lock ISUZU TF SERIES 2004 Workshop Manual

ELECTRICAL-BODY AND CHASSIS 8A-173
REMOVAL AND INSTALLATION


REAR COMBINATION LIGHT
Stoplight
Removal
1. Open the rear gate.
2. Remove the screws of rear combination light.
3. Remove the rear combination light assembly.


4. Turn the bulb 2 counterclockwise to remove it.



Installation
Follow the removal procedure in the reverse order to install the
rear combination light.
Pay close attention to the important points mentioned in the
following paragraphs.



Bulb
Be absolutely sure that each bulb is correctly installed.
This will prevent a poor contact and an open circuit.

HIGH MOUNTED STOPLIGHT
Remove the bulb socket
1. Remove the high mounted stoplight ASM.

Remove the screws.

Disconnect the connector.

2. Remove the bulb socket.

Turn the bulb
1 counterclockwise to remove it.

8A-174 ELECTRICAL-BODY AND CHASSIS

Installation
Follow the removal procedure in the reverse order to install the
rear combination light.
Pay close attention to the important points mentioned in the
following paragraphs.



Bulb
Be absolutely sure that each bulb is correctly installed.
This will prevent a poor contact and an open circuit.

SIDE TURN LIGHT
Removal
1. Remove the lens 1.

Pull the light/bulb toward you while pushing the ligh
t
housing in the rear direction of the vehicle to release its
lock.

Remove the socket by turning it counterclockwise.
2. Pull the bulb
2 to remove it.


Installation
Follow the removal procedure in the reverse order to install the
side turn light.
Pay close attention to the important points mentioned in the
following paragraphs.



Bulb
Be absolutely sure that the side turn light bulb is correctly
installed.
This will prevent a poor contact and an open circuit.
















REAR COMBINATION LIGHT
Turn Signal Light
Removal
1. Open the rear gate.
2. Remove the screws.
3. Remove the rear combination light assembly.

4. Turn the bulb 1 counterclockwise to remove it.

ELECTRICAL-BODY AND CHASSIS 8A-177

REAR COMBINATION LIGHT
Back Up Light
Removal
1. Open the rear gate.
2. Remove the screws.
3. Remove the rear combination light assembly.

4. Turn the bulb
3 counterclockwise to remove it.



Installation
Follow the removal procedure in the reverse order to install the
rear combination light.
Pay close attention to the important points mentioned in the
following paragraphs.



Bulbs
Be absolutely sure that each bulb is correctly installed.
This will prevent a poor contact and an open circuit.

This illustration is based on RHD model

HAZARD WARNING FLASHER SWITCH
Removal
1. Disconnect the battery ground cable.
2. Instrument Panel Cluster Assembly

Refer to Section 10 “BODY” for instrument panel cluste
r
assembly removal steps.
3. Hazard Warning Switch

Disconnect the switch connector.

To remove the switch, push the lock from the back side
of the cluster assembly.


Installation
To install, follow the removal procedure in the reverse order.



Connector
Be absolutely sure that the hazard warning flasher switch
connector is securely connected.
This will prevent a poor contact and an open circuit.

ELECTRICAL-BODY AND CHASSIS 8A-179

HORN SWITCH
Removal
1. Disconnect the battery ground cable.
2. Disable the SRS (Refer to “Disabling the SRS”in this
section).
3. Check the both side hole of the steering cover.


4. Check the position of the pins in a hole. Push the pin in the
direction of an arrow.


5. Push the four pins at 56 mm bar.

6. Cancel the lock four pins.
7. Disconnect the SRS air bag connector and horn lead
connector located behind the air bag assembly and remove
the air bag assembly.

Installation
1. Connect the SRS bag connector and horn lead connector.
2.
Align the each snap stud of driver air bag to the hole of
steering wheel.

ELECTRICAL-BODY AND CHASSIS 8A-193

DOOR SWITCH
Removal
1. Disconnect the battery ground cable.
2. Loosen the screw

1.
3. Remove the door switch.
4. Disconnect the door switch connector
3.





Installation
Follow the removal procedure in the reverse order to install the
spot light.
Pay close attention to the important points mentioned in the
following paragraphs.



Connector
Be absolutely sure that the door switch connector is securely
connected.
This will prevent a poor contact and an open circuit.


SPOT LIGHT (MAP Light)
Removal
1. Grasp the spot light housing
1 with both hands.
Pull the housing straight down.
This will release the clip.
2. Disconnect the connector

2.
3. Turn socket
3 counterclockwise to remove it.

ELECTRICAL-BODY AND CHASSIS 8A-263



WARNING LIGHT BULB, INDICATOR
LIGHT BULB AND ILLUMINATION LIGHT
BULB
Removal
Turn the bulb socket counterclockwise and pull the bulb out.



Installation
To Install, follow the removal steps in the reverse order.











FUEL TANK UNIT
Removal
Dismount the fuel tank first, then remove the fuel tank unit.
1. Remove the rear inner liner -LH

Remove the clip
2. Remove the filler neck.

Remove the screw
3. Remove the ground with cable.
4. Remove the fuel tank band.

T/M jack unit on the vehicle.

Disconnect fuel line quick connectors.
5. Remove the fuel tank unit from the fuel tank.

ELECTRICAL-BODY AND CHASSIS 8A-275







Connector No. B-23
Terminal Connector place SOUTH
AFRICA SAUDI
ARABIA ISRAEL EC UK OTHER
1
ABS CONT. (BRAKE)
2
CHECK TRANS
3
A/T-P
4
A/T-R
5
A/T-2
6
A/T-L
7








8








9
BRAKE
10
CHARGE
11
TURN (R)
12
A/T-N
13
A/T-D
14
A/T-3
15
DIFF. LOCK





16
A/T OIL TEMP


17
ILL (-)
18
ILL (+)



RTW48AXF005901

ELECTRICAL-BODY AND CHASSIS 8A-293
POWER DOOR LOCK
PARTS LOCATION (RHD)








RTW48AXF019201 & RTW48AXF019301

ELECTRICAL-BODY AND CHASSIS 8A-297

CIRCUIT DIAGRAM WITH SUPER LOCK (RHD ONLY) Sheet 1/3




RTW48AXF025401

8A-298 ELECTRICAL-BODY AND CHASSIS

CIRCUIT DIAGRAM WITH SUPER LOCK (RHD ONLY) Sheet 2/3




RTW48AXF024801