ignition JEEP DJ 1953 Repair Manual

H

ELECTRICAL
SYSTEM
H-124. Testing Indicators and Gauges

Two
gauges
(fuel and temperature) and two in­ dicators (oil pressure and battery charge) that are
located in the instrument cluster are electrically operated.

The
fuel
gauge
is connected by a single wire to a
float-and-slide-rheostat sending unit in the fuel
tank.

The
temperature
gauge
is connected by a single

wire
to a resistance-type sending unit mounted on the engine.

The
battery charge indicator operates when there
is a difference in potential
between
the generator
and
the battery
.The
battery charge indicator lights
when the generator is not charging the battery. The
indicator
light
goes
out when the generator
begins

to charge the battery.

The
oil pressure indicator is connected by a single

wire
to a diaphragm switch located on the engine.
When
engine
oil pressure is low or zero and the
ignition switch is on, the oil pressure indicator
will

light. When
engine
speed is increased slightly above idle speed, raising the oil pressure to approximately 6 psi. [0,2 kg-cm2], the diaphragm switch
will
open the circuit and the indicator light
will
go out.

A
voltage
regulator maintains a constant
voltage
to the
gauges
in normal operation. On early vehicles,
this
voltage
regulator was mounted on the
rear
of
the instrument cluster. On current vehicles, the
voltage
regulator is integral with the fuel
gauge.

Should
trouble
develop
in the
gauges,
first check the regulator (fuel
gauge
on current production vehicle). If the
voltage
to the regulator is below 10 volts system low
gauge
readings
will
result.
Voltage in
excess
of 16 volts
will
not affect
gauge

readings but may result in premature wear of the
regulator contacts. If the
voltage
to the regulator is

within
the above limits, check the electrical con­ nections to the regulator (or fuel gauge), especially
the ground connection. If the readings of all the
gauges
is too high, or they all read too low, replace
the regulator (or fuel gauge).

If
the temperature
gauge
or heat indicator in the
instrument cluster have failed, the cause may
originate from the jumper bar shorting out against the instrument case.
Check
the jumper bar
between

the temperature
gauge
and heat indicator at the

rear
of the instrument case. On later production vehicles, the jumper bar is covered with an in­
sulating
sleeve
to protect it from shorting out
against the instrument case. If the jumper bar

does
not have this
sleeve,
either install one or

wrap
the bar with plastic electrical tape to
half

an
inch [12,7 mm.] from each end. When installing the jumper bar, be sure the curved
segment
is
closest to the fuel
gauge.

Should
only one of the two
gauges
register incor­
rectly,
check the lead wire from the
gauge
to the
sending unit for shorts or open connections. Next disconnect the
gauge
from the sending unit, and
connect the
gauge
to a new fuel tank sending unit

which
has been grounded to the vehicle.
If
the
gauge
registers incorrectly when operating the new unit,
replace the
gauge;
if correctly, replace the sending

unit.

Should
a new fuel tank unit not be available for testing, use a 12-volt
test
light in its place. When
the
gauge
is operating correctly, the pointer
will

move
approximately three-quarters across the
dial.

On
some
vehicles, the temperature
gauge
may
register on or
close
to the H (hot)
mark
when
coolant temperature is
190°F.
to
200°F.
[88°C.
a

93°C.].
In such cases, a 25-ohm,
1-watt
resistor
may be installed on the temperature
gauge
which

will
place the pointer just beyond the center
mark
at a coolant temperature of
190°F.
to
200°F.
Install

the resistor
between
the two terminals on the back
of the
gauge.
Insulate the
exposed
leads of the resistor with electrical tape.

If
the oil pressure indicator
does
not indicate cor­

rectly,
first check the light bulb. Next check all
connections and lead wires. If, after all possible

defects
are corrected, the indicator light
does
not go on and off properly, then the diaphragm type
switch in the cylinder block should be replaced.

H-12S.
LIGHTING SYSTEM The
wiring of the lighting systems is shown in
the wiring diagrams, which indicate the various units in relation to their positions in the vehicle.
The
wires in the various circuits are of different
colors or are marked by tracers to aid when check­
ing individual circuits.

The
lighting circuits of all models are protected by

an
overload circuit breaker mounted on the back of the main light switch and no replaceable fuse is
required.

The
upper and lower headlight beams are con­
trolled by a
foot
switch located on the toe board
to the left of the clutch pedal.
H-126.
Main
Light
Switch

This
switch is a dual functioning unit having two

push-pull
positions and a rotary action. When
pulled out to the first position, the front parking
and
tail
lights are turned on. When pulled all the
way out to the second position, the headlights and
tail
lights are turned on. Rotating the switch to
the right dims the instrument cluster lighting.

The
switch may be removed from the instrument
panel by first loosening the set screw in the control
knob and removing the knob. The retaining nut may then be removed and the switch removed
through the
rear
of the instrument panel.
FIG.
H-51—MAIN
LIGHT
SWITCH
(EARLY)

1—
Battery
4—Parking Lights
2—
Rear
Lights 5—Auxiliary

3—
Head
Lights
212

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL
H
FIG.
H-59—HEAD LAMP

1—
Door

2—
Retaining
Screw

3—
Retaining
Ring

4—
Sealed
Beam
Unit
5—
Mounting
Ring

6—
Adjusting
Screw 7—
Housing

8—
Wires

9—
Door
Screw 310669
to cross the vertical
tapes
at the measured height
of each lamp center respectively.

g.
Remove the head lamp doors.
h.
Clean
the head lamps.

H-132.
Aiming Head Lamps

a.
Turn
the headlights on low beam. Cover the lamp not being aimed. Be sure to use the horizontal reference line on the screen that is the same dimen­
sion as the vehicle lamp height.
b.
Turn
the vertical aiming screw counterclock­
wise until the lamp beam is considerably lower

than
the horizontal reference line on the screen.
Then,
turn
the screw clockwise until the top
edge

of the high intensity
area
is even with the horizontal

line.
See Fig. H-60.
I
(T)

JT)

1'.'' | '':'
11460

FIG.
H-60—HEADLIGHT AIMING
CHART
1—
Vertical
Tape,
Left
Lamp
Center

2—
Vehicle
Centerline

3—
—Vertical
Tape,
Right
Lamp
Center
4—
Zone
of Greatest Intensity
5—
2
*
(Two Inches)
6— 25'0
'
7—
2
*
(Two Inches)
8—
Height
of
Lamp
Centers
9—
Horizontal
Tape

Note:
Always bring the beam into final position
by turning both aiming screws clockwise so that
the unit is held under proper tension when the operation is complete.

c. Turn
the horizontal aiming screw counterclock­
wise until the beam is off.
Then,
turn
the same
screw
clockwise until the
left
edge
of the high
intensity area is 2" [5,08 cm.] to the right of the
lamp center line. See Fig. H-60.

d.
Cover the lamp that has been aimed and aim
the other lamp using the same procedure.
e.
Carefully
reinstall the head lamp doors.

H-133.
Parking
and
Turn Signal Light
The
parking lights are mounted in the radiator

guard
panel just below the headlights. These lights

are
on only when the main switch control knob is
pulled
out to the first notch.

To
replace a parking lamp, remove two screws allowing the lens and colored reflector to be re­
moved. Replace the lamp, which is recessed back

in
the housing.

If
the
complete
parking light assembly is to be
removed for service or replacement, disconnect the

wire
plug at the back of the housing.
Then
remove
the nuts and lock washers securing the parking light assembly and remove out the front of the

panel.

H-134. Tail, Stop
and
Turn Signal Light

Refer
to Fig. H-57 and H-58.

The
tail
lights are mounted in the
rear
corner
posts

of the body. They are on whenever the main switch
control
knob is pulled out to any position.

a.
To replace a lamp, remove the snap ring on

early
models
and remove the lens; on late
models
remove lens screws, lens and gasket.
Clean
lens
and
reflector before replacing.
b. To remove the parking and
tail
light housing,
disconnect wiring, remove the two nuts and lock
washers securing
tail
light assembly to body and remove from
rear
of body.

H-135-
Backup Lights •
Refer to Fig. H-61.

The
backup lights on late production vehicles are located on the
rear
of the vehicle directly below
the
tail
light. The backup lights are actuated
through a switch when the ignition is on and the

transmission
is in reverse. 215

ELECTRICAL
SYSTEM

14385

FIG.
H-61—BACK-UP
LIGHT
1—
Snap
Ring
2—
Lens

3—
Gasket

4—
Bulb
5—
Housing
and
Cable
On
late production
T14A
transmissions the backup
light switch is threaded into the right
rear
corner
of the cover housing and is activated by the move­
ment of the reverse shift
rail.

The
backup light switch is not serviceable and
must be replaced if defective.

Bulbs
can be replaced by removing the snap
ring,

lens and gasket from the assembly.

H-136.
License Plate
Light

On
CJ-5A,
CJ-6A
and current production vehicles
the license plate light is attached to the tailgate
and
is of the swing-type design to enable the
license plate to be visible when the tailgate is in
the down psoition. The bulb can be changed by
removing
the clear plastic lens. On early production
vehicles the license plate light is integral with the

tail
light assembly.

H-137.
Horn
The
horn is mounted under the hood on the
left

front
fender. The horn is sounded by pressing the
button located at the top center of the steering
wheel.

To
remove the horn wire, disconnect the wire at
the snap connection at the base of the steering
column.
Pull
off the rubber horn button cap and
the brass contact cap from the steering wheel nut.

This
will
expose
the contact tip of the horn wire.

Pull
the wire out of the steering column from the top. Refer to Fig. H-62.

H-13S.
Directional
Signals

Fig.
H-63 shows the
wiring
of a
composite
direction­

al
signal
circuit.
The most frequent causes of
failure
in
the directional signal system are
loose
connec­
tions and burned-out bulbs. A flashing rate

approximately
twice the normal rate usually in­
dicates a burned-out bulb in the
circuit.
11087

FIG.
H-62—HORN
BUTTON 1—
Cap
2— Nut
3—
Horn
Button
Spring
Cup 4—
Ferrule

5—
Horn
Cable

6—
Contact
Disc

7—
Steering
Wheel
8—
Cup
9—
Bearing
Spring
Seat
10—
Steering
Column

11—
Tube

12—
Bearing

13—
Bearing
Spring

14—
Horn
Button
Spring

15—
Retainer
Spring
When
trouble in the signal switch is suspected it
is advisable to make the following
test
to definitely
locate the trouble before
going
to the effort of

removing
the signal switch. If, for example, the
right
rear
stop
light and right front parking light

are
inoperative and switch failure is indicated, first put the control lever in neutral position.
Then

disconnect the wire to the right side
circuit
and
touch it to or bridge it to the
"L"
terminal, thus
by-passing the signal switch. If the right side cir- 10609

FIG.
H-63—DIRECTIONAL SIGNAL
CIRCUIT

1—
Flasher

2—
Ignition
Switch

3—
Control
4—
Light
Switch
5— Stop
Light
Switch
216

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

H
cuit
lights,
the
signal switch
is
inoperative
and

must
be
replaced.

H-139.
Hazard
Warning Lights

All
current production vehicles
are
equipped with

a
four-way flasher warning system.
The
control switch
is
located
on the
instrument panel left
of

the steering column.
With
the
switch pulled
out,
the
two
front and
two
rear
turn
signal lights flash
on and
off
simultaneously,
as do
both
turn
signal

indicator
lights
on the
instrument clusters.
H-140.
Marker
Lights and Reflector Assembly

The
marker
lights
and
reflector assemblies
on

current
production vehicles
are
mounted
on the

side
of
the front fender and
on the
side
of
the
rear
quarter
panel.
The
spare wheel also mounts
a

marker
light. Some earlier production vehicles have
reflex reflectors mounted on the side of the hood and
on
the
side
of
the
rear
quarter panel. determine
if
dash wiper switch or wiring
is at
fault,
disconnect wiring harness from wiper motor
and

try
operating wiper independently
of
dash switch.
If
still
inoperative
see
procedure under
Par.
H-145.
b. Wiper
will
not
shut
off
— Determine
if
wiper
has both
low
and high speeds, slow speed only,
or

high speed only.
It is
important that
the
wiper
operates
at low
speed during parking cycle.
Dis­
connect wiring harness from wiper motor
and try

operating wiper independently
of
dash switch.
If

wiper
shuts
off
correctly with
crank
arm
in
park
position and wiper has both speeds, check
the
lead

between
terminal
and
dash switch ground
and

check
for
defective dash switch.
If
wiper shuts
off

correctly,
but has
high speed only, check lead
be­

tween wiper terminal and dash switch
for an
open

circuit
and check
for
defective dash switch.
If
still

inoperative,
see
Par. H-145.
c. Wiper
has
only fast speed.
Check
for
defective dash switch
or
open lead
between
terminal
and

dash switch.

H-141.
Windshield Wiper System

Early
production vehicles equipped with
the
Dauntless V-6
engine
have
two
single speed wind­
shield wiper motors mounted above
the
windshield inside
the
vehicle. The wiper motors
are
operated

and
controlled
by a
switch located
on the
instru­
ment panel.

Current
production vehicles with stationary wind­
shield have
a
two-speed
electric windshield wiper motor mounted below
the
windshield outside
the

vehicle on the driver's side. The wiper motor switch is located
on the
instrument panel
to the
left
of

the steering column.

H-142.
Two-Speed Wiper Motor

The
two-speed
electric wiper motor
is
operated and
controlled
by a
turn
type, three poled, dash switch,
containing
a 6
amp. circuit breaker.
Current
flow
is directed from
the
battery through
the
ignition
switch
to the
wiper dash switch assembly
to the

two-speed
wiper motor, which passes current from the designated motor brush (high,
low or
park)
to

the armature circuit
to
ground.

H-143.
Troubleshooting Procedure
Troubleshooting procedures
are
divided into
two

categories: wiper troubleshooting
in
vehicle; wiper
troubleshooting
on
bench.
Fig. H-65 and H-66

illustrates connecting leads
of the
two-speed
wiper for either bench operation
or to run
wiper inde­
pendently
of
dash switch and vehicle wiring when
installed
in the
vehicle.
H-144. Wiper Troubleshooting
in
Vehicle

Typical
wiper troubles and remedies are
as
follows
:

a.
Wiper
is
inoperative
—
Check
wiper switch
cir­

cuit
breaker; wiring harness connection
at
wiper
motor
and
wiper switch; wiper motor
feed
wire

from
ignition starter switch
to
wiper switch;
and
check wiper
on
switch
to be
securely mounted.

With
ignition switch
on,
check
for 12
volts
at
har­

ness
terminal that connects
to
wiper terminal.
To
BLACK
PARK

GREEN *-
RED m~
LOW
PARKING
<^^>

SWITCH
V^-O*'
HIGH

FIG.
H-64—WIRING
DIAGRAM

FIG.
H-65—WINDSHIELD
WIPER
SWITCH
ASSEMBLY
(EARLY)
1.
Park
(black)
2. Low (green)

3.
High (red)
d.
Wiper
has
only slow speed
and
shuts
off
with
dash switch in high speed position. Reverse harness
leads that connect
to
wiper terminals.

e. If
blades
do not
return
to
park
position when

wiper
is
turned
off,
check wiper ground connection
to vehicle body. Remove wiper from vehicle
and

check
for
dirty, bent,
or
broken
park
switch con­
tacts.

f.
If
wiper speed
is
normal
in
slow,
but too ex­
cessive
in
fast speed, check for an open terminal. 217

'Jeep*
UNIVERSAL
SERIES SERVICE
MANUAL

H
H-151.
SERVICE
DIAGNOSIS—Continued

SYMPTOMS PROBABLE
REMEDY

Generator:
(continued)
Fails
To Charge-Open Charging Circuit Correct
Sticking Brushes Repair or Replace
Dirty
or Burned Commutator ... Clean Commutator
Grounded Commutator Replace
Open Circuit in Field Replace
Weak Soldering on Armature. . . Repair Grounded Wiring Repair

Defective
Regulator. .. Replace Regulator
Too High Charging Rate— Regulator Improperly Adjusted Adjust or Replace
Short in Armature Replace Grounded Field-to-regulator Wire Correct
Shorted
Cell
in Battery... Replace Battery

Starting
Motor: Slow Starter Speed— Discharged Battery or Shorted
Cell
Recharge or Repair
Ground
Strap Engine to Frame. Clean Terminals and Tighten
Loose or Dirty Terminals Clean and Tighten
Dirty
Commutator Clean with No. 00 Sandpaper

Worn
Out Brushes Install New Brushes
Weak Brush Spring Tension Replace

Worn
Bearings Replace Burned Starter Switch Contacts Replace Switch

Will
Not
Turn
Engine— Open Circuit at Starter Correct

Solenoid
Open or Stuck Replace
Solenoid
Starter Switch
Defective
Replace Switch
Starter Drive Broken or Stuck. Repair or Replace
Battery Discharged Recharge Battery

Distributor:
Hard
Starting— Distributor
Points
Burned or Pitted Clean
Points
or Replace (Adjust)

Breaker
Arm Stuck on Pivot Pin...... . ... . . . Clean and Lubricate

Breaker
Arm Spring Weak Replace

Points
Improperly Adjusted Adjust
Spark
Plug
Points
Improperly Set Adjust

Spark
Plug Wire Terminals in Distributor
Cap
Corroded Clean
Loose Terminals Check Circuit
Loose or Dirty Terminals on Ground Strap— Engine to Frame. Clean and Tighten
Condenser Faulty Replace Improper Ignition Timing Set Timing

Lights:
Burn
Dim— Loose or Dirty Terminals....... ........ Clean and Tighten
Leak
in Wires. Check Entire Circuit for Broken Insulation
Poor Switch Contact Install New Switch Poor Ground Connection Clean and Tighten

Aim
Headlamp Beams. Use Aiming
Chart
221

H

ELECTRICAL
SYSTEM
H-152.
ELECTRICAL
SPECIFICATIONS—Continued

HURRICANE DAUNTLESS
V-6
DAUNTLESS
V-6 ENGINE
MODEL -
F4
ENGINE
ENGINE
LATE
MODELS

EARLY
MODELS
IGNITION
COIL
BALLAST
]Make Delco-Remy
Prestolite Prestolite
Model
None

1957154

PU
5003

PU
5003

Ohms • • 1.80 @
80°F.

.495 - .605 @
75°F.

.495 - .605 @
75°F.

1.80 @
80°F.

.638 - .835 @
212°F.
.638 - .835 @
212°F.

DISTRIBUTOR:
Prestolite Delco-Remy Prestolite Prestolite
Model
•
(a)
LAY
4012, 4401

1110376

I
AT
4501 or
IAT
4502A
(b)
I
AY
4401A, 44011

IAT
4502

Breaker
Point Gap (b)
.020"
[0,508
mm.] .016"
[0,406
mm.] .016"
[0,406
mm.]
.016"
[0,406
mm.]

Breaker
Arm Tension. ..... 17 to 20 oz.
19 to 23 oz. 17 to 22 oz. 17 to 22 oz.
[482 a 567 gr.] [538 a 652 gr.] [482 a 624 gr.]
[482 a 624 gr.]

42° 29°
to 31°
29°
±3°
29°
±3°

Max.
Auto Advance
(Crankshaft
Degrees) •(a)
11°
@ 1,700 rpm.

13°
to
15°
at 1,950 rpm.
16°
@ 1,800 rpm.
21°
(2 1,800 rpm.

(Crankshaft
Degrees)
(b)
13.5°
@ 1,700 rpm.

26°
@
4200
rpm.
32°
@
4200
rpm.

Max.
Vac. Advance go
(Distributor Degrees)., . .
None

8° 8°
go
Condenser Capacity. . .25 to .28 mfd. .18 to .23 mfd. .25 to .28 mfd. .25 to .28 mfd.

TIMING:
Crankshaft
See
Note

See
Note
See
Note
See
Note

Mark
Location............
Crankshaft
Pulley

Crankshaft
Pulley

Crankshaft
Pulley

Csankshaft
Pulley

Firing
Order
1-3-4-2

1-6-5-4-3-2
1-6-5-4-3-2 1-6-5-4-3-2

SPARK PLUGS:
Make
Champion

A.C. A.C.
or Champion
A.C.
or Champion

J8
44S
44S or UJ 12Y 44S or UJ 12Y

Thread
14 mm.
14 mm. 14 mm. 14 mm.

Thread
Reach
Vz"
[9,47 mm.]
%"
[9,47 mm.]

¥%"
[9,47 mm.]
V8" [9,47 mm.]

Gap
.030"
[0,762
mm.]
.035"
[0,900
mm.] .035"
[0,900
mm.] .035"
[0,900
mm.|

LAMP BULB TRADE
NUMBERS:

Headlight 6012
6012 6012 6012

Parking
and Directional Signals. 1157NA
1157NA 1157NA 1157NA

License
Plate Light........ 1155
1155 1155 1155

Marker
and Reflector 194
194 194 194

INDICATOR LIGHTS:
57 57 57 57
Directional Signals........ 57
57 57 57

Charge
57
57 57 57
57 57 57 57
1156 1156 1156 1156
Instrument Cluster 57 57 57 57

Warning
— 4 Way Flasher. . 57
57 57 57

Brake
Warning Light 57
57 57 57

FUSE
DATA:
Heater 9 amp. 9 amp. 9 amp. 9 amp.

Backup
14 amp. 14 amp. 14 amp. 14 amp.

WS/Wiper.
14 amp. 14 amp. 14 amp. 14 amp.
Directional Signal 9 amp. 9 amp. 9 amp. 9 amp.
4-Way Flasher 14 amp. 14 amp. 14 amp. 14 amp.

Brake
Warning Light 9 amp. 9 amp. 9 map. 9 amp.

FLASHER
DATA:
Directional Signals. 144
144 144 144

Hazzard
Warning. 170
170 170 170

NOTE:
0°
T.D.C.
on Distributor
models
IAY 4401A, IAY 4401B, IAT 4502A.

NOTE:
5°
B.T.C.
on Distributor
models
IAY 4012, IAY 4401, IAT 4501, IAT 4502,
1110376.
224

T
BODY
from the windshield wiper vacuum fitting. On
late

models
disconnect electrical wires from wiper
motor. Unlatch the two windshield clamps on each

side
of the windshield.
Fold
the windshield forward

until
the
slot
in the windshield
hinges
aligns with the flat
side
of the pin in the
body
hinges.
Slip wind­
shield off the pins and remove from
body.

T-4.
Windshield Glass
The
windshield
glass
is mounted in a rubber
weatherstrip which in turn
mounts
in the frame. A
rubber
locking strip, which
holds
the
glass
firmly in
the frame, is inserted in a moulded
groove
around
the rear
face
of the weatherstrip as shown in Fig.
T-2.
To remove the
glass
it is necessary to first
remove the locking strip which may be pried out
with a screwdriver or similar
tool.
Installation is,

obvious.

T-5.
Canvas Tops

Canvas
tops
are available in
Half
Tops and
Full
Tops.
Installation instructions are provided with
each canvas top kit for each model vehicle.
FIG.
T-5—VEHICLE CONTROLS — MODEL CJ-5A, CJ-6A

SINGLE
LEVER
TRANSFER CASE 1—
Hand
Throttle 9—Transfer Case Shift
Lever

2—
Choke
Control 10—Headlight Dimmer Switch
3— Instrument Cluster 11—Clutch Pedal 4—
Light
Switch 12—Heater Controls 5— Ignition — Starter Switch 13—Hand
Brake
Handle
6— Glove Compartment 14—Transmission Shift
Lever
7—
Brake
Pedal 15—Directional Signal Switch
8— Accelerator Pedal 16—Horn Button
FIG.
T-6—TAIL GATE ASSEMBLY —
EARLY
MODEL CJ-5A, CJ-6A
354

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

T
FIG.
T-7—TAIL
GATE
ASSEMBLY

—
LATE
MODEL
CJ-5, CJ-6
T-6.
Care
of
Fabric
Tops
Remove fabric
tops
from their protective covering
immediately after they are received. Store in a

dry,
clean,
airy
place. If the material is damp, the
top should be installed on the vehicle immediately

and
washed with a mild soap; then
give
the top a

quick
and thorough rinsing.
T-7.
Brake
and
Clutch Pedal Pads

A
clutch and brake pedal pad cover has been re­ leased which has a .44" [11,18 mm.]
groove
molded into the back side of the pad cover. When installing,
the grooved opening is located down and to the

bottom
of the pedal. See Fig. T-ll. The purpose of the
groove
concerns models not listed in this
manual.
The pedal pad cover formerly used is
FIG.
T-8—VEHICLE
CONTROLS
—
LATE

CJ-5
AND CJ-6
SINGLE
LEVER
TRANSFER
CASE
1—
Light
Switch

2—
Windshield
Wiper
Switch

3—
Hazard
Warning
Light
Switch
4—
Hand
Throttle*

5—
Choke
Control

6—
Brake
Warning
Light*

7—
Windshield
Washer
Control

8—
Ignition
Starter
Switch

9—
Cigarette
Lighter*

10—
Turn
Signal
Lever

11—
Instrument
Cluster

12—
Horn
Button

13—
Glove
Compartment

14—
Transfer
Case
Shift
Lever

15—
Transmission
Shift
Lever

16—
^Heater
Controls*

17—
Accelerator
Pedal

18—
Brake
Pedal

19—
Clutch
Pedal

20—
Hand
Brake
Control

21—
Headlight
Dimmer
Switch

*On
applicable models only. solid in construction without groove.
Either

grooved and solid pad covers can be installed on

CJ-3B,
CJ-5,
CJ-5A,
CJ-6,
CJ-6A,
DJ-5 and DJ-6 models.
T-8.
Front Seat Adjustment
The
Bostrom bucket type driver's seat installed on

early
Models CJ-5, CJ-6, DJ-5 and DJ-6, are equipped with a 3-position manual adjustment.
Three
attaching
holes
are provided in the seat
support at the four seat mounting locations. To
adjust
the seat, remove the four attaching bolts,

move
the seat and four mounting spacers to the
desired
location, and reinstall the
bolts
at the new
location. Refer to Fig. T-12.

On
late models the driver's seat may be quickly ad­

justed
to the most comfortable driving position by releasing the lever located at the lower left front

edge
of the seat. Pushing the lever to the right al-
CD CD®
®@©"®^
FIG.
T-9—VEHICLE
CONTROLS
—
CJ-5,

CJ-6
DUAL
LEVER
TRANSFER
CASE

1—
Light
Switch

2—4-Way
Flasher
Switch*

3—
Hand
Throttle

4—
Choke
Control
5—
Brake
Warning
Light*

6—
Ignition-Starter
Switch

7—
Instrument
Cluster

8—
Horn
Button

9—
Qlove
Compartment

10—Heater
Controls*

•On
applicable models only.
11—
Front
Axle
Drive
Shift
Lever

12—
Transmission
Shift
Lever

13—
Aux.
Range
Shift
Lever

14—
Accelerator
Pedal
15—
Brake
Pedal
16—
Clutch
Pedal

17—
Headlight
Dimmer
Switch

18—
Hand
Brake
Control

19—
Turn
Signal
Lever
355

T

BODY
lows
the seat to be
moved forward
or
rearward.
Re­

positioning
the
lever
to the
left
will
lock
the seat
in
the
desired position.
T-9.
Passenger
Seat
Safety
Catch
Thejfront
passenger seat on
late model vehicles
is

provided
with
a
safety
catch, located
at the
left

rear
base of the seat. To
tilt
the seat
forward,
first

release
the
catch
by
pulling
upwards
on the
catch lever. 11213
.

FIG.
T-ll—CLUTCH
AND
BRAKE PEDAL
PAD

FIG.
T-10—VEHICLE CONTROLS
-
MODELS
DJ-5 AND DJ-6 1—
Light
Switch
2— Windshield Wiper Switch
3—
Hazard
Warning Light Switch
4—Hand Throttle*
5—
choke
Control
6— Windshield
Washer
Control
7— Ignition
Starter
Switch
8— Cigarette Lighter* 9—
Turn
Signal Lever
10— Instrument Cluster
11—
Horn
Button
12— Glove Compartment
13—
Heater
Controls*
14— Transmission Shift Lever
15— Accelerator
Pedal

16—
Brake
Pedal

17—
Clutch
Pedal
18—
Hand
Brake Control
19— Headlight Dimmer Switch

*On
applicable
models
only.
FIG.
T-12—EARLY MODELS
FRONT SEAT
ADJUSTMENT

1—
Location Holes
2— Spacer

S5§

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

U
DESCRIPTION
—
Continued

AXLES

W-99* Gauge — Pinion & Ring
Gear
Setting
W-104-B* Puller — Tapered Roller Bearing Removing
W-126* Driver — Pinion Bearing Cup
W-128* Installer — Differential Inner Oil Seal W-129 Spreader — Differential
Carrier
Housing
W-138* Driver & Adapter —
King
Pin Bearing
W-144* Wrench — Wheel Bearing Adjusting Nut W-147* Driver — Pinion Oil Seal W-163* Puller
—-
Axle Shaft Drive Flange
W-186* Driver — Axle Shaft Oil Seal
W-188* Driver — Differential Case Bearing W-251* Puller — Pinion Oil Seal
W-262*
Sleeve
— Pinion Bearing Installing

W-263
Semi-Floating
Rear
Axle Shaft Oil Seal W-264* Driver — Pinion Outer Bearing Cup
W-297* Torque Wrench — Pinion Bearing Adjusting W-343* Remover
85
Installer —
Rear
Axle Bearing (Flanged Axle)
W-344* Installer — Pinion Inner Bearing Cups

C-319-A
Puller —
Rear
Wheel Hub (Tapered Axle Shaft)
C-690 Checking Scale —
King
Pin Bearing Preload DD-914-P Press — Tapered Roller Bearing Removing
DD-914-9 Reducer Ring — Differential & Pinion Bearings (Use with DD-914-P)

C-3
716 Driver — Differential
Carrier
Bearing C-4142
Gear
Rotating Tool —
Trac-Lok
Differential
**Jeep*
exclusive
tool

Steering
Group

C-3646 Puller, Steering Shaft Arm

Brake
Group

W-172 Puller, Parking Brake Drum
U-12.
STflNDfiRD
AND
RECOMMENDED
TOOLS

Tool
Description
ENGINE

W-292
Tester — Cooling
System
Thermostat
C-119 Indicator — Cylinder Bore C-385 Compressor — Piston Ring
C-647 Fixture — Spring Testing
C-823
Hone
— Cylinder Bore Refinishing
C-3012 Reamer — Cylinder Ridge
C-3250 Pliers — Radiator fis Heater
Hose
Wire Clamp
C-3411
Gauge — Pressure & Vacuum
C-3422-A Compressor — E-type Valve Spring
C-3501
Hone
— Cylinder
Deglazing
C-3514
Flusher — Cooling
System

C-3886 Fixture — Carburetor Holding C-3896-A Tachometer — Portable
C-3943 Gauge — Compression Checking
C-3952 Torque Wrench, 150
lb-ft.
Swivel Head C-3953 Stand, Engine Repair
C-3959 Light — Ignition Timing
C-4065 Wrench — Oil Filter Removing
C-4080 Tester — Cooling
System
fig
Pressure Cap

ELECTRICAL

40B Hydrometer — Battery Service
W-291 Tester — Instrument
C-3674
Aimers —
Headlight
(Pair)
C-3829 Tester —
Diode
Polarity
C-3888 Tester — Volt-Ampere C-3950 Tester — 12V 60 Amp. Carbon Pile Resistor 361