ECU JEEP DJ 1953 Workshop Manual

ELECTRICALJ
SYSTEM

d.
Inspect for
excessive
wear
between
centrifugal

weights
and advance cam and pivot pins.
Turn
weight
base plate in a clockwise direction until
weights
are fully extended. Release and allow
springs to return
weights
to
retard
position. Repeat several times. Springs should return
weights
to
stop
without sticking and there should be no
excessive
free
movement
in the
retard
position. Inspect
springs for distortion and fatigue.
e. Inspect cam
lobes
for scoring or
excessive
wear.
Check
weight
base plate for binding or
excessive

looseness
on distributor shaft.

f.
Check
breaker plate for
excessive
looseness
on
outside
diameter of upper distributor shaft bushing.
Check
breaker plate ground lead for poor
spot
we
Id

at plate end and for
loose
or frayed terminal con­
nections.
g.
Check
for
excessive
wear
between
distributor
shaft and bushings in housing. Inspect shaft for distortion. Inspect gear for scoring of
teeth
or

excessive
wear.

h.
Inspect rod end of vacuum advance mechanism
for
excessive
wear. Push rod
into
unit as far as
possible, hold finger tightly over nipple, then re­
lease
rod. After about 15 seconds, remove finger
from nipple, and
notice
if air is drawn
into
unit.
If
not, diaphragm is leaking and unit must be
replaced.

H-29.
Distributor Reassembly

Refer
to Fig. H-l5.

a.
Install
distributor
primary
lead and rubber grommet in distributor housing. Mount vacuum
advance unit on housing with two
slotted
attaching
screws; insert ground lead terminal of breaker plate under outer mounting screw.
b.
Install
felt
washer over upper shaft bushing of
distributor housing and apply a few drops of light

oil.
Secure breaker plate to upper bushing with re­ tainer. See Fig. H-17.
12767

FIG.
H-17—INSTALLING
BREAKER
PLATE
ON
DISTRIBUTOR
HOUSING
(DELCO)

1—
Breaker
Plate
2—
Retainer

3—
Retainer
Groove
4—
Lubricant
Reservoir c.
Install
distributor cam and
weight
base plate
on distributor shaft.

d.
Insert distributor shaft
into
distributor housing.
Install
centrifugal advance
weights
and springs on

cam
and
weight
base plate. e. Fasten driven gear to shaft with pin. Be care­
ful
not to damage gear.

f.
Secure condenser and bracket to breaker plate
with
slotted
screw.
g.
Install
breaker point assembly over
boss
on
breaker
plate; secure with two
slotted
screws and
lock washers. Apply one drop of light oil to breaker

arm
pivot. Connect condenser and coil
primary

leads to breaker point assembly.

h.
Apply a small amount of high temperature cam

and
ball
bearing lubricant to a clean cloth; hold cloth against distributor cam while turning
distri­
butor shaft.

Caution:
Do not apply
excessive
grease. Petro­
leum jelly is not suitable as a distributor cam
lubri­
cant.

i.
Make preliminary adjustment of breaker point
gap, as described in Par. C-10.

].
Secure rotor to centrifugal timing advance mech­
anism with two screws, lock washers, and flat
washers.

Note:
The square and round
lugs
on the rotor must
be positioned in the corresponding
holes
in the

weight
base plate.
k. If a reliable distributor tester is available, check
the distributor to make certain that the centrifugal

and
vacuum advance mechanisms are operating
according to specifications.

Note:
Mount distributor in tester with all end play
of the distributor shaft in upward position; this

will
eliminate any possible drag
between
the centri­ fugal advance cam and
weight
base plate.

I.
Install
new
O-ring
seal on distributor housing.

H-30.
Distributor
Installation
and
Timing

a.
Insert distributor shaft
into
timing gear cover
of
engine
so that rotor is pointing to
mark
made on distributor base (Fig. H-14), with vacuum advance
unit pointing in exact, original direction (Fig.

H-18).

b.
Install
distributor clamp and
bolt
with lock
washer, leaving
bolt
just
loose
enough
to permit
movement
of the distributor with heavy hand
pressure.

C.
Connect
primary
wire to distributor side of coil.
Install
distributor cap on distributor housing. Press

screwdriver
into
upper
slotted
ends
of two cap
retainers.
Turn
retainers clockwise to secure cap to distributor.

d.
If
spark
cables were disconnected from
distri­

butor cap, connect them. Wires must be pushed

all
the way down
into
the distributor cap terminals
and
onto
the
spark
plugs. Nipples must be pushed
firmly
over the terminals;
boots
must be pushed

firmly
over the
spark
plugs. 186

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

H

U029p 1—
Oil
Retainer

2—
Bearing

3—
-Felt
Wick
4—
Oiler

5—
Commutator
End Head
6—
Brush
Lead
Screw
7—
Lockwasher

8—
Brush
Set
9—
Brush
Spring

10—
Brush
Arm

11—
Frame

12—
Insulating
Bushing

13—
Washer

14—
Lockwasher

15—
Hex
Nut
16—
Lockwasher
FIG.
H-20—GENERATOR

17—
Hex
Nut
18—
Ground
Screw
19—
Lockwasher

20—
Hex
Nut

21
—Lockwasher

22—
Hex
Nut

23—
Lockwasher

24—
Washer
25—
Insulating
Washer
26—
Insulating
Bushing
27—
Stud

28—
Left
and Right
Field
Coil

29— Pole Shoes
30— Pole Shoe Screw

31—
Drive
Pulley and Fan Assembly
3
2—Lockwasher
33—
Shaft
Nut
34—
Drive
End Head

35—
Felt
Washer
36—
Felt
Washer Retainer
37—
Ball
Bearing
38—
Gasket

39—
Bearing
Retainer
40—
Lockwasher

41—
Retainer
Screw

42—
-Felt
Washer

43—
Woodruff
Key
44—
Armature

45—
Thru
Bolt
4
6—Lockwasher

with
instructions furnished with the testing equip­ ment.

H-38.
Field
Coils
Inspect the field coils for chafed wires and using

test
lamp prods check for both open and grounded

circuits.
To
test
for open coil, connect the prods
to the two leads from each coil. If the lamp fails
to light, the coil is open and must be repaired or

replaced.

To
test
for ground, place one prod on ground and
the other on the field coil terminal. If a ground is present the lamp
will
light and the coil must be

repaired
or replaced.
If
accurate
test
equipment is available, check the
field coils for current draw which should be with­
in
the limits of 1.2 to 1.3 amperes at 10 volts for both coils.
A shorted coil
will
of course show a much higher
draw,
while an open coil
will
show no draw. In
either case the generator output
will
be below
normal.

To
replace a field coil, disconnect the field termin­

als,
use a heavy screwdriver to remove the field

pole
piece screws, then the coils
together
with the

pole
pieces may be removed. When replacing the coils, set the
pole
piece screws by staking with a
center punch.

H-39.
Brush
Holders

With
test
prods check the insulated brush holder
to be sure it is not grounded. Touch the brush
holder with one prod and the frame with the other prod. If the lamp lights, a grounded brush holder is indicated.
Inspect the brush holders for
cracks,
distortion and

improper
alignment. The brushes should slide freely

and
should be in perfect alignment with the com­ mutator
segments.

H-40.
Assembling Generator

Install
the felt grease retainer and washer in the

drive
end head. See Fig. H-20.
Check
the bearing to be sure it is clean and
fill
it one-half full with

a
high melting point grease.
Install
the bearing
and
also install the inside felt washer and attach
the bearing retainer with the lockwashers and

screws.
Place the drive end head over the front end
of the armature shaft.
Install
the Woodruff key in the armature shaft and install the drive pulley,
being sure the key is in position. Secure in position

with
the washer and nut. Place the assembly on 189

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

H
Resistance
should be approximately 0.1 ohm.

An
extremely accurate instrument would be neces­
sary
to ascertain shorted turns.
Only
an open condi­
tion can be detected with a commercial ohmmeter.

If
the alternator has been disassembled because of
an
electrical malfunction, replace stator only after

all
components have been checked and found to
be satisfactory.

H-85.
Out-Of-Circuit
Rectifier Diode Test

With
the rectifier diode heat sinks disconnected
from
the stator assembly (Par. H-80), the diodes

can
be individually checked with the Diode Tester

C-3829.
FIG.
H-36—RECTIFIER
DIODE
TEST
POINTS

1— Diode Plate Stud

2—
Diode Terminals

Fig.
H-36 shows the
test
point location for either positive or negative diode.

Plug
Tester C-3829 into a 110-volt AC outlet.
Connect
alligator clip to diode plate stud, and the probe of the tester to each of the three diode ter­

minal's
test
points. Negative diodes
will
give a
negative deflection of the needle and positive
diodes
will
give a positive deflection. The meter

reading
should be the same for each of the diodes

and
should be 2 or over for a
good
diode. If a diode is faulty, replace the entire diode heat sink
assembly. H-86.
Assembling Alternator

Refer
to Fig. H-31.

a.
To install front bearing in front housing, press
the bearing into place on an arbor press using

Bearing
Installer C-3858. Position the split spring

washer
in the front bearing housing oh top of the bearing.

b.
Install
the
rear
bearing on the rotor shaft front
end using Bearing Installer C-3935 as shown in

Fig.
H-37.
FIG.
H-37—INSTALLING
REAR
ROTOR
BEARING

1—
Rear
Bearing Installer C-3935

2—
Rotor
Shaft
C.
Place the rotor assembly
into
position in the
front housing by tapping rotor shaft on a
soft

wood surface.

d.
Position diode assemblies and stator as a unit
into the
rear
housing. Make certain that insulator
washers and insulator
sleeves
are correctly posi­
tioned on the positive diode assembly.

e.
To assemble the subassembly halves of the
alternator
(front
housing and
rear
housing). Slide
the front housing over the stator.
Install
the bolts
and
nuts.
f. Position first the spacer, then the woodruff key
on the rotor shaft and slide on the fan.
Carefully

position the alternator in a vise with the clamps
of the vise held to the pulley. Position the pulley
so it is just starting to slide over the woodruff

key.
Press it into position by tightening nut with

a
wrench. When the pulley is properly positioned,
remove the nut, place the lock washer on the

rotor
shaft, and again replace the nut.

g.
Install
the isolation diode assembly and secure

with
locknuts.

h.
Install
the brush housing in position in the
rear

housing.
Install
the brush housing cover and the
tapping screws.

i.
Turn
the rotor by hand listening carefully to

make
certain there is no interference between the

rotor
and the stator winding.
H-87.
Alternator Installation

To
install the alternator, reverse the procedure 201

H

ELECTRICAL
SYSTEM
FIG.
H-38—WIRE
COLOR CODE
AND

LOCATIONS
FOR
ALTERNATOR HOOK-UP

1— Regulator (Auxiliary)
Terminal
(Cable —
Grey)

2— Output
Terminal:
(Red)

3—
Regulator
Terminal
(Cable —
Grey)

4—
Ground
Terminal
(Cable — Black-White
Tracer)
5—
Field
Terminal
(Cable — Green-White
Tracer)

6—
Ground
(Optional)
Terminal
(Cable — Black-White
Tracer)
REAR
VIEW

35
AMP.
ALTERNATOR
REAR
VIEW
40
& 55 AMP.
ALTERNATOR
given in Par. H-78, adjusting the fan belt to its
proper tension after the alternator is mounted, as described in Par. C-27. Wires should be connected
as shown in Fig. H-38.

When
the vehicle is equipped with a radio, a .55
mfd. capacitor is required on the alternator. Mount
the capacitor strap to a ground terminal and con­
nect the lead to the output terminal.
H-88.
STARTING
SYSTEM
SERVICE
H-89.
Ignition
Switch

The
ignition switch serves both to energize the
ignition system and
engage
the starter switch.
The
ignition switch has four positions: (1) AC­

CESSORY,
(2)
LOCK,
(3) ON, and (4)
START. The
key must be in the switch to turn it to any position other than
LOCK,
and the key can be
removed only in the
LOCK
position.
In "ACC",
a connection is made from the battery

terminal
to the accessory terminal of the switch to
allow accessories such as the radio, blower and/or
windshield wiper to be operated with the ignition, fuel
gauge
and indicator light circuits off.
In "LOCK",
no accessory supplied through the
ignition switch can be operated. Also, the ballast
resistor (V-6
engine
only) circuit to the ignition
coil
(IGN) is grounded.
In
"ON", a connection is made from the battery

terminal
to the accessory terminal so that all
ignition switch supplied accessories can be operated. Also the battery is connected to the ballast resistor
(V-6
engine
only) leading to the ignition coil

(IGN).
From
this same terminal, a lead
into
the
instrument cluster energizes the fuel
gauge
and
indicator lights.
In "START",
all ignition switch supplied acces­
sories are temporarily disconnected. A connection is made to the starter solenoid lead. The charge

and
oil indicator lamps
will
light until the
engine
is started.
H-90.
Ignition
Switch
Removal

a.
Remove the bezel nut and pull back the main
switch body.
Lower
the switch
body
from under the instrument panel so that the wiring harness plug

can
be removed from the prong connection,
b. If the lock cylinder is to be removed, turn the
ignition key to the right and insert a short
piece

of wire or end of a paper clip
into
the lock release

hole
in the switch body. Pressing on the lock
cyl­
inder retainer
will
allow the cylinder to be removed.
H-91.
Ignition
Switch
Installation

Before installing the lock cylinder
into
the main
switch body,
note
the position of the lock cylinder
retainer.

a.
Place the lock cylinder
into
the main switch
body
with the highest part of the lock cylinder
retainer in line with the lock release
hole
in the
main
switch body.
b. Compress the lock cylinder retainer so that the
lock cylinder can be installed all the way
into
the

main
switch
body
or until the retainer can be

seen
through the pin hole.

c.
Install
wiring harness plug
onto
switch
body

prong connection.

d.
Install
this main switch
body
into
the instru­
ment panel opening from the
rear.

e. To make sure that the switch is in its correct position, install the ignition key in the off position.
Then
turn the switch
body
until the key is straight
up and down. Remove the key, install the bezel
nut and secure.
H-92.
PRESTOLITE
STARTING
MOTOR
DAUNTLESS
V-6 and

HURRICANE
F4
ENGINE

The
Prestolite starting motor on the V6
engine
is

similar
in construction (with exception of pinion housings) to the starting motor installed on F4

engines.
The
starter solenoid switch is bolted to the starter
frame.

The
starter is equipped with
sealed-type
absorbent
bronze bearings and no lubricant is required. Service procedures for the Prestolite starter are
given in
Pars.
H-93 to H-107. 202

<jeep»
UNIVERSAL
SERIES
SERVICE
MANUAL

H

t
^

12956

FIG.
H-41—PRESTOLITE
STARTING
MOTOR—V-6
ENGINE

1—
End
Plate
2—
Oiling
Pad

3—
Thrust
Washer
4—
Brush
Plate Assembly 5—
Screw

6—
Lock
Washer 7—
Insulating
Washer
8—
Terminal

9—
Field
Coil
and Pole Shoe

10—Frame
11—
Insulating
Washer
12—
Washer

13— Nut
14
—Lockwasher

15—
Insulating
Bushing
16— Pole Shoe Screw
17—
Bearing,
Outer
18—
Drive
End
Frame
Pinion Housing
19— Intermediate Bearing Housing
20—
Lock
Washer 21—
Screw

22— Bendix Drive
23—
Thrust
Washer

24—Pin

25—
Armature

2 6—Commutator
27—
Thru
Bolt
28—
Insulator

29—
Bearing,
Intermediate
and
the armature rotated slowly by hand. If a
shorted coil is present, the steel strip
will
become
magnetized and
will
then vibrate.
H-101-
Field
Coils

Using
test
probes, check the field coils for both
ground and
open
circuits.

a.
To
test
for ground, place one probe on the motor frame or
pole
piece
and touch the other probe to the field coil terminals. If a ground is present, the
lamp
will
light.
b.
To
test
for
open
circuits, place the probes on
the field coil terminal and on an insulated brush.
If
the light,
does
not light, the coil is
open
circuited.
H-102.
Brush
Holder Inspection

Using
test
probes, touch the insulated brush holder with one probe and a convenient ground on the commutator end head with the other probe. If the
lamp lights, it indicates a grounded brush holder.
H-103.
Starting Motor Reassembly

Refer
to Fig. H-40 and H-41.

a.
When assembling absorbent bronze bearing
found in the end plate and drive end frame, always
use the proper arbor
designed
to
give
the proper
bearing fit. Soak the bearings in oil
before
assem­
bling in the bearing bore. Give the bearing
seats

a
light coating of oil.

Note:
At assembly, the outer pinion housing bear­
ing must be flush with the bearing bore on the inside of the housing; the intermediate bearing
must be flush with the bearing bore on the side
toward the armature.

b.
Brushes should be correctly installed and con­
nected as outlined in Par. H-98 in order to be sure
of proper starting motor efficiency.
c. Assemble the armature bearing plate and Bendix

Folo-Thru
Drive to the drive end frame.
Install
the two holding cap screws and lock washers. Tighten them securely. 205

H

ELECTRICAL
SYSTEM

FIG.
H-42—GROWLER
d.
Install
the armature in starter motor frame,
using care to align the four brushes and brush
springs on the commutator so that they are free to
move
and are square on the commutator.

e.
Install
the thrust washer on the shaft.
Lubricate

the plug and bearing in the end plate.
Install
the
end plate.
Install
the two through
bolts
and tighten securely.

f.
On Prestolite V6 starting motors, check pinion position by measuring from the centerline of the
pinion housing mounting bolt
holes
to the outside

edge
of the pinion.
Correct
measurement with the
Bendix
drive retracted is [19,05 mm.] to
%"
[22,23 mm.]; with drive extended, 1%"

[34,93
mm.] to 1^" [38,10]. Adjust by installing

thrust
washers just inside the commutator end
head or intermediate bearing as required. The
Bendix
drive retaining pin must not project
beyond the outside diameter of the pinion
sleeve.

H-104.
Bench Test

The
motor should first be checked to see that the
free running
voltage
and current are within specifi­ cations. To
test,
connect the motor to a battery,
ammeter and voltmeter. If the current is too high
check
the bearing alignment and end play to make

sure
there is no binding or interference. Using a

spring
scale and torque arm check the stall torque to see that the motor is producing its rated
crank­

ing power. The stall torque
will
be product of the

spring
scale reading and the length of the arm

in
feet.
If the torque is not up to specifications

check
the seating of the brushes on the commutator
and
the internal connection of the motor for high
resistance. The Bendix
Folo-Thru-Drive
should be checked for correct operation. The Bendix pinion
should be checked to see that it shifts when the motor is operated under no load.

H-105.
Bendix Folo-Thru Drive (Prestolite)
The
Bendix
Folo-Thru
Drive is designed to over­

come
premature demeshing of the drive pinion
from
the flywheel ring gear until a predetermined

engine
speed is reached. See Fig. H-43. No repairs or adjustments are possible on this

drive
and a
complete
new unit must be installed

if
trouble develops.

H-106.
Lubrication
of
Folo-Thru Drive
A
periodic cleaning and relubrication of the drive is advisable, the frequency of which
will
depend on
the type of service to which the vehicle is sub­
jected and the locale of operation.

a.
Remove the starting motor from the
engine
and take off the outboard housing. The pinion and

barrel
assembly
will
be in the demeshed position
on the screwshaft. Do not
move
it forward
until
after
that portion of the armature shaft ahead
of the pinion has been cleaned. If accidentally ro­
tated to the outer end of the screwshaft it
will

lock
in that position and cannot be forced back.

b.
Do not disassemble the drive for any reason.

c.
Do not dip or wash the drive in any cleaning solution.

d.
Do not remove the drive from the armature
shaft. Remove
excess
oil, grease or foreign matter
from
the armature shaft by wiping it with a clean cloth.
3
10859
FIG.
H-43—BENDIX
FOLO-THRU DRIVE

Dampen
the cloth with kerosene if necessary. A
light film of
SAE
10 oil may then be applied to the shaft.

e.
Now rotate the pinion and
barrel
assembly to the
fully
extended position, thereby exposing the screw­ shaft triple threads. Use a cloth dampened with
kerosene to wipe them clean. Do not use
gaso­
line
or any
commercial cleaner.
If the dirt is

thick
and gummy, apply the kerosene with a small

brush.
Tilt
the starting motor so that a small
amount
will
run under the control nut. Relubricate

with
a thin film of
SAE
10 oil. Use SAE 5 at ex­ tremely low temperatures.

f.
Reassemble the starting motor to the
engine
with the drive in the extended position.
Carefully
mesh the pinion with the flywheel ring gear before
tightening the starter motor mounting bolts. It may 206

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

H
require
a slight rotation of the pinion to index it
into the ring gear. When the
engine
starts the drive
pinion
will
automatically demesh from the ring
gear and return to its normal position.
H-107. Starter Solenoid Switch (Prestolite)
•
Refer to
Figs.
H-44 and H-45.

Should
a starting motor
fail
to deliver maximum power the fault may be due to
voltage
drop at the
starting switch contacts due to corrosion or
burn­

ing.
Check
the switch by comparing the
voltage

at the battery terminals and that at the starting 13407

FIG.
H-44—STARTER SOLENOID—HURRICANE
F4
FIG.
H-46—PRESTOLITE STARTER
AND SOLENOID—V-6 ENGINE
switch terminals. The
voltage
drop should not
exceed .05 volts per 100 amperes.
Should
it be impossible to file the switch contact
plates to obtain a clean
full
surface contact the
switch should be replaced.
Current
model starting switches are of the
solenoid type, mounted directly on the starting
motors.
This
type switch is energized by turning
the ignition key to the extreme right position.

Should
a solenoid switch
fail
in service it is neces­

sary
to install a new solenoid assembly,
a.
To remove the solenoid switch first remove the nut and lock washer securing the solenoid strap to the starter
post.
Then
remove nut and lock washer securing battery positive cable to solenoid
post.

Tape
end of battery cable to eliminate the pos- 207

H

ELECTRICAL
SYSTEM
sibility
of the cable shorting at the
engine
or frame.
Remove nut and lock washer securing the ignition

wire
to the solenoid
post
and remove the two screws and lock washers securing the solenoid to
the starter frame. Remove the switch,
b.
To install the solenoid switch reverse the re­

moval
procedure given above.

H-10S.
STARTING MOTOR
—
DELCO
DAUNTLESS
V-6
ENGINE

Refer
to Fig. H-45.

The
starting motor used on the Dauntless V-6 en­

gine
has an integral solenoid switch and enclosed
shift lever which first shifts the overrunning clutch
pinion into
engagement
with the ring gear on the
flywheel of the
engine
and then
closes
the electrical
circuit
to cause
engine
cranking. When the
engine

starts,
the overrunning clutch
disengages
to pre­ vent transfer of
engine
speed to the starting motor.

Note:
Should a service replacement starter motor
be required the factory recommends replacement

with
original equipment parts; however, should the need arise an existing starter motor (Delco or
Prestolite) could be replaced with the current
Delco-Remy
starter, model 1108375, with the
following modifications to the wiring harness. If
the existing starter motor wiring harness
does
not
provide a 12 ga. purple conduit wire, (connects the ignition switch to the starter motor) then a 12 ga.

purple
conduit wire 70 inches long, must be in­

stalled.
Should the existing starter motor wiring
harness
contain a 16 ga. light blue conduit wire, (connects the ignition switch and starter motor)
bend this wire back and tape out of the way.

H-109.
Starting Motor Disassembly
a.
Before removing the starting motor from the
engine, disconnect leads and cover battery lead

terminal
with piece of
hose
or tape to prevent
short circuiting.
Note
locations of wiring connec­
tions to assure proper reconnection. Remove the cap screw that secures the starting motor to the
angle bracket on the side of the engine. Remove
the two cap screws that secure the drive end of
the starting motor to the cylinder block; remove
the starting motor.

b.
Remove terminal nut and disconnect field lead,

which
passes through grommet at top of motor,
from
motor terminal of solenoid. Remove two
thru

bolts
from motor. Remove commutator end frame

and
field frame assembly from solenoid and drive assembly.
e.
Pull
out pivot pins of brush holders and remove each of two brush holder and spring assemblies

from
field housing. Remove screws which attach
brushes and leads to holders.

d.
Remove armature and drive assembly from
drive
housing. Remove thrust collar from pinion
end of armature shaft. Remove leather thrust

washer
from
opposite
end of shaft.
e. To separate drive assembly from
armature,
place

a
metal cylinder of proper size (J^" [12,7 mm.]
pipe coupling is satisfactory) over end of armature
shaft to bear against the pinion
stop
retainer. Tap
retainer
toward armature to
expose
snap ring as
shown in
Fig.
H-47. Remove snap ring from
groove
in
shaft; slide retainer and pinion drive assembly

from
shaft. Remove assist spring from shaft,

f.
Remove two screws holding solenoid switch to
drive
housing remove switch. Remove small nut

and
insulating washer from the solenoid S terminal.
Remove nut and insulating washer from the
sole­

noid battery (large) terminal. Remove two screws that attach switch cover to solenoid and remove cover for inspection of switch parts. Remove shift
lever fulcrum bolt and remove shift lever, plunger,

and
return spring.
12765
FIG.
H-47—REMOVING PINION
DRIVE
ASSEMBLY

FROM
ARMATURE SHAFT

1— XA ' Pipe Coupling

2—
Snap
Ring
and Retainer

3—
Armature
Shaft
4—
Drive
Assembly
H-110.
Starting
Motor
Cleaning and
Inspection

a.
Wipe all parts clean with clean cloths. The
arma­
ture,
field coils, and drive assembly must not be
cleaned by any degreasing or high temperature
method.
This
might damage insulation so that a
short
circuit
or ground would subsequently develop.
It
would also remove lubricant originally packed

in
the overrunning clutch so that clutch would

soon
be ruined.

b.
Carefully
inspect all parts visually for wear or
damage. Make necessary repairs or replace unserv­
iceable parts. Any soldering must be
done
with

rosin
flux.

Note:
Never use acid flux when solding any elec­

trical
connections and never use emery cloth to
clean
armature
commutator or other
electrical
units. 208

H

ELECTRICAL
SYSTEM
FIG.
H-49—INSTALLING PINION
STOP RETAINER AND THRUST

COLLAR
ON ARMATURE SHAFT
1—
Retainer

2—
Snap
Ring

3—
Thrust
Collar

4—
Drive
Assembly 5—
Retainer

6—
Groove
in Armature Shaft 7—
Snap
Ring

e. Place thrust collar on armature shaft with shoulder next to snap
ring.
Move the retainer
into contact with
ring.
Using pliers on
opposite

sides of shaft,
squeeze
retainer and thrust collar

together
until snap ring is forced into the retainer.
See Fig. H-49, right hand view.

f.
Lubricate
bearing of drive housing with silicone grease and install armature and drive assembly
in
housing.
g. If field coils were removed from field frame, position coils of replacement field coil assembly
on
pole
shoes
and mount each
pole
shoe
in field
frame
with a
pole
shoe
screw. Use care in tighten­ ing screws to avoid distortion of parts. Be certain
that screws are securely tightened. Insert ends of
field
coil
leads through rubber bushing in field
frame.

h.
Position field frame assembly over armature as­
sembly so that its dowel pin
engages
the
hole
in

drive
housing. Use care to prevent damage to brushes and brush holders. Make sure that brushes

are
properly sealed on commutator.

i.
Install
leather thrust washer on commutator end
of armature assembly.
Lubricate
bearing in com­
mutator end frame with silicone grease and position
end frame to field frame so that armature shaft
enters bearing. Secure field frame and end frame
to drive housing with two
thru
bolts. Connect field leads to motor terminal of solenoid with connect­ing nut.

j.
Whenever the starting motor is disassembled
and
reassembled, the pinion clearance should be
checked.
This
is to make sure that proper clear­
ance exists
between
the pinion and the pinion

stop
retainer when pinion is in cranking position.

Lack
of clearance would prevent solenoid starter

switch
from closing properly; too much clearance
would cause improper pinion
engagement
in ring gear.

k.
Supply 6 volts (3 battery cells or a
6-volt
bat­

tery)
between
S terminal of the solenoid and ground (starter frame).
Caution:
Do not supply more than 6 volts or the
motor
will
operate. As a further precaution to
prevent motor operation, connect a heavy jumper

wire
from the solenoid motor terminal to ground.

I.
After energizing the solenoid, push the drive as­
sembly away from the
stop
retainer as far as pos­
sible and use a feeler
gauge
to check clearance

between
pinion and retainer. See Fig. H-50. If pinion clearance is not .010" to .140" [0,25 a 3,55

mm.],
there is either excessive wear or improper as­
sembly of solenoid linkage or shift lever mechanism.
12771
FIG.
H-50—MEASURING PINION CLEARANCE
1—
Press
Rearward

2—
Pinion

3—
Retainer

4— .010* to .140* Clearance 5—
Feeler
Gauge
210

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

H
Note:
Pinion clearance cannot be adjusted. If
clearance is not correct, motor must be disassem­
bled and checked for the above mentioned defects.

Any
defective parts must be replaced.
H-118. Starting Motor Test —
Genera!

To
obtain
full
performance data on a starting motor, or to determine the cause of abnormal
operation, the motor should be submitted to no-
load and locked armature
tests,
with equipment designed for such
tests.
A high-current variable resistance is required to obtain the specified volt­
age at the starting motor.
This
is necessary since
a
small variation in the
voltage
will
produce a
marked
difference in the current
drawn.

H-119.
Starting Motor No-Load Test

This
test
requires a DC voltmeter capable of
read­

ing
voltages
in a 12-volt
circuit,
a DC ammeter

with
maximum range of several hundred amperes,
a
high-current variable resistance, an rpm. in­

dicator,
and a fully-charged, 12-volt battery.

a.
Connect a jumper lead
between
S terminal
and
large battery terminal of starter solenoid.
Con­
nect voltmeter
between
either of
these
terminals (positive) and motor frame (negative, ground).

Connect
ammeter and variable resistance in series

between
positive terminal of battery and battery

terminal
of solenoid. Set up rpm. indicator to show starting motor speed.
b.
Initially,
adjust variable resistance to a value of
approximately .25 ohm. To complete the
circuit,

connect negative terminal of battery to motor

frame.
Adjust variable resistance to obtain a volt­ meter reading of 10.6 volts;
note
speed of starting motor and ammeter reading. Motor speed should
be
6750
to
10,500
rpm.; ammeter reading should
be 50 to 80 amperes.
c. Rated speed and current indicate normal condi­
tion of the starting motor. Low speed and high
cur­
rent
may show friction; this could be caused by
tight, dirty, or worn bearings, bent armature shaft,

or
a
loose
field
pole
shoe
dragging against the

armature.
It could also be caused by a short-cir­ cuited armature, or by grounded armature or field
coils.

d.
Failure
to operate and high current indicates

a
direct short circuit to ground at either the battery

terminal
or field coils.
e.
Failure
to operate and no current are usually
caused by broken brush springs, worn brushes, high insulation
between
commutator
bars,
or
some
other
condition preventing
good
contact
between
the brushes and commutator. It can also be caused by
open circuit in either the field coils or armature coils.
f. Low speed and low current show high resistance due to poor connections, defective leads, dirty com­
mutator, or one of the conditions mentioned in e,
above.
g. High speed and high current indicates a short
circuit
in the field coils. H-120-
Locked
Armature Test

This
test
requires a DC voltmeter with range ap­

propriate
to read
voltages
in a 12-volt
circuit,
a DC
ammeter with maximum range of several hundred
amperes, a high-current variable resistance, a
clamping fixture to lock
together
the motor shaft

and
case, and a fully-charged 12-volt battery.

a.
Connect a jumper lead
between
S terminal and
large battery terminal of starter solenoid. Connect
voltmeter
between
either of
these
terminals (posi­
tive) and motor frame (negative, ground). Connect
ammeter and variable resistance in series
between
positive terminal of battery and battery terminal
of solenoid.
Install
clamping fixture to lock motor
shaft and case
together
securely.
b.
Initially,
adjust variable resistance to approxi­
mately .05 ohm. To complete the
circuit,
connect
negative terminal of battery to motor frame. Ad­

just
variable resistance to obtain a voltmeter
read­
ing of 4.0 volts. Ammeter reading should be 280
to 320 amperes.

H-121.
Solenoid Starter Switch — Delco

The
solenoid-type switch is mounted directly on
the starting motor.
This
type of switch is energized
by turning the ignition key to the extreme right position. Should the solenoid switch
fail
in service

it
is necessary to install a new assembly.

Should
a starting motor
fail
to deliver maximum power the fault may be due to
voltage
drop at the

starter
switch contacts due to corrosion or burning.

Check
the switch by comparing the
voltage
at the
battery across the terminals. The
voltage
drop
should not exceed .05 volts per 100 amperes.
In
order to remove the starter solenoid, it is neces­

sary
to remove the starter assembly.

H-122.
ELECTRICAL
INSTRUMENTS

H-123.
Fuel
Gauge —
CJ-3B

The
fuel
gauge
circuit is composed of the indicating

unit,
mounted on the instrument panel, and the
fuel tank unit, connected by a single wire through the ignition switch.

Should
the
gauge
fail
to register, check all wire con­ nections to be sure they are tight and clean; also
be sure both units are well grounded. If, after this
check, the
gauge
does
not indicate properly, remove
the wire from the tank unit and connect it to a
new tank unit which must be grounded to the tank

or
frame for
test.
Turn
the ignition switch "ON"
and
move
the float arm through its range of travel,
watching the dash unit to determine if it indicates
correctly.
If it fails to do so the trouble is probably

in
the dash unit and it should be replaced.

Should
a new tank unit be unavailable for this
test,
disconnect tank unit wire at the instrument panel

gauge.
Connect one lead of a 12 V, 1 CP
test
light
to the instrument panel unit terminal and with the
ignition switch
"ON"
ground the other lead. If the
unit is operating correctly the pointer
will
move

approximately three-quarter across the
dial.
Do not attempt to repair either unit; replacement
is the only precedure. 211