change wheel JAGUAR XK 2011 1.G Quick Start Guide

Manual gear changes
The steering wheel paddles allow manual gear
changing with eitherDrive orSport selected.
• To shift down, briefly pull the paddle.
• To shift up, briefly pull the +paddle.
When the paddles are used in Drive, gear
selection will revert to automatic mode if use of
the paddles is not maintained.
With Sport selected, continuous manual
operation is initiated if the paddles are used.
In both Dand Smode, automatic operation can
be reinstated by pulling the +paddle for two
seconds.
9
Electric parking brake
• Apply manually when stationary in Park,Drive
or Reverse by pulling up the parking brake
switch.
• Can be manually released when the engine is running and the foot brake is applied. Press
the parking brake switch down to release.
• If manually applied whilst in Drive orReverse,
the parking brake will automatically
release when the accelerator is applied.
• Releases automatically when the gear selector is moved from Park.
Transmission
Gearshift interlock
The ignition must be on and the footbrake
depressed before the selector can be rotated
from thePark position. Maintain brake pressure
until a gear is selected.
Instrument pack message center
The current gear selection will be displayed at
the top of the message center.
Sport mode
To move from Drive toSport, press the gear
selector down and rotate. Automatic gear
changing continues but the gearshift points are
modified for full use of the engine's power.
Do NOT use the recess in the electric parking
brake as a storage area.
If the engine is switched off with Neutral selected,
automatic selection of Pis delayed for \f0 minutes.
Do NOT use this feature during vehicle recovery.
jjm 18 96 30 101:XK NAS 10MY.qxd 04/09/2008 15:24 Page 9 PR NDS
START
ENGIN E
STOP

When a vehicle ahead enters the same lane as
you, or a slower vehicle is encountered in the
same lane, road speed will be adjusted to
maintain the currently selected gap.The warning lamp will illuminate to
indicate that the vehicle is in follow
mode.
ACCIS NOT a collision warning or avoidance
system. Additionally the system WILL NOTdetect:
• Stationary or slow moving vehicles below 6 mph (\f0 km/h).
• Pedestrians or objects in the roadway.
• Oncoming vehicles in the same lane.
Cruise (speed) control and ACC
1. SET \b use to set the road speed to be
maintained or increase/decrease the speed
in \f mph (2 km/h) steps when cruise control
is operating.
2. RESUME \b use to resume a set speed
retained in memory.
\f. CANCEL \b cancels cruise control but
retains the set speed in memory.
ACC only
4. GAP \b use to increase/decrease the time gap
to the vehicle ahead. The gap can be set to
one of four pre\bdefined settings, the largest
gap depicted by four chevrons.
The gap setting will be displayed in the
message center.
Dependent upon specification, your vehicle will be fitted with either the standard cruise control system or
the Adaptive \fruise \fontrol system (A\f\f). Both systems allow you to maintain a set speed until either
cruise control is cancelled or the brake pedal is used. A\f\f also allows you to maintain a gap between
yourself and the vehicle ahead when the speed of that vehicle is not greater than yours. Both systems are
controlled via switches on the steering wheel.
Cruise (speed) control and Adaptive Cruise Control
\f0
Driving
Cruise control will automatically disengage when
the foot brake is pressed or when the vehicle
speed falls below \f8 mph (28 km/h).
Forward alert
Forward Alert is a feature of the Adaptive \fruise \fontrol system. It provides limited detection and warning
of a vehicle in the road ahead.
1. Press to
activate.
The warning lamp in the instrument
pack will illuminate.There are four sensitivity settings and the
message center will confirm which setting is
selected. The setting can be changed by using
theGAP control (see 4above) while ACC is not
engaged.
The system will display warnings in the
message center even if ACC is not engaged.
jjm 18 96 30 101:XK NAS 10MY.qxd 04/09/2008 15:24 Page 101
2
4
3 1

Calls via the touchscreen
Making a call
1.With a paired and active phone, select
Phone orComms from the Home screen.
2. From the Digit Dial screen, enter the number
using the on\bscreen keypad.
\f. Touch on the screen. The call
duration appears on the screen.
4. To end the call touch .
Calls via the steering wheel
1. Press and hold the Sourcebutton to access
phone mode on the touch screen and
message center. Use the scroll control to
find the desired phonebook contact.
2. To make or receive a call, press on the
steering wheel.
\f. To end a call, press again.
\f5
Bluetooth® cell phones
Cell phone
Compatible Bluetooth cell phones can
communicate with the inbuilt telephone system.
Connection must be made with ignition on or
engine running.
Use the following procedures in conjunction with
your Bluetooth phone manufacturer’s
instructions.
Pairing your cell phone to the vehicle
With the ignition on, touch\bscreen active and no
phone currently docked:
1. Start the Bluetooth search function on your
cell phone.
2. Your phone will list any Bluetooth
devices found. Select Jaguarfrom the list.
\f. Now enter the Bluetooth PIN 1\f1\finto your
cell phone.
The phone should now pair and dock to the
vehicle system.
To undock a cell phone, select Phonevia the
touch\bscreen then Settingsfollowed by
Undock.
Downloading phonebook entries
When a cell phone with phonebook download
capability is paired and docked, its phonebook
directory will automatically download to the
vehicle system.
The vehicle phonebook will be updated each
time a cell phone is docked to the system.
To change the Auto download setting via the
touch\bscreen, touch Phone, select Phone
options thenPhonebook . Apply the change.
Jaguar Bluetooth Connectivity
For the latest list of compatible phones and their
software, refer to
http:\b\bwww.jaguar.com\bus\ben\bxk\bmodels_pricing\b
features\bfeatures_convenience.htm.
Operating note: ‘Docking’ and ‘docked’ are terms
used in relation to a paired phone that is fully
linked to the vehicle system and can be used for
calls. The cell phone is not physically docked in a
cradle.
Cell phone auto connect
The phone may request 'set authorisation ' or
'always allow'. If this is set the phone will
subsequently connect automatically.
jjm 18 96 30 101:XK NAS 10MY.qxd 04/09/2008 15:24 Page 15 Phone
12: 26 pm
Last N
amesP hone
D igi tDia l
Options Settings