ISUZU AXIOM 2002 Service Repair Manual

WIPER/WASHER SYSTEM8B±13
Rear Wiper Blade Rubber
Removal
1. Remove the wiper blade from the wiper arm.
2. Press and hold the wiper rubber under the wiper blade
hook (1).
3. Pull the wiper rubber out from wiper blade.
CAUTION: W h e n t h e w i p e r blade has been
removed, wrap the tip of the wiper arm with cloth, to
avoid damaging the glass.
885R200004
Installation
1. Install the wiper blade rubber.

Matching the grove of the wiper rubber (3) and the
guide (2) of the wiper blade (1), insert the wiper
rubber to the wiper blade.
885R200009

Check that the wiper rubber is set between the right
hook and left hook of the wiper blade.
885R200008

8B±14WIPER/WASHER SYSTEM
Main Data and Specifications
Torque Specifications
ApplicationN´mLb FtLb In
Windshield Wiper Motor Shaft Nut14Ð122
Windshield Wiper Arm Nuts2317Ð
Rear Wiper Motor Shaft Nut10Ð87
Rear Wiper Arm Nut9Ð78

ENTERTAINMENT8C±1
AXIOM
BODY AND ACCESSORIES
ENTERTAINMENT
CONTENTS
Service Precaution 8C±1. . . . . . . . . . . . . . . . . . . . . .
Cigarette Lighter 8C±2. . . . . . . . . . . . . . . . . . . . . . . .
General Description 8C±2. . . . . . . . . . . . . . . . . . . . .
Removal 8C±2. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8C±2. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rod Type Antenna 8C±3. . . . . . . . . . . . . . . . . . . . . .
Removal 8C±3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8C±3. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessory Socket 8C±4. . . . . . . . . . . . . . . . . . . . . . .
Front Accessory Socket 8C±4. . . . . . . . . . . . . . . .
Removal 8C±4. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8C±4. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Accessory Socket 8C±4. . . . . . . . . . . . . . . .
Removal 8C±4. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8C±4. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio 8C±5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 8C±5. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8C±5. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speaker 8C±6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Speaker 8C±6. . . . . . . . . . . . . . . . . . . . . . . . .
Removal 8C±6. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8C±6. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Tweeter Assembly 8C±6. . . . . . . . . . . . . . . .
Removal 8C±6. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8C±6. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Door Speaker 8C±6. . . . . . . . . . . . . . . . . . . .
Removal 8C±6. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8C±7. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Tweeter Assembly 8C±7. . . . . . . . . . . . . . . .
Removal 8C±7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation 8C±7. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Horn 8C±8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 8C±8. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8C±8. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display (MID) 8C±8. . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 8C±8. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8C±8. . . . . . . . . . . . . . . . . . . . . . . . . . . .
MID Control Unit 8C±9. . . . . . . . . . . . . . . . . . . . . . . .
Removal 8C±9. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8C±9. . . . . . . . . . . . . . . . . . . . . . . . . . . .
GPS Control Unit 8C±10. . . . . . . . . . . . . . . . . . . . . . . .
Removal 8C±10. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8C±10. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Self-Diagnosis 8C±11. . . . . . . . . . . . . . . . . . . . . . . . . .
Self-Diagnosis Flow Chart±1 8C±11. . . . . . . . . . . .
Self-Diagnosis Flow Chart±2 (Audio) 8C±12. . . . .
Self-Diagnosis Flow Chart±3 (Display) 8C±13. . .
Self-Diagnosis Flow Chart±4 (MID) 8C±14. . . . . .
Audio Self-Diagnosis 8C±15. . . . . . . . . . . . . . . . . . .
Display Self-Diagnosis 8C±16. . . . . . . . . . . . . . . . .
MID Self-Diagnosis 8C±17. . . . . . . . . . . . . . . . . . . .
Symptom Diagnosis 8C±18. . . . . . . . . . . . . . . . . . . . .
MID Not Appears 8C±18. . . . . . . . . . . . . . . . . . . . . .
No COMPASS, CLOCK, FUEL
CONSUMPTION, or SERVICE Display 8C±19. .
No COMPASS Display 8C±20. . . . . . . . . . . . . . . . .
No SERVICE Display 8C±20. . . . . . . . . . . . . . . . . .
Other Trouble Symptom 8C±21. . . . . . . . . . . . . . . .
MID Circuit 8C±22. . . . . . . . . . . . . . . . . . . . . . . . . . .
Harness Connector Faces 8C±23. . . . . . . . . . . . . .
Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING, REFER TO
THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN POSSIBLE
AIR BAG DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.
CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, or other
corrosion inhibitors) on threaded fasteners or
fasteners joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fasteners.
When you install fasteners, use the correct
tightening sequence and specifications. Following
these instructions can help you avoid damage to
parts and systems.

8C±2ENTERTAINMENT
Cigarette Lighter
General Description
When the cigarette lighter is pushed in with the starter
switch at either ªACCº or ªONº position, a circuit is formed
in the cigarette lighter case to heat the lighter coil.
The cigarette lighter springs back to its original position
after the lighter coil is heated.
Removal
1. Disconnect the battery ground cable.
2. Remove the center cluster assembly (1).

Refer to
Instrument Panel Assembly in Body
Structure section.
3. Remove the cigarette lighter assembly (2).

Disconnect the connectors.

Remove the socket (3) and nut (4).
826R200012
Installation
To install, follow the removal steps in the reverse order,
noting the following point:
1. When installing the bezel, align the projected portion
of the socket with the notch of the bezel.

ENTERTAINMENT8C±3
Rod Type Antenna
Removal
1. Disconnect the battery ground cable.
2. Turn the antenna rod (1) counterclockwise to remove
it.
3. Remove three screws and nine clips to remove the
fender inner liner (5).
4. Disconnect the feeder cable connector (4) at the
inside of the vehicle.
5. Turning the lock nut (2) counterclockwise removes it
together with the base mold (3).
6. Pull down and remove the housing (7) from the panel.
7. Pull and remove the cable with the grommet (6).
890R200040
Installation
To install, follow the removal steps in the reverse order.

8C±4ENTERTAINMENT
Accessory Socket
Front Accessory Socket
Removal
1. Disconnect the battery ground cable.
2. Remove the front console assembly (2).

Refer to
Instrument Panel Assembly in Body
Structure section.
3. Remove the front accessory socket (1).

Disconnect the connectors.

Remove the holdernut (3).
826R200013
Installation
To install, follow the removal steps in the reverse order.
Rear Accessory Socket
Removal
1. Disconnect the battery ground cable.
2. Remove the quarter trim lower cover.
3. Remove the rear accessory socket (1).

Disconnect the connectors (3).

Pull out the rear accessory socket from the socket
cover (2).
826R200014
Installation
To install, follow the removal steps in the reverse order.

ENTERTAINMENT8C±5
Audio
Removal
1. Disconnect the battery ground cable.
2. Remove the center cluster assembly (1).

Refer to
Instrument Panel Assembly in Body
Structure section.
890R200032
3. Remove the audio (2).

Remove the two fixing screws (3).

Disconnect the connector and the antenna cable.
890R200033
Installation
To install, follow the removal steps in the reverse order.

8C±6ENTERTAINMENT
Speaker
Front Speaker
Removal
1. Disconnect the battery ground cable.
2. Remove the front door trim pad.

Refer to
Front Door in Body Structure section.
3. Remove the front speaker (2).

Remove the three screws and the speaker spacer
(1).

Disconnect the connector (3).
890R200028
Installation
To install, follow the removal steps in the reverse order.
Front Tweeter Assembly
Removal
1. Disconnect the battery ground cable.
2. Remove the front door trim pad (2).

Refer to
Front Door in Body Structure section.
3. Remove the tweeter (1).

Disconnect the connector.
890R200030
Installation
To install, follow the removal steps in the reverse order.
Rear Door Speaker
Removal
1. Disconnect the battery ground cable.
2. Remove the rear door trim pad.

Refer to
Rear Door in Body Structure section.
3. Remove the rear speaker (2).

Remove the three screws and the speaker spacer
(1).

Disconnect the connector (3).
890R200028

ENTERTAINMENT8C±7
Installation
To install, follow the removal steps in the reverse order.
Rear Tweeter Assembly
Removal
1. Disconnect the battery ground cable.
2. Remove the rear door trim pad (2).

Refer to
Rear Door in Body Structure section.
3. Remove the tweeter (1).

Disconnect the connector.
890R200031
Installation
To install, follow the removal steps in the reverse order.

8C±8ENTERTAINMENT
Horn
Removal
1. Disconnect the battery ground cable.
2. Remove the horn.

Disconnect the connector.

Remove the horn mounting bolt.
NOTE: High (1), Low (2)
828R200003
Installation
To install, follow the removal steps in the reverse order.
Display (MID)
Removal
1. Disconnect the battery ground cable.
2. Remove the cluster upper cover.

Disconnect the sun sensor connector and the GPS
control unit connector.
3. Remove the center cluster.

Refer to
Instrument Panel Assembly in Body
Structure.
4. Remove the Display (1).

Remove the screws (2).

Disconnect the Display connector and MID control
unit connector.
890R200036
Installation
To install, follow the removal steps in the reverse order.