key JEEP RENEGADE 2018 Owner handbook (in English)

Tailgate lock locking: with tailgate closed
press button A fig. 15.NOTE The tailgate door lock also
performs a central locking of the doors.
Boot opening is disabled while the car is
moving.
DEAD LOCK(where provided)
9)
This inhibits the operation of the interior
door handles and the door
locking/unlocking button.
Activating the device: the device is
enabled on all the doors by quickly
double-pressing the
button on the key.
Deactivating the device: press button
on
the key with remote control or place the
ignition device to MAR.
CHILD SAFETY DEVICE
10)
This system prevents the rear doors from
being opened from the inside.
The device A fig. 16 can only be engaged
with the doors open:
position: device engaged (door
locked);
position: device not engaged (door
may be opened from the inside).The device remains engaged even if the
doors are electrically unlocked.
IMPORTANT The rear doors cannot be
opened from the inside when the child
lock device is engaged.
14J0A0621C
15J0A0896C
16J0A0041C
23

WARNING
8)NEVER leave children unattended
inside the car, let alone leave the car with
the doors unlocked in a place that
children can access easily. Children may
seriously, or even fatally, injure
themselves. Also ensure that children do
not inadvertently operate the electric
parking brake, the brake pedal or the
automatic transmission lever.
9)Always use this device when carrying
children. After engaging the child lock on
both rear doors, check for effective
engagement by trying to open a door with
the internal handle.
10)Once the Dead Lock system is
engaged, it is impossible to open the
doors from inside the vehicle. Before
getting out of the car, please therefore
check that there is no-one left inside.
IMPORTANT
2)Make sure to take the key with you once
a door or the tailgate is locked, to prevent
locking the same key inside the vehicle. If
the key has been locked in, it can only be
recovered using the second provided key.
3)The operation of the recognition system
depends on various factors, such as, for
example, any electromagnetic wave
interference from external sources (e.g.
mobile phones), the charge of the battery
in the electronic key and the presence of
metal objects near the key or the car. In
these cases it is still possible to unlock the
doors by using the metal insert in the
electronic key (see description on the
following pages).
SEATS
FRONT SEATS WITH MANUAL
ADJUSTMENT
11)4)
Longitudinal adjustment: lift the lever A
fig. 17 and push the seat fully forward or
backward.
12)
IMPORTANT Carry out the adjustment
while sitting on the seat involved
(driver side or passenger side).
Height adjustment(where provided): move
17J0A0043C
24
GETTING TO KNOW YOUR CAR

The electrochromic mirror has an
ON/OFF button to activate/deactivate the
electrochromic anti-glaring function.
DOOR MIRRORS
Electric adjustment
18)
Adjusting the mirrors is possible with the
ignition device at MAR and for about
3 minutes after the ignition device
switches to STOP (or also after the
mechanical key has been extracted, for
cars equipped with mechanical key with
remote control). When one of the front
doors is opened this operation is
disabled.Select the desired mirror using device A
fig. 29:
device in position 1: left mirror
selected;
device in position 2: right mirror
selected.
To adjust the selected mirror, press
button B fig. 29 in the four directions
shown by the arrows.
IMPORTANT To prevent accidental
movement once adjustment is
complete, rotate device A fig. 29 to
position 0.
Electric mirror folding
(where provided)
To fold the mirrors, press button Cfig. 29. Press the button again to restore
the mirrors to the driving position. If
button C is pressed during door mirror
folding (from closed to open position and
vice versa), their movement direction is
reversed.
You can fold or open the mirrors with the
ignition device at MAR and for about
3 minutes after switching the ignition
device to STOP (or also after extracting
the mechanical key, for cars equipped
with a mechanical key with remote
control). When one of the front doors is
opened this operation is disabled.
IMPORTANT While driving mirrors
must always be open and should never
be folded.
Mirrors realignment operation
In case one of the door mirrors has been
moved manually it may occur that the
mirror itself does not retain its position in
a stable way while driving.
In that case it is necessary to carry out
the following realignment operation:
manually close the mirror to the
parking position by folding it from
position 1 to position 2 fig. 30;
operate the mirror opening control C
fig. 29 once or twice to realign the
system and bring both mirrors to the
driving position.
28J0A0059C
29J0A0061C
30
GETTING TO KNOW YOUR CAR

If the headlights are switched off before
the ignition, they will switch off normally.
MAIN BEAM HEADLIGHTS
To activate the fixed main beam
headlights, with the ignition device in
MAR, push left lever A fig. 32 (car travel
direction). The light switch should be
turned toAUTOwith the dipped beam
headlights on, or it should be turned to
position
.
To flash, the unstable position is used
(activate by pulling the lever towards
you). With main beam headlights on, the
warning light on the instrument
panel will come on at the same time.
The main beam headlights are
deactivated bringing the lever back to the
central stable position. Warning light
switches off in the instrument panel.Automatic main beam headlights
This function is enabled with the display
Menu or theUconnect™system, and with
the light switch turned to AUTO.
The first time the main beam headlights
are activated (pushing the left lever), the
function is activated (green warning light
comes on in the instrument panel).
If the main beam headlights are actually
on, the blue
warning light will also
come on in the instrument panel.
To deactivate the automatic function
rotate the light switch ring nut to position
.
DIRECTION INDICATORS
Bring left lever A fig. 32 to the (stable)
position:
upwards: activates the right direction
indicator;
downwards: activates the left direction
indicator.
"Lane Change" function
If you wish to signal a lane change, place
the left lever in the unstable position for
less than half a second. The direction
indicator on the side selected will flash
five times and then switch off
automatically.
COURTESY LIGHTS
This function, with the ignition device in
MAR, allows activating the side lights
and the number plate lights for
25 seconds, each time the car is
unlocked with the key with remote
control, or the “Passive Entry” system
(where present).
Enabling the function can be adjusted
through the display Menu or the
Uconnect™system.
The function is automatically disabled
once the activation time elapses
(25 seconds), or when the car doors are
locked again, or by turning the ignition
device to a non-MAR position.
32J0A0063C
33

IMPORTANT
2)The system uses R134a coolant, which
does not pollute the environment in the
event of accidental leakage. Under no
circumstances use R1234yf and
R12 fluids, which are incompatible with
the components of the system.
ELECTRIC WINDOWS
ELECTRIC WINDOWS
22)
They operate with the ignition device at
MAR and for nearly 3 minutes after the
ignition device switches to STOP (or also
after the mechanical key has been
extracted, for vehicles equipped with
mechanical key with remote control).
When one of the front doors is opened
this operation is disabled.
Driver side front door controls
The buttons are located on the trims of
the left side door panels (left hand drive
versions) or of the right side door panels
(right hand drive versions). All windows
can be controlled from the driver side
door panel fig. 39.
A: front left window opening/closing.
"Continuous automatic" operation during
window opening/closing stage and
anti-pinch system activated.
B: right front window opening/closing.
"Continuous automatic" operation during
window opening/closing stage and
anti-pinch system activated.
C: enabling/disabling of rear door
electric window controls;
D: left rear window opening/closing (if
present). "Automatic continuous"
operation during window opening/closing,
manual electric operation during window
closing;
E: right rear window opening/closing
(if present). "Automatic continuous"
operation during window opening/closing,
39J0A0078C
45

manual electric operation during window
closing.
Window opening
Push the buttons to open the desired
window.
When any of the opening buttons on front
or rear doors is pressed briefly, the
window moves in stages; if the button is
held down, "continuous automatic"
operation is activated.
If the button is pressed again, the
window will stop in the desired position.
Window closing
Lift the buttons to close the desired
window.
The window closing stage occurs
following the same logic described for
the opening stage, for the front door
windows only.
The rear door windows can only be closed
"in stages".
Front window anti-pinch safety device
(where provided)
This safety system can recognise the
presence of any obstacle during the
window closing movement. If this occurs,
the system stops the window's movement
and reverts it by a few centimetres,
depending on its position.
The anti-crush safety function isactivated both during the manual and the
automatic operation of the window.
Electric window system initialisation
If power supply is interrupted, the
electric window automatic operation
must be reinitialised.
The initialisation procedure described
below must be carried out with the doors
closed and for each door:
fully close the window to be
initialised, with manual operation;
after the window has reached the
upper end of travel, hold the up button
down for at least 3 seconds.
WARNING
22)Incorrect use of the electric windows
may be dangerous. Before and during their
operation, ensure that any passengers are
not at risk from the moving glass either by
personal objects getting caught in the
mechanism or by being hit by it directly.
When leaving the vehicle (equipped with
mechanical key with remote control),
always remove the key from the ignition
device to prevent accidental operation of
the electric windows from being a hazard
for those still on board.
ELECTRIC SUN ROOF
23)11)
The electric sun roof comprises two glass
panels (the front one is mobile and the
rear one fixed) and is fitted with an
electrically operated sun blind.
On some versions, the front panel might
be electrically operated.
The sun roof and the blind can be
operated only with the ignition device
turned to MAR.
CONTROL BUTTONS
Button Afig. 40: press the button on the
front glass panel to open it fully. Pull the
button: the front panel will close fully.
Press button A again during automatic
opening and closing to stop the blind
movement.
46
GETTING TO KNOW YOUR CAR

Button Bfig. 40: Briefly press button B
will open the sunshade blind in “steps”.
Pressing the button for longer, instead,
will activate “continuous automatic”
opening. Briefly pulling the button will
give a “snap” closing of the sunshade
blind. Keeping the button pulled,instead, will activate “continuous
automatic” closing.
Button Cfig. 40: press and release the
button to move the roof to the “spoiler”
position (swivel opening). This type of
swivel opening can be activated
irrespective of the position of the
sunroof. During “spoiler” opening, any
pressure on button C stops the roof
closing. Press button C with the roof fully
closed to open the roof to the “swivel”
position. If the roof is positioned between
the fully open position and the “swivel”
position, press button C to close it
manually.
ANTI-PINCH DEVICE
The sun roof and the electric blind are
equipped with an anti-pinch safety
system capable of detecting the presence
of an obstacle whilst the roof is closing:
if this happens, the system intervenes
and the movement of the glass is
immediately reversed.
EMERGENCY OPERATION
If the control buttons fail to operate, the
sun blind and the sun roof can be moved
manually, proceeding as described
below:
Sun blind movement: remove protective
cap A fig. 41 on the internal trim;
Sun roof movement: remove protective
cap B on the internal trim;
take the supplied spanner C from the
luggage compartment;
insert key C in housing A (for blind
movement) or B (for sun roof movement)
and turn it clockwise to open the roof (or
the blind) or anticlockwise to close the
roof (or the blind).
INITIALISATION PROCEDURE
Following an automatic movement
malfunction while opening/closing or
after an emergency manoeuvre (see
description in the previous paragraph),
the automatic operation of the sun roof
must be initialised again.
40J0A0224C
41J0A00390C
47

Proceed as follows:move the roof to fully closed position;move the ignition device to STOP and
keep it there for 10 seconds;
move the ignition device to MAR;press button A: fig. 40 in "closing"
position;
press the button for at least
10 seconds, then you should hear the
mechanical stop of the roof motor;
press the button A in the "closing"
position again within 5 seconds;
hold down button A: in this position,
the roof will perform an automatic
opening and closing cycle. Otherwise,
repeat the operations starting from the
beginning;
hold down button A until the roof is
completely closed: the initialisation
procedure has ended.
WARNING
23)When leaving the vehicle (equipped
with mechanical key with a remote
control), always remove the key from the
ignition device to avoid the risk of injury
to those still inside the vehicle due to
accidental operation of the sun roof.
Improper use of the roof can be
dangerous. Before and during operation,
always check that no-one is exposed to the
risk of being injured by the moving
sunroof or by objects getting caught or hit
by it.
IMPORTANT
11)Do not open the sun roof if a
transverse roof rack is fitted. Do not open
the sun roof if there is snow or ice on it:
you may damage it.
MySky SUN ROOF
12)
The roof has two panels, a front and a
rear one, that can be individually or
simultaneously removed, as wished.
Front and rear panels are distinguished
by a dedicated symbol on the bottom of
the panels themselves.
IMPORTANT The panels can withstand
any snow that may deposit on them. In
any case, it is advisable to remove
excessive snow.
FRONT PANEL ELECTRIC
MOVEMENT
On some versions, the front panel might
be electrically operated.
This operates only with the ignition
device at MAR. The panel can be
adjusted forward/backward and opened
in “swivel” position.
The buttons to operate the front panel
are located on the trim close to the front
ceiling light fig. 42:
Button A: open/close the front panel to
the end of its travel. Press button A to
fully open the front glass panel. Pull the
button: the front panel will close fully.
48
GETTING TO KNOW YOUR CAR

position the panels inside, making
sure that the two handles are reciprocally
opposed (see fig. 48 ), then reposition
the baffle properly in its housing;
close the bag again, position it
correctly inside the luggage compartment
and then secure the bag firmly to the
retaining hooks on the luggage
compartment crossmember (see fig. 49 ).
IMPORTANT Do not lay evenly
distributed loads on the bag if they
exceed 10 kg in weight.EMERGENCY OPERATION
If the control buttons fail to operate, the
sun roof can be moved manually,
proceeding as described below:
remove protective cap A fig. 50 on
the internal trim;
introduce the supplied key B into
housing A and turn it clockwise to open
the roof or anticlockwise to close it.
INITIALISATION PROCEDURE
Following an automatic movement
malfunction while opening/closing or
after an emergency manoeuvre (see
description in the previous paragraph),
the automatic operation of the sunroof
must be initialised again.
47J0A0630C
48J0A0490C
49J0A0417C
50J0A0080C
51

LUGGAGE COMPARTMENT
The luggage compartment unlocking is
electrically operated and is deactivated
when the vehicle is in motion.
OPENING FROM THE OUTSIDE
28)
When unlocked, the boot can be opened
from outside the car using the electric
opening handle A fig. 54 located under
the handle until the unlocking click is
heard or by quickly pressing button
on the remote control twice.Emergency opening from the inside
Proceed as follows:
remove parcel shelf (where provided),
remove the rear head restraints and fully
fold the seats;
use the screwdriver to remove the
yellow tab A fig. 55;
insert the screwdriver in housing B
fig. 56, in order to activate the luggage
compartment release tab.
CLOSING
To close the luggage compartment grab
the handle located inside the tailgate.
IMPORTANT Before closing the
luggage compartment make sure that
you have the keys since the luggage
compartment is automatically locked.
54J0A0895C
55J0A0085C
56J0A0214C
54
GETTING TO KNOW YOUR CAR