mileage JEEP DJ 1953 Service Manual

B
LUBRICATION B-3.
SERVICE
MAINTENANCE
SCHEDULE

Perform
the following operations at the mileage shown. Two thousand miles equals
3,200
km.

SERVICE
MAINTENANCE
SCHEDULE

OPERATION
VEHICLE
^ n>
MILEAGE
IN
THOUSANDS

6 8 10 12 24 30
Check Wheel Nut Torque*
Check
Fluid
Level
in Battery X Check
Fluid
Level
in Brake Master Cylinder0. X
Service
Cooling
System X Service Tires X

Lubricate
Distributor
Cam Lubricator (F4-134) X
Lubricate
Steering Linkage X

Lubricate
Propeller Shaft Universal Joints X

Lubricate
Propeller Shaft
Slip
Joints ; X
Lubricate
Tie Rod and Drag
Link
Sockets................................... X Change Engine
Oil
and
Filter,
and Service Air Cleaner (F4 134 Engine)** X
Change Engine Oil and
Filter,
and Service Air Cleaner (V6-225 Engine)**....
Check Brake Operation and Pedal
Free
Play X Check
Clutch
Pedal
Free
Play. .... X
Check all
V-Belt
Tensions X
Check Exhaust Emission System
(If
so equipped)*** \ X
Service Positive
Crankcase
Vent
Valve
and Breather . .' X
Road Test
Including
a Check of all Instrument
Lights
and Controls X Tune-up Engine
Check Operation of
Manifold
Heat
Control
Valve

Clean
Exterior of Radiator

Align
Headlights • Check Brake
Linings
,
Check Exhaust System for Leaks Replace Canister Air
Filter
(F. E. E. C. System)
Check
Axle
U-Bolt
Torque. Check Lubricaunt
Level
of Front
Axle
Universal Joints
Check Shock Absorber Mountings and Bushings Check Front and
Rear
Spring Bushings

Lubricate
Distributor
(V6-225).
Replace Spark, Plugs
Check Charging and Starting Circuits
Lubricate
Tailgate Latch, Supports and Hinges.

Lubricate
Door and
Hood
Hinge Pivots ;
Lubricate
Glove Compartment Door Latch

Lubricate
Heater Controls •

Lubricate
Windshield
Wiper and Washer Controls
Clean,
Repack and
Adjust
Wheel Bearings
Change Transmission and Transfer Lubricant. .
Replace
Dry-Type
Air Cleaner • Check Lubricant
Level
of
Differential

Lubricate
Transfer
Case
Shift
LeArer
Control
C«se.
. , . . . . . . . .
Continuing
each
2,000 miles

Continuing
each
6,000 miles

Continuing
each
24,000 miles

X
Continuing
each
30,000 miles
•Check after the
first
200 miles [320
km.
J
of operation.
If
wheel or wheels are changed for any
reason,
have
wheel nut torque rechecked after an additional two hundred miles of operation
••Service mileage shown or every 60 days, whichever occurs
first.

•••Maintenance check on emission system must be performed per
information
in this manual. "See text for brakes.

"Nj
^Miles
2,000
6,000
12,000
18,000
24,000
30,000
Kilometers

3,200
9,600
19,200
28,800
38,400 48,000

B-9.
Engine Oil

For
maximum
engine
protection under all driving conditions encountered during the recommended

oil
change intervals, it is necessary to use only

"MS"
certified
sequence-tested
oils. The term
"MS"
must appear on the oil container singly or

in
conjunction with other designations. "MS" des­
ignated oils are heavy-duty detergent oils that are
formulated to withstand all service conditions in
modern powerplants. Engine oils designated only
as
"ML"
and/or
"MM"
are not recommended and should not be used except in an emergency when

"MS"
oil is not available. Certified
sequence-tested

engine
oils are described on their containers by

such
phrases as:
meets,
exceeds,
excels, or has
proven superior in the
test
requirements,
test
sequences, MS Service
tests,
standards, and service

requirements,
of automotive manufacturers, auto­
makers,
or car manufacturers for MS service or
Service
MS.
It
may be necessary to change
engine
oil more
frequently than normally recommended, depending upon the type and quality of oil used, the severity
of operation conditions, if the
engine
is used for
short
periods in cold weather, or if the
engine
is allowed to idle for excessive periods.

Always
drain
the crankcase while the
engine
is hot since
dirt
and contaminants are then more
likely
to be held in suspension and therefore
will

drain
out more completely.
Drain
the crankcase as follows:

a.
Position the
drain
receptacle under the
drain

plug.

b.
Remove the
drain
plug using the correct size

wrench.
Be careful of hot oil.
c.
Carefully
clean the
drain
plug. Inspect and

replace
the gasket, if deteriorated.
d.
When the oil has drained, replace and tighten
the crankcase
drain
plug. 12

'Jeep*
UNIVERSAL
SERIES SERVICE
MANUAL

Dl

12713

FIG.
Dl-11—MEASURING
TELESCOPE GAUGE
1—
Telescope
Gauge
2—
Micrometer

may
be measured with an inside micrometer or
by setting the cylinder
gauge
dial
at zero and meas­
uring
across the
gauge
contact points with an out­side micrometer while the
gauge
is at same zero
setting. Refer to
Figs.
Dl-10 and Dl-11.

b.
If a cylinder bore is moderately rough or slightly

scored,
but is not out-of-round or tapered, it is

usually
possible to remedy the situation by honing
the bore to fit a standard service piston, since
standard
service pistons are high-limit production
pistons. If cylinder bore is very rough or deeply
scored,
it may be necessary to rebore the cylinder
to fit an oversize piston in order to ensure satisfac­
tory
results.

c.
If cylinder bore is tapered .005" [0,127 mm.]

or
more or is out-of-round .003" [0,076 mm.] or

more,
it is advisable to rebore for the smallest possible oversize piston and rings.

d.
Carefully
inspect the cylinder block for small

cracks
or fractures, and for porosity.
Rust
in any
cylinder
bore may indicate a leak.

e.
Inspect all machined surfaces for scoring and

burrs.
With
a straight
edge
and feeler
gauge,
check
each
machined surface for distortion.

D1-37.
Cylinder Block Repair
If
one or more cylinder bores are rough, scored, or

worn
beyond prescribed limits, it
will
be necessary
to correct bores and fit new pistons.

If
relatively few bores require correction, it
will

not be necessary to rebore all cylinders to the same
oversize in order to maintain
engine
balance, since
all
oversize pistons are held to the same weights as

standard-size
pistons. If conditions justify replace­
ment of all pistons, however, all new pistons should
be the same nominal size.

Standard-size
service pistons are high-limit, or

maximum
diameter; therefore, they can usually be installed after a slight amount of honing has
been
done
to correct slight scoring or excessive

clearances.
This
applies
primarily
to
engines
which
have relatively low mileage. Service pistons are also furnished in .010"
[0,254
mm.] oversize. All

service
pistons are diamond bored, and selectively
fitted with piston pins; pistons are not furnished
without pins.

Caution:
Do not attempt to cut down oversize pis­

tons
to fit cylinder bores as this
will
destroy the

surface
treatment and affect the weight. The small­
est possible oversize service pistons should be used

and
the cylinder bores should be honed to size

for
proper clearance.

Before
honing or reboring cylinders, measure all new pistons with a micrometer, on an axis perpen­

dicular
to the piston pin. Select the smallest piston

for
the first fitting. The slight variation usually
found between pistons in a set may provide for
correction
in case the first piston tried is too

small.

If
wear at top of cylinder
does
not exceed .005" [0,127 mm.]
excess
diameter, or exceed .003"
[0,076 mm.] out-of-round, honing is recommended.

If
wear or out-of-round
exceeds
these
limits, the
bore should be reground with a boring bar of the

fly
cutter type, then finish-honed.

When
reboring cylinders, all crankshaft bearing caps must be in place and tightened to proper
torque to avoid distortion of bores in
final
assem­
bly.
Always be sure the crankshaft is out of the

way
of the boring cutter when boring each cylinder.
When
boring, leave the diameter .001" [0,025 mm.]

undersize,
then finish hone to obtain the required

clearance.

When
honing cylinders, use clean sharp
stones
of
proper
grade for the amount of metal to be re­
moved. Refer to instructions supplied by the hone
manufacturer.
Dull
or dirty
stones
cut unevenly

and
generate excessive heat. When using coarse

or
medium grade
stones,
leave sufficient metal so
that all
stone
marks can be removed with the fine
stones
used to finish-hone to proper clearance.

When
finish-honing, pass the hone through the entire length of cylinder at a rate of approximately 60 cycles per minute.
This
should produce the

desired
45-degree
cross hatch pattern on cylinder

walls.
A proper pattern
will
ensure maximum
ring
life and minimum oil consumption.

After
final
honing and before the piston is checked

for
fit, each cylinder bore must be washed thor­ oughly to remove all traces of abrasive, then dried completely. The dry bore should be brushed clean

with
a power-driven fibre
brush.
If all traces of

abrasive
are not removed,
rapid
wear of new pistons

and
rings
will
result.

Note:
Wipe cylinder bores with a clean white

cloth,
moistened with SAE 10 oil. Cleaning should
continue until this
test
shows no sign of
dirt.

It
is of the greatest importance that refinished

cylinder
bores be true, with .0005" [0,013 mm.]
or
less out-of-round or taper.
Each
bore must have

a
smooth surface, without
stone
or cutter
marks.
After
final
honing and cleaning, each piston must be fitted individually to the bore in which it
will

be installed. Once fitted, each piston should be
marked
with its cylinder number to assure correct

installation.
85

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

N

13189

FIG.
N-36—PINION
SHAFT OIL
SEAL
INSTALLER
1—Tool
W-147
p.
Remove
the
sleeve
previously installed in
place

of
the yoke. Install the oil
seal
with
Tool
W-147 shown in Fig. N-36.
q. Install the yoke
with
Flange
Installer W-162,
as shown in Fig. N-3 7.

r.
Install pinion nut and cotter pin.
s. Install axle
shafts
and housing cover.
N-20.
POWR-LOK
DIFFERENTIAL

As
optional equipment, Powr-Lok was previously available on all
Jeep
Universal
models
equipped
with
semi-float
tapered
axle
shafts.
The Powr-Lok

differential
may be identified by a tag located on
the opposite
side
of the differential housing
from
the ratio tag (Fig. N-2) and
stamped
with
either a "T" or
with
the words, "USE
LIMITED
SLIP
FIG.
N-37—YOKE INSTALLING TOOL
DIFF.
LUBE
ONLY."
This differential is available

for
rear
axles
only.
Whenever a
replacement
or conversion Powr-Lok
differential
is to be installed in an axle which has

been
previously in
service
and acquired mileage, be
sure
to record the amount of backlash
between

the ring
gear
and pinion at the time of
disassembly.

When the axle is again
assembled
the ring
gear
and pinion must be set to this
same
amount of
back­

lash.

Axle
ratios and
speedometer
gear
application is very important. In
like
model
axles,
the ratio may
be
changed
by simply changing to the desired ring
gear
and pinion;
except
in the
case
of the
3.73:1

or higher ratios. When changing
from
a
3.73:1
or higher to 3.54 or lower ratio, or vice
versa,
the
differential
case
must
also
be
changed
on a
stand­

ard differential
assembly,
and the differential as­ sembly,
less
ring
gear
and pinion, when a Powr-Lok

differential
assembly
is involved. When changing
from
any ratio to
another,
it
will
also
be
necessary

to
change
speedometer
gears.
Speedometer
gears

for
Powr-Lok and
standard
differentials of the
same
ratio, are
interchangeable.
A complete
rear

axle
assembly
replacement
is
necessary,
if a con­
version
from
one type of differential
assembly
to
another
is desired.
Note: Powr-Lok differentials use a special
lubri­

cant.
Refer to the Lubrication Chart.

N-21.
Trouble Symptoms and
Possible
Causes
If
noises
such
as
chatter
are
detected,
when turning
a corner, the probable
reason
for this is that incor­
rect
gear
lubricant has
been
installed in the axle.

Axles
equipped
with
a
limited
slip differential require special lubricant. Refer to Lubrication
Sec­

tion,
Par. B-52.
Note: It may be
necessary
to use an additive to
attempt to eliminate
chatter.
If this is not
success­
ful
then
disassembly
and inspection of the differen­

tial
becomes
necessary.

Warning:
Extreme
care
must be exercised on a
Powr-Lok
equipped vehicle to be
sure
the transmis­
sion is in the neutral position
whenever
the
engine

is
started
with
one wheel jacked up. Otherwise the
vehicle may lurch unexpectedly and
fall
off the
jack.
N-22. Torque Test
Procedure
for testing torque Powr-Lok differentials

on
Jeep
Universal
Series
vehicles is as follows:
FIG.
N-38—POWR-LOK DIFFERENTIAL
1—
Differential
Case Flange
Half

2—
Disc
and Plate Set

3—
Side
Gear
Ring

4— Side
Gear
and Pinion Mate
Gear
Set
5—
Pinion
Mate
Cross
Shaft 6—
Differential
Case Button
Half
7—
Axle
Shaft Spacer
8—
Axle
Shaft Spacer
Roll
Pin 11564
301