buttons KIA SEDONA 2016 Features and Functions Guide

24
REMINDER: Using the power outlets (accessory plugs) for prolonged periods of time with the ENGINE START/STOP button in the ACC position (Engine OFF ) could cause the battery to discharge .
For more information on the Aux/USB/iPod® Port, AC Inverter* and Power Outlets, refer to the Owner's Manual.
Aux/USB/iPod® Port, AC
Inverter* and Power Outlets
Clock* USB Port Video To view a video on your mobile device, snap this QR Code or visit the listed website .
Refer to page 2 for more information .
QR CODE
www.KuTechVideos.com/yp13/2016
Standard Audio System* Clock Setup:
Press the H button to advance the time by one hour . Press the M
button to advance the time by one minute .
UVO eServices System* Clock Setup:
Press the CLOCK button to display the Clock setting screen . Then
use the on-screen buttons to navigate through setup .
UVO eServices with Navigation System* Clock Setup:
Press the Setup button . Then press the on-screen Clock icon to
enter clock settings .
USB, iPod® and AUX ports [A] to connect audio
devices and an iPod®
AC Inverter* [B] - 115V/100 watt power
inverters are located in the back of the center
console and in the luggage zone* (See page 9 for
ON/OFF button information)
USB chargers* are located in the center panel
and in the back of the center console
Power outlets are located in the center console,
passeng er console and the luggage zone*
Press the DONE button on the screen to ensure changes are saved .
QUICK TIP
Press and hold both for more than 3 seconds to switch from 12- to 24-hour formats .
QUICK TIP
The power outlets are inactive when the ENGINE START/STOP button is OFF .
QUICK TIP
AB
B
A
(Clock /buttons located on Center Panel)
SEDONA FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
CENTER PANEL

26
Automatic Climate Control
Rear Climate Control
[A] Driver's temperature control knob
[B] AUTO (automatic control) button
[C] Climate information screen selection button
[D] Passenger’s temperature control knob
[E] SYNC temperature control selection button
[F] Front fan speed control button
[G] Air Conditioning Off button
[H] Mode Selection button
[I] Rear fan speed control button
[J] A /C on button
[K ] Air intake control button
[L] Front windshield defroster button
[M Rear window defroster button
[N] Rear control lock button
[O] Rear control on button
[P] Rear temperature control knob
[Q] Rear temperature control buttons
[R] Rear AUTO climate control button
[S] Rear mode selection button
[ T ] Rear air conditioning OFF button
[U] Rear fan speed control buttons
AD
EB
C
P
FGHI
JKLMNO
U
TSR
Q
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
SEDONA FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
CENTER PANEL

27
Automatic Climate Control (Continued)
Climate Control Auto Function
1 . Press AUTO to select Full Auto Operation - The Auto setting
automatically controls the airflow modes, fan speeds, air intake
and air conditioning according to the temperature setting selected
2 . Set desired Temperature
3 . Press SYNC to select Sync Temperature Control Operation which
synchronizes the passenger’s temperature to the driver’s setting
Defrost Outside Windshield:
1 . Set Front Fan Speed to the highest position
2 . Set Temperature to Hot
3 . Press the Front Defrost button [~]
Defog Inside Windshield:
1 . Set Front Fan Speed to desired position
2 . Set desired Temperature
3 . Press the Front Defrost but ton [~]
REMINDERS:
• Pressing any button during AUTO operation will deactivate the AUTO function and switch to manual mode, except for Temperature Control
• When in AUTO mode, Air Flow Mode and Fan Speed do not display on the Climate Control Display
•Warm air may flow in through vents if Recirculated Air button is not pressed ON (LED lit)
• Your Automatic Climate Control system may differ from those in the illustrations . See your Owner’s Manual for more details
Air Flow Modes
To select Air Flow Modes, press the mode buttons to cycle
through to desired mode:
Face-Level
Bi-Level
F lo o r- L evel
Floor/Defrost-Level

•Defrost Mode [~] activates A /C and opens Fresh Air Vent to help dehumidify the air and improve Defroster performance •During Auto Operation, the A /C indicator will NOT illuminate . The fan speed, air intake, air flow and air conditioning may automatically be engaged at any time to reach desired temperature and reduce humidity •Keep inside glass as clean as possible to reduce window fogging
QUICK TIPS
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
CENTER PANEL

28
Defrost Outside Windshield:
1 . Set Fan Speed to the highest position
2 . Set desired Temperature
3 . Press the Defrost button [~]
Defog Inside Windshield:
1 . Set Fan Speed to desired position
2 . Set desired Temperature
3 . Press the Defrost button [~]
Your Manual Climate Control system may differ from those in the illustrations. See your Owner’s Manual for more details.
Air Flow Modes
To select Air Flow Modes, press the Mode
selection buttons:
Face-Level
Bi-Level
F lo o r- L evel
Floor/Defrost-Level
Manual Climate Control*Rear Climate Control*
[A] Front fan speed control knob
[B] Front window defroster button
[C] Rear window defroster button
[D] Air conditioning button
[E] Air intake control button
[F] Front temperature control knob
[G] Front mode selection buttons
[H] Rear fan speed control knob
[I] Rear temperature control knob
[J] Rear control lock button
[K] Rear control on button
[L] Rear air conditioning OFF button
[M Rear fan speed control buttons
[N] Rear mode selection buttons
[O] Rear temperature control buttons
AF
LMO
BC
G
JHI
D
K
E
N
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
SEDONA FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
CENTER PANEL

29
Heated Steering Wheel*
Press Heated Steering Wheel button [A] to turn the Steering
Wheel Heater on/off, while the ENGINE START/STOP button
is in the ON position . Steering Wheel Heater will turn off
automatically in 30 minutes, or when button is pressed
again to deactivate .
(Buttons located below Gear Shift)

•If ignition is turned OFF, then ON again within 30 minutes of Steering Wheel Heater being turned ON, the system will remain in the ON position •System does NOT turn off when ignition is cycled . To turn off system, press the Heated Steering Wheel button
QUICK TIPS
Heated and Ventilated Seats Video To view a video on your mobile device, snap this QR Code or visit the listed website .
Refer to page 2 for more information .
QR CODE
www.KuTechVideos.com/yp13/2016
Seat Warmers / Ventilated Seats*
Seat Warmers
•Press right side of button [B] once for high setting
(3 LEDs lit)
•Press button twice for medium setting (2 LEDs lit)
•Press a third time for low setting (1 LED lit) and
again to turn OFF
Ventilated Seats
•Press left side of button [C] once for high setting
(3 LEDs lit)
•Press twice for medium setting (2 LEDs lit)
•Press a third time for low setting (1 LED lit)
and again to turn OFF

•With the Seat Warmer switch in the ON position, the heating system in the seat turns OFF or ON automatically depending on the seat temperature . •When Seat Warmers or Ventilated Seats button is pressed ON and ignition is cycled, the system will turn ON again .
QUICK TIPS
(Buttons located below Gear Shift)
Warming ( Yellow LED)
Ventilating (Blue LED)
A
A
B
B
C
C
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
CENTER PANEL

30
Front Seat Headrest Adjustment
To raise headrest: Pull headrest up .
To lower headrest: Press lock [A], then press the headrest down .
Driver Position Memory System*
The integrated system stores into memory the position of the
Driver’s Seat and the Outside Rearview Mirrors .
To store positions into memory, first place the Gear Shift into
P (Park) while the ENGINE START/STOP button is in the ON
position . Then:
1 . Adjust the Driver’s Seat and the Outside Mirrors
2 . Press the SET button [B] on the control panel . System will
beep once
3 . Press one of the memory buttons [C] within 5 seconds . The
system will beep twice when memory has been stored
(Buttons located on Driver's Door Panel)
A
B
C
A
B
C
SEDONA FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
SEATING

36
Remote Keyless Entry (Folding Key)*
[A] Press the release button to unfold the key
[B] Press to lock All Doors
[C] Press to unlock Driver’s Door: Press twice in 4 seconds to unlock All Doors and Rear Hatch, and
manually open
[D] Press and hold left /right button to automatically open/close the power sliding doors*
[E] Manual Liftgate*: Press and hold for more than 1 second to unlock Rear Hatch and manually open .
[E] Power Liftgate*: Press and hold for more than 1 second for Power Liftgate to automatically open/close
[F] Press and hold more than a half second for Panic Alarm . To turn OFF Alarm, press any button
Remote button configuration may vary depending on vehicle options.
Double-Turn Lock/Unlock All
•Turn clockwise once to unlock Driver’s Door
•Turn clockwise again within 4 seconds to unlock All Doors
•Turn counterclockwise once to lock All Doors
A
B
C
D
FE
D
Power Sliding Doors*
Press the left /right Power Sliding Door button [G] on the overhead controls
or on the key fob [D] to automatically open/close the sliding doors .
GG
REMINDER: If the POWER DOOR OFF button is depressed, the Smart Liftgate will not operate .
For more information on the Power Sliding Doors operation, please refer to the Owner's Manual.
(Buttons located in overhead controls)
A
B
C
D
D
G
E
E
F
SEDONA FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
OTHER KEY FEATURES

38
How to Sync Transmitter with HomeLink®*
If programming for the first time, begin with Step 1 (repeating this step will
delete all information) .
To program non-rolling and rolling code garage door openers and
other devices:
1 . Press and hold the left [A] and center [D] buttons simultaneously until the
indicator light [C] begins to flash (to reprogram buttons, skip this step)
2 . Press and hold the desired button [A], [B] or [D] and hold the button
on the transmitter while it is approximately 1 to 3 inches away from
the mirror . The HomeLink® Indicator light [C] will flash rapidly once the
frequency signal has been successfully programmed
To finish programming rolling code garage door openers, complete
these steps:
3 . Locate the “learn” or “smart” button on the garage door’s motor
head unit . Press and release the button and complete Step 4 within
30 seconds
4 . Firmly press and release the programmed HomeLink® button up to
three times
Operating HomeLink®:
Press one of the programmed HomeLink® buttons .
Erasing programmed buttons:
Press and hold the left [A] and center [D] buttons simultaneously
for approximately 20 seconds, and then release both buttons within
30 seconds .
If your garage door opener was manufactured in 2011 or later, and you’re unable to program your vehicle’s HomeLink® system, you may need to purchase a HomeLink Repeater Kit. For more information, go to www.HomeLink.com or call (800) 355-3515.
The HomeLink® with Auto-Dimming Rearview Mirror* is designed to reduce
glare from a vehicle’s headlights located in the rear and also connect up to
three electronic transmitters into one location .
• To turn automatic dimming ON, press [~] button [F]
• To turn automatic dimming OFF, press [~] button [G]
REMINDER: Mirror indicator light [C] will illuminate when automatic dimming is ON .
HomeLink® with Auto-Dimming
Rearview Mirror*
[A] HomeLink® button
[B] HomeLink® button
[C] Indicator light
[D] HomeLink® button
[E] Glare detection sensor
[F] Automatic dimming ON
[G] Automatic dimming OFF
•
•You can reprogram a single HomeLink® button by repeating Step 2 •Erasing programmed buttons will delete all trained transmitters
QUICK TIPS
ABCDEFG
A
A
E
B
ABD
C
C
AD
F
F
CG
G
D
D
C
SEDONA FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
OTHER KEY FEATURES

42
Power Liftgate (Tailgate)*
Inside the Vehicle:
Press the Power Liftgate Open/Close button* [A] to
automatically open/close the Liftgate .
Depress the POWER DOOR OFF button* [B] to disable .
REMINDER: If POWER DOOR OFF button is pressed, the Power Liftgate button on the Smart Key will be disabled .
REMINDERS:
•All doors are closed and locked after about 15 seconds
•If the POWER DOOR OFF button is depressed, the Smart Liftgate will not operate
• The Smart Power Liftgate feature will not operate when the doors are recently closed and locked, and the Smart Key is still detected after 15 seconds near the vehicle or within 60 inches of the door handles, a door is not locked or closed or the Smart Key is in the vehicle
For more information on the Smart Power Liftgate operation, please refer to the Owner's Manual.
Outside the Vehicle:
To open Power Liftgate* automatically, press the Rear Hatch
Release button [C] on exterior of the Liftgate .
Automatically close by pressing Power Liftgate Close button* [D] .
Smart Key:
To open the Power Liftgate*, press and
hold the Smart key Liftgate button [E]
until the Liftgate begins opening . Press
again to close .
REMINDER: Pulling the Rear Hatch upward by the handle or pressing the button a second time will interrupt the automatic opening of the Power Liftgate .

Smart Power Liftgate*
When the Smart Key fob is on your person and you are
near the back of the vehicle, within close proximity, the
hazard lights will blink and a chime will sound for about
3 seconds as an alert that the Smart Power Liftgate* is
about to open .
Then the alert system will blink and chime two additional
times before opening the Smart Power Liftgate* .
The Smart Power Liftgate* feature is OFF by default . To enable the Smart Power
Liftgate*, go to User Settings in the LCD Instrument Cluster modes .
During the Smart Power Liftgate alert, the Smart Power Liftgate can be deactivated with the Smart Key by pressing any button on the key fob .
QUICK TIPS
HOLDHOLD
HOLDE
D
C(Button located on inside edge of liftgate)
AB
(Buttons located on overhead console)
Smart Power Liftgate Video To view a video on your mobile device, snap this QR Code or visit the listed website .
Refer to page 2 for more information .
QR CODE
www.KuTechVideos.com/yp13/2016
AE
B
C
D
SEDONA FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
OTHER KEY FEATURES