check engine light JEEP DJ 1953 Manual PDF

H

ELECTRICAL
SYSTEM H-15L SERVICE
DIAGNOSIS

SYMPTOMS

Battery
Discha
rged: Shorted
Cell
in Battery......... Short in Wiring..
•
Generator Not Charging ,
Loose or Dirty Terminals
Excessive Use of Starter Excessive Use of Lights...... Insufficient Driving.........

Low
Regulator
Setting.......

Stuck
Cut-out in Regulator. ..

Low
Electrolyte
Level
in Cells

Alternator:
FAILS
TO
CHARGE:
Belt Loose Open or High Resistance in

Charging
or Ground Return
Circuit
or Battery Connections............
Excessively Worn, Open, or
Defective
Brushes.
Open Isolation
Diode.

Open Rotor (Field
Coil)

LOW
OR
UNSTEADY
CHARGING RATE:
Belt Loose.... Intermittent or High Resistance
Charging
or Ground Return
Circuit
or Battery Connections
Excessively Worn, Sticky, or Intermittent Brushes
Shorted or Open Rectifier
Diode
Grounded
or Shorted
Turns
in Rotor (Field
Coil)

Open,
Grounded, or Shorted
Turns
in
Stator

EXCESSIVE
CHARGE RATE:
Loose Connections on Alternator...........

Faulty
Regulator

NOISY
ALTERNATOR:
Defective
or Badly Worn Belt
Misaligned Belt or Pulley
Loose Pulley
Worn
Bearings.
Shorted Rectifiers

Generator:
Low
Charging Rate—
Dirty
Commutator
Poor Brush Contact.
................
Regulator Improperly Adjusted.......

High
Resistance in Charging
Circuit...
Ground
Strap Engine to Frame Broken
Loose or Dirty Terminals Slipping Generator Belt

Worn
Out Brushes

Weak
Brush Spring Tension..........

Out
of Round Commutator
PROBABLE REMEDY

Replace Battery

Check
Wiring
Circuit

Inspect Generator and Fan Belt
Clean
and Tighten

Tune
Engine

Check
Battery
Recharge Battery
Correct
Setting

Correct
Add
Distilled Water
Tighten to
Specifications
Test
and Correct
Test
Brushes and Replace if Necessary

Test
and Replace if Necessary
Test
and Replace if Necessary
Tighten to
Specifications

Test
and Correct
Test
and Replace if Necessary
Test
and Replace if Necessary

Test
and Replace if Necessary

Test
and Replace if Necessary

Check
and Correct

Check
and Correct
Replace

Align,
Replace Parts as Necessary Tighten Replace Bearings as Necessary
Test
and Replace as Necessary

Clean
Commutator
Repair
or Install New Brushes

Adjust

Clean
and Tighten Terminals Replace

Clean
and Tighten

Adjust
Belt
Install
New Brushes
Replace
Repair
220

'Jeep*
UNIVERSAL
SERIES SERVICE
MANUAL

H
H-151.
SERVICE
DIAGNOSIS—Continued

SYMPTOMS PROBABLE
REMEDY

Generator:
(continued)
Fails
To Charge-Open Charging Circuit Correct
Sticking Brushes Repair or Replace
Dirty
or Burned Commutator ... Clean Commutator
Grounded Commutator Replace
Open Circuit in Field Replace
Weak Soldering on Armature. . . Repair Grounded Wiring Repair

Defective
Regulator. .. Replace Regulator
Too High Charging Rate— Regulator Improperly Adjusted Adjust or Replace
Short in Armature Replace Grounded Field-to-regulator Wire Correct
Shorted
Cell
in Battery... Replace Battery

Starting
Motor: Slow Starter Speed— Discharged Battery or Shorted
Cell
Recharge or Repair
Ground
Strap Engine to Frame. Clean Terminals and Tighten
Loose or Dirty Terminals Clean and Tighten
Dirty
Commutator Clean with No. 00 Sandpaper

Worn
Out Brushes Install New Brushes
Weak Brush Spring Tension Replace

Worn
Bearings Replace Burned Starter Switch Contacts Replace Switch

Will
Not
Turn
Engine— Open Circuit at Starter Correct

Solenoid
Open or Stuck Replace
Solenoid
Starter Switch
Defective
Replace Switch
Starter Drive Broken or Stuck. Repair or Replace
Battery Discharged Recharge Battery

Distributor:
Hard
Starting— Distributor
Points
Burned or Pitted Clean
Points
or Replace (Adjust)

Breaker
Arm Stuck on Pivot Pin...... . ... . . . Clean and Lubricate

Breaker
Arm Spring Weak Replace

Points
Improperly Adjusted Adjust
Spark
Plug
Points
Improperly Set Adjust

Spark
Plug Wire Terminals in Distributor
Cap
Corroded Clean
Loose Terminals Check Circuit
Loose or Dirty Terminals on Ground Strap— Engine to Frame. Clean and Tighten
Condenser Faulty Replace Improper Ignition Timing Set Timing

Lights:
Burn
Dim— Loose or Dirty Terminals....... ........ Clean and Tighten
Leak
in Wires. Check Entire Circuit for Broken Insulation
Poor Switch Contact Install New Switch Poor Ground Connection Clean and Tighten

Aim
Headlamp Beams. Use Aiming
Chart
221

CLUTCH

is deeply scored or grooved, the part should be

replaced.

b. Inspect driven plate for wear or damage to fac­
ings,
loose
rivets, broken or
loose
torsion springs,

and
flattened cushion springs. If facings are worn
near
rivets or are oily, replace the plate assembly.

A
slight amount of oil on clutch facings
will
cause

clutch
grab and chatter; excessive oil on facings

will
cause slippage. It is not practical to remove
oil
with solvents or by buffing since oil
will
con­
tinue to bleed from facing material when hot. If
oil
is found on driven plate facings, examine trans­
mission drainback hole, pilot bushing,
engine
rear

main
bearing and other points of possible oil leakage. Test the fit of driven plate hub on trans­
mission main drive gear for an easy sliding fit.
c. Inspect clutch release bearing for scoring or ex­ cessive wear on front contact face. Test for rough­

ness
of balls and races by pressing and turning
front race slowly. Inspect main drive gear pilot
bushing in crankshaft. Replace bushing if it is rough or worn. Regardless of whether the old plate

or
a new plate is to be installed, check the plate
for runout. Slide the driven plate, front side first,
over the transmission main drive gear shaft so that

it
is tight on the spline. Index a
dial
indicator to the plate facing as shown in
Fig.
1-9. While holding

firmly
against front end of main drive gear, to take up play in main drive gear bearing, slowly
rotate driven plate and observe the amount of
run­

out shown by indicator. If runout of front facing
exceeds
.025" [0,635 mm.], replace the plate. It
is not practical to correct excessive runout by bending. 12769

FIG.
1-9—RUNOUT
CHECK
—
CLUTCH
PLATE
1—
Front
Facing
(Flywheel
Side)

2—
Dial
Indicator
Set
d.
Check
clutch pilot bushing for excessive wear

or
damage. Replace pilot bushing, if necessary, with

special
removal and installation
tools.
(See
Figs.

1-6 and 1-7). 1-13.
SERVICING
CLUTCH
PRESSURE
PLATE
AND

DISC
—
BORG
&
BECK
V6
(Late
Models)

The
Borg & Beck clutch is a single plate, dry disk
type. It provides smooth
engagement
of
engine
power to the wheels. The clutch consists of a pres­

sure
plate assembly with pressure springs and
release levers, and driven plate assembly. The
driven
plate assembly
uses
spring center vibration
neutralizes and two flexible facings.

The
clutch driven plate is spring cushioned with a facing riveted to both sides. The coil springs around
the hub absorb the power shocks and cushion the

driving
mechanism. The clutch throw-out bearing is of the
ball
type, packed at time of manufacture,

and
requires no further lubrication.
No adjustment for wear is provided in the clutch itself. An individual adjustment is built into the
clutch
cover to adjust the height of the release
levers.
This
adjusting nut is locked in position

and
should never be disturbed unless the clutch assembly has been disassembled for the replace­
ment of worn parts or to correct the height of the release levers.

When
the clutch pedal is depressed (disengaged),
the release bearing is moved toward the flywheel
and
contacts the inner ends of the release levers.

Each
lever is pivoted on a floating pin which re­
mains stationary in the lever and rolls across a short flat portion of the enlarged
hole
in the eye-
bolt. The outer ends of the
eyebolts
extend
through
holes
in the stamped cover and are fitted

with
adjusting nuts to secure the levers in the
correct
position. The outer ends of the release levers

engage
the pressure plate lugs by means of ful-
crums,
which provide knife-edge contact
between

the outer ends of the levers and the lugs as shown
in
Fig.
I-10. 12190

FIG.
MO—CLUTCH
LEVER
POSITIONS
A—Clutch
Engaged
B—Clutch
Disengaged 1-14.
Clutch
Pressure Plate Adjustment

The
clutch pressure plate adjustment must be
checked before installing a new or reconditioned

clutch.
The proper spacer thickness and
gage
length for a particular clutch is listed in Par. 1-30.
Use
Clutch
Adjusting
Fixture
W-296. If the W-296
fixture is not available one can be fabricated as
described in Par. 1-26. 230

CLUTCH

FIG.
1-14—LIFTING
LEVER
AND
EYEBOLT FROM PRESSURE PLATE
1—
Lever

2—
Eyebolt

3—
Fulcrum
A Pressure Plate
lever and the upper end of the
eyebolt
are as
near
together
as possible. Keep the
eyebolt
pin seated in its socket in the lever as shown in Fig.
1-13.
Lift
the fulcrum over the ridge on the end of the lever.
Lift
the lever and
eyebolt
off the
pressure plate as shown in Fig. 1-14.
1-19.
Inspect
Pressure Plate and Disc
Inspect the pressure plate to make sure that it is not cracked or scored.
Check
on a surface plate
for a warped condition, as a pressure plate out of alignment
will
result in clutch chatter.
Machin­

ing or grinding the face of a warped pressure
plate is not recommended. If a warped condition
exists, replace the pressure plate. A new plate
should be installed if the plate or cushion springs appear to be defective. The cushion springs must
not be bent out of shape or flattened.

The
clutch discs for the nine or twelve spring clutches are designed for operation with their
respective clutches. Difference in general appear­ ance of the discs may be noted in the method of
housing the six torque dampening springs and in the
hub design.

After
removal of the clutch assembly, the disc should be inspected. The presence of grease or oil
on the friction facing can cause the clutch to chatter

and
grab during
engagement
and slip at higher speeds. If this condition is evident, the facings or
disc should be replaced and the cause of oil ac­
cumulation corrected. Excessively worn facings
should be replaced. The clutch disc must be in­ stalled with the long end of the hub toward the

transmission.
1-20.
Inspect Transmission Clutch
Shaft

Slide
the clutch driven plate
onto
the transmission

clutch
shaft to make sure that it is free on the
splines. If the splines on the transmission clutch
shaft are
burred,
remove the
burrs
with a fine file or
stone.
If the movement of the clutch driven
plate is not free on the splines, the result
will
be
clutch
drag and
hard
shifting of transmission gears.
1-21.
CLUTCH
PRESSURE
PLATE ASSEMBLY AND
ADJUSTMENT

1-22. Assemble
Clutch
Levers

Prior
to assembly, apply a small amount of petro­

latum
to each slide of the pressure plate lug.

a.
Lay the pressure plate on the block in the
press.
b. Assemble a lever,
eyebolt,
and pin holding the
lever and
eyebolt
as
close
together
as possible.

With
the other hand, grasp the fulcrum as shown
in
Fig. 1-15.

c.
Insert the fulcrum in the
slots
of the pressure
plate lug.
Lower
slightly and tilt the lower
edge

until
it touches the vertical milled surface of the
lug.
Insert the lower end of the
eyebolt
in the

hole
in the pressure plate. The short end of the lever
will
then be under the hook of the lug and

near
the fulcrum.

d.
Slide the fulcrum upward in the
slots
of the

lug.
Lift
it over the ridge on the short end of the
lever and drop it into the
groove
in the lever
(Fig.
1-15).
1-23.
Assemble
Clutch
Spring and
Cover

a.
After all levers are installed, place the felt grease pads over the eyebolts.
Lubricate
pads

sparingly
with light
engine
oil.
Then
place the
clutch
pressure springs in a vertical position on
the spring
bosses.
FIG.
1-15—INSTALLING
CLUTCH LEVERS

1—
Lover

2—
Eyebolt

3—
Fulcrum

4—
Pressure
Plate
232

THREE-SPEED
TRANSMISSION

FIG.
J-l—TRANSMISSION

REMOTE
CONTROL
CJ-5
A,
CJ-6A

1— Stop Screw
2—
Bias
Spring

3—
Gearshift
Lever
4—
Lever
Ball

5—
Steering
Wheel 6—
Horn
Button 7—
Column
and Bearing
8—
End
Huts
9—
Shift
Rod
Ends

10—
Shift
Rod
11—
Shift
Rod
12—
Cross-Shift
Bracket

13—
Control
Shaft
14—
Lubrication
Fitting
15—
Lever
and
Clutch

16—
Adjusting
Yoke

17—
Aligning
Rod 11706

b.
Remove gearshift lever fulcrum pin and the
gearshift lever.

c.
Remove plates on the toe board at the steer­
ing
post.

d.
Remove two screws holding remote control
housing to the steering
post
and lift the housing
from
the positioning pin.

e.
Remove the assembly down through the floor
pan.

f. Remove the lower clutch and shift lever from the housing by turning counterclockwise.
g. Remove upper clutch and shift lever in the same

manner.

h. Wash all parts in a suitable cleaning solution.

J-5.
Reassembly of
Remote
Control
•
Refer to
Fig.
J-l

Check
clearance of shift dog which
engages
in slot
of clutches, and if found to be greater than .009" [0,229 mm.] clearance, replace the worn parts.
Assemble upper clutch lever assembly in housing
making
sure that the alignment
hole
in the housing
faces toward the engine.
Turn
the upper lever as­
sembly in as far as it
will
go and then back off one

full
turn
until the
hole
in the clutch lever aligns

with
hole
in the housing.
Assemble the lower clutch lever assembly in hous­ ing until faces of clutches contact then back off
not more than one-half
turn
which should bring
the aligning
hole
in the lever in line with the
hole
in
the housing. If the one-half
turn
does
not bring
the alignment
hole
in proper position, it
will
be
necessary to grind off (square with axis not to exceed .015") [0,397 mm.] the face of the lower

clutch;
in other words, backing off not more than
one-half
turn
from face to face contact
gives
the

proper
clearance of .015" to .031"
[0,397-0,794
mm.]

between
the two clutches.
Assemble the unit to the steering
post
in reverse

order
of dismantling and adjust remote control

rods.
After
assembly, if the shift dog catches on the
edge

of the slot in the clutch when moving the lever up

and
down, disconnect the shift rod at the
transmission
end and either lengthen or shorten it
slightly to correct this condition.

J-6.
TRANSMISSION
REMOVAL
The
following repair procedures given in Par. J-7
through J-ll for the standard
3-speed
transmission
apply
in general to all models listed. Minor dif­
ferences
between
models that affect the procedure

are
noted. Procedure for the optional
4-speed
trans­mission
begins
with Section
J-l.

Removal
is as follows:

a.
Drain
the transmission and transfer case. Re­ place the
drain
plugs.

b.
Remove the floor pan inspection plate.

c.
Remove the shift lever and shift housing as­ sembly and its gasket from the transmission. On 240

L

PROPELLER
SHAFTS
AND
UNIVERSAL JOINTS

move
the snap rings, pinch the ends
together
with

a
pair
of pliers. If the rings do not readily snap
out of the groove, tap the end of the bearing lightly
which
will
relieve pressure against the rings.
After
removing the snap rings, press on the end of
one bearing until the
opposite
bearing is pushed
from
the yoke arm.
Turn
the joint over and press
the first bearing back out of that arm by pressing
on the
exposed
end of the
journal
shaft. Use a
soft
ground drift with a flat face about [0,8 mm.]

smaller
in diameter than the
hole
in the yoke arm
and
drive it out, otherwise there is danger of damag­ing the bearing.

Repeat
this operation for the other two bearings,
then lift out
journal
assembly by sliding it to one
side.

L-4.
Snap
Ring
Type Assembly

Wash
all parts in cleaning solvent and inspect the
parte
after cleaning. Replace any parts that indicate
extensive
wear.
It is advisable to install new gaskets
on the
journal
assembly regardless of the condition of the old gaskets. Make certain that the grease

channel
in each
journal
trunnion is open.

Pack
the bearing
cones
one-third
full
of lubricant
and
install the rollers.
Draw
the bearings into the end yoke arm and seat
them firmly against the bearing shoulders. Hold
the bearings in a vertical position to prevent the
needles
from dropping out until the joint is as­ sembled. If the joint binds when assembled, tap
the arms lightly to relieve any pressure on the bear­
ings at the end of the
journal.

L-5.
U-Bolt
Type Disassembly

Removal
of the attaching "U"-bolt releases one set
of bearing races. Slide the propeller shaft into the
yoke flange to remove them using care not to
lose
the rollers.
After
the removal of the one set of bearing races,
release the other set by removing the snap rings

in
the
sleeve
yoke by pinching the ends
together

with
a
pair
of pliers. Should the rings
fail
to snap
readily
from the groove, tap the end of the bearing
lightly,
which
will
relieve the pressure against them.

Press
on the end of one bearing, until the
opposite
bearing
is pushed out of the yoke arm.
Turn
the

universal
joint over and press the first bearing out
by pressing on the
exposed
end of the
journal
as­
sembly. Use a
soft
ground drift with a flat face about
\{i
[0,8 mm.] smaller in diameter than the
hole
in the yoke
arm
and drive out the bearing.
Lift

the
journal
out by sliding to one side.
Clean
all
parts
and check for wear.

L-6.
U-Bolt Type Assembly

Wash
all parts in cleaning solvent and inspect the
parts
after cleaning. Replace any parts that indicate
extensive
wear.
It is advisable to install new gaskets
on the
journal
assembly regardless of the condition
of the old gaskets. Make certain that the grease
channel
in each
journal
trunnion is open.

Pack
the bearing
cones
one-third
full
of lubricant
and
install the rollers.
Draw
the bearings into the end yoke arm and seat
them firmly against the bearing shoulders. Hold the
bearings in a vertical position to prevent the
needles
from dropping out until the joint is as­
sembled. If the joint binds when assembled, tap the arms lightly to relieve any pressure on the
bearings at the end of the
journal.
Tighten the
U-bolts equally. U-bolt torque wrench reading is 15 to 20 lb-ft. [2,07 a 2,76 kg-m.].

When
installing the assembly in the vehicle be sure
that the arrows on the propeller shaft and yoke

sleeve
are in alignment as shown in Fig. L-2, or
that the unmarked joints are aligned with the yokes in the same parallel plane.

SPECIFICATIONS

L-7.
PROPELLER
SHAFTS
AND
UNIVERSAL JOINTS
PROPELLER
SHAFTS:

Make
SPICER

Dimensions:

F4
Engine Vehicles:
CJ-5,
CJ-5
A
— 3 Speed.
......
4 Speed

CJ-6,
CJ-6A
— 3 Speed 4 Speed

CJ-3B
DJ-5
DJ-6.
V-6
Engine Vehicles:
CJ-5,
CJ-5A
— 3 Speed.

CJ-6,
CJ-6A
— 3 Speed.

CJ-5
— 4 Speed
Front

Rear

Dimensions:

F4
Engine Vehicles:
CJ-5,
CJ-5
A
— 3 Speed.
......
4 Speed

CJ-6,
CJ-6A
— 3 Speed 4 Speed

CJ-3B
DJ-5
DJ-6.
V-6
Engine Vehicles:
CJ-5,
CJ-5A
— 3 Speed.

CJ-6,
CJ-6A
— 3 Speed.

CJ-5
— 4 Speed
O.D.

Length

O.D.
Length

Dimensions:

F4
Engine Vehicles:
CJ-5,
CJ-5
A
— 3 Speed.
......
4 Speed

CJ-6,
CJ-6A
— 3 Speed 4 Speed

CJ-3B
DJ-5
DJ-6.
V-6
Engine Vehicles:
CJ-5,
CJ-5A
— 3 Speed.

CJ-6,
CJ-6A
— 3 Speed.

CJ-5
— 4 Speed
1M"
[3,175 cm.]

1M*
[3,175 cm.]

\W
[3,175 cm.]
1M*
[3,175 cm.] [3,175 cm.]

\W
[3,175 cm.]

\W
[3,175 cm.] [3,175 cm.] 22^" [57,78 cm.]

28H"
[72,39 cm.]
22M*
[57,78 cm.]

mW
[72,39 cm.]

33He"
[85,57 cm.]

21W
[55,25 cm.]
21%"
[55,25 cm.]

2&*<if
[68,10
cm.]
IK"
[4,45 cm.]

1M#
[4,45 cm.]

\%"
[4,45 cm.]

\%"
[4, 45cm.]

IW
[4,45 cm.]

1M*
[4,45 cm.]

3*
[7,62 cm.]
2" [5,08 cm.]
2" [5,08 cm.]
l%" [4,45 cm.]
182£"
[45,95 cm.]
WW
[34,131
cm.]

3SJ4*
[97,79 cm.]

33%"
[84,69 cm.] 19546*
[50,64
cm.]
24^"
[61,60
cm.]

44M*
[112,40
cm.]

19%?
[50,64
cm.] 39* [99,06 cm.]

U%"
[37,47 cm.l

UNIVERSAL
JOINTS:
Make
Spicer

Cardan
Cross
Antifriction

Type
Spicer

Cardan
Cross
Antifriction

Bearing
Spicer

Cardan
Cross
Antifriction

276

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

U
DESCRIPTION
—
Continued

AXLES

W-99* Gauge — Pinion & Ring
Gear
Setting
W-104-B* Puller — Tapered Roller Bearing Removing
W-126* Driver — Pinion Bearing Cup
W-128* Installer — Differential Inner Oil Seal W-129 Spreader — Differential
Carrier
Housing
W-138* Driver & Adapter —
King
Pin Bearing
W-144* Wrench — Wheel Bearing Adjusting Nut W-147* Driver — Pinion Oil Seal W-163* Puller
—-
Axle Shaft Drive Flange
W-186* Driver — Axle Shaft Oil Seal
W-188* Driver — Differential Case Bearing W-251* Puller — Pinion Oil Seal
W-262*
Sleeve
— Pinion Bearing Installing

W-263
Semi-Floating
Rear
Axle Shaft Oil Seal W-264* Driver — Pinion Outer Bearing Cup
W-297* Torque Wrench — Pinion Bearing Adjusting W-343* Remover
85
Installer —
Rear
Axle Bearing (Flanged Axle)
W-344* Installer — Pinion Inner Bearing Cups

C-319-A
Puller —
Rear
Wheel Hub (Tapered Axle Shaft)
C-690 Checking Scale —
King
Pin Bearing Preload DD-914-P Press — Tapered Roller Bearing Removing
DD-914-9 Reducer Ring — Differential & Pinion Bearings (Use with DD-914-P)

C-3
716 Driver — Differential
Carrier
Bearing C-4142
Gear
Rotating Tool —
Trac-Lok
Differential
**Jeep*
exclusive
tool

Steering
Group

C-3646 Puller, Steering Shaft Arm

Brake
Group

W-172 Puller, Parking Brake Drum
U-12.
STflNDfiRD
AND
RECOMMENDED
TOOLS

Tool
Description
ENGINE

W-292
Tester — Cooling
System
Thermostat
C-119 Indicator — Cylinder Bore C-385 Compressor — Piston Ring
C-647 Fixture — Spring Testing
C-823
Hone
— Cylinder Bore Refinishing
C-3012 Reamer — Cylinder Ridge
C-3250 Pliers — Radiator fis Heater
Hose
Wire Clamp
C-3411
Gauge — Pressure & Vacuum
C-3422-A Compressor — E-type Valve Spring
C-3501
Hone
— Cylinder
Deglazing
C-3514
Flusher — Cooling
System

C-3886 Fixture — Carburetor Holding C-3896-A Tachometer — Portable
C-3943 Gauge — Compression Checking
C-3952 Torque Wrench, 150
lb-ft.
Swivel Head C-3953 Stand, Engine Repair
C-3959 Light — Ignition Timing
C-4065 Wrench — Oil Filter Removing
C-4080 Tester — Cooling
System
fig
Pressure Cap

ELECTRICAL

40B Hydrometer — Battery Service
W-291 Tester — Instrument
C-3674
Aimers —
Headlight
(Pair)
C-3829 Tester —
Diode
Polarity
C-3888 Tester — Volt-Ampere C-3950 Tester — 12V 60 Amp. Carbon Pile Resistor 361

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

ALPHABETICAL INDEX

SUBJECT PAR.
SUBJECT
PAR.

Abbreviations,
List
U-17 Accelerator Linkage E-70
Air
Cleaner B-25, B-26, B-82, C-21, E-69

Air
Delivery Manifold Fl-4, F2-12
Air
Filter, Pump • F2-3, F2-11

Air
Injection Tubes Fl-5, F2-13
Air
Pump Fl-2, F2-10
Alternator Bearings B-76, H-80
Alternator Brushes H-74, H-75
Alternator Charging System •
•
H-63
Alternator
Diodes
H-69, H-85
Alternator Precautions H-64 Alternator Rotor H-76, H-79
Alternator Tests H-67, H-77 Alternator Specifications H-l 52
Alternator Stator H-84
Anti-Backfire
Valve Fl-6, F2-14
Antifreeze
Chart
• G-22 Antifreeze
Solutions
- G-16
Axle Camber O-l
Axle Caster 0-8

Back-Up
Lights H-135

Ballast
Resistor. H-32 Battery C-3, H-2 Bendix Folo-Thru Drive H-105, H-106
Bleeding Brakes P-7
Body T-l Body Lubrication. B-65 Body Name Plates ' A-7

Brake
Adjustment P-14
Brake
Drums. • .P-17

Brake
Hoses
P-8

Brake
Maintenance . P-5
Brake
Master Cylinder B-40, P-2, P-20

Brake
Service P-6
Brake
Wheel Cylinder • P-21

Camber
Adjustment 0-7
Camshaft D-6, D-51, D-52, D-53, D-81, Dl-26, Dl-33, Dl-55, Dl-80

Carburetor
E-10, E-25

Carburetor
Adjustment C-25, E-14, E-40,
Fl-13,
F2-16
Carburetor
Specifications .Fl-38, F2-34, E-79

Caster
Adjustment 0-8

Charging
System Service. .H-34, H-63

Chassis
Lubrication B-7, B-83

Chassis
Torque Specifications U-14

Clutch
1-4, MO
Clutch
Adjustment 1-3
Clutch
Linkage B-44, 1-3

Clutch
Maintenance .. 1-2
Clutch
Release Bearing B-74, 1-25

Coil
C-20, H-19, H-31 Connecting Rod Bearings D-47, D-48, D-49, Dl-49 Connecting Rod
Crank
Pins D-42
Connecting Rods... .D-20, D-50, D-95, Dl-31, Dl-45, Dl-75
Controls B-59, B-62
Cooling System B-28, G-l Cooling System Filling G-2

Core
Hole Expansion Plugs D-72

Crankcase
Ventilating System B-13, C-6, D-110

Crankshaft
D-26, D-38, D-39, Dl-38, Dl-73
Crankshaft
End Play. D-83, Dl-74

Crankshaft
Main Bearing D-43, D-44, Dl-32, Dl-40, Dl-73

Crankshaft
Oil Seal, Front Dl-21, Dl-85
Crankshaft
Oil Seal, Rear D-63, D-85, Dl-72

Cylinder
Block D-32, Dl-34

Cylinder
Bores D-35, Dl-36

Cylinder
Head D-17, D-73, D-98, Dl-24, Dl-63, Dl-82

Cylinder
Head Torque. C-5
Dash Pot Adjustment C-26, E-44
Differential B-51 thru B-53, N-9 Differential Adjustments N-16, N-18
Differential, Powr-Lok N-20
Differential,
Trac-Lok
N-24
Directional Signal Lights. . H-138
Distributor B-14, B-15, C-10, D-13, Dl-9, H-9, H-20 Distributor Check H-l7, H-28
Distributor Point Dwell C-17 Distributor Resistance Test C-16

Drawbar
.R-6, U-16
Dual
Brake System P-l thru P-26

Electrical
Instruments H-l22

Electrical
Specifications .H-l52

Electrical
System H-l Engine .
..D-l,
Dl-1
Engine Code Number A-6
Engine Compression .
.
C-9 Engine Disassembly . • .D-6, Dl-5 Engine Installation D-105, Dl-102
Engine Lubrication System B-4, B-6 Engine Mountings D-3, Dl-3
Engine Oil B-9
Engine Oil Filter B-10, B-ll,
D-lll,
Dl-13, Dl-93
Engine Oil Pan D-l9, D-66, D-97, Dl-29, Dl-51, Dl-77 Engine Oil Pump. . .D-14, D-65, D-93, Dl-19, Dl-50, Dl-87
Engine Overheating. G-l9 Engine Removal D-5, Dl-4.

Exhaust
Emission Control — F4 Fl-1 thru Fl-30
Exhaust
Emission Control — V6 F2-1 thru F2-36
Exhaust
Manifold, Install F-6

Exhaust
Pipe -
•
F-8

Exhaust
System F-2, F-3

Exhaust
System Maintenance F-4

Fan
Belt C-27, Dl-11, Dl-96, G-18
Floating Oil Intake. D-64, Dl-30, Dl-50, Dl-76 Flywheel D-25, D-67, D-87, Dl-28, Dl-52, Dl-78
Flywheel Housing. D-71, D-88, Dl-27, Dl-54, Dl-79
Flywheel Pilot Bushing D-70, 1-8

Frame
R-l

Frame
Alignment. R-2
Frame
Dimensions R-3
Frame
Straightening R-4

Front
Bumper Weight. • U-9
Front
Axle B-50, M-2

Front
Axle Alignment R-5

Front
Axle Installation • M-12
Front
Axle Maintenance M-3

Front
Axle Shaft Removal M-5

Front
Axle U-Joint B-54, B-55, M-7

Front
Axle Steering Knuckle M-&

Front
Wheel Alignment 0-4

Front
Wheel Bearings B-56, B-57, Q-4
Front
Wheel Toe-in 0-5, 0-6

Front
Wheel Turning Angle 0-9
Fuel
Gauge Float Unit F-76

Fuel
Lines - E-77

Fuel
Pump E-45, E-54, E-60, E-67
Fuel
Pump Check C-23

Fuel
Tank
E-72

G

Gauges, Testing H-l24

General
Specifications A-8
Generator B-16, H-34 thru H-40

Glass
Replacement • T-4
Governor. . .
•.
• U-3
Guides, Valve D"61

H

Hazard
Warning Lights H-139
Head Lamp Aiming H-131, H-132 Head Lamp Replacement H-130
Headlight Dimmer Switch H-l
2
7

Heat Control Valve C-7, F-7 Heated Air System • •
•
F2-2
Heater U-10
Horns.....
....H-137 371

ALPHABETICAL
INDEX

SUBJECT
PAR.

SUBJECT
PAR.

Ignition Cable Test C-l9 Ignition
Coil
C-20, H-19, H-31
Ignition Switch H-89 Ignition System H-3
Ignition
Timing
C-14, H-18, H-30 Ignition Wires C-18
Intake Manifold '." Dl-7, Dl-101
Instrument, Electrical H-122

L

License Plate Light H-l36
Lighting
System H-l25

Light
Switch, Main . H-l 26

Lubrication
B-l
Lubrication,
Body B-65

Lubrication
Maintenance Schedule B-8
Lubrication
of Optional Equipment B-69

Lubrication,
Off Highway B-79

Lubrication,
Special. B-2

M

Main
Bearings D-43, D-82, Dl-32, Dl-42, Dl-73

Main
Light Switch. H-l26
Maintenance, Clutch 1-2 Maintenance, Exhaust System.,
-
F-4
Manifold, Exhaust -F-6 Manifold, Intake D-7, Dl-101
Manifold Vacuum Check. .C-24 Master Cylinder, Brake B-40, P-2, P-20
Miscellaneous Data U-16 Mountings, Engine • • •
-
D-3, Dl-3
Muffler. F-9

O
Oil
Filter B-10, B-ll,
D-lll,
Dl-13, Dl-93

Oil
Pan D-19, D-66, D-97, Dl-29, Dl-51, Dl-77
Oil
Pump. D-14, D-65, D-93, Dl-19, Dl-50, Dl-87

P

Paint and
Trim
Plate • • A-7

Parking
Brake Adjustment P-ll
Parking
Lights H-133
Pilot Bushing, Crankshaft D-70, 1-8
Pintle Hook U-7
Pistons D-20, D-95, Dl-31, Dl-48, Dl-75 Piston Rings. • • •
•
D-37, Dl-47 Positive Crankcase Vent. B-13, C-6, D-110

Powr-Lok
Differential B-72, N-20
Primary
Circuit,
Electrical H-4 Propeller Shaft U-Joints .B-58, L-2, L-3 Propeller Shaft Specifications <:' L-7

R

Radiator
B-28, B-29, G-5

Radiator
Hoses. G-7

Radiator
Pressure Cap G-4

Rear
Axle. B-50, B-51, B-52, N-9

Rear
Axle Reassembly • N-l
7
Rear
Axle Disassembly N-l
2

Rear
Axle Pinion Adjustment N-l6

Rear
Axle Shaft N-2, N-3

Rear
Bearing Seal, Crankshaft D-63, D-85, Dl-62

Rear
Wheel Bearings B-56, B-57, N-4, Q-3
Regulator Test, Voltage H-47, H-71
Rocker
Arm Cover.. . Dl-65

Rocker
Arms D-16, D-74, D-99, Dl-60 Rotor, Alternator H-76, H-79

S

Seats
• T-8 Secondary
Circuit,
Electrical H-5
Shock Absorbers B-48, S-7
Solenoid Switch. H-l21 Special Lubricants B-2
Spark
Plugs C-4, H-33
Special Tools • U-ll

Speedometer
Cable B-60 Springs B-77, S-4, S-5

Spring
Bushings S-2

Spring
Pivot Bolts S-3

Spring
Shackles S^2

Spring
Specifications S-8 372 Starting Motor B-18, H-92, H-108
Starting Motor Bearings B-75
Starting Motor Bendix Drive H-105, H-106
Starting System H-7, H-88
Starting System Maintenance H-93 Stator, Alternator H-84
Steering • • •
•
O-l
Steering Arm P-10
Steering Column Adjustments 0-4
Steering Column and Wheel Service O-20 Steering Gear. . B-27, 0-22
Steering Gear Adjustment 0-5
Steering Gear Function 0-2
Steering Knuckle. B-27, M-8 Steering Linkage 0-14

Stop
Light Switch H-128
Switch, Heater U-10 Switch, Ignition H-89
Switch, Wiper Motor H-142

T

Tail
Light . H-134

Tail
Pipe F-10 Temperature Sending Unit G-10
Thermostat G-9
Timing
Chain Dl-22, Dl-66, Dl-84
Timing
Chain Cover Dl-20, Dl-67, Dl-86
Timing
Gears D-22, D-54, Dl-22, Dl-66, Dl-84

Timing,
Ignition. C-14, H-18, H-30

Tire
Service . •
•
Q-l
1

Toe-in Adjust 0-7, 0-8 Tools, Special. . .
........
U-ll Torque Specifications, Chassis U-14
Torque Specifications, Engine .U-13

Top,
Canvas. T-5

Trac-Lok
Differential N-24
Transfer
Case B-36, K-1
Transfer
Case Reassembly K-6

Transfer
Case Disassembly K-3

Transfer
Case Linkage - K-8

Transfer
Case Removal K-2 Transmission and Transfer Case. B-30, J-7 Transmission —
3-Speed
B-37, B-38, J-l
Transmission —
4-Speed
... J-20
Transmission Brake P-4 Transmission Brake Adjustment P-l
2

Transmission,
Cane Shift .J-8 thru J-19

Transmission,
Remote Shift J-4
Transmission Remote Shift Adjustment J-3
Transmission Specifications
-
J-27
Tune-Up
Sequence
C-2

Tune-Up
Specifications C-30

U

U-Joint, Front Axle . . B-54, B-55, M-7
U-Joint, Propeller Shaft B-58, L-l

Vacuum
C-24 Valves D-21, D-56, D-90, Dl-56, Dl-63

Valve
Adjustment D-107

Valve
Lifter Dl-57, Dl-81

Valve
Seats
D-59

Valve
Springs .D-56, D-90, Dl-63

Valve
Tappets C-8, D-29, D-62, D-80
Valve
Timing D-109
Vehicle Description A-2
Vehicle Identification A-3
Vehicle Serial Number. A-5

Vibration
Damper D-l2, D-96, Dl-17, Dl-70 Voltage Regulator. H-41, H-71

W

Water Pump G-ll thru G-15
Water Pump Bearings B-74
Wheels Q-l
Wheel Balancing Q-2 Wheel Bearing Adjustment Q-5, Q-6, Q-7
Wheel Brake Service P-6 Wheel Bearing Service Q-3
Wheel Cylinder, Brake P-21 Windshield T-3 Windshield Wiper Motor . .H-142

SM-1046
PRINTED
IN U.S.A.
110-CH6M