stop start KIA STONIC 2018 Owners Manual

Operation in foreign countries
If you are going to drive your vehicle in
another country, be sure to: • Observe all regulations regarding reg‐ istration and insurance.
• Determine that acceptable fuel is available.
Diesel engine
Diesel fuel
Diesel engine must be operated only on
commercially available diesel fuel that
complies with EN 590 or comparable standard. (EN stands for "European
Norm"). Do not use marine diesel fuel,
heating oils, or non-approved fuel addi‐ tives, as this will increase wear and
cause damage to the engine and fuel
system. The use of non-approved fuels and / or fuel additives will result in a
limitation of your warranty rights.
Diesel fuel of above cetane 51 is used in
your vehicle. If two types of diesel fuel
are available, use summer or winter fuel properly according to the following
temperature conditions. • Above -5°C (23°F) ... Summer type diesel fuel.
• Below -5°C (23°F) ... Winter type die‐ sel fuel. Watch the fuel level in the tank very
carefully : If the engine stops through
fuel failure, the circuits must be com‐
pletely purged to restart.
CAUTION
Do not let any gasoline or water en‐ter the tank. This would make it nec‐essary to drain it out and to bleedthe lines to avoid jamming the injec‐tion pump and damaging the engine.
CAUTION
nDiesel Fuel (if equipped withDPF)
It is recommended to use the regula‐ted automotive diesel fuel for dieselvehicle equipped with the DPF sys‐tem.If you use diesel fuel including highsulfur (more than 50 ppm sulfur)and unspecified additives, it cancause the DPF system to be dam‐aged and white smoke can be emit‐ted.
Biodiesel
Commercially supplied Diesel blends of
no more than 7% biodiesel, commonly
known as "B7 Diesel" may be used in your vehicle if Biodiesel meets EN
14214 or equivalent specifications. (EN
stands for "European Norm"). The use of biofuels exceeding 7% made from
rapeseed methyl ester (RME), fatty
acid methyl ester (FAME), vegetable oil methyl ester (VME) etc. or mixing die‐
sel exceeding 7% with biodiesel will
cause increased wear or damage to the engine and fuel system. Repair or re‐
placement of worn or damaged compo‐
nents due to the use of non approved fuels will not be covered by the manu‐
factures warranty.
CAUTION
•Never use any fuel, whether dieselor B7 biodiesel or otherwise, thatfails to meet the latest petroleumindustry specification.
•Never use any fuel additives ortreatments that are not recom‐mended or approved by the vehiclemanufacturer.

1-05
1
Introduction

INSTRUMENT PANEL OVERVIEW
0:#
1. Instrument cluster.......................... .......................... p. 4-45
2. Horn...................................... ...................................... p. 4-39
3. Driver’s front air bag........................ ........................ p. 3-46
4. Light control............................... ............................... p. 4-81Turn signals................................ ................................ p. 4-84
5. Wiper/Washer.............................. .............................. p. 4-90
6. Ignition switch.............................. .............................. p. 6-06 ENGINE START/STOP button................. ................. p. 6-10
7. Hazard warning flasher switch............... ............... p. 7-02
8. Audio
9. Central door lock switch..................... ..................... p. 4-18
10. Climate control system............... ............... p. 4-99, 4-108
11. AUX-USB port.............................. .............................. p. 5-03
12. Shift lever............................ ............................ p. 6-20, 6-24
13. Parking brake lever.................................................... p. 6-31
14. Passenger’s front air bag.................... .................... p. 3-46
15. Power outlet.............................. .............................. p. 4-129
16. Glove box................................. ................................. p. 4-122
17. Steering wheel audio remote control
18. Cigarette lighter........................... ........................... p. 4-126
19. Seat warmer.............................. .............................. p. 4-128
20. Heated steering wheel switch................ ................ p. 4-39
21. Idle Stop and Go system OFF button.......... .......... p. 6-16
22. USB charger.............................................................. p. 4-130

2-05
2
Your vehicle at a glance

(Continued)
key) is dangerous even if the key isnot in the ignition switch or startbutton is ACC or ON position.Children copy adults and they couldplace the key in the ignition switchor press the start button. The igni‐tion key (smart key) would enablechildren to operate power windowsor other controls, or even make thevehicle move, which could result inserious bodily injury or even death.Never leave the keys in your vehiclewith unsupervised children, whenthe engine is running.
WARNING
Kia recommends to use parts for re‐placement from an authorized Kiadealer/service partner. If an after‐market key is used, the ignitionswitch may not return to ON afterSTART. If this happens, the starterwill continue to operate causingdamage to the starter motor andpossible fire due to excessive currentin the wiring.
Immobilizer system
Your vehicle may be equipped with an
electronic engine immobilizer system to
reduce the risk of unauthorized vehicle
use.
Your immobilizer system is comprised of a small transponder in the ignition
key and electronic devices inside the
vehicle.
Vehicles without smart key system
With the immobilizer system, whenever
you insert your ignition key into the ig‐ nition switch and turn it to ON, it checks
and determines and verifies if the igni‐
tion key is valid or not.If the key is valid, the engine will start.
If the key is invalid, the engine will not
start.
To deactivate the immobilizer system:
Insert the ignition key into the key cyl‐ inder and turn it to the ON position.
To activate the immobilizer system:
Turn the ignition key to the OFF posi‐
tion. The immobilizer system activates
automatically. Without a valid ignition key for your vehicle, the engine will not
start.
Vehicles with smart key system
Whenever the engine start/stop button
is changed to the ON position, the im‐
mobilizer system checks and verifies if the key is valid or not. If the key is valid, the engine will start.
If the key is invalid, the engine will not
start.
To deactivate the immobilizer system
Change the engine start/stop button to
the ON position.
To activate the immobilizer system
Change the engine start/stop button to the OFF position. The immobilizer sys‐
tem activates automatically. Without a
valid smart key for your vehicle, the engine will not start.
WARNING
In order to prevent theft of your ve‐hicle, do not leave spare keys any‐where in your vehicle. Your immobil‐izer password is a customer uniquepassword and should be kept confi‐dential. Do not leave this numberanywhere in your vehicle.

4-05
4
Features of your vehicle

NOTICE
When starting the engine, do not
use the key with other immobilizer
keys around. Otherwise the engine
may not start or may stop soon af‐
ter it starts. Keep each key separate
in order to avoid a starting malfunc‐
tion.
CAUTION
Do not put metal accessories nearthe ignition switch. Metal accesso‐ries may interrupt the transpondersignal and may prevent the enginefrom being started.
NOTICE
If you need additional keys or lose
your keys, Kia recommends to visit
an authorized Kia dealer/service
partner.
CAUTION
The transponder in your ignition keyis an important part of the immobil‐izer system. It is designed to giveyears of trouble-free service, how‐ever you should avoid exposure tomoisture, static electricity and roughhandling. Immobilizer system mal‐function could occur.
CAUTION
Do not change, alter or adjust theimmobilizer system because it couldcause the immobilizer system tomalfunction. In this case, have thesystem serviced by a professionalworkshop. Kia recommends to visitan authorized Kia dealer/servicepartner.Malfunctions caused by improper al‐terations, adjustments or modifica‐tions to the immobilizer system arenot covered by your vehicle manu‐facturer warranty.
Features of your vehicle
4-06

SMART KEY (IF EQUIPPED)
09.
With a smart key, you can lock or un‐
lock a door (and tailgate) and even start the engine without inserting the
key.
The functions of buttons on a smart
key are similar to the folding key.
Smart key functions
Carrying the smart key, you may lock
and unlock the vehicle doors (and tail‐ gate). Also, you may start the engine.
Refer to the following, for more details.
Locking
Pressing the button of the front out‐
side door handles with all doors (and tailgate) closed and any door unlocked,
locks all the doors (and tailgate). If all
doors (and tailgate) and engine hood are closed, the hazard warning lights
will blink once to indicate that all doors
(and tailgate) are locked. The button will only operate when the
smart key is within 0.7~1 m (28~40 in.)
from the outside door handle. If you
want to make sure that a door has locked or not, you should check the
door lock button inside the vehicle or
pull the outside door handle.
Even though you press the outside door
handle buttons, the doors will not lock and the chime will sound for 3 seconds
if any of following occur: • The smart key is in the vehicle.
• The ENGINE START/STOP button is in the ACC or ON position.
• Any door except the tailgate is open.
Unlocking
Pressing the button of the front out‐
side door handles with all doors (and tailgate) closed and locked, unlocks all
the doors (and tailgate). The hazard
warning lights blink twice to indicate that all doors (and tailgate) are un‐
locked.
The button will only operate when the
smart key is within 0.7~1 m (28~40 in.) from the outside door handle.
Features of your vehicle
4-10

• Lock the doors by pressing thelock button on the smart key.
After completion of the steps
above, the hazard warning lights
will operate once to indicate thatthe system is armed.
If any door (and tailgate) or en‐
gine hood remains open, the haz‐
ard warning lights won't operate
and theft-alarm will not arm. Af‐
ter this, if all doors (and tailgate)
and engine hood are closed, thehazard warning lights blink once.
Using the transmitter
Park the vehicle and stop the engine.
Arm the system as described below. 1. Turn off the engine and remove the ignition key from the ignition
switch.
2. Make sure that all doors (and tail‐ gate), the engine hood are closed
and latched. 3. Lock the doors by pressing the lock
button on the transmitter.
After completion of the steps
above, the hazard warning lights
will blink once to indicate that the
system is armed.
If any door (and tailgate) or engine
hood remains open, the hazard
warning lights won't operate and
theft-alarm will not arm. After this,if all doors (and tailgate) and engine
hood are closed, the hazard warn‐
ing lights blink once.
•
Do not arm the system until all pas‐sengers have left the vehicle. If thesystem is armed while a passenger(s)remains in the vehicle, the alarm maybe activated when the remaining pas‐senger(s) leave the vehicle. If anydoor, tailgate or engine hood isopened within 30 seconds after en‐tering the armed stage, the systemis disarmed to prevent unnecessaryalarm.
Theft-alarm stage
The alarm will be activated if any of the
following occurs while the system is armed. • A door is opened without using the transmitter (or smart key). • The tailgate is opened without using
the transmitter (or smart key).
• The engine hood is opened.
The horn will sound and the hazard
warning lights will blink continuously for approximately 30 seconds. To turn
off the system, unlock the doors with
the transmitter (or smart key).
Disarmed stage
The system will be disarmed when:
Transmitter
- The door unlock button is pressed.
- The engine is started.
- The ignition switch is in the L

This gauge indicates the temperature
of the engine coolant when the ignition switch or Engine Start/Stop button is
ON.
CAUTION
If the gauge pointer moves beyondthe normal range area toward theL

Shift to P (for smart key system
and automatic transaxle)
• This warning message illuminates ifyou try to turn off the engine with‐
out the shift lever in P (Park) position.
• At this time, the Engine Start/Stop Button turns to the ACC position (If
you press the Engine Start/Stop But‐
ton once more, it will turn to the ON position).
Low Key Battery (for smart key
system)
• This warning message illuminates if the battery of the smart key is dis‐
charged when the Engine Start/Stop Button changes to the OFF position.
Press START button while turning
wheel (for smart key system)
• This warning message illuminates if
the steering wheel does not unlock
normally when the Engine Start/Stop Button is pressed.
• It means that you should press the Engine Start/Stop Button while turn‐
ing the steering wheel right and left.
Steering wheel unlocked (for smart
key system)
• This warning message illuminates if the steering wheel does not lockwhen the Engine Start/Stop Button
changes to the OFF position.
Check Steering Wheel Lock System
(for smart key system)
• This warning message illuminates if the steering wheel does not lock nor‐
mally when the Engine Start/Stop Button changes to the OFF position.
Press brake pedal to start engine
(for smart key system and
automatic transaxle)
• This warning message illuminates if the Engine Start/Stop Button
changes to the ACC position twice by pressing the button repeatedly with‐
out depressing the brake pedal.
• It means that you should depress the brake pedal to start the engine.
Press clutch pedal to start engine
(for smart key system and manual
transaxle)
• This warning message illuminates if the Engine Start/Stop Button
changes to the ACC position twice by
pressing the button repeatedly with‐ out depressing the clutch pedal.
• It means that you should depress the clutch pedal to start the engine.
Key not in vehicle (for smart key
system)
• This warning message illuminates ifthe smart key is not in the vehicle
when you press the Engine Start/ Stop Button.
• It means that you should always have the smart key with you.
Key not detected (for smart key
system)
• This warning message illuminates if
the smart key is not detected when
you press the Engine Start/Stop But‐ ton.
Features of your vehicle
4-62

Press START button again (for
smart key system)
• This warning message illuminates ifyou can not operate the EngineStart/Stop Button when there is a
problem with the Engine Start/Stop
Button system.
• It means that you could start the en‐ gine by pressing the Engine Start/
Stop Button once more.
• If the warning illuminates each time you press the Engine Start/Stop But‐
ton, have the vehicle inspected by a
professional workshop. Kia recom‐
mends to visit an authorized Kia deal‐
er/service partner.
Press START button with key (for
smart key system)
• This warning message illuminates if you press the Engine Start/Stop But‐
ton while the warning message L

WARNING AND INDICATOR LIGHTS
Warning lights
NOTICE
nWarning lights
Make sure that all warning lights are
OFF after starting the engine. If any
light is still ON, this indicates a situa‐
tion that needs attention.
Air bag Warning Light
This warning light illumi‐nates:
• Once you set the ignition switch or Engine Start/Stop Button
to the ON position. - It illuminates for approximately 6 seconds and then goes off.
• When there is a malfunction with the SRS.
In this case, have the vehicle inspec‐
ted by a professional workshop. Kia
recommends to visit an authorized
Kia dealer/service partner.
Seat Belt Warning Light
This warning light informs the driver that the seat belt
is not fastened.
❈ For more details, refer to the L