lighting system ISUZU AXIOM 2002 Service User Guide

LIGHTING SYSTEM8A±3
Headlight Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the headlight bulb.

Disconnect the connector (2).

Remove the socket (1) by turning it
counterclockwise.
CAUTION: Do not touch the headlight bulb with
your fingers. The oil on your fingers will leave a
residue which will shorten the life of the halogen
bulb. In order to prevent this problem, clean the bulb
lens before installing the headlight bulb.
801R200021
Installation
To install, follow the removal steps in the reverse order.
noting the following point:
1. Make sure to set the retaining ring and the bulb cover.
If the set is incomplete, there is a possibility that the
water comes in the light.

8A±4LIGHTING SYSTEM
Headlight Assembly
Removal
1. Disconnect the battery ground cable.
2. Remove the front combination light (2).

Remove the screw.

Disconnect the connector.
3. Remove the headlight assembly (1).

Disconnect the connector.

Remove four screws.
801R200022
Installation
To install, follow the removal steps in the reverse order.
noting the following point:
1. After installing the headlight, be sure to adjust the
headlight aim.
Headlight Adjustment
Preparation
Place the vehicle with 1 person in driver seat on a level
surface and check to see if the inflation pressure of the
tires is correct, the lenses are clean, the battery is
sufficiently charged, and adjust to place vehicle by using
the screen.1. Set a vertical screen on a level surface.
2. Toward the screen (1) from the bulb center mark of
the headlight, extend parallel lines to the floor. Mark
point (A) and (B) on the screen at the intersection of
parallel line and the screen.
3. Draw vertical lines through point (A) and (B) on the
screen.
801R200019
4. Keep the vehicle (2) 3m (9.8 ft) apart from the screen
(1).
5. Draw a horizontal line through point (A) and (B) on the
screen (1).
801R200009

LIGHTING SYSTEM8A±5
6. Turn the headlight low beam on.
7. Adjust the CUTLINE 30 mm (1.18 in) below the
horizontal line (H).
801R200011
Vertical Adjustment
Use a screwdriver for vertical adjustment.
801R200012

8A±6LIGHTING SYSTEM
Side Marker Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the front combination light (1).

Remove the screw.
3. Remove the bulb (2).

Remove the side marker light socket (3) by turning it
counterclockwise.

Remove the bulb by turning it counterclockwise
while pushing it at the same time.
801R200013
Installation
To install, follow the removal steps in the reverse order.

LIGHTING SYSTEM8A±7
Taillight Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the rear combination light assembly (1).

Remove two screws.

Pull out the rear combination light assembly
outside.
803R200011
3. Remove the bulb (1).

Remove the taillight socket by turning it
counterclockwise.

Remove the bulb by turning it counterclockwise
while pushing it at the same time.
803R200002
Installation
To install, follow the removal steps in the reverse order.

8A±8LIGHTING SYSTEM
License Plate Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the license plate light garnish.

Remove the three screws.
3. Remove the lens cover (3).

Remove two screws.
4. Remove the license plate light socket by turning it
counterclockwise.
5. Remove the bulb (2).

Pull out the bulb from the socket (1).
803R200003
Installation
To install, follow the removal steps in the reverse order.
Stoplight Bulb
Removal and Installation
Refer to Taillight Bulb in this section.

LIGHTING SYSTEM8A±9
High Mounted Stoplight Assembly
Removal
1. Disconnect the battery ground cable.
2. Remove the high mounted stoplight assembly (1).

Remove the cover (2).

Remove two screws.

Disconnect the connector.
803R200004
Installation
To install, follow the removal steps in the reverse order.
High Mounted Stoplight Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the cover.
3. Remove the high mounted stoplight assembly (1).

Remove two screw.
4. Remove the bulb (2).

Remove the socket by turning it counterclockwise.
803R200005
Installation
To install, follow the removal steps in the reverse order.

8A±10LIGHTING SYSTEM
Backup Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the rear combination light assembly.

Refer to
Taillight Bulb in this section.
3. Remove the bulb (1).

Remove the backup light socket by turning it
counterclockwise.

Pull out the bulb from the socket.
803R200007
Installation
To install, follow the removal steps in the reverse order.
Front Turn Signal Light Bulb
Removal and Installation
Refer to Side Marker Light Bulb in this section.

LIGHTING SYSTEM8A±11
Rear Turn Signal Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the rear combination light assembly.

Refer to
Taillight Bulb in this section.
3. Remove the bulb (1).

Remove the rear turn signal light socket by turning it
counterclockwise.

Remove the bulb by turning it counterclockwise
while pushing it at the same time.
803R200006
Installation
To install, follow the removal steps in the reverse order.
Dome Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the lens (2).
3. Remove the bulb (1).

Pull out the bulb.
825RW075
Installation
To install, follow the removal steps in the reverse order.

8A±12LIGHTING SYSTEM
Map Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the lens (2).
3. Remove the bulb (1).

Pull out the bulb.
805R200002
Installation
To install, follow the removal steps in the reverse order.
Courtesy Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the lens (2).
3. Remove the bulb (1).

Pull out the bulb.
825RW076
Installation
To install, follow the removal steps in the reverse order.