Fuel sensor ISUZU TF SERIES 2004 Manual Online

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-71
Basic Knowledge of Tools Required
Lack of basic knowledge of this powertrain when
performing diagnostic procedures could result in an
incorrect diagnosis or damage to powertrain
components. Do not attempt to diagnose a powertrain
problem without this basic knowledge.
A basic understanding of hand tools is necessary to
effectively use this section of the Service Manual.
Serial Data Communications
Class II Serial Data Communications
This vehicle utilizes the “Class II" communication
system. Each bit of information can have one of two
lengths: long or short. This allows vehicle wiring to be
reduced by transmitting and receiving multiple signals
over a single wire. The messages carried on Class II
data streams are also prioritized. If two messages
attempt to establish communications on the data line at
the same time, only the message with higher priority will
continue. The device with the lower priority message
must wait. The most significant result of this regulation
is that it provides Tech 2 manufacturers with the
capability to access data from any make or model
vehicle that is sold.
The data displayed on the other Tech 2 will appear the
same, with some exceptions. Some scan tools will only
be able to display certain vehicle parameters as values
that are a coded representation of the true or actual
value. For more information on this system of coding,
refer to Decimal/Binary/Hexadecimal Conversions.On
this vehicle the Tech 2 displays the actual values fo
r
vehicle parameters. It will not be necessary to perform
any conversions from coded values to actual values.
On-Board Diagnostic (OBD)
On-Board Diagnostic Tests
A diagnostic test is a series of steps, the result of which
is a pass or fail reported to the diagnostic executive.
When a diagnostic test reports a pass result, the
diagnostic executive records the following data:

The diagnostic test has been completed since the
last ignition cycle.

The diagnostic test has passed during the curren
t
ignition cycle.

The fault identified by the diagnostic test is no
t
currently active.
When a diagnostic test reports a fail result, the
diagnostic executive records the following data:

The diagnostic test has been completed since the
last ignition cycle.

The fault identified by the diagnostic test is currently
active.

The fault has been active during this ignition cycle.

The operating conditions at the time of the failure.
Remember, a fuel trim DTC may be triggered by a list o
f
vehicle faults. Make use of all information available
(other DTCs stored, rich or lean condition, etc.) when
diagnosing a fuel trim fault.
Comprehensive Component Monitor
Diagnostic Operation
Input Components:
Input components are monitored for circuit continuity
and out-of-range values. This includes rationality
checking. Rationality checking refers to indicating a
fault when the signal from a sensor does not seem
reasonable, i.e.throttle position sensor that indicates
high throttle position at low engine loads. Inpu
t
components may include, but are not limited to the
following sensors:

Vehicle Speed Sensor (VSS)

Inlet Air Temperature (IAT) Sensor

Crankshaft Position (CKP) Sensor

Throttle Position Sensor (TPS)

Engine Coolant Temperature (ECT) Sensor

Camshaft Position (CMP) Sensor

Mass Air Flow (MAF) Sensor
In addition to the circuit continuity and rationality check
the ECT sensor is monitored for its ability to achieve a
steady state temperature to enable closed loop fuel
control.
Output Components:
Output components are diagnosed for proper response
to control module commands. Components where
functional monitoring is not feasible will be monitored fo
r
circuit continuity and out-of-range values if applicable.
Output components to be monitored include, but are no
t
limited to, the following circuit:

Idle Air Control (IAC) Valve

Control module controlled EVAP Canister Purge
Valve

Electronic Transmission controls

A/C relays

VSS output

MIL control
Refer to ECM and Sensors in General Descriptions.

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-77


F0: Diagnostic Trouble Code
F0: Read DTC Infor By Priority
F1: Clear DTC Information
F2: DTC Information
F0: History
F1: MIL SVS or Message Requested
F2: Last Test Failed
F3: Test Failed Since Code Cleared
F4: Not Run Since Code Cleared
F5: Failed This Ignition
F3: Freeze Frame/Failure Record
F1: Data Display
F0: Engine Data
F1: O2 Sensor Data
F2: Snapshot
F3: Miscellaneous Test
F0: Lamps
F0: Malfunction Indicator Lamps
F1: Relays
F0: Fuel Pump Relay
F1: A/C Clutch Relay
F2: EVAP
F0: Purge Solenoid
F3: IAC System
F0: RPM Control
F1: IAC Control
F4: Fuel System
F0: Fuel Trim Reset

F4: System Information
F0: MIL/System Status

F0: Diagnostic Trouble Code
The purpose of the "Diagnostic Trouble Codes" mode is
to display stored trouble code in the
ECM.
When "Clear DTC Information" is selected, a "Clea
r
DTC Information", warning screen appears.
This screen informs you that by cleaning DTC's "all
stored DTC information in the ECM will be erased".
After clearing codes, confirm system operation by test
driving the vehicle.
Use the "DTC Information" mode to search for a
specific type of stored DTC information.
History
This selection will display only DTCs that are stored in
the ECM's history memory. It will not display Type B
DTCs that have not requested the MIL ("Check Engine
Lamp"). It will display all type A and B DTCs tha
t
requested the MIL and have failed within the last 40
warm-up cycles. In addition, it will display all type C and
D DTCs that have failed within the last 40 warm-up
cycles.

MIL SVC or Message Request
This selection will display only DTCs that are requesting
the MIL. Type C and Type D DTCs cannot be displayed
using the MIL. Type C and D DTCs cannot be displayed
using this option.
This selection will report type B DTCs only after the MIL
has been requested.

Last Test Failed
This selection will display only DTCs that have failed the
last time the test run. The last test may have run during
a previous ignition cycle of a type A or type B DTC is
displayed. For type C and type D DTCs, the last failure
must have occurred during the current ignition cycle to
appear as last test fail.

Test Failed Since Code Cleared
The selection will display all active and history DTCs
that have reported a test failure since the last time
DTCs were cleared. DTCs that last failed more that 40
warm-up cycles before this option is selected will not be
displayed.

Not Run Since Code Cleared
This selection will display up to DTCs that have not run
since the DTCs were last cleared. Since any displayed
DTCs have not run, their condition (passing or failing) is
unknown.

Failed This Ignition
This selection will display all DTCs that have failed
during the present ignition cycle.

Freeze Frame/Failure Record
This selection will display stored various vehicle
information at the moment an emission related faul
t
when the MIL ("Check Engine Lamp") is commanded
on.
The Freeze Frame data will not be erased unless the
associated history DTC is cleared.

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-79
TYPICAL SCAN DATA & DEFINITIONS (ENGINE DATA)
Use the typical values table only after the On-Board Diagnostic System check has been completed, no DTC(s) were noted, and you have determined that the On-Board
Diagnostic are functioning properly.
Tech2 values from a properly running engine may be used for comparison with the engine you are diagnosing.
Condition : Vehicle stopping, engine running, air conditioning off & after warm-up (Coolant temperature approximately 80
C)

Tech 2
Parameter
Units Idle 2000rpm Definitions
1 Ignition Voltage V 10.0  14.5 10.0  14.5 This displays the system voltage measured by the ECM at ignition feed.
2 Engine Speed rpm 710  860 1950  2050 The actual engine speed is measured by ECM from the CKP sensor 58X signal.
3 Desired Idle
Speed rpm 750  770 750  770 The desired engine idle speed that the ECM commanding.
The ECM compensates for various engine loads.
4 Engine Coolant
Temperature
C or
F 80  90 (

) 80  90 (

) The ECT is measured by ECM from ECT sensor output voltage.
When the engine is normally warm upped, this data displays approximately 80 °C or
more.
5 Start Up ECT
(Engine Coolant
Temperature)
C or
F Depends on ECT
at start-up
Depends on ECT
at start-up
Start-up ECT is measured by ECM from ECT sensor output voltage when engine is
started.
6 Intake Air
Temperature

C or
F Depends on
ambient temp.
Depends on
ambient temp.
The IAT is measured by ECM from IAT sensor output voltage.
This data is changing by intake air temperature.
7 Throttle Position % 0 4  6 Throttle position operating angle is measured by the ECM from throttle position
output voltage.
This should display 0% at idle and 99  100% at full throttle.
8 Throttle Position
Sensor V 0.4  0.7 0.6  0.8 The TPS output voltage is displayed.
This data is changing by accelerator operating angle.
9 Mass Air Flow g/s 5.0  8.0 13.0  16.0 This displays intake air amount.
The mass air flow is measured by ECM from the MAF sensor output voltage.
10 Air Fuel Ratio 14.7:1 14.7:1 This displays the ECM commanded value.
In closed loop, this should normally be displayed around 14.2:1  14.7:1.
11 Idle Air Control Steps 10  20 20  30 This displays the ECM commanded position of the idle air control valve pintle.
A larger number means that more air is being commanded through the idle air
passage.
12 EGR Valve V 0.00 0.00  0.10 The EGR position sensor output voltage is displayed.
This data is changing by EGR valve solenoid operating position.
13 Desired EGR
Opening V 0.00 0.05  1.10 The ECM commanded EGR position sensor voltage is displayed.
According to the current position, ECM changes EGR valve solenoid operating
position to meet the desired position.
14 EGR Valve On
Duty % 0 32 – 38 This displays the duty signal from the ECM to control the EGR valve.
15 Engine Load % 2  7 8  15 This displays is calculated by the ECM form engine speed and MAF sensor reading.
Engine load should increase with an increase in engine speed or air flow amount.
16 B1 Fuel System
Status Open Loop/ Close
Loop Close Loop Close Loop
17 B2 Fuel System
Status Open Loop/ Close
Loop Close Loop Close Loop
When the engine is first started the system is in "Open Loop" operation.
In "Open Loop", the ECM ignores the signal from the oxygen sensors.
When various conditions (ECT, time from start, engine speed & oxygen sensor
output) are met, the system enters "Closed Loop" operation.
In "Closed Loop", the ECM calculates the air fuel ratio based on the signal from the
oxygen sensors.
18 Fuel Trim
Learned (Bank 1) Yes/No Yes Yes
19 Fuel Trim
Learned (Bank 2) Yes/No Yes Yes
When conditions are appropriate for enabling long term fuel trim corrections, fuel trim
learn will display "Yes".
This indicates that the long term fuel trim is responding to the short term fuel trim.
If the fuel trim lean displays "No", then long term fuel trim will not respond to changes
in short term fuel trim.
20 Injection Pulse
Bank 1 ms 2.0  4.0 2.0  4.0
21 Injection Pulse
Bank 2 ms 2.0  4.0 2.0  4.0
This displays the amount of time the ECM is commanding each injector On during
each engine cycle.
A longer injector pulse width will cause more fuel to be delivered. Injector pulse width
should increase with increased engine load.
22 Spark Advance °CA 10  15 35  42 This displays the amount of spark advance being commanded by the ECM.

6E-80 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Tech 2
Parameter
Units Idle 2000rpm Definitions
23 A/C Request (Air
Conditioning) On/Off Off Off This displays the air conditioner request signal. This should display "On" when the air
conditioner switch is switched on.
24 A/C Clutch On/Off Off Off This displays whether the ECM has commanded the A/C compressor clutch "On" or
"Off".
25 EVAP Purge
Solenoid
(Evaporative
Emission) % 50
80 0 This displays the duty signal from the ECM to control the canister purge solenoid
valve.
26 Fuel Trim Cell 49
52 13
17 This displays dependent on engine speed and MAF sensor reading.
A plot of engine speed versus MAF amount is divided into the cells.
Fuel trim cell indicates which cell is currently active.
27 Fuel Pump On/Off On On This displays operating status for the fuel pump main relay.
This should display "On" when the key switch is turned on and while engine is
running.
28 Deceleration Fuel
Cutoff Active/ Inactive Inactive Inactive The ECM will command the deceleration fuel mode when it detects a closed throttle
position while the vehicle is traveling.
While in decreasing fuel mode, the ECM will decrease the amount of fuel delivered
by entering open loop and decreasing the injector pulse width.
29 Power Enrichment Yes/No No No The ECM will command power enrichment mode "Yes" when a large increase in
throttle position and load is detected.
While in power enrichment mode, the ECM will increase the amount of fuel delivered
by entering open loop and increasing the injector pulse width.
30 Vehicle Speed km/h or mph 0 0 This displays vehicle speed.
The vehicle speed is measured by ECM from the vehicle speed sensor.
31 Cam Signal Present/ Missing Present Present This displays input signal from the camshaft position sensor.
When the correct pulse is generated, signal is received.
32 PSP Switch
(Power Steering
Pressure) Normal Pressure /
High Pressure Normal PressureNormal PressureThis displays the power steering pressure signal.
This should display "High Pressure" when the steering is steered.
33 Security Code
Status Programmable/
Not
Programmable Programmable Programmable This should display "Programmable" when the correct security code & secret code
are programmed.
34 Security Code Okay/ Not Okay Okay Okay This should display "Okay" when the security code is correctly accepted.
35 Immobilizer
System Normal /
Abnormal Normal Normal This should display "Normal" when the immobilizer is correctly operated.
36 Malfunction
Indicator Lamp On/Off Off Off This displays operating status for the Check Engine Lamp.
This should display "On" when the Check Engine Lamp is turned on.
37 Time From Start   This displays the engine time elapsed since the engine was started.
If the engine is stopped, engine run time will be reset to 00:00:00

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-81
TYPICAL SCAN DATA & DEFINITIONS (O2 SENSOR DATA)
Use the typical values table only after the On-Board Diagnostic System check has been completed, no DTC(s) were noted, and you have determined that the On-Board
Diagnostic are functioning properly.
Tech2 values from a properly running engine may be used for comparison with the engine you are diagnosing.
Condition : Vehicle stopping, engine running, air conditioning off & after warm-up (Coolant temperature approximately 80
C)

Tech 2
Parameter
Units Idle 2000rpm Definitions
1 Ignition Voltage V 10.0  14.5 10.0  14.5 This displays the system voltage measured by the ECM at ignition feed.
2 Engine Speed rpm 710  860 1950  2050 The actual engine speed is measured by ECM from the CKP sensor 58X signal.
3 Desired Idle
Speed rpm 750  770 750  770 The desired engine idle speed that the ECM commanding.
The ECM compensates for various engine loads.
4 Engine Coolant
Temperature
C or
F 80  90 (
C) 80  90 (
C) The ECT is measured by ECM from ECT sensor output voltage.
When the engine is normally warm upped, this data displays approximately 80 °C or
more.
5 Start Up ECT
(Engine Coolant
Temperature)
C or
F Depends on ECT
at start-up
Depends on ECT
at start-up
Start-up ECT is measured by ECM from ECT sensor output voltage when engine is
started.
6 Throttle Position % 0 4  6 Throttle position operating angle is measured by the ECM from throttle position
output voltage.
This should display 0% at idle and 99  100% at full throttle.
7 Throttle Position
Sensor V 0.4  0.7 0.6  0.8 The TPS output voltage is displayed.
This data is changing by accelerator operating angle.
8 Mass Air Flow g/s 5.0  8.0 13.0  16.0 This displays intake air amount.
The mass air flow is measured by ECM from the MAF sensor output voltage.
9 Air Fuel Ratio 14.7:1 14.7:1 This displays the ECM commanded value. In closed loop, this should normally be
displayed around 14.2:1  14.7:1.
10 Engine Load % 2  7 8  15 This displays is calculated by the ECM form engine speed and MAF sensor reading.
Engine load should increase with an increase in engine speed or air flow amount.
11 B1 Fuel System
Status Open Loop/ Close
Loop Close Loop Close Loop
12 B2 Fuel System
Status Open Loop/ Close
Loop Close Loop Close Loop
When the engine is first started the system is in "Open Loop" operation.
In "Open Loop", the ECM ignores the signal from the oxygen sensors.
When various conditions (ECT, time from start, engine speed & oxygen sensor
output) are met, the system enters "Closed Loop" operation.
In "Closed Loop", the ECM calculates the air fuel ratio based on the signal from the
oxygen sensors.
13 B1S1 O2 Sensor
(Bank1 Sensor 1)
mV 50  950 50 950
14 B2S1 O2 Sensor
(Bank2 Sensor 1)
mV 50  950 50  950
This displays the exhaust oxygen sensor output voltage.
Should fluctuate constantly within a range between 10mV (lean exhaust) and
1000mV (rich exhaust) while operating in closed loop.
15 B1 O2 Sensor
Ready (Bank 1)
Yes/No Yes Yes
16 B2 O2 Sensor
Ready (Bank 2)
Yes/No Yes Yes
This displays the status of the exhaust oxygen sensor.
This display will indicate "Yes" when the ECM detects a fluctuating oxygen sensor
output voltage sufficient to allow closed loop operation.
This will not occur unless the oxygen sensor is warmed up.
17 B1 Long Term
Fuel Trim (Bank
1)
% -10  20 -10  20
18 B2 Long Term
Fuel Trim (Bank
2)
% -10  20 -10  20
The long term fuel trim is delivered from the short term fuel term values and
represents a long term correction of fuel delivery for bank in question.
A value of 0% indicates that fuel delivery requires no compensation to maintain the
ECM commanded air fuel ratio.
A negative value indicates that the fuel system is rich and fuel delivery is being
reduced (decreased injector pulse width).
A positive value indicates that a lean condition exists and the ECM is compensating
by add fuel (increased injector pulse width).
Because long term fuel trim tends to follow short term fuel trim, a value in the
negative range due to canister purge at idle should not be considered unusual.
Excessive long term fuel trim values may indicate an rich or lean condition.

6E-82 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Tech 2
Parameter
Units Idle 2000rpm Definitions
19 B1 Short Term
Fuel Trim (Bank
1)
% -10
20 -10
20
20 B2 Short Term
Fuel Trim (Bank
2)
% -10
20 -10
20
The short term fuel trim to a bank represents a short term correction to the bank fuel
delivery by the ECM in response to the amount of time the bank fuel control oxygen
sensor voltage spends above or below the 450mV threshold.
If the oxygen sensor voltage has mainly remained less than 450mV, indicating a lean
air/fuel, short term fuel trim will increase into the positive range above 0% and the
ECM will pass fuel.
If the oxygen sensor voltage stays mainly above the threshold, short term fuel trim
will decrease below 0% into the negative range while the ECM reduces fuel delivery
to compensate for the indicated rich condition.
Under certain conditions such as extended idle and high ambient temperatures,
canister purge may cause short term fuel trim to read in the negative range during
normal operation.
Excessive short term fuel trim values may indicate an rich or lean condition.
21 Fuel Trim Cell 49
52 13
17 This displays dependent on engine speed and MAF sensor reading.
A plot of engine speed versus MAF amount is divided into the cells.
Fuel trim cell indicates which cell is currently active.
22 Fuel Trim
Learned (Bank 1) Yes/No Yes Yes
23 Fuel Trim
Learned (Bank 2) Yes/No Yes Yes
When conditions are appropriate for enabling long term fuel trim corrections, fuel trim
learn will display "Yes".
This indicates that the long term fuel trim is responding to the short term fuel trim.
If the fuel trim lean displays "No", then long term fuel trim will not respond to changes
in short term fuel trim.
24 B1S1 Status
(Bank 1 Sensor 1)
Rich / Lean Rich / Lean Rich / Lean
25 B2S1 Status
(Bank 2 Sensor 1)
Rich / Lean Rich / Lean Rich / Lean
This displays dependent on the exhaust oxygen sensor output voltage.
Should fluctuate constantly "Rich" and "Lean" in closed loop.

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-117
CIRCUIT DESCRIPTION
When the ignition switch is turned “ON," the Engine
Control Module (ECM) will turn “ON" the in-tank fuel
pump. The in-tank fuel pump will remain “ON" as long
as the engine is cranking or running and the ECM is
receiving 58X crankshaft position pulses. If there are no
58X crankshaft position pulses, the ECM will turn the
in-tank fuel pump “OFF" 2 seconds after the ignition
switch is turned “ON" or 2 seconds after the engine
stops running.
The in-tank fuel pump is an electric pump within an
integral reservoir. The in-tank fuel pump supplies fuel
through an in-line fuel filter to the fuel rail assembly. The
fuel pump is designed to provide fuel at a pressure
above the pressure needed by the fuel injectors. A fuel
pressure regulator, attached to the fuel rail, keeps the
fuel available to the fuel injectors at a regulated
pressure. Unused fuel is returned to the fuel tank by a
separate fuel return line.
TEST DESCRIPTION
Number(s) below refer to the step number(s) on the
Diagnostic Chart.
2. Connect the fuel pressure gauge to the fuel feed line
as shown in the fuel system illustration. Wrap a shop
towel around the fuel pressure connection in order to
absorb any fuel leakage that may occur when
installing the fuel pressure gauge. With the ignition
switch “ON" and the fuel pump running, the fuel
pressure indicated by the fuel pressure gauge
should be 333-376 kPa (3.4-3.8 kg/cm
2 / 48-55 psi).
This pressure is controlled by the amount o
f
pressure the spring inside the fuel pressure regulator
can provide.
3. A fuel system that cannot maintain a constant fuel
pressure has a leak in one or more of the following
areas:
 The fuel pump check valve.
 The fuel pump flex line.
 The valve or valve seat within the fuel pressure
regulator.
 The fuel injector(s).
4. Fuel pressure that drops off during acceleration,
cruise, or hard cornering may case a lean condition.
A lean condition can cause a loss of power, surging,
or misfire. A lean condition can be diagnosed using
a Tech 1 Tech 2. If an extremely lean condition
occurs, the oxygen sensor(s) will stop toggling. The
oxygen sensor output voltage(s) will drop below 500
mV. Also, the fuel injector pulse width will increase.

Important: Make sure the fuel system is not operating
in the “Fuel Cut-Off Mode."
When the engine is at idle, the manifold pressure is
low (high vacuum). This low pressure (high vacuum)
is applied to the fuel pressure regulator diaphragm.
The low pressure (high vacuum) will offset the
pressure being applied to the fuel pressure regulato
r
diaphragm by the spring inside the fuel pressure
regulator. When this happens, the result is lower fuel
pressure. The fuel pressure at idle will vary slightly
as the barometric pressure changes, but the fuel
pressure at idle should always be less than the fuel
pressure noted in step 2 with the engine “OFF."
16.Check the spark plug associated with a particula
r
fuel injector for fouling or saturation in order to
determine if that particular fuel injector is leaking. I
f
checking the spark plug associated with a particular
fuel injector for fouling or saturation does no
t
determine that a particular fuel injector is leaking,
use the following procedure:
 Remove the fuel rail, but leave the fuel lines and
injectors connected to the fuel rail. Refer to Fue
l
Rail Assembly in On-Vehicle Service.
 Lift the fuel rail just enough to leave the fuel
injector nozzles in the fuel injector ports.
CAUTION: In order to reduce the risk of fire and
personal injury that may result from fuel spraying
on the engine, verify that the fuel rail is positioned
over the fuel injector ports and verify that the fuel
injector retaining clips are intact.
 Pressurize the fuel system by connecting a 10
amp fused jumper between B+ and the fuel pump
relay connector.

Visually and physically inspect the fuel injector
nozzles for leaks.
17. A rich condition may result from the fuel pressure
being above 376 kPa (55 psi). A rich condition may
cause a DTC P0132 or a DTC P0172 to set.
Driveability conditions associated with rich conditions
can include hard starting (followed by black smoke)
and a strong sulfur smell in the exhaust.
20.This test determines if the high fuel pressure is due
to a restricted fuel return line or if the high fuel
pressure is due to a faulty fuel pressure regulator.
21.A lean condition may result from fuel pressure belo
w
333 kPa (48 psi). A lean condition may cause a DTC
P0131 or a DTC P0171 to set. Driveability conditions
associated with lean conditions can include hard
starting (when the engine is cold ), hesitation, poo
r
driveability, lack of power, surging , and misfiring.

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-133
Flash
Code Code Type DTC Name DTC Setting Condition Fail-Safe (Back Up) Recovery Condition Related Failure Parts Related
ECM Pin
No. Related
Multiple
DTC
P0131 A O2 Sensor Circuit Low Voltage
(Bank 1 Sensor 1) B21/
B22 P0171/
P1171/
P1172 P0151 A O2 Sensor Circuit Low Voltage
(Bank 2 Sensor 1) 1. No DTC relating to ECT sensor, CMP sensor,
CKP sensor, VSS, injector control circuit,
ignition control circuit and O2 sensor circuit no
activity (bank 1 & 2).
2. Engine speed is between 1000rpm and
4000rpm.
3. Engine coolant temperature is between 70
C
and 110
C.
4. Vehicle speed is between 0km/h and
120km/h.
5. Engine load is between 80% and 160%.
6. Throttle position fluctuation is below 0.28V.
7. O2 sensor bank 1 or bank 2 output voltage is
more than 400mV for 50 seconds. "Open Loop" fuel control. O2 sensor bank 1 or bank 2
output voltage is below 400mV
for 50 seconds. 1. Sensor harness open or short to ground
circuit.
2. O2 sensor malfunction.
3. MAF sensor output is incorrect.
4. Air intake line malfunction.
5. IAC valve malfunction.
6. Low fuel pressure.
7. Injector malfunction.
8. ECM malfunction.
B23/
B24 P0174/
P1171/
P1172 P0132 A O2 Sensor Circuit High Voltage
(Bank 1 Sensor 1) B21/
B22 P0172 P0152 A O2 Sensor Circuit High Voltage
(Bank 2 Sensor 1) 1. No DTC relating to ECT sensor, CMP sensor,
CKP sensor, VSS, injector control circuit,
ignition control circuit and O2 sensor circuit no
activity (bank 1 & 2).
2. Engine speed is between 1000rpm and
4000rpm.
3. Engine coolant temperature is between 70
C
and 110
C.
4. Vehicle speed is between 0km/h and
120km/h.
5. Engine load is between 80% and 160%.
6. Throttle position fluctuation is below 0.28V.
7. O2 sensor bank 1 or bank 2 output voltage is
below 600mV for 50 seconds. "Open Loop" fuel control. O2 sensor bank 1 or bank 2
output voltage is more than
600mV for 50 seconds. 1. Sensor harness open or short to ground
circuit.
2. O2 sensor malfunction.
3. MAF sensor output is incorrect.
4. Air intake line malfunction.
5. AC valve malfunction.
6. Low fuel pressure.
7. Injector malfunction.
8. EVAP purge solenoid valve malfunction.
9. Ignition system malfunction.
10. Spark plug malfunction.
11. ECM malfunction. B23/
B24 P0175 P0134 A O2 Sensor Circuit No Activity
Detected (Bank 1 Sensor 1) B21/
B22 -
15

P0154 A O2 Sensor Circuit No Activity
Detected (Bank 2 Sensor 1) 1.No DTC relating to MAF sensor, ECT sensor,
CMP sensor, CKP sensor, VSS, injector
control circuit and ignition control circuit.
2. Engine coolant temperature is more than
70
C.
3. Vehicle speed is more than 60km/h.
4. O2 sensor bank 1 or bank 2 output voltage is
between 350mV and 600mV. "Open Loop" fuel control. O2 sensor bank 1 or bank 2
output voltage is below 0.35mV
consecutively.
OR
O2 sensor bank 1 or bank 2
output voltage is more than
600mV consecutively. 1. O2 sensor malfunction.
2. ECM malfunction.
B23/
B24 -

6E-134 3.5L ENGINE DRIVEABILITY AND EMISSIONS Flash
Code Code Type DTC Name DTC Setting Condition Fail-Safe (Back Up) Recovery Condition Related Failure Parts Related
ECM Pin
No. Related
Multiple
DTC
P0171 B O2 Sensor System Too Lean
(Bank 1) - -
44
P0174 B O2 Sensor System Too Lean
(Bank 2) 1. No DTC relating to MAF sensor, IAT sensor,
ECT sensor, TPS, CMP sensor, CKP sensor,
VSS, injector control circuit, ignition control
circuit, O2 sensor circuit low voltage & high
voltage (bank 1 & 2) and O2 sensor circuit no
activity (bank 1 & 2).
2. Engine speed is more than 600rpm.
3. Intake air temperature is more than 50
C.
4. Engine coolant temperature is between 35
C
and 120
C.
5. Engine load is more than 20.
6. EVAP purge solenoid valve on-duty is below
100%.
7. Air-fuel ratio correction volume is more than
150% for 20 seconds. No fail-safe function. Air fuel ratio correction volume
is between 50% and 150% for
5 seconds. 1. Sensor harness open or short to ground
circuit.
2. O2 sensor malfunction.
3. MAF sensor output is incorrect.
4. Air intake line malfunction.
5. IAC valve malfunction.
6. Low fuel pressure.
7. Injector malfunction.
8. ECM malfunction.
- -
P0172 B O2 Sensor System Too Rich
(Bank 1) - -
45
P0175 B O2 Sensor System Too Rich
(Bank 2) 1. No DTC relating to MAF sensor, IAT sensor,
ECT sensor, TPS, CMP sensor, CKP sensor,
VSS, injector control circuit, ignition control
circuit, O2 sensor circuit low voltage & high
voltage (bank 1 & 2) and O2 sensor circuit no
activity (bank 1 & 2).
2. Engine speed is more than 600rpm.
3. Intake air temperature is more than 50
C.
4. Engine coolant temperature is between 35
C
and 120
C.
5. Engine load is more than 20.
6. EVAP purge solenoid valve on-duty is below
100%.
7. Air-fuel ratio correction volume is below 50%
for 20 seconds. No fail-safe function. Air fuel ratio correction volume
is between 50% and 150% for
5 seconds. 1. Sensor harness open or short to ground
circuit.
2. O2 sensor malfunction.
3. MAF sensor output is incorrect.
4. Air intake line malfunction.
5. AC valve malfunction.
6. Low fuel pressure.
7. Injector malfunction.
8. EVAP purge solenoid valve malfunction.
9. Ignition system malfunction.
10. Spark plug malfunction.
11. ECM malfunction. - -

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-135
Flash
Code Code Type DTC Name DTC Setting Condition Fail-Safe (Back Up) Recovery Condition Related Failure Parts Related
ECM Pin
No. Related
Multiple
DTC
P1171 D Fuel Supply System Lean
During Power Enrichment
(Bank 1) B21/
B22/
-
44
P1172 D Fuel Supply System Lean
During Power Enrichment
(Bank 2) 1. No DTC relating to MAF sensor, IAT sensor,
ECT sensor, TPS, CMP sensor, CKP sensor,
VSS, injector control circuit, ignition control
circuit, O2 sensor circuit low voltage & high
voltage (bank 1 & 2) and O2 sensor circuit no
activity (bank 1 & 2).
2. Engine speed is between 1000rpm and
6000rpm.
3. Intake air temperature is below 70
C.
4. Engine coolant temperature is between 30
C
and 120
C.
5. Engine load is between 150 and 255.
6. Throttle position output is more than 2.22V
and fluctuation is below 0.28V.
7. Except fuel cut operation.
8. O2 sensor output voltage below 250mV for 10
seconds. No fail-safe function.
O2 sensor output voltage is
more than 520mV for 5
seconds.
1. Sensor harness open or short to ground
circuit.
2. O2 sensor malfunction.
3. MAF sensor output is incorrect. 4. Air intake
line malfunction.
5. IAC valve malfunction.
6. Low fuel pressure.
7. Injector malfunction.
8. ECM malfunction.
B23/
B24 -
P0201 A Injector 1 Control Circuit
A36 - P0202 A Injector 2 Control Circuit
B3 - P0203 A Injector 3 Control Circuit
A35 - P0204 A Injector 4 Control Circuit
B4 - P0205 A Injector 5 Control Circuit
A34 -
31
P0206 A Injector 6 Control Circuit 1. No DTC relating to CMP sensor and CKP
sensor.
2. Under sequential injection.
3. Injection pulse is between 2.5ms and 7.5 ms.
4. Except fuel cut operation.
5. Engine speed is between 600rpm and
2000rpm.
6. 30 injection signals are not detected
consecutively. No fail-safe function. 30 injection signals are
detected consecutively. 1. Injector harness open circuit, short to ground
or short to voltage.
2. Injector malfunction.
3. ECM malfunction.
B5 -