KIA STONIC 2018 Owners Manual

EMERGENCY STARTING
Connect cables in numerical order and
disconnect in reverse order.
Jump starting
Jump starting can be dangerous if done
incorrectly. Therefore, to avoid harm to yourself or damage to your vehicle or
battery, follow the jump starting pro‐
cedures. If in doubt, we strongly rec‐ ommend that you have a competent
technician or towing service jump start
your vehicle.
CAUTION
Use only a 12-volt jumper system.You can damage a 12-volt startingmotor, ignition system, and otherelectrical parts beyond repair by useof a 24- volt power supply (eithertwo 12-volt batteries in series or a24-volt motor generator set).
WARNING
nBattery
Never attempt to check the electro‐lyte level of the battery as this maycause the battery to rupture or ex‐plode causing serious injury.
WARNING
nBattery
(Continued)
(Continued)
•Keep all flames or sparks awayfrom the battery. The batteryproduces hydrogen gas which mayexplode if exposed to flame orsparks.If these instructions are not fol‐lowed exactly, serious personal in‐jury and damage to the vehiclemay occur! If you are not sure howto follow this procedure, seekqualified assistance. Automobilebatteries contain sulfuric acid. Thisis poisonous and highly corrosive.When jump starting, wear protec‐tive glasses and be careful not toget acid on yourself, your clothingor on the vehicle.
•Do not attempt to jump start thevehicle if the discharged battery isfrozen or if the electrolyte level islow; the battery may rupture orexplode.
•Do not allow the (+) and (-) jumpercables to touch. It may causesparks.
•The battery may rupture or ex‐plode when you jump start with alow or frozen battery.

7-05
7
What to do in an emergency

Jump starting procedure
1. Make sure the booster battery is12-volt and that its negative termi‐ nal is grounded.
2. If the booster battery is in another vehicle, do not allow the vehicles to
come in contact.
3. Turn off all unnecessary electrical loads.
4. Connect the jumper cables in the exact sequence shown in the illus‐
tration. First connect one end of a
jumper cable to the positive termi‐
nal of the discharged battery (1),
then connect the other end to the
positive terminal on the booster
battery (2).
Proceed to connect one end of the other jumper cable to the negative
terminal of the booster battery (3),
then the other end to a solid, sta‐
tionary, metallic point (for example,
the engine lifting bracket) away
from the battery (4). Do not con‐
nect it to or near any part that
moves when the engine is cranked.
Do not allow the jumper cables to
contact anything except the correct
battery terminals or the correct
ground. Do not lean over the bat‐ tery when making connections.CAUTION
nBattery cables
Do not connect the jumper cablefrom the negative terminal of thebooster battery to the negative ter‐minal of the discharged battery. Thiscan cause the discharged battery tooverheat and crack, releasing bat‐tery acid.Make sure to connect one end of thejumper cable to the negative termi‐nal of the booster battery, and theother end to a metallic point, faraway from the battery.
5. Start the engine of the vehicle with the booster battery and let it run
at 2,000 rpm, then start the engine
of the vehicle with the discharged
battery.
If the cause of your battery discharging
is not apparent, have the systemchecked by a professional workshop.Kia recommends to visit an authorized Kia dealer/service partner.
Push-starting
Your manual transaxle-equipped vehi‐
cle should not be push-started because it might damage the emission control
system.
Vehicles equipped with automatic
transaxle cannot be push-started.
Follow the directions in this section for L

IF THE ENGINE OVERHEATS
If your temperature gauge indicates
overheating, you will experience a loss of power, or hear loud pinging or knock‐
ing, the engine is probably too hot. If
this happens, you should: 1. Pull off the road and stop as soon as it is safe to do so.
2. Place the shift lever in P (automatic transaxle) or neutral (manual
transaxle) and set the parking
brake. If the air conditioning is on, turn it off.
3. If engine coolant is running out un‐ der the vehicle or steam is coming
out from the hood, stop the engine.
Do not open the hood until the
coolant has stopped running or the
steaming has stopped. If there is no
visible loss of engine coolant and no
steam, leave the engine running
and check to be sure the engine
cooling fan is operating. If the fan is
not running, turn the engine off.
4. Check to see if the water pump drive belt is missing. If it is not
missing, check to see that it is
tight.
If the drive belt seems to be satis‐
factory, check for coolant leaking
from the radiator, hoses or under
the vehicle. (If the air conditioning had been in use, it is normal for
cold water to be draining from it
when you stop).
WARNING
While the engine is running, keephair, hands and clothing away frommoving parts such as the fan anddrive belts to prevent injury.
5. If the water pump drive belt is bro‐ ken or engine coolant is leaking out,
stop the engine immediately and
call a professional workshop. Kia
recommends to call an authorized
Kia dealer/service partner.
WARNING
Do not remove the radiator capwhen the engine is hot. This can al‐low coolant to blow out of the open‐ing and cause serious burns.
6. If you cannot find the cause of the overheating, wait until the engine
temperature has returned to nor‐
mal. Then, if coolant has been lost,
carefully add coolant to the reser‐
voir to bring the fluid level in the
reservoir up to the halfway mark.
7. Proceed with caution, keeping alert for further signs of overheating. Ifoverheating happens again, call a
professional workshop. Kia recom‐
mends to call an authorized Kia
dealer/service partner.
CAUTION
•Serious loss of coolant indicatesthere is a leak in the cooling sys‐tem. In this case, have the sys‐tem checked by a professionalworkshop. Kia recommends tovisit an authorized Kia dealer/service partner.
•When the engine overheats fromlow engine coolant, suddenlyadding engine coolant may causecracks in the engine. To preventdamage, add engine coolantslowly in small quantities.

7-07
7
What to do in an emergency

TIRE PRESSURE MONITORING SYSTEM (TPMS) (IF EQUIPPED)
0:##
0:#
Low tire pressure telltale (1) / TPMS
SET switch (2)
System Overview
The tire pressure monitoring system (TPMS) senses change in radius of the
tire. If the tire pressure decreases be‐
low the recommended pressure, the system warning light will be illumina‐
ted.
For the system to function properly, it
is the driver’s responsibility to set the system by following accurate proce‐
dure and set current tire pressure.
The warning light will illuminate on the
cluster when one or more of your tires is under-inflated after the TPMS is set.
The warning light will also illuminate to
warn the driver of system malfunction.
Please refer to the above image (1) for
further information.
TPMS Setting
The driver can set the TPMS by follow‐
ing procedures below: 1. Inflate all tires to the recommen‐ ded pressure.
2. Start the engine, make sure the ve‐ hicle is not moving, and press the
TPMS switch (2) left side on the
driver’s seat for over 3 seconds.
3. Check if the (
) warning indicator
blinks for 4 seconds.
4. Check if following message appears on the cluster (if equipped).
❈ If the warning light does not blink
or the message does not pop up,
perform the process again from 2.
For recommended tire pressure of this
vehicle, refer to L

• If the low pressure light is illumina‐ted.
• If the suspension or ABS has been re‐ placed.
CAUTION
If the system is set without adjust‐ing tire pressure, false alarm couldoccur or the telltale will not be dis‐played even though the vehicle issignificantly under-inflated.Make sure all tires are properly ad‐justed to the recommended pressurewhen setting.If the system is not set even in re‐quired situations, false alarm couldoccur or the telltale will not be dis‐played even though the vehicle issignificantly under-inflated.The system will not be set if youpress the SET switch (2) while driv‐ing. Make sure to stop the vehicleand press the switch (2) for over 3seconds.•Be sure the tire is cold before in‐flating the pressure.A cold tire means the vehicle hasbeen sitting for 3 hours or drivenwithin 1.6km (1mile).
Indication of Low Tire Pressure
0:#-
The () warning light will illuminate
when an under-inflated tire is indica‐ ted. In certain types, the above mes‐
sage might be displayed on the cluster.
If the warning light illuminates, reduce
your speed, avoid hard cornering and rapid braking. Have your vehicle inspec‐
ted by a professional workshop. Kia
recommends to visit an authorized Kia dealer/service partner.
Check the pressure of all tires and in‐
flate to the proper pressure according
to procedures, and if required, replace or repair the tires. If you cannot reach a close service sta‐
tion, stop the vehicle at a safe place,
check all tires and operate the TPMS setting procedure. If you are unable to
adjust the tire pressure, use the repair
tools to repair or change to spare tire and contact a professional workshop.
Kia recommends to call an authorized
Kia dealer/service partner.
You may not be able to identify low tire
pressure visually. Use precise tools to measure and adjust tire pressure.
Please note that a tire that is hot due
to prolonged driving, therefore will have high pressure. We recommend you to
measure and adjust the tire pressure
after the vehicle has driven for less than 1.6 km (1 mile) within 3 hours.
CAUTION
•The indicator may remain illumina‐ted after changing to a spare tire,because radius of spare tire is dif‐ferent. Be sure to change to a reg‐ular tire.
(Continued)

7-09
7
What to do in an emergency

(Continued)
•For safe driving, please note thatthe TPMS is not a substitute forproper tire maintenance. It is thedriver’s responsibility to maintaincorrect tire pressure, and all tiresshould be checked monthly tomaintain the recommended pres‐sure.
•The warning light may illuminate ifthe system is not set in requiredsituations.
•In cold weather, the low tire pres‐sure warning light may illuminateeven if the tire was adjusted tothe proper pressure. It does notmean your TPMS is malfunctioningbecause the decreased tempera‐ture leads to a lowering of tirepressure. Check the tires and ad‐just to the recommended pressure.
•System performance may reducein the following situations.-Improper system setting
-Using tires on the market (Origi‐nal tire recommended)
-Driving on snowy, slippery, orunpaved roads
(Continued)
(Continued)
-Hard cornering, rapid accelerat‐ing and braking repeatedly
-Driving too slow or fast
-If the vehicle is overloaded
-If a spare tire or snow chain isinstalled
•When filling tires with more air,conditions to turn off the low tirepressure telltale may not be met.This is because a tire inflator has amargin of error in performance.The low tire pressure telltale willbe turned off if the tire pressure isabove the recommended tire infla‐tion pressure.
WARNING
•Driving with an under-inflated tirecauses the tire to overheat andlead to tire failure. It also reducestire tread life, handling of the vehi‐cle, braking ability, and fuel effi‐ciency, causing instability of thevehicle. In this case, contact pro‐fessional workshop to maintainproper tire pressure. Kia recom‐mends to contact an authorizedKia dealer/service partner.
•Sudden damage to the tire causedby external factors may not be in‐dicated immediately. If the vehicleis unstable, immediately removeyour foot off the accelerator ped‐al, move the vehicle to a safe posi‐tion for inspection.
Tire Pressure Monitoring
System malfunction
The TPMS malfunction indicator will il‐
luminate () after it blinks for approx‐
imately 1 minute when there is a prob‐ lem with the Tire Pressure Monitoring
System. This sequence will continue upon subsequent vehicle start-ups as
long as the malfunction exists.
What to do in an emergency
7-10

If the indicator remains illuminated or
illuminates even after TPMS setting, have the system checked by a profes‐
sional workshop. Kia recommends to
visit an authorized Kia dealer/service partner.
WARNING
•If there is a malfunction with theTPMS, low tire pressure will not beindicated. In this case, have thesystem serviced by a professionalworkshop. Kia recommends to visitan authorized Kia dealer/servicepartner.
•If the system does not work dueto TPMS removal or installation ofrelated parts with different speci‐fication, it might be a problemwhen the vehicle is being regularlyinspected.
•When repairing TPMS relatedparts, be sure to replace them toparts with original specification orthose which satisfy the TPMS reg‐ulation.-TPMS related parts : tire, wheel,ABS unit, suspension
WARNING
nFOR EUROPE
Do not modify the vehicle. It may in‐terfere with the TPMS function.❈ All vehicles sold in the EUROPEmarket during below period must beequipped with TPMS.-New model vehicle : Nov. 1, 2012 ~
-Current model vehicle : Nov. 1,2014~(Based on vehicle registra‐tions)
Reference : Indicator Light
Status
StatusSymbol
Low Pressure
*MMVNJOBUFT
System Malfunc‐ tion
*MMVNJOBUFT
BGUFS
CMJOLJOH

TFDPOET

Setting
5VSOT
PGG
BGUFS
CMJOLJOH


TFDPOET


7-11
7
What to do in an emergency

IF YOU HAVE A FLAT TIRE (WITH SPARE TIRE, IF EQUIPPED)
Jack and tools
0:#%
The jack, jack handle, wheel lug nut
wrench are stored in the luggage com‐ partment.
Pull up the luggage box cover to reach
this equipment. 1. Jack handle
2. Jack
3. Wheel lug nut wrench
Jacking instructions
The jack is provided for emergency tire
changing only.
To prevent the jack from L

Store the tire in the reverse order of
removal.
To prevent the spare tire and tools from L

WARNING
nChanging a tire
•To prevent vehicle movementwhile changing a tire, always setthe parking brake fully, and al‐ways block the wheel diagonallyopposite the wheel beingchanged.
•We recommend that the wheelsof the vehicle be chocked, andthat no person remain in a vehi‐cle that is being jacked.
6. Loosen the wheel lug nuts counter‐clockwise one turn each, but do not remove any nut until the tire has
been raised off the ground.
0:#%
0:#%
7. Place the jack at the front (1) or rear (2) jacking position closest to
the tire you are changing. Place the
jack at the designated locations un‐
der the frame. The jacking posi‐
tions are plates welded to the frame with two tabs and a raised
dot to index with the jack.
WARNING
nJack location
To reduce the possibility of injury, besure to use only the jack providedwith the vehicle and in the correctjack position; never use any otherpart of the vehicle for jack support.
8. Insert the jack handle into the jack and turn it clockwise, raising the
vehicle until the tire just clears the
ground. This measurement is ap‐
proximately 30 mm (1.2 in). Before
What to do in an emergency
7-14