engine JAGUAR XFR 2010 1.G Workshop Manual
Page 908 of 3039
Engine - V8 S/C 5.0L Petrol - Crankshaft Front Seal
Removal and Installation Published: 11-May-2011
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
2. Refer to: Crankshaft Pulley (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).
3. CAUTION: Do not over tighten the crankshaft front seal.
Failure to follow this instruction may result in damage to
the vehicle.
Special Tool(s): 303-1434 303-1434
Remover/Installer, Front Crankshaft Seal Special Tool(s)
Page 911 of 3039
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
2. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
3. Refer to: Cooling Fan Motor and Shroud - Vehicles With: Supercharger (303-03C Engine Cooling - V8 5.0L Petrol/V8 S/C 5.0L Petrol, Removal
and Installation).
4. Refer to: Starter Motor (303-06C Starting System - V8 5.0L Petrol/V8 S/C 5.0L Petrol, Removal and Installation).
5. www.JagDocs.com
Page 921 of 3039
2. CAUTION: Install a new friction washer before
installing the crankshaft pulley.
NOTES:
Make sure to clean the threads in the end of the
crankshaft and that the crank nose is free of any foreign
materials.
Skip to step 11 for engines fitted with early RH thread
crankshaft bolt.
3. Install the special tool. www.JagDocs.com
Page 929 of 3039
5.0L Petrol, Removal and Installation).
23. Refer to: Cooling Fan Motor and Shroud - Vehicles With: Supercharger (303-03C Engine Cooling - V8 5.0L Petrol/V8 S/C 5.0L Petrol, Removal
and Installation).
24. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
Page 930 of 3039
Engine - V8 S/C 5.0L Petrol - Crankshaft Rear Seal
Removal and Installation
Special Tool(s)
Removal
NOTE: Removal steps in this procedure may contain installation details. Published: 12-May-2014
1. Refer to: Flexplate (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).
2. 303-1442
Rear Crankshaft Seal Installer JLR-303-1622
Alignment Tool, Engine Rear Oil Seal
Page 933 of 3039
Torque: 11 Nm
6. Refer to: Flexplate (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).
Page 934 of 3039
Engine - V8 S/C 5.0L Petrol - Cylinder Head LH
Removal and Installation
Removal
NOTE: Removal steps in this procedure may contain installation details. Published: 18-May-2012
1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
2. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
3. Refer to: Camshaft LH (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).
4. Refer to: Exhaust Manifold LH (303-01C Engine - V8 5.0L Petrol, Removal and Installation).
5.
6.
Page 935 of 3039
7.
8.
9.
10. CAUTION: Discard the seal.
NOTE: Engine shown removed for clarity.
NOTE: Clamp the hose to minimize coolant loss.
Page 942 of 3039
7.
8.
9.
10. Torque: 25 Nm
NOTE: Tighten the bolts in the indicated sequence.
Torque: 12 Nm
CAUTIONS:
If a new cylinder head has been installed then new
tappets must be installed.
If the cylinder head is being removed without a new
component being installed, the tappets must be installed in
their original positions.
Lubricate the valve tappets with clean engine oil.
Torque: 10 Nm
Page 944 of 3039
14.
15.
16.
CAUTION: Install a new seal.
NOTE: Engine shown removed for clarity.
Torque: 12 Nm