JEEP LIBERTY 2008 KK / 2.G Owners Manual

Cavity Cartridge
FuseMini
FuseDescription
M26 Ð 10 Amp
RedPower Mirror Switch/
Driver Window
Switch
M27 Ð 10 Amp
RedIgnition Switch/
Wireless Control
Module (WCM)/
Steering Column Lock
- if equipped
M28 Ð 10 Amp
RedPowertrain Control
Module (PCM)
M29 Ð 10 Amp
RedOccupant Classifica-
tion Module (OCM)
M30 Ð 15 Amp
BlueRear Wiper Module -
if equipped/
Diagnostic Link
M31 Ð 20 Amp
YellowBack-Up LightsCavity Cartridge
FuseMini
FuseDescription
M32 Ð 10 Amp
RedOccupant Restraint
Controller (ORC)
M33 Ð 10 Amp
RedPowertrain Control
Module (PCM)
M34 Ð 10 Amp
RedPark Assist Module -
if equipped/Heating,
Ventilation, & Air
Conditioning (HVAC)
Module - if
equipped/Compass
Module - if equipped
M35 Ð 10 Amp
RedHeated Mirrors - if
equipped
M36 Ð Ð Ð
MAINTAINING YOUR VEHICLE 441
7

Cavity Cartridge
FuseMini
FuseDescription
M37 Ð 10 Amp
RedAnti-Lock Brake Sys-
tem (ABS)/Electronic
Stability Program
(ESP) Module/Stop
Light Switch
M38 Ð 25 Amp
NaturalDoor & Liftgate
Lock/Unlock MotorsCAUTION!
²When installing the Integrated Power Module
cover, it is important to ensure the cover is prop-
erly positioned and fully latched. Failure to do so
may allow water to get into the Integrated Power
Module, and possibly result in an electrical system
failure.
²When replacing a blown fuse, it is important to
use only a fuse having the correct amperage rating.
The use of a fuse with a rating other than indicated
may result in a dangerous electrical system over-
load. If a properly rated fuse continues to blow, it
indicates a problem in the circuit that must be
corrected.
442 MAINTAINING YOUR VEHICLE

REPLACEMENT LIGHT BULBS
LIGHT BULBS Ð Interior Bulb No.
Cargo Light........................WL212±2
Overhead Console Light.............. PLW214±2A
Reading Light.......................WL212±2
LIGHT BULBS Ð Exterior Bulb No.
Headlight..........................9008 H13
Front Park/Turn Signal Light.............3757AK
Front Side Marker Light.................... 168
Back-Up Light.........................3157K
Center High Mounted Stop Light
(CHMSL)............................. LED
(Serviced at Dealer)
Fog Light.......................... H109145
License Plate Light....................... 168
Rear Tail/Stop.........................3157K
Rear Turn Signal Light..................3757AK
BULB REPLACEMENT
Headlight
1. Open the hood.
2. Reach behind the headlight housing to access the
headlight bulb lock ring.
3. Firmly grasp the lock ring and rotate it counterclock-
wise to unlock it.
4. Remove the bulb and connector assembly from the
headlight housing.
5. Disconnect the bulb from the electrical connector and
then connect the replacement bulb.
MAINTAINING YOUR VEHICLE 443
7

CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.
6. Install the bulb and connector assembly into the
headlight housing and rotate the lock ring clockwise to
lock it in place.
7. Close the hood.
Front Turn Signal and Front Side Marker Lights
1. Turn the steering wheel all the way to the right to
access the left front turn signal or side marker. Turn the
steering wheel all the way to the left to access the right
front turn signal or side marker.
2. Remove three push-pins from the wheel-well liner.
3. Gently flex the wheel-well liner forward to access the
bulb.
4. Rotate the bulb's socket counterclockwise, and remove
the bulb and socket assembly from the housing.
5. Pull the bulb out of the socket and insert the replace-
ment bulb.
6. Install the bulb and socket assembly into the housing,
and rotate the socket clockwise to lock it in place.
7. Reposition the wheel-well liner and install the push-
pins.
444 MAINTAINING YOUR VEHICLE

Front Fog Light
1. Open the hood.
2. Reach behind the headlight housing to access the bulb.
3. Rotate the bulb's socket counterclockwise, and remove
the bulb and socket assembly from the fog light housing.
4. Pull the bulb out of the socket and insert the replace-
ment bulb.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.5. Install the bulb and socket assembly into the into the
fog light housing, and rotate the connector clockwise to
lock it in place.
6. Close the hood.
Rear Tail/Stop, Turn Signal, and Back-Up Lights
1. Open the liftgate.
2. Remove the screws that fasten the taillight housing to
the vehicle.
3. Pull the taillight housing straight back to separate it
from the vehicle.
4. Disconnect the electrical connector.
MAINTAINING YOUR VEHICLE 445
7

5. Remove the two screws that fasten the back plate to
the taillight housing.
6. Separate the back plate from the taillight housing.
7. Pull the appropriate bulb(s) out of the back plate and
insert the replacement bulb(s).8. Install the back plate and screws into the taillight
housing.
9. Connect the electrical connector.
10. Install the taillight housing and screws.
11. Close the liftgate.
446 MAINTAINING YOUR VEHICLE

FLUID CAPACITIES
U.S. Metric
Fuel (approximate)
3.7 Liter Engine 19.5 Gallons 73.8 Liters
Engine Oil-With Filter
SAE 5W-20, API Certified 5 Qts 4.7 Liters
Cooling System *
MopartAntifreeze/Coolant 5 Year/100,000 Mile Formula or equivalent. 14 Qts 13 Liters
* Includes heater and coolant recovery bottle filled to MAX level.
MAINTAINING YOUR VEHICLE 447
7

FLUIDS, LUBRICANTS, AND GENUINE PARTS
Engine
Component Fluids, Lubricants, and Genuine Parts
Engine Coolant MopartAntifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or-
ganic Additive Technology) or equivalent.
Engine Oil Use API Certified SAE 5W-20 Engine Oil meeting the requirements of
DaimlerChrysler Material Standard MS-6395. Refer to the engine oil fill cap
for correct SAE grade.
Spark Plugs ZFR6F-11 (Gap.043 in [1.1 mm])
Oil Filter Mopart5281090 or equivalent.
Fuel Selection 87 Octane
448 MAINTAINING YOUR VEHICLE

Chassis
Component Fluids, Lubricants, and Genuine Parts
Automatic Transmission MopartATF+4, Automatic Transmission Fluid.
Manual Transmission MopartManual Transmission Lubricant or equivalent (meeting the re-
quirements of DaimlerChrysler Material Standard MS-9224)
Transfer Case MopartATF+4, Automatic Transmission Fluid.
Front Axle SAE 80W-90 Multipurpose Type, GL-5 Gear Lubricant or equivalent.
Rear Axle SAE 75W-140 Synthetic Gear Lubricant or equivalent.
Brake Master Cylinder/Manual
Transmission Clutch SystemMopartDOT 3, SAE J1703 or equivalent should be used. If DOT 3 brake
fluid is not available, then DOT 4 is acceptable. Use only recommended
brake fluids.
Power Steering Reservoir MopartATF+4, Automatic Transmission Fluid.
MAINTAINING YOUR VEHICLE 449
7