service KIA STONIC 2018 Workshop Manual

Page 257 of 523

• On loose or uneven road surfaces, op‐eration of the anti-lock brake system
may result in a longer stopping dis‐
tance than for vehicles equipped with a conventional brake system.
8
CAUTION
•If the ABS warning light is on andstays on, you may have a problemwith the ABS. In this case, howev‐er, your regular brakes will worknormally.
(Continued)
(Continued)
•The ABS warning light will stay onfor approximately 3 seconds afterthe ignition switch is ON. Duringthat time, the ABS will go throughself-diagnosis and the light will gooff if everything is normal. If thelight stays on, you may have aproblem with your ABS. In thiscase, have the system checked bya professional workshop. Kia rec‐ommends to visit an authorizedKia dealer/service partner.
CAUTION
•When you drive on a road havingpoor traction, such as an icy road,and operate your brakes continu‐ously, the ABS will be active con‐tinuously and the ABS warninglight may illuminate. Pull your carover to a safe place and stop theengine.
(Continued)
(Continued)
•Restart the engine. If the ABSwarning light is off, then your ABSsystem is normal. Otherwise, youmay have a problem with the ABS.In this case, have the systemchecked by a professional work‐shop. Kia recommends to visit anauthorized Kia dealer/service part‐ner.
NOTICE
When you jump start your vehicle
because of a drained battery, the
engine may not run as smoothly and
the ABS warning light may turn on
at the same time. This happens be‐
cause of the low battery voltage. It
does not mean your ABS is malfunc‐
tioning.
•Do not pump your brakes!
•Have the battery recharged before
driving the vehicle.

6-35
6
Driving your vehicle

Page 262 of 523

The VSM does not operate when:
• Driving on bank road such as gradient or incline
• Driving rearward
• ESC OFF indicator light (
) remains
on the instrument cluster
• EPS indicator light remains on the in‐ strument cluster
VSM operation off
If you press the ESC OFF button to turn
off the ESC, the VSM will also cancel and the ESC OFF indicator light (
) il‐
luminates.
To turn on the VSM, press the button again. The ESC OFF indicator light goes
out.
Malfunction indicator
The VSM can be deactivated even if you
don’t cancel the VSM operation by pressing the ESC OFF button. It indi‐
cates that a malfunction has been de‐
tected somewhere in the Electric Pow‐ er Steering system or VSM system.
If the ESC indicator light (
) or EPS
warning light remains on, have the sys‐ tem checked by a professional work‐
shop. Kia recommends to visit an au‐
thorized Kia dealer/service partner.
NOTICE
•The VSM is designed to function
above approximately 15 km/h (9
mph) on curves.
•The VSM is designed to function
above approximately 30 km/h (18
mph) when a vehicle is braking on
a split-mu road. The split-mu road
is made of surfaces which have
different friction forces.
WARNING
•The Vehicle Stability Managementsystem is not a substitute for safedriving practices but a supplemen‐tary function only. It is the respon‐sibility of the driver to alwayscheck the speed and the distanceto the vehicle ahead. Always holdthe steering wheel firmly whiledriving.
(Continued)
(Continued)
•Your vehicle is designed to activateaccording to the driver’s intention,even with installed VSM. Alwaysfollow all the normal precautionsfor driving at safe speeds for theconditions – including driving in‐clement weather and on a slipperyroad.
•Driving with varying tire or wheelsizes may cause the VSM systemto malfunction. When replacingtires, make sure they are thesame size as your original tires.
ESS : Emergency Stop Signal (if
equipped)
The Emergency Stop Signal system
alerts the driver behind by blinking the stop light when the vehicle suddenly
stops or when the ABS activates in a
stop. (The system activates when the vehicle speed is over 55km/h and the
vehicle deceleration is over 7m/s² or the
ABS activates when the vehicle emer‐ gency braking.)
When the vehicle speed is under 40
km/h and the ABS deactivates or the
sudden stop situation is over, the stop light blinking will stop.
Driving your vehicle
6-40

Page 263 of 523

CAUTION
The Emergency Stop Signal systemwill not work if the hazard warningflasher is already on.
Good braking practices
WARNING
•Whenever leaving vehicle or park‐ing, always set the parking brakeas far as possible and fully engagethe vehicle's transaxle into thepark position. Vehicles not fully en‐gaged in park with the parkingbrake set are at risk for moving in‐advertently and injuring yourselfor others.
•All vehicles should always have theparking brake fully engaged whenparking to avoid inadvertentmovement of the car which can in‐jure occupants or pedestrians.
• After parking the vehicle, check to besure the parking brake is not engaged
and that the parking brake indicator light is out before driving away. • Driving through water may get the
brakes wet. They can also get wet
when the car is washed. Wet brakes
can be dangerous! Your car will not
stop as quickly if the brakes are wet. Wet brakes may cause the car to pull
to one side.
To dry the brakes, apply the brakes
lightly until the braking action returns
to normal, taking care to keep the car
under control at all times. If the brak‐ ing action does not return to normal,
stop as soon as it is safe to do so and
have your vehicle inspected by a pro‐
fessional workshop.
Kia recommends to call an authorized Kia dealer/service partner.
• Don't coast down hills with the car out of gear. This is extremely hazard‐
ous. Keep the car in gear at all times,
use the brakes to slow down, then
shift to a lower gear so that engine braking will help you maintain a safe
speed.
• Don't "ride" the brake pedal. Resting your foot on the brake pedal while
driving can be dangerous because it
can result in the brakes overheating and losing their effectiveness. It also
increases the wear of the brake com‐
ponents. • If a tire goes flat while you are driv‐
ing, apply the brakes gently and keepthe car pointed straight ahead while
you slow down. When you are moving
slowly enough for it to be safe to do
so, pull off the road and stop in a
safe place.
• If your car is equipped with an auto‐ matic transaxle, don't let your car
creep forward. To avoid creeping for‐
ward, keep your foot firmly on the
brake pedal when the car is stopped.
• Be cautious when parking on a hill. Firmly engage the parking brake andplace the shift lever in P (Park). If
your car is facing downhill, turn the
front wheels into the curb to help
keep the car from rolling. If your car is facing uphill, turn the front wheels
away from the curb to help keep the
car from rolling. If there is no curb or
if it is required by other conditions to
keep the car from rolling, block the wheels.

6-41
6
Driving your vehicle

Page 274 of 523

• Press the speed limit switch once
again.
• Press the cruise switch (If you press cruise switch, the cruise system will
turn on)
If you press the O switch once, the set speed limit will cancel, but it will not
turn the system off. If you wish to re‐
set the speed limit, move the lever up (to RES+) or down (to SET-) to the de‐
sired speed.CAUTION
The "OFF" indicator will blink if thereis a problem with speed limit controlsystem.If this occurs, have the systemchecked by a professional workshop.Kia recommends to visit an author‐ized Kia dealer/service partner.
Driving your vehicle
6-52

Page 275 of 523

FORWARD COLLISION-AVOIDANCE ASSIST (FCA) SYSTEM (IF EQUIPPED)
The FCA system is to reduce or to avoid
accident risk. It recognizes the distance
from the vehicle ahead or the pedes‐ trian through the sensors (i.e. radar
and camera), and, if necessary, warns
the driver of accident risk with the warning message or the warning
alarms.
WARNING
Take the following precautions whenusing the Forward Collision-Avoid‐ance Assist (FCA) System:•This system is only a supplemen‐tal system and it is not intendedto, nor does it replace the need forextreme care and attention of thedriver. The sensing range and ob‐jects detectable by the sensors arelimited. Pay attention to the roadconditions at all times.
•NEVER drive too fast in accordancewith the road conditions or whilecornering.
(Continued)
(Continued)
•Always drive cautiously to preventunexpected and sudden situationsfrom occurring. FCA does not stopthe vehicle completely and doesnot avoid collisions.
System setting and activation
System setting
The driver can activate the FCA by plac‐
ing the ignition switch to the ON posi‐
tion and by selecting 'User Settings', 'Driving Assist', and 'Forward Collision-
Avoidance Assist (FCA)'. The FCA deac‐
tivates, when the driver cancels the system setting.
The warning light illuminates on the LCD display, when youcancel the FCA system.
The driver can monitor the FCAON/OFF status on the LCD display.
When the warning light remains ON
with the FCA activated, have the sys‐tem checked by a professional work‐
shop. Kia recommends to visit an au‐
thorized Kia dealer/service partner. The driver can select the initial warning
activation time in the User Settings and Driving Assist in the instrument cluster
LCD display. The options for the initial
Forward Collision Warning include the following:
• EARLY - When this condition is se‐
lected, the initial Forward
Collision Warning is activa‐ted earlier than normal.This setting maximizesthe amount of distance
between the vehicle or
pedestrian ahead beforethe initial warning occurs.
• NORMAL - When this condition is se‐
lected, the initial Forward
Collision Warning is activa‐ted normally. This settingallows for a nominalamount of distance be‐
tween the vehicle or pe‐
destrian ahead before theinitial warning occurs.
• LATE - When this condition is se‐ lected, the initial Forward
Collision Warning is activa‐ted later than normal.
This setting reduces theamount of distance be‐

6-53
6
Driving your vehicle

Page 279 of 523

NOTICE
•Do not install any accessories,
such as license plate molding or
sticker, on the sensor area. Nor ar‐
bitrarily replace the bumper.
Those may adversely affect the
sensing performance.
•Always keep the sensor/bumper
area clean.
•Use only soft clothes to wash the
vehicle. Also, do not spray highly-
pressurized water on the sensor
installed on the bumper.
•Be careful not to apply unnecessa‐
ry force on the frontal sensor
area. When the sensor moves out
of the correct position due to ex‐
ternal force, the system may not
normally operate even without the
warning light or message. In this
case, have the vehicle inspected by
a professional workshop. Kia rec‐
ommends to visit an authorized
Kia dealer/service partner.
(Continued)
(Continued)
•Use only the genuine Kia sensor
cover. Do not arbitrarily apply
paint on the sensor cover.
System malfunction
0:#-
• When the FCA is not working proper‐ly, the FCA warning light () will illu‐
minate and the warning message will
appear for a few seconds.
After the message disappears, the
master warning light (
) will illumi‐
nate. In this case, have the vehicle in‐
spected by a professional workshop.
Kia recommends to visit an author‐
ized Kia dealer/service partner. • The FCA warning message may ap‐
pear along with the illumination of
the ESC warning light.
WARNING
•The FCA is only a supplementalsystem for the driver’s conven‐ience. The driver should hold theresponsibility to control the vehicleoperation. Do not solely depend onthe FCA system. Rather, maintaina safe braking distance, and, ifnecessary, depress the brake ped‐al to lower the driving speed.
•The FCA may unnecessarily pro‐duce the warning message and thewarning alarms. Also, due to thesensing limitation, the FCA maynot produce the warning messageand the warning alarm at all.
•When there is a malfunction withthe FCA, the braking control doesnot operate upon detecting a colli‐sion risk even with other brakingsystems normally operating.
(Continued)

6-57
6
Driving your vehicle

Page 282 of 523

-When the stopped vehicle in front
gets out of the lane, it may not be
recognized by your FCA. Always pay great attention.
- Recognizing the vehicle
When the vehicle in front has heavy
loading extended rearward, or when
the vehicle in front has higher ground clearance, it may induce a hazardous
situation.
Recognizing pedestrians
- The pedestrian is not fully captured
by the camera sensor, or the pedes‐
trian does not walk in the upright po‐ sition.
- The pedestrian moves very fast.
- The pedestrian abruptly appears in
front.
- The pedestrian wears clothes in the
color similar to the background.
- The outside is too bright or too dark.
- The vehicle drives at night or in the
darkness.
- There is an item similar to a person’s
body structure.
- The pedestrian is small.
- The pedestrian has impaired mobility.
- It is difficult to distinguish the pedes‐
trian from the surroundings.
- The sensor recognition is limited. -
There is a group of pedestrians.
WARNING
•Cancel the FCA in the User Set‐tings on the LCD display, beforetowing another vehicle. While tow‐ing, the brake application may ad‐versely affect your vehicle safety.
•Pay great caution to the vehicle infront, when it has heavy loadingextended rearward, or when it hashigher ground clearance.
•The sensor only detects pedes‐trian, not carts, bicycles, motorcy‐cles, luggage bags, or strollers.
•The FCA does not operate in a cer‐tain situation. Thus, never test-operate the FCA against a personor an object. It may cause a severeinjury or even death.
•When reinstalling the windshield orLane Departure Warning (LDW)camera after replacement or re‐moval, have the vehicle inspectedby a professional workshop. Kiarecommends to visit an authorizedKia dealer/service partner.
Driving your vehicle

6-60

Page 286 of 523

2. Auditory warningIf you leave the lane, the warning
sound operates for maximum
3 seconds.
The color of symbol will change de‐
pend on the condition of Lane De‐
parture Warning (LDW) System
system.
• White
color: When you activate the lane
departure warning system
by pressing the Lane Depar‐
ture Warning (LDW) System
button, system operating
conditions are not satisfiedor the sensor does not de‐tect the lane line.
• Green
color: When you activate the lane
departure warning system
by pressing the Lane Depar‐
ture Warning (LDW) System
button, system operating
conditions are satisfied andthe sensor detect the laneline.
• Yellow
color: When there is a malfunction
with the lane departurewarning system.Warning indicator
0:#-
When the Lane Departure Warning
(LDW) System is not working properly, the warning light will illuminate and the
warning message will come on for a
few second. After the message disap‐ pears, the master warning light will illu‐
minate.
In this case, have the system checked
by a professional workshop.
Kia recommends to visit an authorized Kia dealer/service partner.
The Lane Departure Warning
(LDW) System does not operate
when:
• The driver turns on the turn signal or the hazard warning flasher to change
lane.
• Driving on the lane line.
NOTICE
To change lanes, operate the turn
signal switch, then change the lane.
The Lane Departure Warning
(LDW) System may not warn
you even if the vehicle leaves
the lane, or may warn you even
if the vehicle does not leave the
lane when:
• The lane is not visible due to snow, rain, stain, a puddle or many other
things.
• The brightness of the outside changes suddenly.
• The headlights are off at night or in a tunnel.
Driving your vehicle
6-64

Page 290 of 523

System malfunction
0:#-
When the "Check Driver Attention
Warning (DAW) system" warning mes‐ sage appears, the system is not work‐
ing properly. In this case, have the vehi‐
cle inspected by a professional work‐ shop. Kia recommends to visit an au‐
thorized Kia dealer/service partner.
WARNING
•The Driver Attention Warning sys‐tem is not a substitute for safedriving practices, but a conven‐ience function only. It is the re‐sponsibility of the driver to alwaysdrive cautiously to prevent unex‐pected and sudden situations fromoccurring. Pay attention to theroad conditions at all times.
•The system may suggest a breakaccording to the driver's drivingpattern or habits even if the driverdoesn't feel fatigue.
•The driver, who feels fatigued,should take a break, even thoughthere is no break suggestion bythe Driver Attention Warning sys‐tem.
NOTICE
The Driver Attention Warning sys‐
tem utilizes the camera sensor on
the front windshield for its opera‐
tion. To keep the camera sensor in
(Continued)
(Continued)
the best condition, you should ob‐
serve the followings:
•NEVER install any accessories or
stickers on the front windshield,
nor tint the front windshield.
•NEVER locate any reflective ob‐
jects (i.e. white paper, mirror) over
the dashboard. Any light reflection
may cause a malfunction of the
Driver Attention Warning (DAW)
system.
•Pay extreme caution to keep the
camera sensor out of water.
•NEVER arbitrarily disassemble the
camera assembly, nor apply any
impact on the camera assembly.
CAUTION
The Driver Attention Warning sys‐tem may not properly operate withlimited alerting in the following sit‐uations:
(Continued)
Driving your vehicle
6-68

Page 295 of 523

After the foreign substance is removed,
if you drive for approximately 10 minutes, the system will work nor‐
mally.
If the system does not work normally
even though the foreign substance is removed, take your vehicle to a profes‐
sional workshop and have the system
checked. Kia recommends to visit an authorized Kia dealer/service partner.
It is possible to get the message with
no foreign substance on the rear
bumper, for example, when driving in sparse rural or open area, such as des‐
ert, where there is insufficient data for
operation.
This message may also activate during heavy rain or due to road spray.
In this case, the vehicle does not need
service.
If the system does not work properly, a
warning message
(L

Page:   < prev 1-10 ... 11-20 21-30 31-40 41-50 51-60 61-70 71-80 81-90 91-100 ... 130 next >