instrument cluster KIA SEDONA 2016 Features and Functions Guide

15
Turn Signals & Fog Lights*
To o p e r a t e :
•Turn Signals - Move lever Up/Down for Right /Left Turn Signal
•Fog Lights - Push toggle switch to turn Fog Lights ON/OFF
REMINDER: Headlights must be ON for Fog Light operation .
One-Touch Lane Change Signal is activated by moving the Turn Signal
Lever slightly for less than 1 second and then releasing . The lane change
signal will blink 3 times .
To change how many times (3/5/7) the Lane Change Signal blinks, go to
User Settings Mode in the LCD Instrument Cluster modes .
For more information on the User Settings Mode, please refer to your Owner’s Manual.
Windshield Wipers & Washers
To o p e r a t e :
•Move lever Up/Down to change Wiper modes
•Press button [A] to adjust Intermittent Wipe
•Pull lever to spray and wipeM I S T: Single wipe
OFF: Wiper off
I N T: Intermittent Wipe
LO: Slow wipe
HI: Fast wipe
PUSH
FRONT
PULL
FRONT
PUSH
PULL
PUSH
FRONT
PULL
FRONT
PUSH
PULL
A
Rear Wiper & Washer*
To operate:
•Rotate Rear Wiper switch to change Wiper modes
•Push to spray and wipeHI: Fast wipe
LO: Slow wipe
OFF: Wiper off
A
Pressing button up increases Intermittent wipe frequency and wipe speed . Pressing button down decreases frequency of wipes .
QUICK TIP
LO and HI sets wiper speed . No intermittent wipe function on Rear Wipers .
QUICK TIP
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
STEERING WHEEL CONTROLS

19
Smart Cruise Control System (SCC)*
The Smart Cruise Control System (SCC)* allows you to set the vehicle
to maintain a speed so long as it is not limited by traffic . When traffic is
encountered, the vehicle will be slowed to maintain a set distance behind
traffic without depressing the accelerator or brake pedal .
To set/adjust the SCC speed:
•Press the CRUISE button [A] to turn system ON . The CRUISE indicator will
illuminate on the instrument cluster
•Accelerate/decelerate to the desired speed
•Press the SCC button [B] up or down to adjust or set speed
To set the vehicle-to-vehicle distance: Press the SCC button [C] on the
steering wheel . The image on the LCD screen [E] will change when scrolling
through the settings .
To turn system OFF: Press the CANCEL button [D] . The CRUISE indicator
on the instrument cluster will turn OFF and the LCD screen SCC image will
show "SCC canceled" [F] .
REMINDERS:
•Cruise Control button must be ON in order to turn SCC ON/OFF
•SCC is automatically activated by default when ignition is cycled
(Buttons located on right side of Steering Wheel)
Smart Cruise Control Video To view a video on your mobile device, snap this QR Code or visit the listed website .
Refer to page 2 for more information .
QR CODE
www.KuTechVideos.com/yp13/2016
To change the Cruise Control mode from SCC to standard Cruise Control, press and hold button [C] . Repeat to switch modes again ( The SCC system must not be activated to change modes) .
For the SCC System to operate: •When no vehicle is in front, you must be travelling at a minimum speed of 19 mph •When following a vehicle, there is no minimum speed requirement
When following a vehicle, the system will automatically adjust your cruise speed based on the vehicle in front . It will even bring the vehicle to a complete stop if necessary . If the vehicle remains at a standstill for more than 3 seconds, the system will disable .
QUICK TIPS
A
B
C
SCC canceled
EF
D
A
B
C
E
D
F
C
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
STEERING WHEEL CONTROLS

42
Power Liftgate (Tailgate)*
Inside the Vehicle:
Press the Power Liftgate Open/Close button* [A] to
automatically open/close the Liftgate .
Depress the POWER DOOR OFF button* [B] to disable .
REMINDER: If POWER DOOR OFF button is pressed, the Power Liftgate button on the Smart Key will be disabled .
REMINDERS:
•All doors are closed and locked after about 15 seconds
•If the POWER DOOR OFF button is depressed, the Smart Liftgate will not operate
• The Smart Power Liftgate feature will not operate when the doors are recently closed and locked, and the Smart Key is still detected after 15 seconds near the vehicle or within 60 inches of the door handles, a door is not locked or closed or the Smart Key is in the vehicle
For more information on the Smart Power Liftgate operation, please refer to the Owner's Manual.
Outside the Vehicle:
To open Power Liftgate* automatically, press the Rear Hatch
Release button [C] on exterior of the Liftgate .
Automatically close by pressing Power Liftgate Close button* [D] .
Smart Key:
To open the Power Liftgate*, press and
hold the Smart key Liftgate button [E]
until the Liftgate begins opening . Press
again to close .
REMINDER: Pulling the Rear Hatch upward by the handle or pressing the button a second time will interrupt the automatic opening of the Power Liftgate .

Smart Power Liftgate*
When the Smart Key fob is on your person and you are
near the back of the vehicle, within close proximity, the
hazard lights will blink and a chime will sound for about
3 seconds as an alert that the Smart Power Liftgate* is
about to open .
Then the alert system will blink and chime two additional
times before opening the Smart Power Liftgate* .
The Smart Power Liftgate* feature is OFF by default . To enable the Smart Power
Liftgate*, go to User Settings in the LCD Instrument Cluster modes .
During the Smart Power Liftgate alert, the Smart Power Liftgate can be deactivated with the Smart Key by pressing any button on the key fob .
QUICK TIPS
HOLDHOLD
HOLDE
D
C(Button located on inside edge of liftgate)
AB
(Buttons located on overhead console)
Smart Power Liftgate Video To view a video on your mobile device, snap this QR Code or visit the listed website .
Refer to page 2 for more information .
QR CODE
www.KuTechVideos.com/yp13/2016
AE
B
C
D
SEDONA FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
OTHER KEY FEATURES