battery INFINITI QX56 2011 Factory Workshop Manual

BCS
DIAGNOSIS SYSTEM (BCM)BCS-29
< SYSTEM DESCRIPTION >
C
DE
F
G H
I
J
K L
B A
O P
N
WORK SUPPORT
BATTERY SAVER
BATTERY SAVER : CONSULT-III Function (BCM - BATTERY SAVER)INFOID:0000000006376482
WORK SUPPORT
*:Factory setting
DATA MONITOR
Test item Description
THEFT IND This test is able to check security indicator lamp operation.
Security indicator lamp is turned on when “ON” on CONSULT-III screen touched.
Service item Description
CONFIRM DONGLE ID It is possible to check that dongle unit is applied to the vehicle.
Service item Setting item Setting
ROOM LAMP TIMER SET MODE 1
*30 min.
Sets the interior room lamp battery saver timer operating
time.
MODE 2 60 min.
BATTERY SAVER SET On
*With the exterior lamp battery saver function
Off Without the exterior lamp battery saver function
Monitor item [Unit] Description
REQ SW-DR
[On/Off] The switch status input from door request switch (driver side)
REQ SW-AS
[On/Off] The switch status input from door request switch (passenger side)
REQ SW-RR
[On/Off] NOTE:
The item is indicated, but not monitored.
REQ SW-RL
[On/Off]
PUSH SW
[On/Off] The switch status input from push-button ignition switch
UNLK SEN-DR
[On/Off] Driver door unlock status input from unlock sensor
DOOR SW-DR
[On/Off] The switch status input from door switch (driver side)
DOOR SW-AS
[On/Off] The switch status input from door switch (passenger side)
DOOR SW-RR
[On/Off] The switch status input from rear door switch RH
DOOR SW- RL
[On/Off] The switch status input from rear door switch LH
DOOR SW- BK
[On/Off] The switch status input from back door switch
CDL LOCK SW
[On/Off] Lock switch status input from door lock and unlock switch
CDL UNLOCK SW
[On/Off] Unlock switch status input from door lock and unlock switch
KEY CYL LK-SW
[On/Off] Lock switch status received from door key cylinder switch
Revision: 2010 May2011 QX56

BCS-30
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
*: Each lamp switch is in ON position.
TRUNK
TRUNK : CONSULT-III Function (BCM - TRUNK)INFOID:0000000006376456
DATA MONITOR
THEFT ALM
THEFT ALM : CONSULT-III Function (BCM - THEFT)INFOID:0000000006376457
DATA MONITOR
KEY CYL UN-SW
[On/Off] Unlock switch status received from door key cylinder switch
TRNK/HAT MNTR
[On/Off] NOTE:
The item is indicated, but not monitored.
RKE-LOCK
[On/Off] Lock signal status received from remote keyless entry receiver
RKE-UNLOCK
[On/Off] Unlock signal status received from remote keyless entry receiver
Monitor item
[Unit] Description
Test item Operation Description
BATTERY SAVER Off Cuts the interior room lamp power supply to turn interior room lamps OFF.
On Outputs the interior room lamp power supply to turn interior room lamps ON.*
Monitor Item Contents
PUSH SW Indicates [On/Off] condition of push switch
UNLK SEN -DR Indicates [On/Off] condition of unlock sensor
VEH SPEED 1 Indicates [Km/h] condition of ve hicle speed signal from combination meter
TR/BD OPEN SW Indicates [On/Off] condition of back door opener switch
TRNK/HAT MNTR NOTE:
This item is displayed, but cannot be monitored
RKE-TR/BD NOTE:
This item is displayed, but cannot be monitored
Monitored Item Description
REQ SW -DR Indicates [ON/OFF] condition of door request switch (driver side).
REQ SW -AS Indicates [ON/OFF] condition of door request switch (passenger side).
REQ SW -RR NOTE:
This item is displayed, but cannot be monitored.
REQ SW -RL NOTE:
This item is displayed, but cannot be monitored.
REQ SW -BD/TR Indicates [ON/OFF] condition of back door request switch.
PUSH SW Indicates [ON/OFF] condition of push-button ignition switch
UNLK SEN -DR Indicates [ON/OFF] condition of driver door UNLOCK status.
DOOR SW-DR Indicates [ON/OFF] condition of front door switch (driver side).
DOOR SW-AS Indicates [ON/OFF] condition of front door switch (passenger side).
DOOR SW-RR Indicates [ON/OFF] condition of rear door switch RH.
Revision: 2010 May2011 QX56

BCS
BCM
BCS-41
< ECU DIAGNOSIS INFORMATION >
C
D E
F
G H
I
J
K L
B A
O P
N8
(V) Ground Power window
switch communica-
tion Input/
Output Ignition switch ON
9.0 - 10 V
9
(R) Ground Stop lamp switch 1 Input Stop lamp
switchOFF (Brake pedal is not
depressed)
0 V
ON (Brake pedal is de-
pressed) Battery voltage
11
(R) Ground
Light and rain sensor
serial link Input/
Output Ignition switch OFF 12 V
Ignition switch ON
8.0 - 9.0 V
14
(P/B) Ground Optical sensor Input Ignition switch
ONWhen bright outside of the
vehicle
Close to 5 V
When dark outside of the
vehicle Close to 0 V
16
(L/O) Ground Dimmer signal Output Ignition switch
ONEither of the following
conditions
 Lighting switch OFF
 The area around the ve-
hicle is bright (Shine a
light on the optical sen-
sor) 0 V
The area around the vehi-
cle is dark (Block the light
from the optical sensor) 12 V
17
(Y/G) Ground Sensor power sup-
ply
Output Ignition switch OFF, ACC 0 V
ON 5 V
18
(B/Y) Ground Receiver and sensor
ground Input Ignition switch ON 0 V
19
(BR) Ground Remote keyless en-
try receiver power
supply
Output Ignition switch OFF
Terminal No.
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
PKIA7023E
JPMIA0156GB
JMKIA3838GB
Revision: 2010 May2011 QX56

BCS-42
< ECU DIAGNOSIS INFORMATION >
BCM
20
(G/R) Ground Remote keyless en-
try receiver commu-
nication
InputWaiting
Signal receiving
21
(P) Ground NATS antenna amp. Input/
Output During waiting Ignition switch is pressed
while inserting the key into
the key slot. Just after pressing ignition
switch. Pointer of tester should move.
22
(W/B) Ground Remote keyless en-
try receiver RSSI
InputWaiting 0 V
Signal receiving
23
(GR/R) GroundSecurity indicator
lamp
OutputSecurity indica-
tor lamp ON 0 V
Blinking (Ignition switch
OFF)
11.0 - 12.0 V
OFF Battery voltage
24*
(SB) Ground Dongle link
Input/
Output Ignition switch OFF 5 V
25
(LG/R) Ground NATS antenna amp.
Input/
Output During waiting Ignition switch is pressed
while inserting the key into
the key slot. Just after pressing ignition
switch. Pointer of tester should
move.
29
(W) Ground Hazard switch Input Hazard switch OFF 12 V
ON 0 V
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −JMKIA3838GB
JMKIA3841GB
JMKIA3838GB
JPMIA0590GB
Revision: 2010 May2011 QX56

BCS
BCM
BCS-47
< ECU DIAGNOSIS INFORMATION >
C
D E
F
G H
I
J
K L
B A
O P
N
55
(G) Ground Rear door UNLOCK Output Rear door UNLOCK (Actuator is acti-
vated)
12 V
Other then UNLOCK (Ac-
tuator is not activated) 0 V
56
(W/R) Ground Interior room lamp
power supply OutputInterior room lamp battery saver is activated.
(Cuts the interior room
lamp power supply) 0 V
Interior room lamp battery saver is not acti-
vated.
(Outputs the interior room lamp power sup-
ply) 12 V
57
(LG) Ground Battery power sup-
ply
Input Ignition switch OFF Battery voltage
59
(G) Ground Passenger door UN-
LOCK
Output Passenger door UNLOCK (Actuator is acti-
vated)
12 V
Other then UNLOCK (Ac-
tuator is not activated) 0 V
60
(G) Ground Turn signal LH Output Ignition switch
ONTurn signal switch OFF 0 V
Turn signal switch LH
6.0 - 7.0 V
61
(G/Y) Ground Turn signal RH Output Ignition switch
ONTurn signal switch OFF 0 V
Turn signal switch RH
6.0 - 7.0 V
62
(R) Ground Step lamp Output Step lamp ON 0 V
OFF 12 V
63
(BR) Ground Interior room lamp
timer control
OutputInterior room
lamp OFF 12 V
ON 0 V
64
(GR/R) Ground Cranking request input
Ignition switch
ONEngine stopped (Selector
lever is in P position)
0 V
Engine stopped (Selector
lever is not in P position) 12 V
Engine running 12 V
65
(R) Ground All doors, fuel lid
LOCK
Output All doors, fuel lid LOCK (Actuator is activat-
ed)
12 V
Other then LOCK (Actua-
tor is not activated) 0 V
Terminal No.
(Wire color) Description
Condition
Va l u e
(Approx.)
Signal name Input/
Output
+ −
PKIC6370E
PKIC6370E
Revision: 2010 May2011 QX56

BCS-48
< ECU DIAGNOSIS INFORMATION >
BCM
66
(V) Ground Driver door, fuel lid
UNLOCK OutputDriver door, fuel
lid UNLOCK (Actuator is acti-
vated)
12 V
Other then UNLOCK (Ac-
tuator is not activated) 0 V
67
(B) Ground Ground Output Ignition switch ON 0 V
68
(Y) Ground P/W power supply
(IGN)
Output Ignition switch ON 12 V
69
(W) Ground
P/W power supply
(BAT) Output Ignition switch OFF 12 V
70
(Y) Ground Battery power sup-
ply Input Ignition switch OFF Battery voltage
72
(P) Ground Puddle lamp control Output Puddle lamp OFF 12 V
ON 0 V
73
(W) Ground ON indicator lamp Output Ignition switch OFF (LOCK indicator is
not illuminated)
Battery voltage
ON 0 V
74
(Y/B) Ground Trailer turn signal
RH control
OutputIgnition switch
ON Turn signal switch OFF Battery voltage
Turn signal switch RH
6.0 - 7.0 V
75
(LG/R) Ground
Driver door request
switch Input
Driver door re-
quest switch ON (Pressed) 0 V
OFF (Not pressed) 12 V
76
(P/L) Ground
Passenger door re-
quest switch Input
Passenger door
request switch ON (Pressed) 0 V
OFF (Not pressed) 12 V
77
(O/L) Ground Trailer turn signal LH
control
OutputIgnition switch
ON Turn signal switch OFF Battery voltage
Turn signal switch LH
6.0 - 7.0 V
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
PKIC6370E
PKIC6370E
Revision: 2010 May2011 QX56

BCS
BCM
BCS-53
< ECU DIAGNOSIS INFORMATION >
C
D E
F
G H
I
J
K L
B A
O P
N
90
(Y) Ground Push-button ignition
switch illumination OutputPush-button ig-
nition switch illu-
mination ON 12 V
OFF 0 V
91
(O) Ground LOCK indicator lamp Output LOCK indicator
lampOFF (Ignition switch OFF) Battery voltage
ON 0 V
92
(L) Ground Push-button ignition
switch illumination
ground Output Tail lamp OFF 0 V
ON
NOTE:
When the illumination brighten-
ing/dimming level is in the neutral position
6.0 - 7.0 V
93
(GR/R) GroundIntelligent Key warn-
ing buzzer
OutputIntelligent Key
warning buzzer Sounding 0 V
Not sounding 12 V
94
(Y/G) Ground Steering lock unit
communication Input/
Output Steering lock LOCK status 12 V
LOCK or UNLOCK
For 15 seconds after UN-
LOCK
12 V
15 seconds or later after
UNLOCK 0 V
95
(W) Ground
Steering lock unit
power supply Output Ignition switch OFF or ACC 12 V
ON 0 V
96
(BR) Ground ACC relay control Output Ignition switch OFF 0 V
ACC or ON 12 V
97
(R/W) Ground Starter relay control Output Ignition switch
ONWhen selector lever is in
P or N position
12 V
When selector lever is not
in P or N position 0 V
98
(O) Ground Ignition relay (IPDM
E/R) control
Output Ignition switch OFF or ACC 12 V
ON 0 V
99
(R) Ground Ignition relay-1 con-
trol
Output Ignition switch OFF or ACC 0 V
ON 12 V
100
(SB) Ground
Push-button ignition
switch (push switch) InputPush-button ig-
nition switch
(push switch) Pressed 0 V
Not pressed 12 V
101
(W/B) Ground Ignition power sup-
ply No. 2 Output Ignition switch OFF or ACC 0 V
ON 12 V
Terminal No.
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
JPMIA1554GB
JMKIA0066GB
Revision: 2010 May2011 QX56

BCS-54
< ECU DIAGNOSIS INFORMATION >
BCM
*: For Canada
Fail-safeINFOID:0000000006274820
FAIL-SAFE CONTROL BY DTC
BCM performs fail-safe control when any DTC are detected.
102
(BR) Ground P/N position Input Selector lever P or N position 12 V
Except P and N positions 0 V
104
(R/B) Ground A/T shift selector
(detention switch)
power supply Output Ignition switch ON 12 V
105
(O/L) Ground Stop lamp switch 2 Input Ignition switch OFF Battery voltage
106
(Y/G) Ground
Blower fan motor re-
lay control Output Ignition switch OFF or ACC 0 V
ON 12 V
107 (L) Ground
Steering lock condi-
tion No. 1 Input Steering lock LOCK status 0 V
UNLOCK status 12 V
108 (P) Ground
Steering lock condi-
tion No. 2 Input Steering lock LOCK status 12 V
UNLOCK status 0 V
109
(L/W) Ground ACC indicator lamp Output Ignition switch OFF (LOCK indicator is
not illuminated)
Battery voltage
ACC 0 V
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
Display contents of CONSULT Fail-safe Cancellation
B2013: ID DISCORD BCM-S/ L Inhibit engine cranking When communication between BCM and steering lock unit are commu-
nicated normally.
B2014: CHAIN OF S/L-BCM Inhibit engine cranking When communication between BCM and steering lock unit are commu-
nicated normally.
B2192: ID DISCORD BCM-ECM Inhibit engine cranking Erase DTC
B2193: CHAIN OF BCM-ECM Inhibit engine cranking Erase DTC
B2195: ANTI-SCANNING Inhibit engine cranking Ignition switch ON → OFF
B2198: NATS ANTENNA AMP Inhibit engine cranking Erase DTC
B2557: VEHICLE SPEED In hibit steering lockWhen the following CAN signal status (vehicle speed signal) becomes
consistent
 Vehicle speed signal (ABS)
 Vehicle speed signal (Meter)
B2601: SHIFT POSITION Inhibit steering lock 500 ms after the following signal reception status becomes consistent
 Selector lever P position switch signal
 P range signal (CAN)
B2602: SHIFT POSITION Inhibit steering lock 5 seconds after the following BCM recognition conditions are fulfilled
 Ignition switch is in the ON position
 Selector lever P position switch signal: Except P position (battery volt-
age)
 Vehicle speed: 4 km/h (2.5 MPH) or more
Revision: 2010 May2011 QX56

BCS-56
< ECU DIAGNOSIS INFORMATION >
BCM
FAIL-SAFE CONTROL BY RAIN SENSOR MALFUNCTION
BCM detects the light and rain sensor serial link error and the rain sensor malfunction.
BCM controls the following fail-safe when rain sensor has a malfunction.
 Front wiper switch AUTO and sensing rain drop: The condition just before the activation of fail-safe is main-
tained until the front wiper switch is turned OFF.
 Front wiper switch AUTO and not sensing rain drop: Front wiper is LO operation until the front wiper switch is
turned off.
REAR WIPER MOTOR PROTECTION
BCM detects the rear wiper stopping position acco rding to the rear wiper stop position signal.
When the rear wiper stop position signal does not c hange for more than 5 seconds while driving the rear
wiper, BCM stops power supply to protect the rear wiper motor.
Condition of cancellation
1. More than 1 minute is passed after the rear wiper stop.
2. Turn rear wiper switch OFF.
3. Operate the rear wiper swit ch or rear washer switch.
FAIL-SAFE CONTROL OF COMBINATION SWITCH READING FUNCTION CAUSED BY LOW
POWER SUPPLY VOLTAGE
If voltage of battery power supply lower, BCM maintain s combination switch reading to the status when input
voltage is less than approximately 9 V.
NOTE:
When voltage of battery power supply is approximately 9 V or more, combination switch reading function
returns to normal operation.
DTC Inspection Priority ChartINFOID:0000000006274821
If some DTCs are displayed at the same time, perfo rm inspections one by one based on the following priority
chart.
B26F3: START CONT RLY ON Inhibit engine cranking When the following conditions are fulfilled
 Starter control relay signal (CAN: Transmitted from BCM): OFF
 Starter control relay signal (CAN: Transmitted from IPDM E/R): OFF
B26F4: START CONT RLY OFF Inhibit engine cranking When the following conditions are fulfilled
 Starter control relay signal (CAN: Transmitted from BCM): ON
 Starter control relay signal (CAN: Transmitted from IPDM E/R): ON
B26F7: BCM Inhibit engine cranking
by Intelligent Key sys-
temWhen room antenna and luggage room antenna functions normally
U0415: VEHICLE SPEED Inhibit steering lock When vehicle speed signal (Meter) (CAN) is received normally
Display contents of CONSULT Fail-safe Cancellation
Priority DTC
1 B2562: LOW VOLTAGE
2  U1000: CAN COMM
 U1010: CONTROL UNIT (CAN)
3  B2192: ID DISCORD BCM-ECM
 B2193: CHAIN OF BCM-ECM
 B2195: ANTI-SCANNING
 B2198: NATS ANTENNA AMP
Revision: 2010 May2011 QX56

BCS
POWER SUPPLY AND GROUND CIRCUITBCS-75
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
J
K L
B A
O P
N
POWER SUPPLY AND GROUND CIRCUIT
Diagnosis ProcedureINFOID:0000000006274841
1.CHECK FUSE AND FUSIBLE LINK
Check that the following fuse and fusible link are not blown.
Is the fuse fusing?
YES >> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is blown.
NO >> GO TO 2.
2.CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connectors.
3. Check voltage between BCM harness connector and ground.
Is the measurement value normal?
YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
Does continuity exist?
YES >> INSPECTION END
NO >> Repair harness or connector.
Signal name Fuse and fusible link No.
Battery power supply K
10
Te r m i n a l s
Vo l ta g e
(Approx.)
(+) (
−)
BCM
Ground
Connector Terminal
M70 70
Battery voltage
57
BCM
GroundContinuity
Connector Terminal
M70 67 Existed
Revision: 2010 May2011 QX56