display INFINITI QX56 2011 Factory Service Manual

CCS
C1A26 ECD MODE MALFUNCTIONCCS-115
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
C1A26 ECD MODE MALFUNCTION
DTC LogicINFOID:0000000006224347
DTC DETECTION LOGIC
NOTE:
If DTC “C1A26” is detected along with DTC “U1000” , “U0415” or “U0121” first diagnose the DTC “U1000”,
“U0415” or “U0121”.
 DTC “U1000”: Refer to CCS-145, "
ADAS CONTROL UNIT : DTC Logic".
 DTC “U0415”: Refer to CCS-141, "
ADAS CONTROL UNIT : DTC Logic".
 DTC “U0121”: Refer to CCS-133, "
ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Wait for approximately 1 minute after turn ing the MAIN switch of ICC system ON.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “C1A26” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“C1A26” detected as the current malfunction?
YES >> Refer to CCS-115, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006224348
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000”, “U0415” or “U0121” is detected other than “C1A26” in “Self Diagnostic Result” of “ICC/
ADAS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
CCS-50, "
DTC Index".
NO >> GO TO 2.
2.PERFORM SELF-DIAGNOSIS OF ABS ACTUAT OR AND ELECTRIC UNIT (CONTROL UNIT)
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
BRC-51, "
DTC Index".
NO >> Replace ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board display) Trouble diagnosis name DTC detecting condition Possible cause
C1A26 (26) ECD MODE MALF If an abnormal condition occurs with ECD system ABS actuator and electric unit (control
unit)
Revision: 2010 May2011 QX56

CCS-116
< DTC/CIRCUIT DIAGNOSIS >[ICC]
C1A27 ECD POWER SUPPLY CIRCUIT
C1A27 ECD POWER SUPPLY CIRCUIT
DTC LogicINFOID:0000000006224349
DTC DETECTION LOGIC
NOTE:
If DTC “C1A27” is detected along with DTC “U1000”
, “U0415” or “U0121” first diagnose the DTC “U1000”,
“U0415” or “U0121”.
 DTC “U1000”: Refer to CCS-145, "
ADAS CONTROL UNIT : DTC Logic".
 DTC “U0415”: Refer to CCS-141, "
ADAS CONTROL UNIT : DTC Logic".
 DTC “U0121”: Refer to CCS-133, "
ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Wait for approximately 1 minute after turn ing the MAIN switch of ICC system ON.
3. Perform “All DTC Reading” with CONSULT-III.
4. Check if the “C1A27” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“C1A27” detected as the current malfunction?
YES >> Refer to CCS-116, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006224350
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000”, “U0415” or “U0121” is detected other than “C1A27” in “Self Diagnostic Result” of “ICC/
ADAS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
CCS-50, "
DTC Index".
NO >> GO TO 2.
2.CHECK POWER SUPPLY CIRCUIT OF ABS ACTU ATOR AND ELECTRIC UNIT (CONTROL UNIT)
Check power supply circuit of ABS actuator and electric unit (control unit). Refer to BRC-113, "
Diagnosis Pro-
cedure".
Is the inspection result normal?
YES >> Perform self-diagnosis of ABS actuator and electric unit (control unit). Refer to BRC-51, "DTC
Index".
NO >> Repair the harnesses or connectors.
DTC
(On board display) Trouble diagnosis name DTC detecting condition Possible cause
C1A27 (27) ECD PWR SUPLY CIR ECD system power supply voltage is excessively
low  ABS actuator and electric unit (con-
trol unit) power supply circuit
 ABS actuator and electric unit (con- trol unit)
Revision: 2010 May2011 QX56

CCS
C1A2A ICC SENSOR POWER SUPPLY CIRCUITCCS-117
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
C1A2A ICC SENSOR POWER SUPPLY CIRCUIT
DTC LogicINFOID:0000000006224351
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the MAIN switch of ICC system ON.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “C1A2A” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“C1A2A” detected as the current malfunction?
YES >> Refer to CCS-117, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006224352
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “C1A2A ” in “Self Diagnostic Result” of “ICC/ADAS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
CCS-145, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ICC SENSOR SELF-DIAGNOSIS
Check if any DTC is detected in “Self Diagnostic Result” of “LASER”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
CCS-55, "
DTC Index".
NO >> Replace ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board display) Trouble diagnosis name DTC detecting condition Possible cause
C1A2A (80) ICC SEN PWR SUP CIR Abnormal powe
r supply voltage in ICC sensor Harness, connector, fuse
 ICC sensor
Revision: 2010 May2011 QX56

CCS
C1F05 ACCELERATOR PEDAL ACTUATOR POWER SUPPLY CIRCUIT
CCS-131
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
C1F05 ACCELERATOR PEDAL ACTU ATOR POWER SUPPLY CIRCUIT
DTC LogicINFOID:0000000006224378
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the DCA system ON.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “C1F05” is detected as the current malfunction on the self-diagnosis results of “ICC/ADAS”.
Is
“C1F05” detected as the current malfunction?
YES >> Refer to CCS-131, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006224379
1.CHECK ADAS CONTROL UNIT SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “C1F05” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communicati on system inspection. Repair or replace the malfunctioning parts.
Refer to CCS-145, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ACCELERATOR PEDAL ACTU ATOR SELF-DIAGNOSIS RESULTS
Check if “C1F05” is detected in “Self Diagnostic Result” of “ACCELE PEDAL ACT”.
Is
“C1F05” detected?
YES >> Refer to DAS-171, "ACCELERATOR PEDAL ACTUATOR : DTC Logic".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board
display) Trouble diagnosis name DTC detecting condition Possible causes
C1F05 (95) APA PWR SUPLY CIR The battery voltage sent to accelerator pedal
actuator remains less than 7.9 V or more than
19.3 V for 5 seconds  Harness, connector, or fuse
 Accelerator pedal actuator
Revision: 2010 May2011 QX56

CCS-138
< DTC/CIRCUIT DIAGNOSIS >[ICC]
U0401 ECM CAN 1
U0401 ECM CAN 1
DTC LogicINFOID:0000000006224392
DTC DETECTION LOGIC
NOTE:
If DTC “U0401” is detected along with DTC “U1000”, first diagnose the DTC “U1000”. Refer to
CCS-145,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the MAIN switch of ICC system ON.
3. Perform “All DTC Reading” with CONSULT-III.
4. Check if the “U0401” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U0401” detected as the current malfunction?
YES >> Refer to CCS-138, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006224393
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected ot her than “U0401” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communication system inspecti on. Repair or replace the malfunctioning parts.
Refer to CCS-145, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ECM SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “S elf Diagnostic Result” of “ENGINE”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
EC-98, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board
display) Trouble diagnosis name DTC detecting condition Possible causes
U0401 (120) ECM CAN CIR1 If ADAS control unit detects an error signal
that is received from ECM via CAN communi-
cation
ECM
Revision: 2010 May2011 QX56

CCS
U1000 CAN COMM CIRCUITCCS-145
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
U1000 CAN COMM CIRCUIT
ADAS CONTROL UNIT
ADAS CONTROL UNIT : DescriptionINFOID:0000000006227995
CAN COMMUNICATION
CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-vehicle mul-
tiplex communication line with high data communicati on speed and excellent error detection ability. Modern
vehicle is equipped with many electronic control units , and each control unit shares information and links with
other control units during operation (not independent). In CAN communication, control units are connected
with 2 communication lines (CAN-H, CAN-L) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads the required data only.
CAN communication signal chart. Refer to LAN-28, "
CAN COMMUNICATION SYSTEM : CAN Communica-
tion Signal Chart".
ITS COMMUNICATION
 ITS communication is a multiplex communication syste m. This enables the system to transmit and receive
large quantities of data at high speed by connec ting control units with 2 communication lines.
 ITS communication lines adopt twisted-pair line st yle (two lines twisted) for noise immunity.
ADAS CONTROL UNIT : DTC LogicINFOID:0000000006227996
DTC DETECTION LOGIC
NOTE:
If “U1000” is detected, first diagnose the CAN communication system.
ADAS CONTROL UNIT : Diagnosis ProcedureINFOID:0000000006227997
1.PERFORM THE SELF-DIAGNOSIS
1. Turn the ignition switch ON.
2. Turn the MAIN switch of ICC system ON, and then wait for 30 seconds or more.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “U1000” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected as the current malfunction?
YES >> Refer to LAN-18, "Trouble Diagnosis Flow Chart".
NO >> Refer to GI-40, "
Intermittent Incident".
ICC SENSOR
ICC SENSOR : DescriptionINFOID:0000000006224409
ITS COMMUNICATION
 ITS communication is a multiplex communication syste m. This enables the system to transmit and receive
large quantities of data at high speed by connec ting control units with 2 communication lines
 ITS communication lines adopt twisted-pair line st yle (two lines twisted) for noise immunity.
ICC SENSOR : DTC LogicINFOID:0000000006224410
DTC DETECTION LOGIC
DTC
(On board
display) Trouble diagnosis name DTC detecting condition Possible causes
U1000 (100) CAN COMM CIRCUIT If ADAS control unit is not transmitting or receiv-
ing CAN communication signal or ITS communi-
cation signal for 2 seconds or more  CAN communication system
 ITS communication system
Revision: 2010 May2011 QX56

CCS
U1010 CONTROL UNIT (CAN)CCS-147
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
U1010 CONTROL UNIT (CAN)
ADAS CONTROL UNIT
ADAS CONTROL UNIT : DescriptionINFOID:0000000006227998
CAN controller controls the communication of CA N communication signal and ITS communication signal, and
the error detection.
ADAS CONTROL UNIT : DTC LogicINFOID:0000000006227999
DTC DETECTION LOGIC
ADAS CONTROL UNIT : Diagnosis ProcedureINFOID:0000000006228000
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn the MAIN switch of ICC system ON.
2. Perform “All DTC Readi ng” with CONSULT-III.
3. Check if the “U1010” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1010” detected as the current malfunction?
YES >> Replace the ADAS control unit. Refer to DAS-63, "Removal and Installation".
NO >> INSPECTION END
ICC SENSOR
ICC SENSOR : DescriptionINFOID:0000000006224415
CAN controller controls the communication of ITS communication signal and the error detection.
ICC SENSOR : DTC LogicINFOID:0000000006224416
DTC DETECTION LOGIC
ICC SENSOR : Diagnosis ProcedureINFOID:0000000006224417
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn the MAIN switch of ICC system ON.
2. Perform “All DTC Readi ng” with CONSULT-III.
3. Check if the “U1010” is detected as the current malfunction in “Self Diagnostic Result” of “LASER”.
Is
“U1010” detected as the current malfunction?
YES >> Replace the ICC sensor. Refer to CCS-176, "Exploded View".
NO >> INSPECTION END
DTC
(On board display) Trouble diagnosis name DTC detecting condition Possible causes
U1010 (110) CONTROL UNIT (CAN) If ADAS control unit detects malfunction by
CAN controller initial diagnosis ADAS control unit
DTC Trouble diagnosis name DTC detecting condition Possible causes
U1010 CONTROL UNIT (CAN) If ICC sensor detects malfunction by CAN con-
troller initial diagnosis ICC sensor
Revision: 2010 May2011 QX56

CCS-160
< SYMPTOM DIAGNOSIS >[ICC]
INTELLIGENT CRUISE CONT
ROL SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
INTELLIGENT CRUISE CONTROL SYSTEM SYMPTOMS
Symptom TableINFOID:0000000006224440
Symptoms Reference page
Operation MAIN switch does not turn ON
Refer to CCS-161, "
Description"MAIN switch does not turn OFF
ICC system cannot be set (MAIN switch turns
ON/OFF) Refer to
CCS-162, "
Description"
CANCEL switch does not function
Refer to CCS-164, "
Description"
Resume does not function
Set speed does not increase
Set distance to a vehicle ahead cannot be
changed
ICC is not canceled when the A/T selector lever
is “N” position Refer to
CCS-165, "
Description"
Display/Chime ICC system display not appear Refer to
MWI-29, "On Board Diagnosis Function"
Chime does not sound Refer to CCS-166, "Description"
Control Driving force is hunting Refer to CCS-168, "Description"
Function to detect
a vehicle aheadSystem frequently cannot detect a vehicle ahead
Refer to CCS-169, "
Description"Distance to detect a vehicle ahead is short
System misidentifies a vehicle even though there
is no vehicle ahead  Adjust laser beam aiming: Refer to
CCS-72, "
Descrip-
tion"
 Perform ICC system action test. Refer to CCS-77, "
De-
scription"System misidentifies a vehicle in the next lane
System does not detect a vehicle at all Refer to CCS-171, "
Description"
Revision: 2010 May2011 QX56

CCS
MAIN SWITCH DOES NOT TURN ON, MAIN SWITCH DOES NOT TURN OFF
CCS-161
< SYMPTOM DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
MAIN SWITCH DOES NOT TURN ON, MAIN SWITCH DOES NOT TURN
OFF
DescriptionINFOID:0000000006224441
MAIN switch does not turn ON
 ICC system display does not appear ev en when MAIN switch is pressed.
MAIN switch does not turn OFF When ICC system display is ON, display does not turn OFF even if MAIN switch is pressed.
NOTE:
When ICC system warning lamp illuminates, perform t he self-diagnosis of ICC system, and then repair or
replace the malfunctioning parts.
Diagnosis ProcedureINFOID:0000000006224442
1.MAIN SWITCH INSPECTION
1. Start the engine.
2. Check that “MAIN SW” and “CRUISE LAMP” operate no rmally in “DATA MONITOR” of “ICC/ADAS” with
CONSULT-III.
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 4.
2.CHECK COMBINATION METER
Check that “CRUISE IND” operates normally in “DATA MONITOR” of “METER/M&A”.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 4.
3.PERFORM SELF-DIAGNOSIS OF COMBINATION METER
1. Perform “Self Diagnostic Re sult” of “METER/M&A”.
2. Check if DTC is detected. Refer to MWI-43, "
DTC Index".
Is any DTC detected?
YES >> Repair or replace malfunctioning parts.
NO >> GO TO 4.
4.PERFORM SELF-DIAGNOSIS RESULTS OF ICC SYSTEM
1. Perform “All DTC Reading”.
2. Check if the “U1000” is detected in self-diagnosis results of “ICC/ADAS”.
Is
“U1000” detected?
YES >> GO TO 5.
NO >> GO TO 6.
5.CAN COMMUNICATIONS INSPECTION
Check the CAN communication and repair or replace malfunctioning parts. Refer to CCS-145, "
ADAS CON-
TROL UNIT : DTC Logic".
>> INSPECTION END
6.CHECK ICC STEERING SWITCH
Check the ICC steering switch. Refer to CCS-177, "
Exploded View".
>> INSPECTION END
Revision: 2010 May2011 QX56

CCS-162
< SYMPTOM DIAGNOSIS >[ICC]
ICC SYSTEM CANNOT BE SET
(MAIN SWITCH TURNS ON/OFF)
ICC SYSTEM CANNOT BE SET (MAIN SWITCH TURNS ON/OFF)
DescriptionINFOID:0000000006224443
The MAIN switch can be turned ON/OFF, but the ICC system cannot be set even if the SET/COAST switch is
pressed.
NOTE:
The system cannot be set in the following case.
 When the vehicle ahead is not detected bel ow the speed of 32 km/h (20 MPH).
 When the selector lever is not in the “D” position or manual mode.
 When the front wipers are operating at HI.
(If the vehicle is equipped with a rain sensing auto-wi per, the system may cancel when the wipers are set to
AUTO)
 When the brake pedal is depressed.
 When driving into a strong light (i.e., sunlight).
 When the VDC is turned OFF.
 When ABS or VDC (including the TCS) operates.
 When a wheel slips.
 When SNOW mode switch is turned ON.
 When ABS warning lamp is ON.
 When 4WD shift switch is not AUTO position.
Diagnosis ProcedureINFOID:0000000006224444
1.CHECK CAUSE OF AUTOMATIC CANCELLATION
Check if there is the cancellation cause in the “CAUSE OF AUTO-CANCEL” on “WORK SUPPORT” of “ICC/
ADAS” with CONSULT-III.
Is it displayed?
Not displayed>>GO TO 2.
“OPE SW VOLT CIRC”>>Refer to CCS-94, "
DTC Logic".
“VHCL SPD UNMATCH”>>Refer to CCS-87, "
DTC Logic".
“IGN LOW VOLT”>>Refer to CCS-85, "
ADAS CONTROL UNIT : DTC Logic".
“ECM CIRCUIT”>>Refer to CCS-103, "
DTC Logic".
“CAN COMM ERROR”>>Refer to CCS-145, "
ADAS CONTROL UNIT : DTC Logic".
“ICC SENSOR CAN COMM ERR”>>Refer to CCS-137, "
DTC Logic".
“ABS/TCS/VDC CIRC”>>Refer to CCS-89, "
DTC Logic".
“ECD CIRCUIT”>>Refer to CCS-115, "
DTC Logic".
2.PERFORM THE SELF-DIAGNOSIS
1. Perform “All DTC Reading”.
2. Check if any DTC is detected in “Self Diagnosti c Result” of “ICC/ADAS”” of “LASER”. Refer to CCS-50,
"DTC Index" (ICC/ADAS) or CCS-55, "DTC Index" (LASER).
Is any DTC detected?
YES >> GO TO 3.
NO >> GO TO 4.
3.REPAIR OR REPLACE MALFUNCTIONING PARTS
Repair or replace malfunctioning parts identified by the self-diagnosis result.
>> GO TO 6.
4.CHECK EACH SWITCH AND VEHICLE SPEED SIGNAL
1. Start the engine.
2. Check that the following items operate no rmally in “DATA MONITOR” of “ICC/ADAS”.
- “VHCL SPEED SE”
- “D RANGE SW”
- “SET/COAST SW”
- “BRAKE SW”
-“WIPER SW”
Revision: 2010 May2011 QX56