washer fluid JEEP DJ 1953 Service Manual

B
LUBRICATION B-3.
SERVICE
MAINTENANCE
SCHEDULE

Perform
the following operations at the mileage shown. Two thousand miles equals
3,200
km.

SERVICE
MAINTENANCE
SCHEDULE

OPERATION
VEHICLE
^ n>
MILEAGE
IN
THOUSANDS

6 8 10 12 24 30
Check Wheel Nut Torque*
Check
Fluid
Level
in Battery X Check
Fluid
Level
in Brake Master Cylinder0. X
Service
Cooling
System X Service Tires X

Lubricate
Distributor
Cam Lubricator (F4-134) X
Lubricate
Steering Linkage X

Lubricate
Propeller Shaft Universal Joints X

Lubricate
Propeller Shaft
Slip
Joints ; X
Lubricate
Tie Rod and Drag
Link
Sockets................................... X Change Engine
Oil
and
Filter,
and Service Air Cleaner (F4 134 Engine)** X
Change Engine Oil and
Filter,
and Service Air Cleaner (V6-225 Engine)**....
Check Brake Operation and Pedal
Free
Play X Check
Clutch
Pedal
Free
Play. .... X
Check all
V-Belt
Tensions X
Check Exhaust Emission System
(If
so equipped)*** \ X
Service Positive
Crankcase
Vent
Valve
and Breather . .' X
Road Test
Including
a Check of all Instrument
Lights
and Controls X Tune-up Engine
Check Operation of
Manifold
Heat
Control
Valve

Clean
Exterior of Radiator

Align
Headlights • Check Brake
Linings
,
Check Exhaust System for Leaks Replace Canister Air
Filter
(F. E. E. C. System)
Check
Axle
U-Bolt
Torque. Check Lubricaunt
Level
of Front
Axle
Universal Joints
Check Shock Absorber Mountings and Bushings Check Front and
Rear
Spring Bushings

Lubricate
Distributor
(V6-225).
Replace Spark, Plugs
Check Charging and Starting Circuits
Lubricate
Tailgate Latch, Supports and Hinges.

Lubricate
Door and
Hood
Hinge Pivots ;
Lubricate
Glove Compartment Door Latch

Lubricate
Heater Controls •

Lubricate
Windshield
Wiper and Washer Controls
Clean,
Repack and
Adjust
Wheel Bearings
Change Transmission and Transfer Lubricant. .
Replace
Dry-Type
Air Cleaner • Check Lubricant
Level
of
Differential

Lubricate
Transfer
Case
Shift
LeArer
Control
C«se.
. , . . . . . . . .
Continuing
each
2,000 miles

Continuing
each
6,000 miles

Continuing
each
24,000 miles

X
Continuing
each
30,000 miles
•Check after the
first
200 miles [320
km.
J
of operation.
If
wheel or wheels are changed for any
reason,
have
wheel nut torque rechecked after an additional two hundred miles of operation
••Service mileage shown or every 60 days, whichever occurs
first.

•••Maintenance check on emission system must be performed per
information
in this manual. "See text for brakes.

"Nj
^Miles
2,000
6,000
12,000
18,000
24,000
30,000
Kilometers

3,200
9,600
19,200
28,800
38,400 48,000

B-9.
Engine Oil

For
maximum
engine
protection under all driving conditions encountered during the recommended

oil
change intervals, it is necessary to use only

"MS"
certified
sequence-tested
oils. The term
"MS"
must appear on the oil container singly or

in
conjunction with other designations. "MS" des­
ignated oils are heavy-duty detergent oils that are
formulated to withstand all service conditions in
modern powerplants. Engine oils designated only
as
"ML"
and/or
"MM"
are not recommended and should not be used except in an emergency when

"MS"
oil is not available. Certified
sequence-tested

engine
oils are described on their containers by

such
phrases as:
meets,
exceeds,
excels, or has
proven superior in the
test
requirements,
test
sequences, MS Service
tests,
standards, and service

requirements,
of automotive manufacturers, auto­
makers,
or car manufacturers for MS service or
Service
MS.
It
may be necessary to change
engine
oil more
frequently than normally recommended, depending upon the type and quality of oil used, the severity
of operation conditions, if the
engine
is used for
short
periods in cold weather, or if the
engine
is allowed to idle for excessive periods.

Always
drain
the crankcase while the
engine
is hot since
dirt
and contaminants are then more
likely
to be held in suspension and therefore
will

drain
out more completely.
Drain
the crankcase as follows:

a.
Position the
drain
receptacle under the
drain

plug.

b.
Remove the
drain
plug using the correct size

wrench.
Be careful of hot oil.
c.
Carefully
clean the
drain
plug. Inspect and

replace
the gasket, if deteriorated.
d.
When the oil has drained, replace and tighten
the crankcase
drain
plug. 12

COOLING
SYSTEM

14263

FIG.
G-2—COOLING SYSTEM
COMPONENTS
V-6
ENGINE

1—
Radiator
Pressure Cap

2—
Hose
Clamp

3—
Radiator
Hose (Inlet-Upper)
4—
Radiator
Hose (Outlet-Lower) 5—
Bolt
6—
Water
Pump Assembly 7—
Cap
8—Thermostat
By-Pass Hose
g—Water Outlet
Elbow

10—
Gasket

11—
Thermostat
12—
Water
Pump Gasket

13—
Dowel
Pin
14—
Radiator
Shroud (Heavy Duty Cooling) 15—
Pulley

16—
Fan
Spacer
17—
Fan
and Alternator Belt

18—Fan

19—
Lockwasher

20—
Radiator

21—
Drain
Cock
From
these
main passages, the coolant flows around
the
full
length of each combustion chamber.

After
cooling the block, the coolant passes through
ports between the block and each cylinder head.
These
ports direct most of the coolant flow around the exhaust valve area to prevent hot exhaust
gases

from
overheating the exhaust ports.

From
the cylinder heads, the water passes into a
water
manifold between each of the heads and the

water
pump. If the thermostat is closed, the coolant
is ported back to the pump where it is recirculated

back
into the pump and into the engine. After the
coolant heats enough to open the thermostat, the coolant is directed from the water manifold through
a
hose
to the top of the radiator and then through
the radiator which acts as a heat exchanger to cool the fluid. The coolant is then ported through a
hose

from
the bottom of the radiator to the pump, which

recirculates
it back to the engine.

The
cooling system is pressurized. Operating pres­
sure
is regulated by a relief valve in the radiator

cap. The
heater inlet
hose
is connected to a port on
the right bank cylinder head. The outlet
hose
is connected to the heater adapter tube on the water

pump.

c.
It is recommended when using water for coolant
that the cooling system be flushed and checked for leaks twice a year, preferably in the
fall
before
antifreeze is added and in the spring when the antifreeze is drained.

Reverse
flushing
will
aid greatly in removing rust 162

ELECTRICAL
SYSTEM

FIG.
H-66—WINDSHIELD
WIPER SWITCH ASSEMBLY (LATE)
B—Battery

1—
Wiper
1 La
Speed
2—
Wiper
1 Hi
Speed

3—
Wiper
2 Lo
Speed

4—Wiper
2 Hi
Speed
5— Park
g. If wiper operates erratically, check for
loose

wiper
ground connection or
loose
dash switch mounting.

H-145.
Wiper Troubleshooting on Bench

Using
ammeter, capable of reading at least 30
amperes, check
feed
wire circuit for open circuit.

a.
If wiper is inoperative, connect wiper to operate
in
low speed and observe current draw. If the read­
ing is zero amp., check for
loose
solder connection
at wiper terminal or
loose
splice joints. If reading is
1
to 1.5 amp., check for open armature, sticking
brushes, or
loose
splice joint. If reading is 11 amp.,
check for broken gear seized shaft or
some
other
condition that
will
stall the wiper.
b. If wiper
will
not shut off, this condition may
exist if wiper has one or both speeds. If wiper has both speeds, check for
park
switch contacts not
opening or internal wiper motor lead that connects to wiper terminal being grounded. If wiper has low
speed only, check for internal wiper motor lead that connects to wiper terminal being grounded. If

wiper
has high speed only, check for
internal
wiper motor lead that connects to wiper terminal being
open.

c.
If wiper
crank
arm
does
not return to
park

position when wiper is turned off, check for dirty, bent to broken
park
switch contacts.

d.
If wiper operates erratically, check for sticky
brushes or
loose
splice joints.
e. If the wiper
will
not shut off, or wiper
crank
arm
fails to
stop
in
park
position when jumper wire is
removed from terminal, check that
park
switch contacts are opening. Also check for ground in in­

ternal
motor lead that connects to terminal.
f-
Remove fastening screws, cover plate assembly

and
gasket.
g. Remove parking plate and gear assembly.

h.
Remove parking brushes, spring and bowed
washer from gear assembly.

i.
Remove the two through
bolts
and mounting

bracket.

j.
Remove the magnet housing, armature and end cap as an assembly.

k.
Tap end of armature shaft to
loosen
end cap
assembly and remove cap from armature shaft. Be
careful
not to
lose
thrust disc, which is in end cap
bearing bore.

I.
Remove armature from magnet housing.
Care

should be taken to protect armature shaft bearing

journals.

m.
Remove brushes and brush spring from brush
holders.

H-147.
Cleaning
of
Two-Speed
Wiper
Motor

a.
Clean
magnet housing and
armature
with a cloth dampened in cleaning solvent.

b.
The following bearing equipped parts should

not
be immersed in cleaning fluid: 1. Cover plate assembly.
2.
Gear
housing assembly.

3.
End cap assembly.

The
metal surfaces of
these
assemblies should be cleaned with a brush dipped in cleaning solvent,

making
certain that cleaning fluid
does
not contact bearings.

c.
Clean
remaining parts with a brush and cleaning
solvent.

H-148.
Reassembly
of
Two-Speed
Wiper
Motor

Refer
to Fig. H-67.
To
reassemble motor, reverse the
steps
given in

Par.
H-146.
When
reassembling motor, fingers must be clean
when handling brushes. Hold brushes in the holders by applying paper clips to brush shunts. Apply a
light film of lubricant to armature shaft ends,
armature
worm gear and gear assembly shaft ends.
Remove paper clips after assembling armature to gear housing. Align marks on magnet housing and
gear housing. Armature end play should be .002 -
.010".

Be
sure to operate wiper to
park
position prior to installing drive arm.

H-146.
Disassembly
of
Two-Speed Wiper Motor

Refer
to Fig. H-67.

a.
Remove windshield wiper motor cover.
b.
Disconnect drive arm from wiper linkage.

c.
Disconnect wiring from wiper dash switch.

d.
Remove wiper motor.

e.
Loosen drive arm hardware and pry drive off
drive
shaft.
H-149.
No
Load
Testing

Test
the motor to
meet
the following specifications:

LOW SPEED HIGH SPEED

Ampere Ampere

Draw Draw

R.P.M.
(Max.)
R.P.M.
(Max.)
42 2.75 62 3.75 218

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

P The
standard parking brakes (Fig. P-3) consist of
cable-controlled linkage for applying the rear wheel

brake
shoes
mechanically. A single cable from the

parking
brake control lever is connected, by means of an equalizer, to cables leading to individual rear

brakes.
A lever attached to the secondary
shoe,

with a link acting against the
primary
shoe,
expands the
shoes
into
contact with the drums.
P-4.
Transmission Brake

The
transmission brake is mechanically operated
by a hand lever through a cable and conduit and is mounted at the rear output bearing housing on the
transfer case. The transmission brake and its
linkage are shown in Fig. P-4.
P-5.
Brake Maintenance
No brake can be
expected
to work well when grease
or oil is allowed to leak
into
the drum from the rear axle. Little braking friction can be obtained

between
brakes and drums when the surface is
covered with grease and oil. For this reason, take
care
not to over-lubricate wheel bearings, forcing

lubricant
past seals. Also, check condition of seals

if
leak is suspected or whenever brake drums

are
pulled.
Whenever
wheels
are removed, it is advisable to
wash the drums with a suitable solvent so that all
grease and dirt are removed. Linings with any
evidence of grease or oil on them should be replaced.
The
hydraulic system should be kept free of dirt

and
moisture.
Use only SAE standard J-1703 Hydraulic
Brake
Fluid.

Caution:
Keep mineral oils, gasoline, or kerosene
out of the system as
they
cause rubber cups to

soften,
swell, and distort, resulting in failure.
P-6.
Brake
Service

To
service the brakes,
follow
the procedure
below:

a.
Check the fluid level in the brake master cylin­
der.
See Lubrication Section, Par. B-40.
b. Check brake pedal adjustment. See Par. P-9.
c. Check brake pedal travel. If the pedal travels more than halfway to the floor, the brake system
must be checked and the self adjusting star wheel mechanisms checked for binding, also the brake
linings should be inspected as
they
may be badly

worn.
How much lining is
left
can only be deter­ mined by visually inspecting the linings. See Par.
P-l6 for relining brakes.

d.
If the brakes pull to one side after adjustment, check tire pressures. All tires must be inflated to recommended pressures to ensure even braking. If
the condition persists, examine the brake linings
for foreign material and clean as necessary. If clean­
ing
does
not correct the condition the linings should be replaced. If the side pull persists, check front
wheel alignment and balance.
e. Check the brake system for leaks by applying a steady pressure on the brake pedal. A leak in the
system
will
allow the pedal to "fall away". If the pedal "falls away" check for a leaking wheel cylin­
der.
Remove
wheels
and drums and carefully check
each cylinder. Also examine all lines and fittings.

Rebuild
or replace all wheel cylinders (Par. P-21)

if
one is
defective
as
they
are all probably in poor condition. If the leak has allowed brake fluid to get
on the linings, the linings
will
have to be replaced.
f. A
"spongy"
brake pedal indicates the pressure of air in the hydraulic system.
This
condition must
be corrected by bleeding the brakes. See Par. P-7.
g. Should the brakes
become
locked so that the vehicle cannot be moved, the brakes may be re­
leased by opening the bleeder screw on any one of the wheel cylinders. Before the vehicle is driven, correct the cause of the condition. The cause may
3
14 15 16 17 18
4
10796

1—
Cable
and Conduit
2—
Hand
Brake
Clip

3—
Hand
Brake
Bracket
4—
Hand
Brake
Handle Assembly 5—
Rear
Cap
6—
Drive
Gear
Bushing
7—
Driven
Gear

8—
Driven
Gear
Sleeve
FIG.
P-4—TRANSMISSION
BRAKE

9—Backing
Plate
10— Shoe and
Lining

11—
Lever
End Return Spring
12—
Brake
Drum
13— Bolt 14—
Rear
Companion Flange
15—
Washer

16— Nut 17— Propeller Shaft Flange Yoke
18—
Rear
Propeller Shaft
19—
Adjusting
End Spring
20—
Adjusting
Screw Bracket
21—
Operating
Lever

22—
Clevis

23—
Retracting
Spring
Clip

24—
Retracting
Spring
Link
325

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

P
lengthening of the brake master cylinder eye bolt.

This
is
done
so the primary cup
will
clear the by­
pass port when the piston is in the off position,
otherwise the compensating action of the master

cylinder
for expansion and contraction of the fluid
in
the system, due to temperature changes,
will

be destroyed and cause the brakes to drag.

Note:
Some older 'Jeep' vehicles may
develop
side

movement
of the clutch and brake pedals resulting
from wear of the pedals, shafts, and bushings. One
way to
compensate
for this wear is to install a pedal

slack
adjuster kit,
Part
No.
921936.
FIG.
P-6—HAND
BRAKE
ADJUSTMENT

P-10.
Hand Brake

On
Model DJ-5 and DJ-6 vehicles the rear brake

shoes
are operated through cables and conduits to
form the hand or parking brake. A brake cable
equalizer and adjusting rod, Fig. P-6, is located directly back of the frame center cross member.

P-11.
Parking Brake Adjustment

•
Model DJ-5, DJ-6.

The
foot
brakes must be satisfactorily adjusted be­
fore attempting adjustment of the hand brake.

To
adjust the hand brake raise both rear
wheels

free of the floor.
Pull
up three
notches
on the hand

brake
lever and tighten the adjustment until the

rear
brakes drag slightly. Release the hand brake
lever and check the rear
wheels
for drag. The

wheels
must turn freely with the lever released.

P-12.
Transmission Brake Adjustment
The
transmission brake is located on the propeller
shaft at the rear of the transfer case, see Fig. P-4.
The
brake is operated by a cable connection from
the brake handle mounted on the instrument panel.

To
adjust the transmission brake, the following

sequence
should be followed:
Make
sure that the brake handle on the instrument
panel is fully released. Give due attention to the
cable and operating linkage to see that
they
do
not bind. If necessary free up the cable and
lubri­
cate it. Rotate the brake drum until one pair of the
three
sets
of
holes
are over the
shoe
adjusting screw

wheels
in the brake. Use the
edge
of the
holes
in
the brake drum as a fulcrum for suitable adjusting

tool
or a screwdriver, rotate each notched adjusting
screw by moving the handle of the
tool
away from
the center of the drive shaft until the
shoes
are
snug in the drum.
Back
off seven
notches
on the
adjusting screw
wheels
to secure proper running clearance
between
the
shoes
and the drum. Refer
to Fig. P-8.

P-13.
Relining Transmission Brake
Note:
The condition of the brake lining on the
transmission brake can be visually checked through
the adjusting
holes
in the brake drum.
FIG.
P-7—REMOVING
TRANSMISSION

BRAKE
DRUM

1— Tool W-172
2—
Adapter

3—
Brake
Drum
a.
To reline the brake
shoes
and make a major ad­
justment, first remove the four universal joint at­ taching nuts and lower the propeller shaft. Remove
the retracting spring clevis pin and the spring clip.
Remove the hug lock nut, the nut and washer from
the transfer case output shaft. Both the universal
joint companion
flange
and the brake drum may be readily removed by using puller Tool No. W-172

which
is illustrated in Fig. P-7. Remove the two

brake
shoe
retracting springs and the
shoes.

b. Clean all parts with a suitable cleaning solution

and
examine them for damage or wear.

Brake
shoes
may be distorted by improper lining
installation and the lining should be ground true
after installation on the
shoes.
For this reason it
is recommended that new or replacement
shoe
and
lining assemblies be installed.
c. To reassemble, first turn both adjusting screw

wheels
away from the center to "all off" position.
Place a light film of grease on the brake actuating

cam
and install the
shoes.
Install the black
shoe
re­

turn
spring next to the cam and the yellow spring next to the notch adjusting wheel screw. Place the
brake
drum and universal joint
flange
in position

and
install the transfer case output shaft washer,
nut and hug lock nut. 327

'Jeep*
UNIVERSAL SERIES SERVICE
MANUAL

P
f. On vehicles without a transmission brake hold
the brake
shoes
in their relative position and
engage
the parking brake cable
into
the parking

brake
lever.
g. On vehicles without a transmission brake in­
stall
the parking brake strut and spring
between

the parking brake lever and the primary
shoe.

h.
Place the brake
shoes
on the backing plate and

install
the retainer pins, springs and retainers.

i.
Install the anchor pin plate.

j.
Install the lever and
sleeve
on the primary
shoe
then install the secondary return spring, then the
primary
return spring.

Important:
A
"L"
or "R" is located on the hex­

agon
side of the lever crank for identification. The
lever crank marked "R" applies to the primary
shoe
on the
left
rear brake assembly. The lever
crank
marked
"L"
applies to the primary
shoe
on
the right rear brake assembly.
k. Place the upper linkage rod in the
groove
of the
anchor pin and
engage
the hook of the link rod
into

the adjusting lever.

I.
Install the brake drum. Install the wheel and

tire
assembly.
m. Adjust the brakes as described
below.

P-19.
Brake
Shoe
Initial
Adjustment —

a.
Should wheel brake units have
been
disassem­ bled for any reason, an initial adjustment
MUST
be made
before
drum installation.

b.
When the brake parts have
been
installed in
their correct position, initially adjust the adjusting
screw assemblies to a point where approximately Y% [9,53 mm.] of threads are
exposed
between
the

star
wheel and star wheel nut.

Note:
Following the initial adjustment and final
assembly, check brake pedal height to ensure

brake
operation. Then drive the car in reverse and
FIG.
P-12—BRAKE SHOE ADJUSTMENT
1—
Star
Wheel
2—
Lever

3—
Screwdriver
4—
Brake
Adjusting Tool
forward,
making 10 to 15 brake applications prior
to road testing.
This
action balances the adjust­
ment of the four brake units and raises the brake
pedal.
c. Adjustment may be made manually by remov­ing the access
slot
cover and using a brake adjust­
ing
tool
or screw driver to rotate the star wheel
until
the wheel is in the locked position. To tighten, rotate the star wheel in the clockwise direction.
Then
back off the star wheel at least 15 to 20

notches
(clicks).

d.
To back off the star wheel on the brake, insert
ice pick or thin blade screw driver in adjusting screw
slot
to hold lever away from adjusting screw.

Back
off on adjusting screw until wheel and drum

turn
freely. Replace adjusting
hole
cover.

Caution:
DO NOT attempt to back off on ad­
justing screw without holding adjuster lever away from screw as adjuster
will
be damaged.
P-20. Master Cylinder Reconditioning —
Dual
System

Refer
to Fig. P-13.

DISASSEMBLY
a.
Remove the filler cap and empty all fluid.
b.
Remove the snap ring, push rod assembly, and
the primary and secondary piston assemblies. Air pressure applied in the piston
stop
hole
will
help
facilitate the removal of the secondary piston as­
sembly.
c. The residual check valves are located under
the front and rear fluid
outlet
tube
seats.

d.
The
tube
seats
must be removed with the
self-

tapping screws supplied in the repair kit to permit removal of the check valves. Screw the self-tapping
screws
into
the
tube
seats
and place two screw

driver
tips under the screw head and force the
screw upward as shown in Fig. P-14.
e. Remove the expander in the rear secondary cup, secondary cups, return spring, cup protector,
pri­

mary
cup, and washer from the secondary piston.
f. The primary piston, with the rubber cups in­ stalled, is supplied in the repair kit.

CLEANING
a.
After disassembly, immersion of all metal parts
in
clean brake fluid or a brake system cleaner is
recommended. Use air
hose
to blow out dirt and cleaning solvent from recesses and internal pas­

sages.
When overhauling a hydraulic brake unit,
use all parts furnished in the repair kit. Discard
all
old rubber parts.

b.
After cleaning, place
all"
hydraulic
system parts
on clean paper or in a clean pan.

INSPECTION
Inspect all other parts for damage or
excessive

wear.
Replace any damaged, worn, or chipped
parts.
Inspect hydraulic cylinder bore for
signs
of
scoring, rust, pitting, or etching. Any of
these
will
require
replacement of the hydraulic cylinder. 331

BRAKES

12519

FIG.
P-13—DOUBLE
SAFETY MASTER CYLINDER
1— Boot
2— Snap Ming 3"*—Piston Assembly
4—
Backing
Ring 5—
Master
Cylinder Cup 6—
Master
Cylinder Cup
7— Piston
8—
Master
Cylinder Cup 9—
Cup
Protector
10—Spring 11—
Cylinder
Housing
12—
Cover
Gasket
13—
Cover

14—
Washer
Gasket 15—
Washer
16—
Cover
Bolt
17—
Check
Valve Spring 18—
Check
Valve
19—
Tube
Seat
20— Piston Stop
REASSEMBLY

a.
Prior
to reassembly of the master cylinder, dip

all
components
in clean brake fluid and place on
clean paper or in a clean pan.

b.
Install the primary cup washer, primary cup,
cup protector, and return spring on the secondary piston.
c. Install the piston cups in the double
groove
end
of the secondary piston, so the flat j of the cups face each other (lip of cups away from each other).
Install
the cup expander in the lip
groove
of the
end cup.

cL
Coat the cylinder bore and piston assemblies with clean brake fluid
before
installing any parts

in
the cylinder.
e. Install the secondary piston assembly first and then the primary piston which is supplied in the
repair
kit.

f.
Install the push rod assembly, which includes
the push rod,
boot,
and rod retainer, and secure
with the snap ring. Install the primary piston
stop.

g. Place new rubber check valves over the check valve springs and install in the
outlet
holes, spring
first.

Note:
When replacing a
complete
master cylinder
with a service unit, the original push rod must be used. The push rod retainer and snap ring retainer 12617

FIG.
P-14—REMOVING TUBE SEATS 1
—Screwdriver

2— No. 6-32 Self-Tapping Screw

3—
Tube
Seat must be removed and discarded. As the new unit
has the retainers installed it is only necessary to

install
the push rod until a "snap" is heard and the push rod is retained. 332