ABS ISUZU TF SERIES 2004 Repair Manual

8A-12 ELECTRICAL-BODY AND CHASSIS
ABBREVIATIONS
Abbreviation Meaning of abbreviation Abbreviation Meaning of abbreviation
A Ampere (S) LH Left hand
ABS Anti-lock brake system LWB Long wheel base
ASM Assembly MPI Multipart fuel injection
AC Alternating current M/T Manual transmission
A/C Air conditioner QOS Quick On Start system
ACC Accessories RH Right hand
CARB Carburetor RR Rear
C/B Circuit breaker RWAL Rear wheel anti-lock brake system
CSD Cold start device SRS Supplemental restraint system
DIS Direct ignition system ST Start
EBCM Electronic brake control module STD Standard
ECGI Electronic control gasoline injection SW Switch
ECM Engine control module SWB Short wheel base
ECU Electronic control unit TCM Transmission control module
EFE Early fuel evaporation V Volt
42 Two-wheel drive VSV Vacuum switching valve
44 Four-wheel drive W Watt (S)
FL Fusible link WOT Wide open throttle
FRT Front W/ With
H/L Headlight W/O Without
IC Integrated circuit
IG Ignition
kW Kilowatt

ELECTRICAL-BODY AND CHASSIS 8A-21

Caution:
Do not attach the booster cable to the discharged battery
negative terminal.

11. Start the engine of the vehicle with the booster battery.
Check that all unnecessary electrical accessories are off.
12. Start the engine of the vehicle with the discharged battery.
13. Remove the jumper cables in the reverse order to which
they were attached.
Caution:
Be absolutely sure to remove the negative jumper cable
from the vehicle with the discharged battery first.

ELECTRICAL-BODY AND CHASSIS 8A-25
Light Name Rated Power
V-W Number of
Bulbs Lens
Color Remarks
W/O Tacho 5Illumination light 14-2
W/ Tacho 7White
Turn Signal 14-1.12 2 Green
High Beam 14-1.12 1 Blue
Low Fuel 14-1.12 1 Amber
A/T Oil Temp 14-1.12 1 Red
Brake system 14-1.12 1 Red
4WD 14-1.12 1 Green
Seat belt 14-1.12 1 Red
Oil pressure 14-1.12 1 Red
ABS 14-1.12 1 Amber
SEDIMENTER 14-1.12 1 Red
AIR BAG 14-1.12 1 Red
Brake 14-1.12 1 Red
Charge 14-1.12 1 Red
Check Trans 14-1.12 1 Red
Check 4WD 14-1.12 1 Red
Power drive 14-1.12 1 Amber
3rd start 14-1.12 1 Green
4L 14-1.12 1 Green
Cruise Set 14-1.12 1 Green
Check Engine 14-1.12 1 Amber
Front Fog 14-1.12 1 Green
Rear foglight 14-1. 12 1 Amber
Glow 14-1.12 1 Amber
P LED 1 Green
R LED 1 Green
N LED 1 Green
D LED 1 Green
3 LED 1 Green
2 LED 1 Green












Indicator/
Warning
light
A/T shift
indicator
L LED 1 Green

ELECTRICAL-BODY AND CHASSIS 8A-31
FUSE AND SLOW BLOW FUSE LOCATION (RELAY AND FUSE BOX)
RELAY & FUSE BOX
RHD

FUSE 
ENGINE MODEL
FUSE NO. C24SE 6VE1 4JA1-TC / 4JH1-TC4JA1-L
EB-1 15A ECM 20A ECM 10A ECM 
EB-2 
10A ECM (B) 10A RR FOG 
EB-3 15A FRT FOG
10A TCM 15A FRT FOG 
EB-4 10A ACG (S) 15A FRT FOG  10A ACG (S)
EB-5 10A ILLUMI  10A ILLUMI & TAIL-RH10A ILLUMI
EB-6 10A TAIL  10A TAIL-LH 10A TAIL
EB-7 10A H/LIGHT-RH  10A H/LIGHT RH-LOW10A H/LIGHT RH
EB-8 10A H/LIGHT-LH  10A H/LIGHT LH-LOW10A H/LIGHT LH
EB-9 20A FUEL PUMP 10A O2 SENSOR 10A TRA ILER 
EB-10 10A O2 SENSOR 20A FUEL PUMP 10A AC G (S) 
EB-11 
10A H/LIGHT RH-HIGH 
EB-12 
10A H/LIGHT LH-HIGH
EB-13 10A A/C 
 
EB-14 10A 4WD
10A 4WD  
EB-15 10A HORN   
EB-16 15A HAZARD 10A HAZARD  

SLOW BLOW FUSE
ENGINE MODEL
FUSE NO. C24SE 6VE1 4JA1-TC / 4JH1-TC4JA1-L
SBF-1 100A MAIN 
80A MAIN 
SBF-2  
20A COND, FAN 
SBF-3  
60A GLOW 20A COND, FAN
SBF-4 20A COND, FAN 
30A ECM 50A GLOW
SBF-5 40A IG 1   
SBF-6 
40A ABS-1  
SBF-7 
30A ABS-2  
SBF-8 30A BLOWER   
SBF-9 50A IG 2

8A-32 ELECTRICAL-BODY AND CHASSIS
FUSE AND SLOW BLOW FUSE LOCATION (RELAY AND FUSE BOX)
RELAY & FUSE BOX
LHD

FUSE  Saudi Arabia
ENGINE MODEL
FUSE NO. C24SE 6VE1 4JA1-TC / 4JH1-TC4JA1-L
EB-1 15A ECM 20A ECM 10A ECM 
EB-2 
10A ECM (B) 10A RR FOG 
EB-3 15A FRT FOG
10A TCM 15A FRT FOG 
EB-4 10A ACG (S) 15A FRT FOG  10A ACG (S)
EB-5 10A ILLUMI & TAIL-RH  10A ILLUMI & TAIL-RH 
EB-6 10A TAIL-LH  10A TAIL-LH

EB-7 10A H/LIGHT-RH 10A H/LIGHT-RH
10A H/LIGHT-RH-LOW
 10A H/LIGHT RH-LOW
10A H/LIGHT-RH-LOW
EB-8 10A H/LIGHT-LH 10A H/LIGHT-LH
10A H/LIGHT-LH-LOW
 10A H/LIGHT LH-LOW
10A H/LIGHT-LH-LOW
EB-9 20A FUEL PUMP 10A O2 SENSOR 10A TRA ILER 
EB-10 10A O2 SENSOR 20A FUEL PUMP 10A AC G (S) 
EB-11
10A H/LIGHT-RH-HIGH
10A H/LIGHT RH-HIGH 
EB-12 10A H/LIGHT-LH-HIGH
10A H/LIGHT LH-HIGH 
EB-13 10A A/C 
 
EB-14 10A 4WD
10A 4WD  
EB-15 10A HORN   
EB-16 15A HAZARD 10A HAZARD  
SLOW BLOW FUSE
ENGINE MODEL
FUSE NO. C24SE 6VE1 4JA1-TC / 4JH1-TC4JA1-L
SBF-1 100A MAIN 
80A MAIN 
SBF-2  
20A COND, FAN 
SBF-3  
60A GLOW 20A COND, FAN
SBF-4 20A COND, FAN 
30A ECM 50A GLOW
SBF-5 40A IG 1   
SBF-6 
40A ABS-1  
SBF-7 
30A ABS-2  
SBF-8 30A BLOWER   
SBF-9 50A IG 2

ELECTRICAL-BODY AND CHASSIS 8A-105
REMOVAL AND INSTALLATION


ECM (ENGINE CONTROL MODULE):
C24SE

Removal
1. Lift both the ECM harness connector locking levers and
remove the two harness connectors form the ECM.
2. Remove the four socket head screws securing the ECM to
the mounting bracket.
3. Remove the ECM from the engine compartment
.


4. Pull out the ECM.
5. Disconnect both red and tan connectors.
Refer to the Section 6E-ENGINE of this Manual.
IMPORTANT: The replacement ECM must be programmed.
“SPS (Service Programming System) and immobiliser
programming (if equipped) is/are necessary”





Installation
Follow the removal procedure in the reverse order to install the
ECM.
Pay close attention to the important points mentioned in the
following paragraphs.



Connector
Be absolutely sure that ECM is securely connected.
This will prevent a poor contact and open circuit.

8A-106 ELECTRICAL-BODY AND CHASSIS
REMOVAL AND INSTALLATION


ECM (ENGINE CONTROL MODULE):
6VE1
Removal
1. Pull both the red ECM harness connector locks toward the
front of the vehicle, and remove the two harness connectors
form the ECM.
2. Remove the four hex-head screws securing the ECM to the
common chamber.
3. Remove the ECM from the engine compartment.


4. Pull out the ECM.
5. Disconnect both red and tan connectors.
Refer to the Section 6E-ENGINE of this Manual.
IMPORTANT: The replacement ECM must be programmed.
“SPS (Service Programming System) and immobiliser
programming (if equipped) is/are necessary”





Installation
Follow the removal procedure in the reverse order to install the
ECM.
Pay close attention to the important points mentioned in the
following paragraphs.



Connector
Be absolutely sure that ECM is securely connected.
This will prevent a poor contact and open circuit.

ELECTRICAL-BODY AND CHASSIS 8A-107
REMOVAL AND INSTALLATION


ECM (ENGINE CONTROL MODULE):
4JA1-TC / 4JH1-TC


Removal
1. Remove the passenger side front seat – refer to Section 10
CAB.
2. Remove the passenger side front door opening scuff plate.
3. Raise the carpet to gain access to the four hex-head bolts
securing the ECM and ECM cover to the floorpan
.
4. Remove the four hex-head bolts.
5. Pull the two harness connector locks away from the
harness connectors and then remove the connectors form
the ECM.
6. Remove the ECM from the vehicle.
Refer to the Section 6E-ENGINE of this Manual.
IMPORTANT: The replacement ECM must be programmed.
“SPS (Service Programming System) and immobiliser
programming (if equipped) is/are necessary”







Installation
Follow the removal procedure in the reverse order to install the
ECM.
Torque passenger seat securing bolts to the specified value –
refer to Section 10 CAB
Pay close attention to the important points mentioned in the
following paragraphs.



Connector
Be absolutely sure that ECM is securely connected.
This will prevent a poor contact and open circuit.

8A-108 ELECTRICAL-BODY AND CHASSIS
REMOVAL AND INSTALLATION


FUEL PUMP
Removal
1. Remove the fuel tank.
Refer to the Section 6C-ENGINE FUEL of this Manual.

Disconnect the fuel pipe.





Installation
Follow the removal procedure in the reverse order to install the
fuel pump.
Pay close attention to the important points mentioned in the
following paragraphs.



Rubber Seal
Be absolutely sure that the fuel pump rubber seals correctly
seated.

Connector
Be absolutely sure that the fuel pump connector is securely
connected.
This will prevent a poor contact and an open circuit.

ELECTRICAL-BODY AND CHASSIS 8A-129
Installation
Follow the removal procedure in the reverse order to install the
headlight.
Pay close attention to the important points mentioned in the
following paragraphs.


Connector
Be absolutely sure that the headlight connector is securely
connected.
This will prevent a contact and an open circuit.

This illustration is based on RHD model

LIGHTING SWITCH
Removal
1. Disconnect the battery ground cable.
2. Remove the steering wheel
1.
Refer to the “STEERING” Section of this manual.
3. Remove the Instrument panel lower cover
2.
4. Remove the steering column cover
3.


This illustration is based on RHD model
5. Disconnect the connector.
6. Remove the lighting switch from the steering shaft.





Installation
Follow the removal procedure in the reverse order to install the
lighting switch.
Pay close attention to the important points mentioned in the
following paragraphs.



Connector
Be absolutely sure that the lighting switch connector is securely
connected.
This will prevent a poor contact and an open circuit.


Wire Harness
Do not pinch the wire harnesses between the cluster and the
meter hood during the cluster installation procedure.
Wire damage will result.