oil filter JEEP CJ 1953 Service Manual

'Jeep*
UNIVERSAL SERIES
SERVICE
MANUAL

B
LUBRICATION
AND
PERIODIC SERVICES

Contents
PAR. SUBJECT
PAR.
SUBJECT

GENERAL
.B-l
Chassis
Lubrication
B-7
Engine
Lubrication System B-4, B-6

Special
Lubricants B-2

Fresh
Lubricant.
.B-3

LUBRICATION CHARTS
. Pages 8, 9

SERVICE
MAINTENANCE SCHEDULE.
.B-8
Air
Cleaner
B-2
5,
B-2
6
Air
Filter
—
F.E.E.C.
System Canister
B-2
4

Axle
U-Bolts B-49 Body
Lube
Points: B-65 Hood Hinge Pivot Points B-66

Glove
Compartment Door
Latch
B-6
7
Tailgate Hinges .B-68

Brakes,
Adjust .B-41
Brake
Linings .B-42

Brake
Master Cylinder B-40
Charging
Circuit
B-l9
Clutch
. B-43, B-44
Cooling System—Radiator. B-28, B-29 Differentials
........
.B-50, B-51, B-52, B-53

Distributor
B-14, B-l5

Engine
Oil B-9
Engine
Oil
Filter
B-10, B-ll

Engine
Tune-Up B-20
Exhaust
Emission Control System
B-2
2

Exhaust
Manifold Heat Control Valve. . . .B-l2

Exhaust
System
B-2 3
Fan
Belt . .B-21
Front
Axle U-Joint B-54, B-55

Generator
.B-16
Headlights B-61
Heater Controls B-62
Lights
and Controls B-59 Positive Crankcase Ventilation Valve. . . .B-l3
Shock Absorbers B-48
Spark
Plugs. B-17
Speedometer Cable. .B-60

Spring
Bushings.. . .B-46

Spring
Shackles .B-47
Steering
Gear
B-2 7
B-l. GENERAL
All
'Jeep' Universal vehicles require periodic
lubri­

cation and other maintenance services for normal
vehicle
usage
and application to promote satis­ factory operation and prevent
excessive
wear. Un­
der severe operating or atmospheric conditions
these
services should be performed more
often
than
under normal conditions. It should also be remem­
bered that common short trips and
stop-and-go
driving
are more severe on lubrication
points
than
Starting
Circuit
B-l8

Tie
Rod and Drag
Link
Sockets
.
B-45

Tires
B-64

Transmission
and Transfer Case—
Lubricant
Level
Check B-30

General
B-31

Transfer
Case B-32
Transmission
.B-33

Transmission
and Transfer
Case
—

Lubricant
Change .B-34
General
.B-35

Transfer
Case B-36
Transmission
B-3
7, B-38

Transfer
Case Linkage B-39

Universal
Joints and Slip Joints.
.......
.B-58

Wheel
Bearings..
.........
. . .B-56, B-57
Windshield
Wiper and Washer B-63

LUBRICATION
OF

OPTIONAL EQUIPMENT
B-69
Centrifugal
Governor. .B-71
Pintle Hook .B-70

Powr-Lok
or
Trac-Lok
Differential B-72

PARTS REQUIRING
NO LUBRICATION.
. . .B-73

Alternator
Bearings. B-76
Clutch
Release Bearings.
.............
.B-74
Shock Absorbers B-78
Springs
B-7
7
Starter
Motor Bearings B-75

Water
Pump Bearings B-74

LUBRICATION REQUIREMENTS FOR OFF-HIGHWAY OPERATIONS
B-79

Air
Cleaner B-82

Chassis
Lubrication
B-83

Engine
Oil B-80
Engine
Oil
Filter
B-81
Differentials .B-86
Front
Axle U-Joints. B-84
Transfer
Case and Transmission .B-85
constant
speed
driving on highways, and even more
intensified in extreme cold or hot weather; there­ fore, vehicles driven under
these
conditions must
be lubricated and serviced more
often
than nor­ mally operated vehicles. The specifications of
types
and
amounts of lubricant given in the Lubrication

Chart
and
text
of this section should be closely
followed. The off-highway operation lubrication
notes,
given in the last part of the section, should
be followed when applicable. 7

B
LUBRICATION D0®
® ® ®

FIG.
B-l—-LUBRICATION CHART
—
4-WHEEL DRIVE
VEHICLES

CHART NO.
ITEM
TO BE

LUBRICATED

10.
11.
13.
14.
Chassis
Bearings. . .

Spring
Shackle and Pivot Bushings...

Universal
Joints Propeller Shaft
Front
Axle
Steering
Gear
Housing

Rear
Wheel BearingstS

Front
Wheel Bearings
<S>.

Transmission:
3
Speed
4 Speed °

Transfer
Case
Differentials
Front.

Rear

Speedometer Cable

Generator
— F4
Distributor
— F4
Oiler
Wick

Pivot.
Gam

Distributor
Cam — V6.

Air
Cleaner — F4
—
V6

Engine
— F4

Engine
— V6.
FREQUENCY

1000 miles — 1.600 km.

Each
2,000
miles

/With
Lube
Fitting;
(Each
2,000
miles [Without
Lube
Fittings:
\No Lubrication

Each
2,000
miles

f
Check
each
2,000
miles

\
Change each
12,000
miles

Check
each
2,000
miles

fWith
Lube
Fittings:

1
Sparingly each
2,000
miles
J
Without
Lube
Fitting:

|
Disassemble to lubricate
\each
12,000
miles
Disassemble to lubricate
each
12,000
miles

I
Check
each
2,000
miles
l
Change each
12,000
miles

/Check
each
2,000
miles
l
Change each
12,000
miles

!Check
each
2,000
miles

\
Change each
12,000
miles

f
Check
each
2,000
miles

\
Change each
12,000
miles
.
Disassemble to lubricate each
12,000
miles

Each
2,000
miles

Each
2,000
miles
Each
2,000
miles

Each
2,000
miles
Each
2,000
miles

At
each breaker point replacement

/Each
2,000
miles

\Each
6,000
miles
Change each
2,000
miles
or 60 days
Change each
6,000
miles
or 60 days
QUANTITY
U.S.
Imperial Metric

As
required
As
required

As
required

As
required
As
required

As
required

As
required

2H
Pts. 2 pts. 1,2 ltrs.
6 H pts. 5
M
pts. 3,2 ltrs.

3Mpti«
3 pts. 1,5 ltrs. 2
M
pts. 2 pts. 1,2 ltrs.
2
Yi
pts. 2 pts. 1,2 ltrs.
As
required

Several
Drops

Several
Drops
One
Drop
One
Drop
2 c.c.

As
required
1 H pts. 1 pt. 0,6 ltrs.
4 qt. m 314 qt. 3,8 ltrs.
4 qt.
11
3 34 qt. 3,8 ltrs.
LUBRICANT

TYPE

Chassis
Lubricant

Chassis
Lubricant

Chassis
Lubricant
GL3

MIL-L-2105-B

Wheel
Bearing
Lubricant

Wheel
Bearing
Lubricant
GL4
GL4 GL4

MIL-L-2105-B

MIL-L-2105-Bttt

Graphite
Grease

Engine
Oil

Engine
Oil

Engine
Oil

Engine
Oil

Cam
Lubricant
Cam
Lubricant

Engine
Oil

Engine
Oil

Engine
Oil
GRADE

No. 1 No.
1
No. 1 No. 1
No. 1

SAE-140
No. 1

SAE-140

SAE-80
No. 2
SAE-

No. 80
2
No. 2 No. 2

SAE-90
SAE
80

SAE-90
SAE
80

SAE-90
SAE
80

SAE-80
SAE-80
SAE
SAE
80
80

Light
Same as
engine

Same as
engine

Same as
engine

Same as
engine

SAE-40
or 50
SAE-20

Above 90
°F.

use SAE 30 or 10W-30
Not lower than
32°F.
[0°C.|

use SAE 20W or SAE 10W-30 Between
-f-10°F.
and 90
8F.

use SAE 20W or 10W-30 Between
-10°F.
and
+10°F.

use SAE 10W or 10W-20 Between
32eF.
[0°C.]
and 0°F.
l-17°Cl

use SAE 10W or SAE 10W-30
*4-Speed transmission and transfer case require separate lubrication of each unit.

tttFor
Powr-Lok
and
Trac-Lok
differential use only 'Jeep* Differential Oil,
Part
No. 94557.
SI
When filter is changed at the same time, add one quart.

®
Do not mix lithium and sodium base lubricants. Use lithium base lubricant as specified Below
-10°F.

use SAE 5W or 5W-20
Below 0°F. [-17°C.J
use SAE 5W or SAE 5W-20 8

*Jeep?
UNIVERSAL
SERIES
SERVICE
MANUAL

FIG.
B-2—LUBRICATION
CHART
—
2-WHEEL
DRIVE
VEHICLES

CHART
NO
ITEM
TO BE

LUBRICATED
FREQUENCY

1000 miles = 1.600 km.
QUANTITY

U.S.
Imperial Metric
LUBRICANT

TYPE
Summer I Winter

Chassis
Bearings.....

Universal
Joints...... Steering
Gear
Housing

Rear
Wheel Bearings fx

Front
Wheel
Bearings®

Transmission

Differential

Hand
Brake Control Handle Cable

Hand
Brake Control
Cable
Rear

Generator — F4

Speedometer
Cable....
Distributor — F4
Oiler

Wick

Pivot
Cam

Distributor Cam — V6.

Air
Cleaner — F4
—
V6.
....

Engine
— F4

Engine
— V6
Each
2,000
miles

Each
2,000
miles

Check
each
2,000
miles

With
Lube Fittings;
Sparingly each
2.000
miles
Without Lube Fittings: Disassemble to Lubricate
each
12,000
miles
Disassemble to lubricate each

12,000
miles

Check
each
2,000
miles
Change each
20,000
miles

Check
each
2,000
miles Change each
12,000
miles

Each
12,000
miles

Each
12,000
miles

Each
2,000
miles Disassemble to lubricate each
12,000
miles

Each
2,000
miles
Each
2,000
miles

Each
2,000
miles

Each
2,000
miles

At
each breaker point replacement
Each
2,000
miles
Each
6,000
miles
Change each
2,000
miles or 60 days Change each
6.000
miles or 60 days
As
required

As
required

As
required

As
required

As
required
1 XA pts. 114 pts. 0,7 ltrs. 2 pts. 1 % pts. 0,9 ltrs.

As
required

As
required
2 to 4 Drops
As
required

Several
Drops One Drop
One Drop
2 c.c.

As
required
1
M
pts. 1 pt. 0,6 ltrs.
4 qt.** 3 H qts. 3,8 ltrs. 4 qt.** 3
}A
qts. 3,8 ltrs.
Chassis
Lubricant

Chassis
Lubricant
MIL-L-2105-B

Wheel Bearing Lubricant
Wheel Bearing Lubricant
GL4

MIL-L-2105-B*

Graphite
Grease

Graphite
Grease
Engine
Oil

Graphite
Grease

Engine
Oil

Engine
Oil

Engine
Oil

Cam
Lubricant

Cam
Lubricant

Engine
Oil

Engine
Oil

Engine
Oil No. 1 No. 1
No. 1 No. 1

SAE-80 SAE-80
No. 2 No. 2
No. 2 No. 2

SAE-90 SAE-80
SAE-80 SAE-80

Medium Medium
Medium Medium Same as
engine
Light

Same as
engine

Same as
engine

Same as
engine

SAE-40
or 50

®
Above
90°F.
Between -f
10°F.
and
90°F.
Between
-10°F.
and
-fl0°F.
Below
-10°F.
use SAE 30 or 10W-30 use SAE 20W or 10W-30 use SAE 10W or 10W-20 use SAE 5W or 5W-20

BE
St
Not lower than
32°F.
[08C] Between
32°F.
10°C] and 0°F.
l-17°CI
Below 0°F. [-17°C] use SAE 20W or SAE 10W-30 use SAE 10W or SAE 10W-30 use SAE 5W or SAE 5W-20

•For
Powr-Lok and
Trac-Lok
differential use only 'Jeep' Differential Oil, Part No.
94557.

**When oil filter is changed at the same time, add one quart {one
ltr.].
(x)Do not mix lithium and sodium
base
lubricants. Use lithium
base
lubricants as specified. 9

B

LUBRICATION
B-2.
Special Lubricants

Special
lubricants are required for certain
lubri­
cation points on the 'Jeep' Universal vehicles. The

special
lubricants are necessary for proper function­ ing and maintenance of the vehicle. The
Lubrica­
tion
Chart
(Fig. B-l and B-2)
designates
the spe­
cial
lubricating points and identifies them by type

or
part number.

B-3.
Applying
Fresh
Lubricant

When
servicing or lubricating the vehicle, it is important that all old lubricant and
dirt
be re­ moved from the fitting and/or plugs before servic­
ing and that the recommended type of lubricant be used for the particular item being serviced.
Force
lubricant through the lube fittings until the lubricant being forced out of the joint is fresh

lubricant,
indicating that all old lubricant has
been removed.

B-4.
Engine
Lubrication
System —
Hurricane
F4 Engine

•
Refer to Fig. B-3.

The
engine
oil pressure system is designed to pro­
vide adequate lubrication to all working parts of
the engine. The gear-type oil pump is driven from
the
engine
camshaft. The pump is provided with a
FIG.
B-3—ENGINE
LUBRICATION
SYSTEM
—

HURRICANE
F4
ENGINE
floating, screened intake that prevents the
circula­

tion of any sediment that might accumulate in the

oil
pan. By means of this pump, the main bearing

journals
and crankpins are efficiently lubricated through an oil gallery and passages in the cylinder
block.
Oil
is forced under pressure to the main bear­
ings and through the cheeks of the crankshaft to
the connecting rod bearings. Oil is also force-fed
to the camshaft bearings, timing gears, and intake valve rocker arms. The oil pressure is controlled by

relief
valve located in the oil pump. The valve is
designed to open when excessive pressure
develops
in
the system, relieving the pressure and returning the
excess
oil to the oil pan. The cylinder walls,
piston pins, and tappets are supplied with oil from
spurt
holes
in the connecting rods. A portion of the oil is continually passed through an oil filter
which
effectively removes any foreign matter sus­ pended in the oil. A flanged section on the
rear
of
the crankshaft acts as an oil slinger and, in com­
bination with the
rear
main bearing upper and lower oil seal, prevents the leakage of oil from the

rear
end of the cylinder block. Leakage of oil from
the front end of the cylinder block is controlled by the crankshaft oil slinger and the front oil seal
installed in the timing gear cover. The oil pressure
indicator
light in the instrument panel and the oil level
gauge
or dip stick in the side of the
engine

provide a means for checking the oil pressure and

oil
level.

B-5.
Oil Pressure Gauge or Indicator
On
early
CJ-3B
vehicles an oil pressure
gauge
is
mounted on the instrument panel.
This
gauge
in­ dicates the oil pressure within the
engine
lubri­

cating system.

On
Models
CJ-5,
CJ-5A,
CJ-6,
CJ-6A,
DJ-5, DJ-6

and
later production vehicles of Model
CJ-3B
a
red
telltale lamp, which operates when the ignition
switch is turned on, is lit when there is insufficient
oil
pressure to properly lubricate the engine. When

it
goes
out, operating pressure is achieved. In
normal
operation, the light is lit when the ignition
is first turned on. It
goes
out after the vehicle is

in
motion.

Failure
of the
gauge
or indicator to register normal
oil
pressure may indicate insufficient supply of oil

in
the
engine
crankcase, low or no oil pump pres­
sure,
or a fault in the
gauge
or indicator electrical

circuit.
The
engine
must be stopped immediately to prevent possible damage to
engine
bearings and
the fault corrected before restarting the engine.

B-6.
Engine
Lubrication
System — Dauntless V-6 Engine

The
engine
lubrication system (Fig. B-4) is the
force
feed
type in which oil is supplied under pres­

sure
to the crankshaft, connecting rods, camshaft bearings and valve lifters. Oil is supplied under con­trolled volume to the rocker arm bearings and push

rods.
All other moving parts are lubricated by gravity flow or splash.

The
supply of oil is
carried
in the oil pan which is filled through a filter opening in the right rocker

arm
cover. A removable oil
gauge
rod on the left side of the crankcase is provided to check oil level.

The
oil pump is located in the timing chain cover 10

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

13330

FIG.
B-4—ENGINE
LUBRICATION
SYSTEM
—
DAUNTLESS
V-6
ENGINE

1—
Rocker
Arm Shaft
2—
Main
Oil
Line

3—
Oil
Inlet where it is connected by a drilled passage in the

cylinder
crankcase to an oil screen housing and
pipe assembly. The screen is submerged in the oil supply and has ample area for all operating condi­
tions. If the screen should
become
clogged
for any reason, oil may be drawn into the system over the
top
edge
of the screen, which is held clear of the

sheet
metal screen housing.

Oil
is drawn into the pump through the screen and
pipe assembly and a drilled passage in the
crank­

case, which connects to drilled passages in the
timing chain cover. All oil is discharged from the
pump to the oil pump cover assembly. The cover
assembly consists of an oil pressure relief valve,
an
oil filter bypass valve and a nipple for installa­
tion of an oil filter. The spring loaded oil pressure

relief
valve limits the oil pressure to a maximum
of 30 pounds [13.607 kg.] per square inch. The

oil
filter bypass valve
opens
when the filter has
become
clogged
to the
extent
that
4V2
to 5 pounds [2.04 a 2.27 kg.] pressure difference exists
between

the filter inlet and exhaust to bypass the oil filter
and
channel unfiltered oil directly to the main oil galleries of the engine.

A
full flow oil filter is externally mounted to the

oil
filter cover nipple on the right side of the en­ gine, just below the alternator. Normally, all
engine

oil
passes through the filter element; however, if
the element
becomes
restricted, a spring loaded bypass valve
opens
as mentioned above. The main

oil
galleries run the full length of the crankcase
and
cut into the valve lifter guide
holes
to supply

oil
at full pressure to the lifters. Connecting pas­
sages
drilled in the crankcase permit delivery of

oil
at full pressure to all crankshaft and camshaft
bearings.
Holes drilled in the crankshaft
carry
oil from the
crankshaft
bearings to the connecting rod bearings.
Pistons and cylinder walls are lubricated by oil
forced through a small notch in the bearing parting
surface on the connecting rod, which registers with
the
hole
in the crankpin
once
in every revolution. Piston pins are lubricated by splash.

Drilled
holes
in the camshaft connect the front camshaft bearing
journal
to the key slot in the front
of the camshaft. Oil flows from the
journal
into
the keyslot over the woodruff key in the space

between
the key and the camshaft sprocket and fuel pump eccentric.

The
forward end of the fuel pump eccentric in­ corporates a relief which allows the oil to escape

between
the fuel pump eccentric and the camshaft

distributor
gear. The oil stream strikes the distri­
butor shaft gear
once
each camshaft revolution, and provides ample lubrication of the timing chain and
sprockets by splash.

The
rocker arms and valves on each cylinder head

are
supplied with oil from the oil galleries through

holes
drilled in the front of the cylinder block and

cylinder
head. The
hole
drilled in the cylinder
head ends beneath the front rocker
arm
shaft brack­ et. A notch cast in the base of the rocker arm shaft

bracket
allows the oil to flow up inside the bracket

in
the space
between
the bracket and bolt, to the
hollow rocker arm shaft which is plugged at both
ends.
Each
rocker arm receives oil through a
hole

in
the underside of the shaft. Grooves in the rocker

arm
provide lubrication of the bearing surface. Oil
is metered to the push rod seat and valve stem
through
holes
drilled in the rocker arm. Excess
oil
drains off and returns to the oil pan through
passages in the cylinder head and block. Refer to
the
Lubrication
Chart
for lubrication frequency and

lubrication
type and grade.

B-7.
Chassis
Lubrication

Chassis
and
engine
should be serviced at periodic
intervals.
Most chassis lubricating points, whether
long-life or conventional, have standard lubrication
fittings. Refer to the
Lubrication
Specifications and

Service
Maintenance Schedule for specific points

and
lubricating time intervals. It is not necessary
to disassemble prepacked joints to lubricate them.

Merely
add new lubricant, as described in Par.
B-3,
to remove all old lubricant.

At
the appropriate interval, clean each lubrication
fitting indicated on the Lubrication
Chart
and
Service
Maintenance Schedule. Use a pressure gun
to lubricate. Be sure the grease channels are open
to provide complete lubrication of bearing surfaces.
In
some
cases it may be necessary to disassemble
to clear plugged channels.

When
vehicles are driven primarily in abnormally dusty or wet areas or when a vehicle is subject to
severe operating conditions, perform
these
services
more frequently. Under
these
conditions, no definite interval can be recommended because of the great variety of
uses
and conditions of use. 11

B
LUBRICATION B-3.
SERVICE
MAINTENANCE
SCHEDULE

Perform
the following operations at the mileage shown. Two thousand miles equals
3,200
km.

SERVICE
MAINTENANCE
SCHEDULE

OPERATION
VEHICLE
^ n>
MILEAGE
IN
THOUSANDS

6 8 10 12 24 30
Check Wheel Nut Torque*
Check
Fluid
Level
in Battery X Check
Fluid
Level
in Brake Master Cylinder0. X
Service
Cooling
System X Service Tires X

Lubricate
Distributor
Cam Lubricator (F4-134) X
Lubricate
Steering Linkage X

Lubricate
Propeller Shaft Universal Joints X

Lubricate
Propeller Shaft
Slip
Joints ; X
Lubricate
Tie Rod and Drag
Link
Sockets................................... X Change Engine
Oil
and
Filter,
and Service Air Cleaner (F4 134 Engine)** X
Change Engine Oil and
Filter,
and Service Air Cleaner (V6-225 Engine)**....
Check Brake Operation and Pedal
Free
Play X Check
Clutch
Pedal
Free
Play. .... X
Check all
V-Belt
Tensions X
Check Exhaust Emission System
(If
so equipped)*** \ X
Service Positive
Crankcase
Vent
Valve
and Breather . .' X
Road Test
Including
a Check of all Instrument
Lights
and Controls X Tune-up Engine
Check Operation of
Manifold
Heat
Control
Valve

Clean
Exterior of Radiator

Align
Headlights • Check Brake
Linings
,
Check Exhaust System for Leaks Replace Canister Air
Filter
(F. E. E. C. System)
Check
Axle
U-Bolt
Torque. Check Lubricaunt
Level
of Front
Axle
Universal Joints
Check Shock Absorber Mountings and Bushings Check Front and
Rear
Spring Bushings

Lubricate
Distributor
(V6-225).
Replace Spark, Plugs
Check Charging and Starting Circuits
Lubricate
Tailgate Latch, Supports and Hinges.

Lubricate
Door and
Hood
Hinge Pivots ;
Lubricate
Glove Compartment Door Latch

Lubricate
Heater Controls •

Lubricate
Windshield
Wiper and Washer Controls
Clean,
Repack and
Adjust
Wheel Bearings
Change Transmission and Transfer Lubricant. .
Replace
Dry-Type
Air Cleaner • Check Lubricant
Level
of
Differential

Lubricate
Transfer
Case
Shift
LeArer
Control
C«se.
. , . . . . . . . .
Continuing
each
2,000 miles

Continuing
each
6,000 miles

Continuing
each
24,000 miles

X
Continuing
each
30,000 miles
•Check after the
first
200 miles [320
km.
J
of operation.
If
wheel or wheels are changed for any
reason,
have
wheel nut torque rechecked after an additional two hundred miles of operation
••Service mileage shown or every 60 days, whichever occurs
first.

•••Maintenance check on emission system must be performed per
information
in this manual. "See text for brakes.

"Nj
^Miles
2,000
6,000
12,000
18,000
24,000
30,000
Kilometers

3,200
9,600
19,200
28,800
38,400 48,000

B-9.
Engine Oil

For
maximum
engine
protection under all driving conditions encountered during the recommended

oil
change intervals, it is necessary to use only

"MS"
certified
sequence-tested
oils. The term
"MS"
must appear on the oil container singly or

in
conjunction with other designations. "MS" des­
ignated oils are heavy-duty detergent oils that are
formulated to withstand all service conditions in
modern powerplants. Engine oils designated only
as
"ML"
and/or
"MM"
are not recommended and should not be used except in an emergency when

"MS"
oil is not available. Certified
sequence-tested

engine
oils are described on their containers by

such
phrases as:
meets,
exceeds,
excels, or has
proven superior in the
test
requirements,
test
sequences, MS Service
tests,
standards, and service

requirements,
of automotive manufacturers, auto­
makers,
or car manufacturers for MS service or
Service
MS.
It
may be necessary to change
engine
oil more
frequently than normally recommended, depending upon the type and quality of oil used, the severity
of operation conditions, if the
engine
is used for
short
periods in cold weather, or if the
engine
is allowed to idle for excessive periods.

Always
drain
the crankcase while the
engine
is hot since
dirt
and contaminants are then more
likely
to be held in suspension and therefore
will

drain
out more completely.
Drain
the crankcase as follows:

a.
Position the
drain
receptacle under the
drain

plug.

b.
Remove the
drain
plug using the correct size

wrench.
Be careful of hot oil.
c.
Carefully
clean the
drain
plug. Inspect and

replace
the gasket, if deteriorated.
d.
When the oil has drained, replace and tighten
the crankcase
drain
plug. 12

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

B
e.
Check
for the presence of
excess
water in the

oil
that might indicate an internal leak from the
cooling system.

f.
Pour oil into the oil filler tube. Replace the oil

filler
cap.

B-10.
Engine Oil
Filter
Service —
Hurricane
F4 Engine

The
engine
oil filter assembly should be replaced at each
2000
miles
[3.200
km.] of normal
engine

use. To remove the filter, use oil filter wrench
C-4065.
To install a new filter, wipe the gasket —
contact surface with
engine
oil, screw on the unit

until
gasket contacts the sealing surface, and then tighten at least one
half
turn
more. DO NOT USE

TOOLS.
Turn
by hand only. When refilling the
engine
crankcase after filter has been changed be

sure
to add one extra quart [1 ltr.] of oil to
fill

filter
and oil passages. Run
engine
to make sure there is no leak at oil filter.

B-l 1.
Engine Oil
Filter
Service — Dauntless V-6 Engine

To
replace the oil filter, use oil filter wrench, Tool

C-4065,
to remove the filter. After the filter has
been removed from the oil pump housing located
on the right front side of the engine, wipe the
housing surface clean and oil the gasket on the base of the new filter to make a
good
seal. Screw
the new filter in position until its gasket contacts
the pump housing surface, then tighten at least
one-half
turn
until filter fits snug.

Note:
Tighten by hand only, do not use a tool to
tighten.

Replace
oil filter each
6000
miles
[9.600
km.] at

engine
oil change.

B-12.
Exhaust
Manifold
Heat
Control
Valve
— Dauntless V-6 Engine

A
thermally-actuated heat control valve is located at
rear
of the right exhaust manifold of the Daunt­

less
V-6 engine.
This
valve has a bimetal thermo­
static spring which holds the valve closed when
the
engine
is cold.

Each
time the vehicle is lubricated place a few drops of penetrating oil on the valve shaft bushings

and
then work the valve by hand making sure that
the lubricant is worked into the bushings.

Note:
If the valve shaft
does
not operate freely
penetrating oil should be used to free the shaft.

B-l 3.
Positive
Crankcase
Ventilation
System

Service
the ventilation system of the
engine
each
multiple of
6000
miles
[9.600
km.] on the odometer
after
initial
2000
miles
[3.200
km.] service. Re­
place the ventilation valve each
12,000
miles
[19.200
km.].

For
information on servicing the positive crankcase
ventilation system on the
Hurricane
F4
engine
and
the Dauntless V-6 engine, refer to the Tune-up Section.

B-l4.
Distributor
— Hurricane F4 Engine

The
distributor shaft is lubricated through an oiler mounted on the side of the housing. Place three or four drops of light
engine
oil in the oiler each
2,000

miles
[3.200
km.]. Also place one drop of light
engine
oil on the wick located on the top of the
shaft, which is made accessible by removing the
rotor
arm. Sparingly apply cam lubricant to the
breaker
arm cam and place a drop of oil on the

breaker
arm pivot.

B-l
5.
Distributor
— Dauntless V-6 Engine

The
distributor has a lubricant reservoir that
car­

ries
sufficient
lubricant
for the life of the distributor.
When
servicing breaker points, place one drop of
light
engine
oil on the wick located on the top of the shaft Also, apply cam lubricant sparingly to
the breaker arm cam, and place a drop of oil on the

breaker
arm pivot.

B-l6.
Generator

On
early production vehicles oilers are provided
at each end of the generator, for lubrication
pur­

pose.
On late production vehicles one oiler is pro­
vided at the
rear
(bushing end) of the generator for lubrication purpose. Place two to four drops of
light
engine
oil in each oiler every
2,000
miles
[3.200
km.].

B-l
7. Spark Plugs

Replace
spark
plugs. Refer to Section C.

B-18.
Starting
Circuit

Check
the starting
circuit.
Refer to Section H.

B-l
9. Charging
Circuit

Check
the charging
circuit.
Refer to Section H.

B-20.
Engine Tune-Up

Refer
to Section C of this manual.

B-21.
Adjust
Fan
Belt

Refer
to Section C.

B-22.
Exhaust Emission
Control
System or
Controlled
Combustion System

•
Refer to the appropriate section in this manual.

B-23.
Exhaust System

Check
the exhaust system for leaks. Refer to Section F.

B-24.
Fuel Evaporative Emission
Control
Canister Air
Filter

The
only service required for the
F.E.E.C.
system
is cleaning the air cleaner filter mounted at the
bottom
of the canister. The filter requires replace­
ment at
12,000
mile intervals. Refer to Section

E,
Par. E-9 for service procedure.

B-25.
Oil Bath Air Cleaner
Some 'Jeep' Universal vehicles are equipped with

an
oil bath type air cleaner.
This
type air cleaner
thoroughly removes all dust from the air before it enters the carburetor, if it is properly serviced.

When
the vehicle is operated under normal condi­
tions the air cleaner must be serviced at regular

intervals
as care of the air cleaner is extremely 13

LUBRICATION

vital
to the life of the
engine.
When the vehicle
is operated under abnormal conditions, (for ex­
ample when driven on secondary roads or through
fields) then service of the air cleaner must be more frequent

Note:
Under extreme continually dusty and dirty
conditions where the vehicle operates in clouds of dust and
dirt,
service the air cleaner daily.

a.
To service the air cleaner on vehicles equipped
with the
Hurricane
F4
engine
(Fig. B-5) unscrew
the eye
bolt
on the oil cup clamp and remove the

oil
cup from the cleaner body. Remove the oil from the cup and scrape all
dirt
from the inside, wash cup clean using a cleaning solution if neces­

sary.
In summer
refill
the oil cup with IV2 pints [0,6 ltrs.] of
SAE-40
or 50 grade
engine
oil. In
winter
refill
using grade
SAE-20
engine
oil. For
servicing the air cleaner
body
(less
oil cup),
loosen

hose
clamp and remove
hose
from the cleaner. Detach breather
hose
from the fitting on the cleaner. Remove the two wing screws and lift the
cleaner from the vehicle. Agitate the cleaner
body

thoroughly in cleaning solution to clean the filtering

element.
Dry
element
with low pressure com­ pressed air. Reinstall the cleaner
body
and replace
the oil cup. Service the air cleaner every
2000
miles
[3.200
km.].
b. To service the oil bath air cleaner on vehicle
equipped with the Dauntless V-6
engine
(Fig. B-6),

first
remove the air cleaner from the carburetor
by unscrewing the wing nut. Remove the oil cup
FIG.
B-5—OIL
BATH AIR
CLEANER
-
HURRICANE F4 ENGINE 1—
Horn
7—Clamp
2—
Flexible
Connector
8—Oil
Cup
3—
Hon
Clamp
9—Clamp

A—Carburetor
Vent Tube 10—Hose 5— Body 11—Clamp
6—
Screw
and
Lock
Washer 13—Gasket
FIG.

B-6—OIL BATH AIR
CLEANER
-
DAUNTLESS V-6 ENGINE

1—WinB
Nut
2—
Cover

3—
Rubber
Gasket
4—
Cork
Gasket
5—
Oil
Cup 6—
Breather

7—
Clamp

8—
Vent
Tube 9—
Air
Pump Hose from cleaner
body
and remove the oil from the cup,
scrape all
dirt
from the inside.
Clean
oil cup thor­
oughly, wash filter
element
in a solvent that
will
leave it clean and dry.
Fill
oil cup to indicated
level with clean
S.A.E.
40 or 50 grade
engine
oil
(S.A.E.
20 grade in winter.) Assemble cleaner filter

element
to oil cup making sure that gasket is in
place
between
the two pieces. Assemble air cleaner assembly to carburetor making sure the gasket
be­

tween
air cleaner and carburetor is in place. Secure

air
cleaner to carburetor with wing nut. Service the

air
cleaner every
6000
miles
[9.600
km.],
c.
Carefully
check the
hose
clamps and
fittings
on
the breather
hoses
at frequent intervals. Loose con­nections
will
affect proper operation of the
crank­

case ventilating system.

B-26. Dry-Type
Air Cleaner Service the air cleaner on Dauntless V-6
engines

at each oil change under normal driving conditions.

If
the vehicle is operated under dusty conditions,
check the condition of the air cleaner
element
more
frequently and service if dirty.

Servicing
the air cleaner consists of cleaning or replacing the air cleaner
element
and replacing the

crankcase
ventilation filter (breather assembly). See Fig. B-7.

The
air cleaner
element
assembly consists of a
paper
element
and a polyurethane
element
The
paper
element
cannot be cleaned.

To
clean the polyurethane
element,
first carefullly remove it from the paper
element
Then
wash it in 14

'Jeep*
UNIVERSAL SERIES SERVICE
MANUAL

B
solvent.
Wrap
the polyurethane element in a clean

dry
cloth and
squeeze
to remove all possible sol­
vent. Do not wring the element or it may
become
torn.
After cleaning, oil the polyurethane element

liberally
with
engine
oil
(SAE
10W30) and
squeeze

to evenly distribute the oil through the element and to remove
excess
oil. The element should be damp

with
oil, not dripping.
Install
the polyurethane element on the paper element, taking care to have
edges
of the polyurethane element over the plastic end plates of the paper element.

Replace
the complete air cleaner element assembly every
24,000
miles
[38.400
km.]. Replace more
frequently if there is any apparent damage or evidence of plugging.

The
crankcase ventilation filter should be replaced, not cleaned, every
6,000
miles
[9.600
km.]. The
filter
is located inside the air cleaner housing.
12992

FIG.
B-7—DRY-TYPE
AIR
CLEANER DAUNTLESS
V-6
ENGINE

1—
Crankcase
Ventilation
Filter

2—
Polyurethane
Element

3—
Paper
Element
B-27.
Steering
Gear

Check
that the steering gear lubricant is at the
level of the fill-hole. If not, add lubricant to the
level of the fill-hole with the lubricant recom­ mended in the
Lubrication
Specifications. If abnor­

mally
low, check the steering gear for possibility
of leaks.

B-28.
Cooling System
Check
the coolant level in the
radiator.
It should be

half
an inch below the neck. If not,
fill
the radiator
to
half
inch below the neck with the proper coolant.

Refer
to Section G.

If
the level of the coolant is abnormally low, check
the radiator,
hoses
and water pump for possible
leaks.
If a leak is suspected, refer to Section G.

B-29.
Clean
Exterior
of Radiator

For
proper cooling efficiency the radiator should be cleaned of foreign objects. Refer to Section G.

B-30.
Transmission
and
Transfer Case
Lubricant
Level
Cheek

•
Refer to Par. B-31 through B-33 as applicable.
B-31.
General

All
transfer cases and transmissions should be

serviced
separately even though drilled passages
are
provided for oil circulation
between
some
trans­
mission and the transfer case housings. Procedure

from
the appropriate Par. below should be fol­ lowed to check the lubricant level of the various

types
of transfer cases and transmissions.
If
the transfer case or transmission fluid levels
are
found to be abnormally low, check both units
for any possible leaks.

B-32.
Transfer
Case
:

The
transfer case fill-hole is located on the right side of the transfer case housing. To check the
lubricant
level, remove the
fill
plug.
Lubricant

should be level with this fill-hole. If not, bring up to level by adding make-up lubricant as specified

in
the
Lubrication
Specifications.

B-33.
Transmission

The
transmission fill-hole is located on the right side of the transmission housing. To check the
lubricant
level, remove the
fill
plug.
Lubricant

should be level with this fill-hole. If not, bring
up to level by adding make-up
lubricant
as specified
in
the
Lubrication
Specifications.

B-34.
Transmission and Transfer
Case
Lubricant
Change

•
Refer to Par. B-35 through B-37 as applicable.

B-35.
General

Transfer
case and transmission lubricants should
be changed at the same time.

B-36.
Transfer
Case

To
drain
the transfer case, first remove the transfer
case fill-hole plug and then the transfer case
drain-

hole
plug. Let all fluid
drain
from case.
Then
install
the transfer case drainhole plug, and
refill
the
transfer
case through the fill-hole using the correct

lubricant
as specified in the
Lubrication
Specifica­
tions.

At
30,000
mile
[48,000
km.] intervals lube the

transfer
case shift levers with
Lubriplate
No.
130AA.
Late
models have a lube fitting. To lube
older models, (without lube fitting) remove the

bottom
cover of the case, clean thoroughly and
pack
case
full
of lubricant.

B-37.
Transmission (3-Speed)

To
change the lubricant on all vehicles equipped

with
a three speed synchromesh transmission,
drain

the old fluid by first removing the fill-hole plug

and
then removing the drainhole plug. Since on

some
transmissions there are drilled passages be­ tween the transmission and transfer case that allow

oil
to circulate
between
the two units, the transfer
case should be drained before refilling the trans­

mission.

When
all the fluid is completely drained, replace
the drainhole plugs only. For the correct specifi­
cations and quantity, refer to the
Lubrication
Specifications. 15

B

LUBRICATION
B-72.
Powr-Lok
or Trac-Lok
Differential

Refer
to Par. B-53.

B-73.
PARTS
REQUIRING
NO
LUBRICATION

B-74.
Water Pump Bearing,
Clutch
Release
Bearing

The
water pump and clutch release bearings are

prelubricated
for life when manufactured and cannot be relubricated.

B-7S.
Starter
Motor
Bearings

The
starting motor bearings are lubricated at assembly to last
between
normal rebuild periods.

B-76.
Alternator Bearings

The
alternator bearings are lubricated at assembly

and
require no further lubrication.

B-77.
Springs

The
vehicle springs should not be lubricated. At assembly the leaves are coated with a long-lasting

special
lubricant which is designed to last the life
of the springs. Spraying with the usual mixture of
oil
and kerosene has a tendency to wash this
lubri­

cant
from
between
the leaves, making it necessary
to relubricate
often
to eliminate squeaking.

B-78.
Shock Absorbers

Hydraulic
direct-action shock absorbers are per­ manently sealed and require no periodic
lubrica­

tion service. Shock absorber mounting bushings
are
not to be lubricated.

B-79.
LUBRICATION
REQUIREMENTS
FOR
OFF-HIGHWAY
OPERATION

Adequate lubrication
becomes
increasingly im­ portant when vehicles are used in off-highway
operation. Under
these
conditions all operating
parts
of both the
engine
and chassis are subjected
to unusual pressures. At the same time such operation is usually under abnormal dust and
dirt

conditions making additional precautions neces­

sary.
The importance of correct lubrication for
the conditions of operation cannot be overestimated.

B-80.
Engine
Oil

It
is important, that the oil in a new or rebuilt
engine
be changed after the first
eight
or ten hours
of operation, and for heavy, dusty work, every 50

hours
thereafter. Watch the condition of the oil closely and change it immediately if it appears to
be contaminated.

i-Il.
Engine
Oil
Filter

Replace
the oil filter at the end of the first 100

hours
of service. Under extreme operating con­ ditions, more frequent replacement may be re­
quired.
The condition of the oil is a reliable

indicator
of the condition of the filter element.
If
the oil
becomes
discolored and shows evidence
of contamination, change the filter without delay.
(Refer
to
Par.
B-10, B-ll for the correct procedure
for replacing the oil filter.)

B-82.
Air Cleaner

Care
of the air cleaner is extremely vital to the life of the engine. Pay particular attention to the
amount of dust and
dirt
in the air taken into the

engine
through the air cleaner. When dust is not
noticeable in the air, service the air cleaner each scheduled maintenance period. Whenever the air is
noticeably dusty (for example when the vehicle is

driven
on secondary roads or through fields) then
service the air cleaner more frequently. Under extreme continually dusty and dirty conditions
where the vehicle operates in clouds of dust and

dirt,
service the air cleaner daily. (Refer to Par.
B-24
thru
B-26 for service procedures.)

B-83.
Chassis
Lubrication

The
period of lubrication depends entirely upon the type of work being done. Using the specified

interval
given in the Service Maintenance Schedule as a guide, lubricate at safe intervals required for
the particular type of operation. Under extremely
dusty conditions lubricate
these
points daily. Be

sure
to force enough lubricant into each fitting to force out the old lubricant which might be con­
taminated with grit and which would cause
rapid

wear
if allowed to remain.
Do not place lubricant on the various
ball
and socket joints or pivot points of the lift linkage as
dirt
will
accumulate to form an abrasive mix­

ture.
It is
best
to simply wipe
these
parts clean

with
a cloth.

B-84.
Front
Axle
Shaft Universal Joints

For
off-highway use remove the universal joints twice yearly, thoroughly clean both the housings

and
joints with a suitable solvent, and
refill
the
housings to the
fill
plug opening levels with the

correct
lubricant as given in the
Lubrication
Specifications.

B-85.
Transmission and Transfer
Case

The
combined capacity of the two housings is
small
for economy, making it important that the

lubricant
be changed at regular intervals. For off-highway use
drain
both housings every 300

hours
of operation and
refill
to the
fill
plug opening
levels. Refer to B-35 through B-37 when changing

lubricant.

B-86.
Front and
Rear
Axle
Differentials

Because of the higher pressure developed in the
axle assemblies with heavy duty operation,
drain,

flush,
and
refill
the differential assemblies each 300 hours of operation. Use only flushing oil or light
engine
oil to clean out the housings (except

Powr-Lok
and
Trac-Lok
differentials). Refer to
Par.
B-52 and B-53 for draining and flushing

differential.
18