headlamp KIA Optima 2016 4.G User Guide

Page 543 of 623

Maintenance
44
8


NOTICE
If you connect unauthorized elec-
tronic devices to the battery, the bat-
tery may be discharged. Never use
unauthorized devices.
Recharging the battery
Your vehicle has a maintenance-free,
calcium-based battery.
If the battery becomes discharged
in a short time (because, for exam-
ple, the headlamps or interior
lamps were left on while the vehi-
cle was not in use), recharge it by
slow charging (trickle) for 10 hours.
If the battery gradually discharges because of high electric load while
the vehicle is being used, recharge
it at 20-30A for two hours. When recharging the battery,
observe the following precautions:
The battery must be removed from
the vehicle and placed in an area
with good ventilation.
Do not allow cigarettes, sparks, or flame near the battery.
Watch the battery during charging, and stop or reduce the charging
rate if the battery cells begin
gassing (boiling) violently or if the
temperature of the electrolyte of
any cell exceeds 49°C (120°F).
Wear eye protection when check- ing the battery during charging.
Disconnect the battery charger in the following order.
1. Turn off the battery charger main switch.
2. Unhook the negative clamp from the negative battery terminal.
3. Unhook the positive clamp from the positive battery terminal.WARNING- Risk of elec-
trocution
Never touch the electrical igni-
tion system while the vehicle is
running. This system works
with high voltage which can
shock you.
WARNING- Recharging Battery
Never attempt to recharge the
battery when the battery cables
are connected.
JF CAN (ENG) 8.qxp 11/5/2015 6:40 PM Page 44

Page 562 of 623

863
Maintenance
3. Pull the suspected fuse straightout. Use the removal tool provided
on the engine compartment fuse
panel cover.
4. Check the removed fuse; replace it if it is blown.
Spare fuses are provided in theengine compartment fuse panel.
5. Push in a new fuse of the same rating, and make sure it fits tightly
in the clips.
If it fits loosely, consult an authorized
Kia dealer.
If you do not have a spare, use a fuse of the same rating from a circuityou may not need for operating thevehicle, such as the power outletfuse.
If the head lamp, turn signal lamp,
stop signal lamp, fog lamp, DRL, tail
lamp, HMSL do not work and the
fuses are OK, check the fuse panel
in the engine compartment. If a fuse
is blown, it must be replaced.
✽ ✽ NOTICE
If the headlamp, fog lamp, turn sig-
nal lamp, or tail lamp malfunction
even without any problem to the
lamps, have the vehicle checked by
an authorized Kia dealer for assis-
tance.
OJF075023
CAUTION - Fuse Panel
Covers
Set all switches to ON before
driving.
If the vehicle is going to be unused for over 1 month, setall switches to OFF to preventthe batteries from draining.
The contact points of the switches may wear out withexcessive use. Please refrainfrom excessive use of theswitches (except for long-termparking for over 1 month).
JF CAN (ENG) 8.qxp 11/5/2015 6:40 PM Page 63

Page 575 of 623

Maintenance
76
8
LIGHT BULBS
Bulb replacement precaution
Please keep extra bulbs on hand
with appropriate wattage ratings in
case of emergencies.
Refer to “Bulb Wattage” in chapter 9.
When changing lamps, first turn off
the engine at a safe place, firmly
apply the parking brake and detach
the battery’s negative (-) terminal.
Use only bulbs of the specified
wattage.✽ ✽ NOTICE
• If the light bulb or lamp connector
is removed while the lamp is still
on, the fuse box's electronic sys-
tem may log it as a malfunction.
Therefore, a lamp malfunction
incident may be recorded as a
Diagnostic Trouble Code (DTC) in
the fuse box.
• It is normal for an operating lamp to flicker momentarily. This is due
to a stabilization function of the
vehicle’s electronic control device.
If the lamp lights up normally
after momentarily blinking, then
it is functioning as normal.
However, if the lamp continues to
flicker several times or turns off
completely, there may be an error
in the vehicle’s electronic control
device. Please have the vehicle
checked by an authorized Kia
dealer immediately.
WARNING- Working on
the lights
Prior to working on the light,
firmly apply the parking brake,
ensure that the ignition switch
is turned to the LOCK position
and turn off the lights to avoid
sudden movement of the vehi-
cle and burning your fingers or
receiving an electric shock.
CAUTION -Light replace-
ment
Be sure to replace the burned- out bulb with one of the samewattage rating. Otherwise, itmay cause damage to the fuseor electric wiring system.
CAUTION -Headlamp
Lens
To prevent damage, do notclean the headlamp lens withchemical solvents or strongdetergents.
JF CAN (ENG) 8.qxp 11/5/2015 6:40 PM Page 76

Page 576 of 623

877
Maintenance
If you don’t have the necessary tools,
the correct bulbs and the expertise,
consult an authorized Kia dealer. In
many cases, it is difficult to replace
vehicle light bulbs because other
parts of the vehicle must be removed
before you can get to the bulb. This is
especially true if you have to remove
the headlamp assembly to get to the
bulb(s).
Removing/installing the headlamp
assembly can result in damage to
the vehicle.
If non- genuine parts or substandard
bulbs are used, it may lead to blow-
ing a fuse or other wiring damages.
Do not install extra lamps or LEDs to
the vehicle. If additional lights are
installed, it may lead to lamp mal-
functions and flickering. Additionally,
the fuse box and other writing may
be damaged.Light bulb position (Front)
OJFA075134
OJFA075135
■Head lamp - Type A
■Head lamp - Type BOJFA075136
OJFA075137
■Head lamp - Type C
■Head lamp - Type D
(1) Front turn signal lamp
(and position lamp for Type A)
(2) Headlamp (Low)
(3) Headlamp (High) (and DRL for Type A) (4) Headlamp (Low/High)
(5) Day time running lamp
/Position lamp (LED type)
(6) Side marker
JF CAN (ENG) 8.qxp 11/5/2015 6:40 PM Page 77

Page 578 of 623

879
Maintenance
Light bulb position (Side)
(1) Side repeater lamp (LED type)
Headlamp (HID type) bulb
replacement
If the light bulb does not operate,
have the vehicle checked by an
authorized Kia dealer.
✽ ✽NOTICE
HID lamps have superior perform-
ance vs. halogen bulbs. HID lamps
are estimated by the manufacturer to
last twice as long or longer than halo-
gen bulbs depending on their fre-
quency of use. They will probably
require replacement at some point in
the life of the vehicle. Cycling the
headlamps on and off more than typ-
ical use will shorten HID lamps life.
HID lamps do not fail in the same
manner as halogen incandescent
lamps. If a headlamp goes out after a
period of operation but will immedi-
ately relight when the headlamp
switch is cycled it is likely the HID
lamp needs to be replaced. HID
lamping components are more com-
plex than conventional halogen bulbs
thus have higher replacement cost.
OJF075039L
WARNING- HID
Headlamp (if equipped)
Do not attempt to replace or
inspect the HID headlamp
(XENON bulb) due to electric
shock danger. If the light bulb
does not operate, have your
vehicle checked by an author-
ized Kia dealer.
JF CAN (ENG) 8.qxp 11/5/2015 6:41 PM Page 79

Page 579 of 623

Maintenance
80
8
Headlamp (Low beam) bulb
replacement
1. Open the hood.
2. Remove the headlamp bulb cover
by turning it counterclockwise.
3. Remove the bulb-socket from the headlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp
assembly.
4. Remove the bulb from bulb-socket by pulling it out. 5. Insert a new bulb by inserting it
into the bulb-socket.
6. Install the bulb-socket in the head- lamp assembly by aligning the
tabs on the bulb-socket with the
slots in the headlamp assembly.
Push the bulb-socket into the
headlamp assembly and turn the
bulb-socket clockwise.
7. Install the headlamp bulb cover by turning it clockwise.
Headlamp bulb
OJFA075073
WARNING- Halogen
bulbs
Handle halogen bulbs with care.
Halogen bulbs contain pres- surized gas that will produce
flying pieces of glass if bro-
ken.
OHD076046
JF CAN (ENG) 8.qxp 11/5/2015 6:41 PM Page 80

Page 580 of 623

881
Maintenance
Always handle them carefully, andavoid scratches and abrasions. If
the bulbs are lit, avoid contact with
liquids. Never touch the glass with
bare hands. Residual oil may
cause the bulb to overheat and
burst when lit. A bulb should be
operated only when installed in a
headlamp.
If a bulb becomes damaged or cracked, replace it immediately
and carefully dispose of it.
Wear eye protection when chang- ing a bulb. Allow the bulb to cool
down before handling it.Headlamp (High beam) bulb
replacement
1. Open the hood.
2. Remove the headlamp bulb cover by turning it counterclockwise.
3. Disconnect the headlamp bulb socket-connector.
4. Remove the bulb-socket from the headlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp
assembly. 5. Install a new bulb-socket assem-
bly in the headlamp assembly by
aligning the tabs on the bulb-sock-
et with the slots in the headlamp
assembly. Push the bulb-socket
into the headlamp assembly and
turn the bulb-socket clockwise.
6. Install the headlamp bulb cover by turning it clockwise.
OJFA075076
JF CAN (ENG) 8.qxp 11/5/2015 6:41 PM Page 81

Page 581 of 623

Maintenance
82
8
Front turn signal lamp bulb
replacement
1. Open the hood.
2. Remove the bulb-socket from the
headlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp
assembly.
3. Remove the bulb from the bulb- socket by pressing it in and rotat-
ing it counterclockwise until the
tabs on the bulb align with the
slots in the bulb-socket. Pull the
bulb out of the bulb-socket 4. Insert a new bulb by inserting it
into the bulb-socket and rotating it
until it locks into place.
5. Install the socket in the headlamp assembly by aligning the tabs on
the bulb-socket with the slots in
the assembly. Push the bulb-sock-
et into the headlamp assembly
and turn the socket clockwise.
Position lamp + DRL (LED
type) bulb replacement
If the position lamp + DRL (1) does
not operate, have the vehicle
checked by an authorized Kia dealer.
OJFA075079OJFA075150
JF CAN (ENG) 8.qxp 11/5/2015 6:41 PM Page 82

Page 605 of 623

93
Specifications & Consumer information
BULB WATTAGE
Light BulbWattage (W) Bulb type
Front Headlamps (Low)
55W HB3 (9005+)
Headlamps (Low) - HID type 35WD3S
Headlamps (High) 55W HB3 (9005+)
Front turn signal lamps 21W2357NA LL
Front position lamps 0.7WLED
Daytime running light LED type 6.5W LED
Side Repeater lamps Bulb type 5W
W5W LL
LED type0.5WLED
Rear Rear Stop/Tail lamps (outside)
Bulb type5W P21
Rear tail lamps (Inside) 5W W5W
Rear Stop/Tail lamps (outside) LED type12W LED
Rear tail lamps (Inside) 6W LED
Rear turn signal lamps 21W PY21W
Back-up lamps 16W W16W
High mounted stop lamp* 3W LED
License plate lamps 5W W5W
Interior Map lamps
Bulb type 10W FESTON BULB
LED type 1W LED
Room lamps 10W FESTON BULB
Personal lamps 1W LED
Vanity mirror lamps 5W FESTON BULB
Glove box lamp 5W FESTON BULB
Trunk lamp 5W FESTON BULB
JF CAN (ENG) 9.qxp 11/5/2015 4:31 PM Page 3

Page 619 of 623

I7
Index
Key positions ..................................................................6-6Ignition switch position ................................................6-6
Illuminated ignition switch ..........................................6-6
Starting the engine ........................................................6-8
Lane departure warning system (LDWS) ......................6-93 Conditions that cause the LDWS not to operate ........6-95
Conditions that cause missed warnings and false warnings ..........................................................6-96
Warning indicator........................................................6-95
LCD display ..................................................................4-63 LCD Modes ................................................................4-63
Service Mode ..............................................................4-64
User Settings Mode ....................................................4-66
Light bulbs ....................................................................8-76\
Back-up lamp bulb replacement ................................8-86
Bulb replacement precaution ......................................8-76
Front turn signal lamp bulb replacement ....................8-82
Glove box lamp bulb replacement ..............................8-91
Headlamp (HID type) bulb replacement ....................8-79
Headlamp (High beam) bulb replacement ..................8-81
Headlamp (Low beam) bulb replacement ..................8-80
High mounted stop lamp bulb replacement ................8-89 License plate lamp bulb replacement ........................8-88
Light bulb position (Front) ........................................8-77
Light bulb position (Rear) ..........................................8-78
Light bulb position (Side) ..........................................8-79
Map lamp bulb replacement ......................................8-89
Personal lamp bulb replacement ................................8-91
Position lamp + DRL (LED type) bulb replacement..8-82
Rear turn signal lamp bulb replacement ....................8-83
Room lamp bulb replacement ....................................8-90
Side repeater lamp bulb replacement..........................8-83
Stop and tail lamp (LED type) bulb replacement ......8-86
Stop and tail lamp bulb replacement ..........................8-84
Tail lamp bulb replacement ........................................8-87
Trunk lamp bulb replacement ....................................8-92
Vanity mirror lamp bulb replacement ........................8-89
Lighting........................................................................\
4-103 AFLS (Adaptive Front Lighting System) ................4-109
Battery saver function ..............................................4-103
Check headlight ......................................................4-108
Daytime running light ..............................................4-103
Headlight leveling device..........................................4-109
High Beam Assist ....................................................4-106
High beam operation ................................................4-105
Lighting control ........................................................4-103
Turn signals and lane change signals........................4-108
Luggage volume ..............................................................9-5
K
L
JF CAN (ENG) Index.qxp 9/23/2015 4:32 PM Page 7

Page:   < prev 1-10 11-20 21-30 next >