the TCM is to:

Receive input signals sent from various switches and sensors.

Determine required line pressure, shifting point, lock-up operation, and engine brake operation.

Send required output signals to the respective solenoids.
CONTROL SYSTEM OUTLINE
The automatic transmission senses vehicle operating conditions through various sensors or signals. It always
controls the optimum shift position and reduces shifting and lock-up shocks.
CONTROL SYSTEM DIAGRAM
SENSORS (or SIGNALS)

TCM

ACTUATORS
PNP switch
Accelerator pedal position sensor
Closed throttle position signal
Wide open throttle position signal
Engine speed signal
A/T fluid temperature sensor
Revolution sensor
Vehicle speed signal
Stop lamp switch signal
Turbine revolution sensor
1st position switch signal
4th position switch signal
ATF pressure switch signal
Tow mode switch signal Shift control
Line pressure control
Lock-up control
Engine brake control
Timing control
Fail-safe control
Self-diagnosis
CONSULT-II communication line
Duet-EA control
CAN system
Input clutch solenoid valve
Direct clutch solenoid valve
Front brake solenoid valve
High and low reverse clutch
solenoid valve
Low coast brake solenoid valve
Torque converter clutch solenoid
valve
Line pressure solenoid valve
A/T CHECK indicator lamp
Starter relay
Back-up lamp relay
SCIA5624E