buttons KIA OPTIMA HYBRID 2014 Features and Functions Guide

OPTIMA HYBRID
FEATURES & FUNCTIONS GUIDE
32
*IF EQUIPPED
Automatic Climate Control with Navigation System*
REMINDER: Your Automatic
Climate Control system
may differ from those in the
illustrations. See your Owner’s
Manual for more details.
Climate Control Auto Function:
1. Press AUTO to select Full Auto
Operation
2. Press
MODE buttons to control
which vents air flows through
3. Press DUAL to select Dual
Temperature Control OperationDefrost Outside Windshield:
1. Set Fan Speed to the highest
position

2. Set Te m p e r a t u r e to Hot
3. Press the Front Defrost button
Defog Inside Windshield:
1. Set desired Fan Speed
2. Set desired Temperature
3. Press the Front Defrost button



O


OKeep inside glass
as clean as possible
to reduce window
fogging


ODefrost
Mode
activates A/C and
opens Fresh Air Vent


OMAX A/C Mode
automatically
engages Recirculated
Air


ODuring Auto
Operation, the A/C
indicator will NOT
illuminate. The fan
speed, air intake,
airflow and air
conditioning may
be engaged at any
time to reach desired
temperature and
reduce humidity
QUICK TIPS
Air Flow Modes
To select Air Flow Modes, rotate the Mode Selection button:
Face-Level Bi-Level Floor-Level Floor/Defrost-Level
REAR FRONT
CLIMATE
Fan Speed Control
button
Temperature Control
knob
Rear Windshield
Defroster Front Windshield
Defroster
System OFF buttonMode Selection button
Air Conditioning On/Off
button
Dual Temperature
Control knob
Dual Climate Control
Button
Recirculated Air button
ECON (Economy Air
Conditioning) button
Climate information
screen selection button Automatic Climate
Control button
CENTER PANEL

OPTIMA HYBRID
FEATURES & FUNCTIONS GUIDE
34
*IF EQUIPPED
SEATING
21SET
Driver Position Memory System*To store a seating position into memory, first place the
shifter into P (Park) while the ignition switch is on. Then:
1. Adjust the driver’s seat and outside rearview mirror
2. Press the SET button
A on the control panel. System
will beep once
3. Press one of the memory buttons
B within 5 seconds
after pressing the SET button
A. The system will beep twice when memory has been stored
4. “Driver (1 or 2) set is memorized” will appear on the instrument cluster LCD
Power Adjustable Driver’s Seat*Move/Press controls to adjust Seat forward/backward, Seat Cushion, Seatback and Lumbar
SeatbackB
LumbarC
Seat forward/
backwardA
Seat CushionA
B
C
A


Driver Position Memory
System Video

To view a video on your
mobile device, snap this
QR Code or visit the
listed website.
Refer to page 2 for more
information.
QR CODE
www.KuTechVideos.com/tf23/2014
AB

37
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPERATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED


O


OYou can reprogram a single HomeLink ® button by repeating Step 2


OErasing programmed buttons will delete all trained transmitters
QUICK TIPS
The Auto-Dimming Rearview Mirror is designed to reduce
glare from a vehicle’s headlights visible in the rear and also
connect up to three electronic transmitters in one location.
To turn automatic dimming ON or OFF, press button
F
HomeLink® with Auto-Dimming
Rearview Mirror*
How to Sync Transmitter with HomeLink®*
Erasing programmed buttons:
A HomeLink® button B HomeLink® button C Indicator lightD HomeLink® button

E Glare detection sensor F Automatic dimming ON/OFF G Compass control buttonIf programming for the first time, begin with Step 1
(repeating this step will delete all information).
To program non-rolling and rolling code garage door
openers and other devices:
1. Press and hold the left
A and center

D buttons
simultaneously until the indicator light C begins to
flash (to reprogram buttons, skip this step)
2. Press and hold the desired button
A B D and hold
the button on the transmitter while it is approximately
1 to 3 inches away from the mirror. The HomeLink®
Indicator light

C will flash rapidly once the frequency
signal has been successfully programmed
To finish programming rolling code garage door openers,
complete these steps:
3. Locate the “learn” or “smart ” button on the garage
door’s motor head unit. Press and release the button
and complete Step 4 within 30 seconds
4. Firmly press and release the programmed HomeLink®
button up to three times
Press and hold the left

A and center
D buttons
simultaneously for approximately 20 seconds,
and then release both buttons within 30 seconds.Operating HomeLink®:
Press one of the programmed HomeLink® buttons.
REMINDER: Mirror indicator light
C will illuminate when automatic
dimming is ON.
If your garage door opener was manufactured in 2011 or later, and you’re unable to program your vehicle’s HomeLink
® system, you may need to
purchase a HomeLink
® Repeater Kit. For more information, go to www.HomeLink.com or call (800) 355-3515 .
A
B
C
D
E
F
G
OTHER KEY FEATURES