window JEEP WRANGLER 2007 JK / 3.G User Guide

▫Door Frame Removal (4 Door Models)......135
▫Door Frame Installation (4 Door Models)....138
Soft Top (2 Door Models).................141
▫Folding Down The Soft Top..............143
▫Putting Up The Soft Top................151
Sunrider — 4 Door Models................160
Soft Top (4 Door Models).................164
▫Folding Down The Soft Top..............166
▫Putting Up The Soft Top................176Folding Windshield.....................187
▫Lowering The Windshield And Removing
Side Bars...........................189
▫Raising The Windshield And Replacing Side
Bars...............................192
Rear Window Features — Hard Top Only.....193
▫Rear Window Wiper/Washer — If Equipped . . 193
▫Rear Window Defroster — If Equipped......195
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

MIRRORS
Inside Day/Night Mirror
The mirror should be adjusted to center on the view
through the rear window. A two-point pivot system
allows for horizontal and vertical adjustment of the
mirror.Annoying headlight glare can be reduced by moving the
small control under the mirror to the night position
(toward rear of vehicle). The mirror should be adjusted
while set in the day position (toward windshield).
Adjusting Rearview Mirror
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85
3

DUAL TOP — IF EQUIPPED
If your vehicle is equipped with a Dual Top,you must
remove one of the tops from the vehicle. If the soft top
is removed, the pivot brackets must also be removed
from the sport bar.The soft top was installed at the
factory for shipping purposes only.The soft top and the
hard top are to be used independently.Removal is
mandatory to prevent any possible wear and tear on the
soft top. Your vehicle warranty will not cover damage
resulting from both tops remaining on the vehicle at the
same time for extended periods of time.
Removing The Soft Top
1. Locate and remove the 2 boxes that contain the
following items:
•Right and left door frames
•Door frame attachment knobs (4 for 2 door models,
6 for 4 door models)
•Right and left quarter windows
•Rear window
•Rear window roll up straps (2)
•Sunrider secure straps (2) (If Equipped)
•Rear swing gate brackets (2)
2. Remove the hard top. Refer to “Freedom Top 3 – Piece
Modular Hard Top — Front/Rear Panel Removal” later
in this section.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

5. Unzip the zipper on the sport bar cover to expose the
pivot brackets. Remove the brackets using a #T30 Torx
head driver. Recover and re-zip the sports bar cover.
Store pivot brackets and screws in a safe place.
6. Reinstall the hard top. Refer to “Freedom Top 3 —
Piece Modular Hard Top — Front/Rear Panel Installa-
tion” later in this section.Installing the Soft Top
NOTE:The following procedures are for first time set
up only. For future soft top procedures, refer to “Soft
Top” in this section.
1. Locate and remove the following items prior to hard
top removal:
•Right and left door frames
•Door frame attachment knobs (4 for 2 door models,
6 for 4 door models)
•Right and left quarter windows
•Rear window
2. Remove the hard top. Refer to “Freedom Top 3 —
Piece Modular Hard Top — Front/Rear Panel Removal”
later in this section.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

5. Unsnap and remove the black boot cover. This cover
should be discarded. It was intended as a protective
cover for shipping only.
NOTE:A visual instruction sheet is enclosed in the dual
top wrap.
6. Remove the swing gate bar (black metal bar for
bottom of rear window) located in the soft top and set
aside.
NOTE:Be sure the wire harness in the right rear corner
is not tangled in the soft top bows before you lift the top.
7. Put up the soft top. Refer to “Soft Top — Putting Up
the Soft Top” in this section.FREEDOM TOP 3– PIECE MODULAR HARD TOP
CAUTION!
•The hard top is not designed to carry any addi-
tional loads such as roof racks, spare tires, build-
ing, hunting, or camping supplies, and/or luggage,
etc. Also, it was not designed as a structural
member of the vehicle, and thus cannot properly
carry any additional loads other than environmen-
tal (rain, snow, etc.).
CAUTION!
Do not move your vehicle until the top has been
either fully attached to the windshield frame and
bodyside, or fully removed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125
3

2. Install right panel first, then the left panel.
3. Reinstall panel(s) using the same steps for removal in
reverse order.
Rear Panel Removal
1. Remove both front panels. Refer to “Front Panel(s)
Removal” in this section.
2. Open both doors.
3. Remove the two (2) Torxhead screws which secure
the hard top at the B-pillar (near top of door) using a #40
Torxhead driver (4 Door Only).
4. Remove the six (6) Torxhead screws which secure the
hard top to the vehicle (along the interior bodyside) using
a #40 Torxhead driver.5. Open swing gate all the way to ensure clearance of the
rear window glass. Lift rear window glass.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129
3

CAUTION!
•Do not run a fabric top through an automatic car wash.
Window scratches and wax build up may result.
•Do not lower the top when the temperature is below
41°F (5°C). Damage to the top may result.
•Do not move your vehicle until the top has been either
fully attached to the windshield frame, or fully low-
ered.
•Do not lower the top with the windows installed.
Window and top damage may occur.
•Refer to “Appearance Care for Fabric Top Models” in
Section 7 of this manual. It contains important infor-
mation on cleaning and caring for your vehicle’s fabric
top.
•Do not use any tools (screwdrivers, etc.) to pry or force
any of the clamps, clips, or retainers securing the soft
top. Do not force or pry the soft top frame work when
opening or closing. Damage to the top may result.
WARNING!
•Do not drive vehicle with rear window curtain up
unless side curtains are also removed. Dangerous
exhaust gases could enter the vehicle causing harm
to the driver and passengers.
•The fabric upper doors and fabric top are designed
only for protection against the elements. Do not
rely on them to contain occupants within the
vehicle or to protect against injury during an
accident. Remember, always wear seat belts.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Folding Down The Soft Top
1 — Header Bow 6 — Body Side Retainer
2 — 2 Bow 7 — Quarter Window
3 — 3 Bow 8 — Check Strap
4 — Sail Panel 9 — Front Retainer — Quarter Window
5 — Plastic Retainer 10 — Bottom Retainer — Quarter WindowUNDERSTANDING THE FEATURES OF YOUR VEHICLE 143
3

NOTE:Clean side and rear windows before removal to
assist in preventing scratching during removal of the soft
top. If zippers are difficult to operate due to road dust,
etc., clean them with a mild soap solution and a small
brush. Cleaning products are available through your
authorized dealer.
1. If your vehicle has half doors, remove each half door
window by opening the door and lifting the half door
window out.
NOTE:Stow half doors carefully outside of the vehicle,
never inside to avoid scratches.
2. Insert finger behind the plastic retainer. Pull down and
roll the retainer out of the channel. Repeat this on the
opposite side.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145
3

3. Unclip and move the sun visors to the side.
4. Release the header latches and leave the hooks in the
loops on the windshield.
5. Open the swing gate.6. Before unzipping the rear window, release the first
three (3) inches of both sail panels from the channel.
Remove the swing gate bar by pulling it straight rear-
ward out of the swing gate brackets.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE