engine remove ISUZU TF SERIES 2004 Workshop Manual

6A-64 ENGINE MECHANICAL (6VE1 3.5L)
Camshaft
Camshaft and Associated Parts







014RW040
Legend
(1) Camshaft Bracket Fixing Bolt
(2) Camshaft Bracket
(3) Camshaft Assembly Intake
(4) Camshaft Assembly Exhaust
(5) Pulley Fixing Bolt

(6) Camshaft Drive Gear Pulley
(7) Retainer Fixing Bolt
(8) Retainer
(9) Camshaft Drive Gear
(10) Oil Seal

Disassembly
1. Remove fixing bolt (5) for camshaft drive gear
pulley using 5
8840
2447&
ndash;0 universal
holder.

ENGINE MECHANICAL (6VE1 3.5L) 6A-65



014RW060
2. Remove twenty fixing bolts from inlet and exhaust
camshaft bracket on one side bank, then camshaft
brackets (2).








014RW027
3. Remove camshaft assembly (3), (4).
4. Remove three fixing bolts (7) from camshaft drive
gear retainer (8), then camshaft drive gea
r
assembly.

Inspection and Repair
1. Use a micrometer to measure the cam lobe height
and uneven wear. Replace the camshaft if eithe
r
the lobe height or the uneven wear exceeds the
specified limit.
Lobe height: 44.709 mm (1.7602 in)
Uneven wear: 0.05 mm (0.0020 in)

014RW043
2. Use a micrometer to measure the diameter and
the uneven wear of the camshaft journals.
Replace the camshaft if the diameter or the
uneven wear exceeds the specified limit.
Journal Diameter
Standard: 25.972 mm




25.993 mm (1.0225
in




1.0233 in)
Limit: 25.8 mm (1.0157 in)
Uneven wear: 0.05 mm (0.0020 in)





014RS023

ENGINE MECHANICAL (6VE1 3.5L) 6A-71
Crankshaft
Crankshaft and Associated Parts



013RW009
Legend
(1) Cylinder Head Assembly
(2) Crankcase with Oil Pan
(3) Oil Pipe and O-Ring
(4) Oil Strainer and O-Ring
(5) Oil Pump Assembly
(6) Cylinder Block Side Bolts
(7) Oil Gallery
(8) Piston and Connecting Rod Assembly
(9) Flywheel
(10) Rear Oil Seal Retainer and Oil Seal
(11) Main Bearing Cap
(12) Crankshaft
(13) Main Bearing Cap Fixing Bolts
(14) Oil Gallery Fixing Bolts

Disassembly
1. Remove cylinder head assembly (1). Refer to
“Head" in this manual. 2. Remove crankcase with oil pan (2). Refer to “Oil
Pan and Crankcase" in this manual.
CAUTION: Take care not to damage or deform the
sealing flange surface of crankcase.

6A-72 ENGINE MECHANICAL (6VE1 3.5L)
3. Remove oil pipe and O-ring (3).
4. Remove oil strainer and O-ring (4).
5. Remove oil pump assembly (5).
6. Remove crankcase side bolts (6).
7. Remove oil gallery (7).
8. Remove piston and connecting rod assembly (8).
Refer to “Piston, Piston Ring and Connecting Rod"
in this manual.
9. Remove flywheel (9).
10. Remove rear oil seal retainer (10).
11. Remove main bearing cap (11).
12. Remove crankshaft (12).
Inspection and Repair
1. Crankshaft
Set the dial indicator as shown in the illustration
and measure the crankshaft thrust clearance. I
f
the thrust clearance exceeds the specified limit,
replace the thrust bearings as a set.
Thrust Clearance
Standard : 0.06 mm




0.24 mm
(0.0024 in




0.0094 in)
Limit : 0.30 mm (0.0118 in)




015RS003

Main Bearing Clearance
1. Remove the bearing caps and measure the oil
clearance.
2. Remove the main bearing cap fixing bolts in the
sequence shown in the illustration.

Arrange the removed main bearing caps in the
cylinder number order.
Remove the main bearings.



015RS004
3. Remove the crankshaft. Remove the main
bearings.
4. Clean the upper and lower bearings as well as the
crankshaft main journal.
5. Check the bearings for damage or excessive wear.
The bearings must be replaced as a set if damage
or excessive wear is discovered during inspection.
6. Set the upper bearings and the thrust washers to
their original positions.
Carefully install the crankshaft.
7. Set the lower bearings to the bearing cap original
position.
8.
Apply plastigage to the crankshaft journal unit as
shown in the illustration.
NOTE: Do not set the plastigage on the oil hole.


015RS005
9. Install main bearing caps, oil gallery and crank
case bolts in the order shown, and tighten each
bolt to the specified torque.
NOTE: Do not apply engine oil to the crank case side

ENGINE MECHANICAL (6VE1 3.5L) 6A-73
bolts.
Main bearing cap bolts.
Torque: 39 N
 m (4.0 Kg
 m/29 lb ft)
Oil gallery fixing bolts.
Torque:
1st step: 29 N
 m (3.0 Kg
 m/21 lb ft)
2nd step 55
  
  65
 
Crank case side bolts
Torque : 39 N
 m (4.0 Kg
 m/29 lb ft)
NOTE: Do not allow the crankshaft to rotate.




015RS006
10. Remove the main bearing caps in the sequence
shown in the illustration.




015RS004
11. Measure the plastigage width and determine the
oil clearance. If the oil clearance exceeds the
specified limit, replace the main bearings as a se
t
and/or replace the crankshaft.
Standard : 0.019 mm




0.043 mm
(0.0007 in




0.0017 in)
Limit : 0.08 mm (0.0031 in)





015RS008
12. Clean the plastigage from the bearings and the
crankshaft.
Remove the crankshaft and the bearings.
Crankshaft (12) Inspection
Inspect the surface of the crankshaft journal and crank
pins for excessive wear and damage. Inspect the oil
seal fitting surfaces for excessive wear and damage.
Inspect the oil ports for obstructions.
Inspection and Repair
1. Carefully set the crankshaft on the V
blocks.
Slowly rotate the crankshaft and measure the
runout. If the crankshaft runout exceeds the
specified limit, the crankshaft must be replaced.
Runout : 0.04 mm (0.0016 in)






015RS007

ENGINE MECHANICAL (6VE1 3.5L) 6A-75

Grade
Mark
Cylinder Block
Journal
Crank Shaft Journal
Diameter
Grade
Mark
Color Code
Oil Clearance
(Reference)
1 68.994-69.000
(2.7163-2.7165) 63.918-63.925
(2.5165-2.5167) 2 Blue 0.024-0.043
(0.0009-0.0017)
63.926-63.933
(2.5168-2.5170) 1 Brown 0.022-0.041
(0.0009-0.0016)
2 68.987-68.993
(2.7160-2.7163) 63.918-63.925
(2.5165-2.5167) 2 0.023-0.042
(0.0009-0.0016)
63.926-63.933
(2.5168-2.5170) 1 Green 0.021-0.040
(0.0008-0.0016)
3 68.980-68.986
(2.7157-2.7160) 63.918-63.925
(2.5165-2.5167) 2 0.022-0.041
(0.0009-0.0016)
63.926-63.933
(2.5168-2.5170) 1 Yellow 0.020-0.039
(0.0008-0.0015)

Reassembly
1. Crankshaft (12)
 Install the main bearings to the cylinder block
and the main bearing caps.
 Be sure that they are positioned correctly.

Apply new engine oil to the upper and lower
main bearing faces.
NOTE: Do not apply engine oil to the main bearing back
faces.






015RS012
Legend
(1) Numver 1 and 4 main bearing upper and lower
(2) Numver 2 and 3 main bearing upper
(3) Numver 2 and 3 main bearing lower

 Carefully mount the crankshaft.
 Apply engine oil to the thrust washer.

Assemble the thrust washer to the No.3 bearing
journal. The oil grooves must face the
crankshaft.




015RS013
2. Rear oil seal (10)
 Remove the oil from the cylinder block and the
retainer mounting surface.
 Apply sealant (TB
1207B or equivalent) to the
retainer mounting surface, following the pattern
shown in the illustration.
The retainer must be installed within 5 minutes
after sealant application before the sealan
t
hardens.

6A-76 ENGINE MECHANICAL (6VE1 3.5L)




015RW002
Legend
(1) Around Bolt Holes
(2) Around Dowel Pin

 Apply engine oil to the oil seal lip.

Align the cylinder block dowel pin holes with the
rear retainer dowel pins.
 Tighten the rear retainer fixing bolts. New bolts
should be used when installing rear retainer.
Torque: 18 N
 m (1.8 Kg
 m/13 lb ft)
NOTE: Be very careful not to disengage the oil seal
garter spring during installation of the rear retainer.
If the seal was removed from retainer fo
r
replacement, apply engine oil to the oil seal lip
and install the oil seal using 5
8840
2286
0 oil
seal installer.




015RW001





015RS017
3. Flywheel (9)
1. Thoroughly clean and remove the oil from the
threads of crankshaft.
2. Remove the oil from the crankshaft and
flywheel mounting faces.
3. Mount the flywheel on the crankshaft and then
install the washer.
4. Hold the crankshaft to prevent from rotating
then install the bolts in the order shown to the
specified torque.
Torque: 54 N
 m (5.5 Kg
 m/40 lb ft)
NOTE: Do not reuse the bolt and do not apply oil o
r
thread lock to the bolt.


015RS018
4. Piston and connecting rod assembly (8)

Apply engine oil to the cylinder bores, the
connecting rod bearings and the crankshaf
t
pins. Check to see that the piston ring end gaps
are correctly positioned.

6A-78 ENGINE MECHANICAL (6VE1 3.5L)



012RS001
7. Install oil pump assembly (5), refer to “Oil pump" in
this manual.
8. Install oil strainer and O-ring (4).
9. Install oil pipe and O-ring (3) and tighten the bolts.
Torque: 25 N
 m (2.5 Kg
 m/18 lb ft)
10. Install crankcase with oil pan (2).
1. Completely remove all residual sealant,
lubricant and moisture from the sealing
surfaces. The surfaces must be perfectly dry.
2. Apply a correct width bead of sealant (TB

1207C or its equivalent) to the contact surfaces
of the oil pan. There must be no gaps in the
bead.
3. The crankcase assembly must be installed
within 5 minutes after sealant application to
prevent premature hardening of the sealant.
4. Tighten the bolts and nuts to the specified
torque.
Torque : 10 N
 m (1.0 Kg
 m/7 lb ft)




013RW010
Legend
(1) Portion Between Bolt Holes
(2) Bolt Hole Portion

11. Install cylinder head assembly, refer to “Cylinder
head" in this manual.

ENGINE MECHANICAL (6VE1 3.5L) 6A-79
Piston and Connecting Rod
Piston, Connecting Rod and Associate Parts




015RW019
Legend
(1) Cylinder Head Assembly
(2) Cylinder Head Gasket
(3) Crankcase with Oil Pan
(4) Oil Pipe and O-Ring
(5) Oil Strainer and O-Ring
(6) Oil Gallery
(7) Piston and Connecting Rod Assembly
(8) Piston Ring
(9) Piston Pin
(10) Piston
(11) Connecting Rod
(12) Connecting Rod Cap


Disassembly
1. Remove cylinder head assembly (1). Refer to
“Cylinder Head Removal" in this manual. 2. Remove cylinder head gasket (2).
3. Remove crankcase with oil pan (3). Refer to ”Oil
Pan and Crankcase" in this manual.
4. Remove oil pipe and O-ring (4).

6A-80 ENGINE MECHANICAL (6VE1 3.5L)
5. Remove oil strainer and O-ring (5).
6. Remove oil gallery (6).
7. Remove connecting rod cap with connecting rod
lower bearing (12).
8. Remove piston and connecting rod assembly (7).
NOTE: Before removing piston and connecting rod
assembly, measure thrust clearance.






015RS031
 Remove any ridge or carbon build up from the
top end of the cylinder.
9. Remove the piston rings (8) with a piston ring
expander. Arrange the removed piston rings in the
cylinder number order.

015RS022
10. Remove the piston pin (9) using 5
8840
0551
0
piston pin service set and piston support with a
press.
NOTE: Keep the parts removed from each cylinde
r
separate. All parts must be reinstalled in their original
positions. Heating the connecting rod will permit easy
removal of the piston pin.


015RX001
Legend
(1) Press Ram
(2) Piston
(3) Connecting Rod
(4) Piston Pin

11. Piston (10)
12. Connecting rod (11)
Inspection and Repair
Pistons (10)
Carefully clean away all the carbon adhering to the
piston head and the piston ring grooves.
NOTE: Never use a wire brush to clean the pistons.
Damage will result. Visually check each piston fo
r
cracking, scoring, and other signs of excessive wear. If
any of the above conditions are found, the piston must
be replaced.
Piston Diameter
1. Measure the piston outside diameter with
micrometer at the piston grading position and a
right angle to the piston pin.
Piston grading position (from piston head)
Piston grading position : 43.0 mm (1.6929 in)