KIA CARNIVAL 2007 Workshop Manual

Page 321 of 1575

3.Disconnect the fuel filler hose (A) and the leveling hose (B).
4.Disconnect the fuel feed quick connector (A) and vaccum hose (B).
5.Remove the fuel tank band (A) with unscrewing the mounting bolts (B) and remove the fuel tank from the vehicle.
INSTALLATION
1.Install the Fuel Tank according to the reverse order of "REMOVAL" procedure.
Fuel tank band mounting bolts :
39.2 ~ 53.9 N·m (4.0 ~ 5.5 kgf·m, 28.9 ~ 39.8 lbf·ft)

Page 322 of 1575

Fuel Pump

Page 323 of 1575

2007 > 2.7L V6 GASOLINE >
REMOVAL(INCLUDING FUEL FILTER AND FUEL PRESSURE REGULATOR)
1.Preparation
(1) Remove the 2nd seat(s) (Refer to "BD" group in this WORKSHOP MANUAL).
(2) Remove the striker cover (A).
(3) Remove the Service Cover (B).
(4)Disconnect the Fuel Pump Connector (A).
(5)Start the engine and wait until fuel in fuel line is exhausted.
(6) After the engine stalls, turn the ignition switch OFF.
2. After disconnecting the fuel feed quick connector (A) and unscrewing the the eight screws (B), remove the fuel
pump assembly.

Page 324 of 1575

INSTALLATION
1.Install the Fuel Pump assembly according to the reverse order of "REMOVAL" procedure.
Fuel Pump assembly mounting bolts :
2.0 ~ 2.9 N·m (0.2 ~ 0.3 kgf·m, 1.4 ~ 2.2 lbf·ft)

Page 325 of 1575

CHAPTER 6:
Automatic Transaxle
System

Page 326 of 1575

General Information

Page 327 of 1575

2007 > 2.7L V6 GASOLINE >
SPECIAL TOOLS
TOOL
(Number and name) Illustration
Use
09200 - 38001
Engine support fixture
Removal and installation of transaxle.

Page 328 of 1575

2007 > 2.7L V6 GASOLINE >
SPECIFICATION
Item F4A51
Torque converter type 3 - element, 1 - stage, 2 - phase type
Transaxle type 4 - speed forward, 1 - speed reverse
Engine displacement 2.7L GSL
Gear ratio 1st
2.842
2nd 1.495
3rd 1.000
4th 0.731
Reverse 2.720
Final gear ratio 4.520
Shift pattern Variable
Shift range 4range ( P- R- N- D) + Sports mode
Shift range valve PWM ; 5EA(Duty control) , VFS
Planetary gear 2EA(Output planetary/Overdrive planetary)
Clutch 3EA
Brake 2EA
OWC 1EA
TIGHTENING TORQUE ITEM Nmkgf·m lb- ft
Control cable nut 8 ~ 120.8 ~ 1.2 5.8 ~ 8.6
Input shaft speed sensor 10 ~ 121.0 ~1.2 7 ~ 8
Output shaft speed sensor 10 ~ 121.0 ~1.2 7 ~ 8
Manual control lever 18 ~ 251.8 ~ 2.5 13 ~ 18
Transaxle range switch 10 ~ 121.0 ~1.2 7 ~ 8
Valve body cover 10 ~ 121.0 ~1.2 7 ~ 8
Valve body mounting bolt 10 ~ 121.0 ~1.2 7 ~ 8
Oil temperature sensor 10 ~ 121.0 ~1.2 7 ~ 8
Oil filler plug 29 ~ 342.9 ~ 3.421.4 ~ 25.1
Oil drain plug 40 ~ 504.0 ~ 5.0 29 ~ 36
Solenoid valve support 5 ~ 70.5 ~ 0.7 4 ~ 5
Pressure check plug 8 ~ 100.8 ~ 1.0 6 ~ 7
Transaxle mounting sub bracket nut 60 ~ 806.0 ~ 8.0 43 ~ 58
Transaxle mounting bracket bolts 40 ~ 554.0 ~ 5.5 29 ~ 40
Transaxle mounting insulator bolt 90 ~ 1109.0 ~ 1165 ~ 80
Transaxle and engine mounting bolt 65 ~ 856.5 ~ 8.5 47 ~ 61.5
Drive plate bolt 46 ~ 534.6 ~ 5.333.3 ~ 38.3

Page 329 of 1575

LUBRICANT
ItemSpecified lubricant Quantity
Transmission oil Diamond ATF SP - III8.5ℓ(9.0 Us qt, 7.5Imp.qt)
SEALANT Item Specified Sealant
Rear cover
Torque converter housing
Valve body cover Three Bond - TB 1281B or LOCTITE - FMD - 546
Transmission case side cover Three Bond - TB 1389 or LOCTITE - 518
Side cover Three Bond - TB 1389 or LOCTITE - 518/587

Page 330 of 1575

Automatic Transaxle System

Page:   < prev 1-10 ... 281-290 291-300 301-310 311-320 321-330 331-340 341-350 351-360 361-370 ... 1580 next >