pcm JAGUAR S TYPE 1999 1.G Powertrain Manual

V6 Engine AJ-V6/AJ28
38
J.303.1348
Generator
The 120AH generator is fitted with a special casing
to enable it to be bolted directly to the engine via
three fixing points.
On the manual transmission vehicles, sudden
deceleration may result in generator momentum
driving the belt against the engine which is
slowing down, with possible effects on the life of
the drive belt. The generator pulley fitted to the
manual transmission vehicle incorporates a clutch
mechanism which allows it to freewheel in the
reverse drive (anti-clockwise) direction. Note that
a special tool is required to remove the pulley.
To improve generator control on all
engine/transmission variants, the generator now
has a four pin connector to provide two new
sensing signals:
¥ pin S is directly connected to the battery to
provide voltage feedback to the regulator
¥ the regulator senses field current and
produces a PWM signal from pin FR to the
PCM to indicate the generator duty cycle.
D.303.1350
DRIVE BELT TENSIONER
GENERATOR
D.303-1350
Drive Belt Tensioner
The drive belt tensioner is a similar type to that
fitted to the V8 engines. An index on the
tensioned arm rotates with wear against three
markings on the tensioner spring cap which
indicate the minimum and maximum lengths for a
new belt and the point at which the belt must be
replaced.
Replace Belt
Belt Wear
Indicator
New Belt Maximum Length
New Belt Minimum Length
Manual
transmission
pulleyAutomatic
transmission
pulley
J.303.1348

V8 Engine AJ-V6/AJ28
54
Engine Management Sensors
The configuration of the AJ28 engine management sensors is changed from the previous V8 variants:
¥ New components unique to AJ28 engine are the MAF sensor and engine fuel temperature (EFT)
sensor.
¥ Components in common with the V6 engine are the IAT sensor, KS sensors, injector pressure (IP)
sensor, engine oil temperature (EOT) sensor and HO2 sensors.
¥ The crankshaft (CKP) and camshaft (CMP) sensors are the same as those fitted to the AJ27 engine.
Heated Oxygen (HO2) Sensors
Upstream and dowmstream HO2 sensors are
fitted and are of the type used on the V6 engine
(the linear type sensor is not used).
J.303.1387
HO2 SENSORS
J.303.1387
J.303.1281
COIL ON PLUG UNIT
J.303.1281
Ignition System
The coil-on-plug ignition modules are specific to
the AJ28 engine and are triggered directly from
the PCM. Double electrode platinum plugs are
fitted.

V8 Engine AJ-V6/AJ28
56
Fuel Injection
Returnless Fuel System
The function and operation of the returnless fuel
system is the same as that fitted to the V6 engine
but with different fuel pipework to suit the V8
layout. The air assisted, top fed, fuel injectors are
supplied from two separate rails joined by an
interconnecting cross-over pipe (similar to AJ27)
with a single common feed from the fuel tank.
The fuel rail assembly is removeable. An engine
fuel temperature (EFT) sensor and injector
pressure (IP) sensor provide feedback to the PCM
to control the fuel pump flow rate (see ÔS-TYPE
IntroductionÕ Technical Guide). Note that the EFT
sensor is not in direct contact with the fuel (ÔdryÕ
type sonser).
J.303.1390
FUEL RAIL ASSEMBLY
IP Sensor
EFT Sensor
J.303.1390

Automatic TransmissionAJ-V6/AJ28
61
Introduction
The 5R55N type 5-speed automatic transmission is fitted to both the V6 and V8 engines. The
transmission is controlled electronically by the powertrain control module (PCM) without the use of a
dedicated control module. Normal P, R, N, D drive functions plus manual selection of 4th, 3th and 2nd
gears are provided by a Jaguar style ÔJÕ gate (not the same as XJ and XK Series - see ÔS-TYPE IntroductionÕ
Techical Guide). Sports mode and traction assistance are selected at the ÔJÕ gate.
Specification
Transmission weight with fluid: 90 kg (198 lbs)
Oil type: Mercon V semi-synthetic (not compatible with other fluids)
Oil capacity: 9 Litres (9.5 quarts) - new
5 Litres (5.3 quarts) - after draining
Oil Fill/change: Filled for life, no top up required (no dipstick)
Gear ratios: 1st 2nd 3rd 4th 5th Rev
3.24 : 1 2.44 : 1 1.55 : 1 1 : 1 0.75 : 1 3.07 : 1
D.307.313
5R55N AUTOMATIC TRANSMISSION
D.303.313
Vent Tube
Turbine Speed
Sensor
Intermediate
Speed Sensor
Output Speed
Sensor
Range Switch
Rear Mounting
BracketJ-gate Selector
Cable Lever

Automatic TransmissionAJ-V6/AJ28
63 controlled solenoid are mounted on an
integral, replaceable, control module
¥ three speed sensors mounted on the external
casing: turbine speed sensor, intermediate
speed sensor and output speed sensor
¥ an oil temperature sensor is fitted inside the
transmission.
The gear select lever is connected via a Bowden
cable to an operating lever on the left side of the
transmission casing. A digital rotary switch, the
transmission range switch, fits over the shaft of
the operating lever and is fixed by two bolts to
the transmission casing. Selection of a particular
drive function generates a 4 bit binary coded
signal which is transmitted directly to the PCM
over a four wire parallel interface. As on the XK
and XJ Series, lateral movement of the gear select
lever across the gate, D to 4 or 4 to D, operates a
switch which indicates the selected function to
the PCM (the Bowden cable is not actuated
laterally).
The PCM directly controls the transmission
actuators as a response to driver demand, engine
requirements and according to the selected shift
mode. Gear selection is controlled by commands
to the four shift solenoids. If, during gear
selection, the relative speeds monitored by the
speed sensors are not as expected, the PCM
varies the analogue signal to the variable force
solenoids to increase/decrease the clutch pressure
(closed loop control). Increased engagement times
due to ageing are also controlled by adaptive shiftpressure.
Apart from the sports mode and traction mode
selected by the driver, there are pre-programmed
modes selected by the PCM in response to sensed
driving conditions :
¥ increased load such as gradients and trailer
towing
¥ cruise control
¥ hot mode: strategies including clutch lock up
are applied to reduce heat.
Transmission Oil Cooler
The transmission fluid is cooled externally by a
dedicated oil to air radiator which is mounted in
the integral cooling pack between the engine
radiator and A/C condenser and below the PAS
cooler.
D.307.320
TRANSMISSION OIL COOLING
Transmission
Oil Cooler
D.307.320

Introduction
Manual Transmission AJ-V6/AJ28
64In Europeon markets only, manual transmission is fitted as standard on the V6 entry S-TYPE model and
as an option on the V6 high specification model. Manual transmission is not available for the V8 variant.
The manual transmission is a 5 speed Getrag 221 unit with the following features:
¥ direct gearing (1:1) on 5th gear (it is normally on 4th) reduces losses
¥ twin synchronising cones on 1st and 2nd gears provide a smoother change
¥ four plane shift gate (R-1-3-5) with Ôknock-overÕ protection on the Reverse position.
A reverse light switch and speed sensor are fitted on the LH side of the gearbox. The speed sensor
monitors output shaft speed to provide an input to the PCM in addition to the signals received from the
road wheel speed sensors.
Specification:
Gear ratios: 1st 2nd 3rd 4th 5th Reverse
4.23 : 1 2.52 : 1 1.67 : 1 1.22 : 1 1 : 1 4.14 : 1
Weight: 33 kg (72 lbs)
Oil specification: ESSOD21065
Oil change interval: 60,000 miles (96,000 km)
D.307.312
MANUAL TRANSMISSION, CLUTCH ASSEMBLY AND DUAL MASS FLYWHEEL
D.307.312
Reverse Light Switch
Speed Sensor

Powertrain ManagementAJ-V6/AJ28
69
Introduction
All powertrain and associated management
functions are controlled from a single unit, the
powertrain control module (PCM). These
functions are as follows:
¥ overall monitoring and control of
performance, fuel economy, emissions,
driveability and safety
¥ receives and processes direct inputs from
engine, transmission, fuel system and
ancillary systems sensors
¥ provides direct control of actuator devices
¥ communicates with other modules via the
SCP bus (eg to obtain wheel speed
information)
¥ provides system diagnostics to conform to
OBDII requirements.
Powertrain Control Module (PCM)
The basic PCM is common to the V6 and V8
engines but with unique programming to suit the
respective engine characteristics and some
differences in the interface circuits for the
different sensors and actuators.
The PCM is located below the LH or RH mounted
A/C evaporator/blower unit and has a single
connector panel which protrudes through the
forward bulkhead into the engine bay.
The PCM has three connectors:
¥ a 60 pin connector which provides the
interfacing with the engine wiring harness:
carries engine mounted sensor inputs and
output control signals
¥ a 32 pin connector which carries the
transmission sensing and control signals and
also the rear HO2 sensor inputs
¥ a 58 pin connector which carries non engine
mounted sensor and actuator signals and
provides the PCM link to the SCP bus.
Powertrain Sub-Systems
Brief descriptions of PCM control of new
subsystems are given in the relevant engine and
transmission sections (electronic throttle,
returnless fuel etc).
J.303.1393
POWERTRAIN CONTROL MODULE
J.303.1393