engine KIA TELLURIDE 2022 Features and Functions Guide

†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED28TELLURIDE FEATURES & FUNCTIONS GUIDE
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Electronic Stability Control Video
QR CODE
REMINDERS:
•
ESC is active by default at vehicle star tup . When ignition is cycled, ESC will turn ON again
•
The ESC indicator light in the instrument cluster will be lit momentarily whenever ESC is active
REMINDERS:
•
HAC does not operate when the gear shift is in P (Park) or N (Neutral) position
•
HAC does not replace the need to apply brakes while the vehicle is stopped on an incline
•
In the event of HAC system malfunction, see an Authorized Kia Dealer for ser vice
•When HAC is active (e .g ., during initial acceleration from a stop on an incline), you may notice that the brakes will momentarily remain engaged after you depress the accelerator
•HAC provides a t wo-second delay before the vehicle may star t rolling backwards
QUICK TIPS
Electronic Stability Control (ESC)†6 /
Traction Control System (TCS)†6
Electronic Stability Control (ESC) is designed to help stabilize the vehicle during certain cornering maneuvers . The Traction Control System (TCS) can help improve traction . It is a good idea to keep both ESC and TCS turned on for daily driving whenever possible .
Press the ESC button B to turn the Traction Control System OFF/ON .
To turn both Electronic Stability Control and the Traction Control System OFF, press and hold the ESC button for more than 3 seconds . Press again to turn ON .
Instrument Cluster Control (Instrument Panel Dimmer)
With the Engine Start/Stop button on or the parking lights/headlights on, press A (+) or (-) to adjust the brightness of the instrument panel illumination .
(But ton located on driver ’s panel, left of the steering wheel)
See section 4 in the Owner’s Manual for more information .
See section 5 in the Owner’s Manual for more information .
See section 5 in the Owner’s Manual for more information .
Hill-Start Assist Control (HAC)†6
Hill-Start Assist Control (HAC) is designed to prevent the vehicle from rolling backwards when accelerating from a stop while on a steep incline .
HAC automatically activates whether ESC is OFF or ON but does NOT activate when ESC has malfunctioned .
AB
DRIVER’S PANEL
DRIVER’S PANEL

ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED29
DRIVER’S PANEL
DRIVER’S PANEL
REMINDER: When the but tons are not pressed, the Reverse Parking Aid Function will not operate and the outside rear view mirrors will not rotate downward .See section 4 in the Owner’s Manual for more information .
For illustrative purposes only . Your actual display, buttons and/or features may vary .
Reverse Parking Aid Function†4
When the gear shift lever is moved into R (Reverse) and the vehicle is moving backwards, the outside rearview mirrors will rotate downward to aid in reverse parking .
To turn Reverse Parking Aid Function ON, move switch A to either the right or to the left . To turn OFF, move switch to the center position .
The outside rearview mirrors will automatically return to their original positions when:
•The Engine Start/Stop button is in the OFF position
•The gear shift lever is moved out of R (Reverse)
•
The outside rearview mirror switch is in the center position
R
L
A
REMINDERS:
•The Engine Star t/Stop but ton needs to be on
•The Gear Shift needs to be in (P) Park
See section 4 in the Owner’s Manual for more information .
For illustrative purposes only . Your actual display, buttons and/or features may vary .(But ton located on driver ’s panel, left of the steering wheel)
Power Liftgate Open/Close Button*
Press and hold the Power Liftgate Open/Close button B to open or close the Liftgate automatically .
B
Manual Folding Mirrors*
To fold the mirrors in manually, pull the mirror towards the window .
Refer to section 4 in the Owner’s Manual for more information .
For illustrative purposes only . Your actual display, buttons and/or features may vary .
If needed, pull the mirror firmly until it folds .
QUICK TIP

DRIVER’S PANEL
DRIVER’S PANEL
REMINDER: When activated or but ton is pressed, the rear passenger windows will not operate from the rear controls .
See section 4 in the Owner’s Manual for more information .
Press C to lock the rear passenger doors . An indicator will illuminate G showing the system is active .
This system is enabled by default, and then activated once the button C is pressed . To deactivate, press the button again .
Electronic Child Safety Lock System
•To use electrical accessories
–ACC position
–When in the OFF position and without depressing the brake pedal, press the ENGINE START/STOP but ton once
–ON position
–When already in the ACC position and without depressing the brake pedal, press the ENGINE START/STOP but ton again
•When in the OFF position and without depressing the brake pedal, press the ENGINE START/STOP but ton t wice
•Keeping the vehicle in the ACC or ON position for extended periods of time without turning the engine on may discharge the vehicle’s bat ter y opening
QUICK TIPS
REMINDERS:
•
If the Smar t Key fob bat ter y is dead, you can still star t the engine by pressing the ENGINE START/STOP but ton with the Lock-but ton end of the Smar t Key . The Smar t Key must contact the ENGINE START/STOP but ton directly, at a right angle
•
In an emergency situation while the vehicle is in motion, you are able to turn the engine off and to the ACC position by pressing the ENGINE START/STOP but ton for more than 2 seconds or 3 times successively within 3 seconds
Engine Start/Stop Button†7
To start the engine:
1 . Depress the brake pedal
2 .
Press the ENGINE START/STOP button while the gear shift is in P (Park) or N (Neutral)
To turn the engine OFF, press the ENGINE START/STOP button while the gear shift is in P (Park) .
To use the ENGINE START/STOP button, you must have the Smart Key on your person or
inside the vehicle .
ENGINE
START
STOP
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Engine Start/Stop Button Video
QR CODE
See section 5 in the Owner’s Manual for more information .
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED31
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Electronic Child Safety Lock System Video
QR CODE

AUTO Light – When the light switch is in the AUTO Light position, the tail lights and headlights will turn ON/OFF automatically depending on the amount of light outside the vehicle .
Daytime Running Lights (DRL) – DRL may help others to see the front of your vehicle during the day . The lights will turn on automatically when the ignition or Engine Start/Stop button is ON and the headlight switch is in the AUTO position, unless one of the following occurs:
• Headlights are on
• Parking brake is applied
• Engine is turned off
• Switch is in the DRL OFF position
Headlight / High Beam Lever Operation
•Rotate lever switch to change the headlight function:
•
Press lever away from you to turn high beam headlights ON
•
Pull lever to flash headlights/high beams or to turn off the high beams
High Beam Assist (HBA)* – High Beam Assist is designed to automatically adjust the headlight range by switching between high and low beams based on light detected from other vehicles and road conditions .
To enable HBA , toggle the light switch to the AUTO Light position and turn on the high beams by pushing the lever away from you . The High Beam Assist indicator will illuminate .
*IF EQUIPPED32TELLURIDE FEATURES & FUNCTIONS GUIDE
REMINDERS:
•
High Beam Assist does not operate below cer tain speeds, or in some lighting and driving conditions . Please be aware of your surroundings and exercise proper road etiquet te when operating a vehicle using the high beams
•HBA will operate when vehicle speed exceeds 25 mph
•
If the lever is pushed away from you while HBA is operational, HBA will turn off and the high beams will be on continuously . If the lever is pulled toward you while HBA is operational, HBA will turn off
•If the light switch is switched to the headlight position, HBA will turn off and low beams will be on continuously
•
When the HBA indicator illuminates on the instrument cluster, the HBA is not working properly . See an authorized Kia dealer for ser vice
OFF
OFF
)FBEMJHIU
QPTJUJPO
1BSLJOH
-JHIU
\
QPTJUJPO
AUTOAuto Light /DRL/ High Beam Assist*
OFFOFF position
Headlights & High Beams
See section 4 in the Owner’s Manual for more information .
A
To operate Turn Signals: Move lever up/down for right/left turn signal .
One-touch lane change signal is activated by briefly pressing the turn signal lever slightly for less than 1 second and then releasing . The lane change signal will blink 3 times .
To change how many times the lane change signal blinks (3/5/7), go to User Settings in the LCD instrument cluster modes .
To operate Fog Lights: Press switch A up/down to turn on/off the Fog Lights .
Turn Signals & Fog Lights*
REMINDER: Headlights must be on for fog light operation .
See section 4 in the Owner’s Manual for more information . For illustrative purposes only . Your actual display, buttons and/or features may vary .
STEERING WHEEL CONTROLS
STEERING WHEEL
CONTROLS

See section 4 in the Owner’s Manual for more information .
STEERING WHEEL
CONTROLS
STEERING WHEEL CONTROLS
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . *IF EQUIPPED33
Headlight position
Parking Light position
AUTOAuto Light /DRL/ High Beam Assist*
OFFOFF position
To operate front wipers & washers:
•Move lever up/down to change wiper modes
MIST: Single wipe LO: Slow wipeOFF: Wiper off HI: Fast wipeINT*/AUTO*: Intermittent*/Auto Rain Sensing*
•Pull to spray and wipe
To operate rear wipers & washers:
•Rotate Rear Wiper switch to change Wiper modes
•Push lever to spray and wipe
Auto Rain Sensing (Auto Control)*
The rain sensor located on the upper end of the windshield glass is designed to sense the amount of rainfall and control the wiping cycle for the proper interval . The more it rains, the faster the wiper operates . When the rain stops, the wiper stops .
To turn ON the auto rain sensing wipers, move lever up/down to AUTO . To adjust the auto rain sensing wiper speed setting, move the speed control switch A up/down .
Auto Rear Wiper* – The feature can be enabled in the User Settings on the Instrument Cluster . When the lever is in the AUTO position, the gear shift is moved into Reverse (R), Auto Rear Wiper activates and will wipe the rear windshield .
Front & Rear Windshield Wipers & Washers
HI
LO
OFF
"
#
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Wipers and Wiper Stalk Video
QR CODE
CImage for illustrative purposes only . See section 7 in the Owner’s Manual for more information .
To lift the windshield wipers to clean the windshield, inspect or replace wiper blades or raise the wipers in snow/ice conditions without damaging the hood, the blades need to be moved to the middle of the windshield (service position) C .
With the ignition ON, turn the ignition OFF, and within 20 seconds move the wiper switch up to the MIST position B and hold the switch for more than two seconds until the wiper blade is in the fully up position .
To return wipers to the normal position, turn the ignition ON, then activate MIST .
Lifting Wipers/Winter Mode (Wiper Service Mode)
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Wiper Service ModeVideo
QR CODE
MIST: Single wipe
OFF: Wiper off
LO: Slow wipe
HI: Fast wipe
INT*/AUTO: Intermittent*/Auto/Rain Sensing*
•When the Engine Star t/Stop but ton is in the ON position and the wiper switch is in AUTO mode, the wiper will automatically operate once to per form a self-check of the system
•Set the wiper to the OFF position when the wiper is not in use
•Moving lever to HI increases intermit tent wipe frequency and wipe speed . Moving lever to LO decreases frequency of wipes
•Pressing but ton A up increases Intermit tent wipe frequency and wipe speed . Pressing but ton A down decreases frequency of wipes
•On Rear Wipers, intermit tent wipe function is not adjustable
QUICK TIPS

STEERING WHEEL CONTROLS
STEERING WHEEL
CONTROLS
(GT steering wheel illustration shown)
Do not adjust the steering wheel while driving as this may cause you to lose control of the vehicle .
See section 4 in the Owner’s Manual for more information .
A
•It may be helpful to pull/push the bot tom of the Steering Wheel towards/away from you to adjust to the desired distance .
QUICK TIP
To adjust the Steering Wheel, push the lock-release lever A down and adjust to the desired angle B and distance C .
When finished, pull the lock-release lever A up to lock Steering Wheel in place .
Tilt/Telescoping Steering Wheel† 19
C
B
See section 4 in the Owner’s Manual for more information .
REMINDER: If the steering wheel becomes too warm, turn the system off . The heated steering wheel may cause burns even at low temperatures, especially if used for long periods of time .
While the Engine Start/Stop button is in the ON position, press D to turn the steering wheel heater ON . The button indicator will illuminate .
The steering wheel heater will turn off automatically in 30 minutes, or when the button is pressed again to deactivate .
MAP RADIO
N AVMEDIASEEK< <TRACK>SETUP
AUTOOFFREARACSYNC
L
72FAUTO72FH
IPASSENGER
AIRBAGOFF
Heated Steering Wheel*
D
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED34TELLURIDE FEATURES & FUNCTIONS GUIDE

AUDIO SYSTEMS
*IF EQUIPPED40TELLURIDE FEATURES & FUNCTIONS GUIDE
AUDIOSYSTEMS
Kia Access with UVO link App Download
Kia Access with UVO link App Features Guide
Go to an app marketplace to download the new Kia Access with UVO link App . Once you download, make sure you register your vehicle and start an account (refer to UVO link Activation page) . Get to know
your new Kia and the available convenient features on the app .
The Kia Access with UVO link App Features Guide is a step-by-step guide helping you utilize the app to its full potential by detailing how to set up and use each feature and adjust various settings . Below are some of the topics included:
•Remote Commands
•Set Climate
•Schedule Service
Download the Kia Access with UVO link App by clicking this dynamic QR code . Some phone’s operating systems may need to be updated to scan dynamic QR codes .
Kia Access with UVO link App Features Guide. Click this dynamic QR code to access the guide . Some phone’s operating systems may need to be updated to scan dynamic QR codes .
2020 SOULMILEAGE722 mi.
355 miEst. RangeDOOR LOCKSREMOTE STARTFind My Car
Kia App Screen for illustrative purposes only . Actual App screen and functionality may vary .
UVO link is currently unavailable for model year 2022 vehicles sold or purchased in Massachusetts . See UVO Terms of Service at owners .kia .com for more information .
For further UVO link operations, refer to the Car Infotainment System Quick Reference Guide .
UVO link is currently unavailable for model year 2022 vehicles sold or purchased in Massachusetts . See UVO Terms of Service at owners .kia .com for more information .
QR CODES
•
To download map updates for the navigation system, go to update .kia .com . Check for updates that are generally available t wice a year
•The smar tphone and vehicle need to be connected to a cellular net work with good wireless signal strength in order to use UVO . If these conditions are not met, remote command may not execute or takes a long time . It will also effect voice commands
•
To use Remote Star t or Remote Star t with Climate Control feature, all doors, hood and trunk/liftgate must be closed and locked
•
When Remote Star t is activated, if the driver does not enter the vehicle within 10 minutes, the Remote Star t will turn the engine off
•When using Remote Star t with Climate Control, turn on for at least a few minutes before get ting into the vehicle, allowing the vehicle interior to reach your desired temperature
•
The quickest way to obtain accurate vehicle status through the app is by pressing the refresh but ton on the app or refreshing the web page when using the customer web por tal
•
In order to preser ve the vehicle bat ter y, UVO will not turn on seven days after the last ignition was on . You will need to restar t the vehicle with a key fob in order to use UVO again
QUICK TIPS

AUDIO SYSTEMS
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
UVO link with Navigation Video
QR CODE
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED41
AUDIO SYSTEMS
•Volume level bet ween different audio modes:
-When switching bet ween audio modes (AM, FM, Bluetooth® Audio, etc .), the audio system saves the previous volume level you were listening to . For example, if you were listening to FM radio at volume level 20 then switched to Bluetooth® Audio and adjusted the volume level to 30, the volume level will be at 20 when you switch back to FM radio
-When using Bluetooth® Audio, the overall volume is dependent on your device’s volume . If the volume is turned down low on your device it will remain low even if the system volume is turned up
•To download map updates for the navigation system, go to update .kia .com . Check for updates that are generally available t wice a year
•The system can register or pair multiple Bluetooth® devices
•Prolonged use of the navigation system in ACC mode may drain the vehicle’s bat ter y . A warning screen may appear periodically to remind users that the navigation system should be operated with the engine running to prevent bat ter y discharge
•When using the voice command feature, wait for the system BEEP before speaking the command
•Surround Sound can be turned on or off
•At any time, you can interrupt UVO link System Command Feedback by pressing the TALK but ton on the steering wheel
QUICK TIPS
Your vehicle’s audio system may differ from that in the illustration . For further UVO link operations, refer to the Car Infotainment System Quick Reference Guide . For other audio system information, refer to pages 35-40 .
To help reduce driver distraction, some audio system functionalities have been modified while the vehicle is in Drive, Reverse or moved out of Park .
UVO link is currently unavailable for model year 2022 vehicles sold or purchased in Massachusetts . See UVO Terms of Service at owners .kia .com for more information .
UVO link with Navigation†1 ,1 0 – FM/AM/SiriusXM®†3/Media (USB, Bluetooth® Audio)
Sound Settings – To adjust the sound settings:
1 . Press the SETUP key on the audio head unit . Select the onscreen SOUND button2 . Select the menu item (Position, Volume, Tone, Priority, Navigation, Advanced, Reset)3 . Use the onscreen buttons to adjust settings
Radio Presets – You can listen to FM, AM and SiriusXM® radio and save frequently used stations . How to Save a Preset – Press and hold the desired slot or star button . This saves the current station in the selected slot
SiriusXM® Smart Favorites – For the first ten favorite SiriusXM® channels, you may play live or repeat from the beginning of a song or a program segment . In Radio mode, choose SiriusXM®, then select any of the first ten favorites . During song or program play, tap the Skip Backward icon to start from the beginning of the song or program . Tap the Play Live icon to return to the live broadcast .
Custom Key H
"
QSPHSBNNBCMF
LFZ
UP
QSPWJEF
RVJDL
BDDFTT
UP
POF
PG
TFWFSBM
BWBJMBCMF
TZTUFN
GFBUVSFT 
5P
1SPHSBN
UIF
$VTUPN
,FZ
1SFTT
BOE
IPME
UIF
$VTUPN
LFZ
4FMFDU
POF
PG
UIF
BWBJMBCMF
GFBUVSFT
ZPV
XPVME
MJLF
UIF
$VTUPN
LFZ
UP
PQFO
MAP RADIO
N AV MEDIASEEK<
<TRACK>SETUPL
MAP RADIO
N AV MEDIASEEK<
<TRACK>SETUPL1SFTT
UP
TFMFDU
'.".4JSJVT9.8j
NPEFT

1SFTT
UP
1PXFS0/0''

3PUBUF
UP
BEKVTU
7PMVNF
1SFTT
UP
HP
UP
$VTUPN
4FU

.FOV
1SFTT
UP
EJTQMBZ
UIF\


."1
TDSFFO
GPS
UIF
DVSSFOU
QPTJUJPO
NPEF
1SFTT
UP
EJTQMBZ
UIF\

/"7
TDSFFO
UP
TFU
EFTUJOB\
UJPO
BOE
SPVUF\

1SFTT
CSJF7UZ
UP
EP
UIF
GPMMPXJOH
·

'.".
NPEF
1MBZ
UIF\

QSFWJPVT
OFYU
GSFRVFODZ·
4JSJVT9.
NPEF
$IBOHF
U\
IF
DIBOOFM
·

.&%*"
NPEF
$IBOHF
U\
IF
USBDL

7TMF
\
PS
UJUMF
1SFTT
BOE
IPME
UP
UIF
EP
UIF\

GPMMPXJOH
PWFS

TFDPOET
·

'.".
NPEF
.PWF
RVJDLMZ
UI\
SPVHI
BMM
PG
UIF
GSFRVFODJ\
FT
8IFO
SFMFBTF\
E

UIF
TZTUFN\

TFFLT
UIF
OFYU
B\
WBJMBCMF
GSFRV\
FODZ·

.&%*"
NPEF
3FXJOET
PS
GBTU
GPSXBSET
UIF
USBDL
PS
7TMF
\
FYDFQU
GPS
#MVFUPPUI8j
"VEJP

1SFTT
UP
EJTQMBZ
4&5\
614FUUJOHT
NPEF

1SFTT
UP
TFMFDU
.&%*"
NPEF
3PUBUF
UP
DIBOHF
3BEJP4JSJVT9.8j
4UBUJPO.FEJB

USBDLT7TMFT

CENTER PANEL
CENTER PANEL
*IF EQUIPPED42TELLURIDE FEATURES & FUNCTIONS GUIDE
Press the SETUP key on the audio head unit, then press the GENER AL button then date/time button to enter the clock settings . Then use the onscreen buttons to navigate through setup and return to exit .
REMINDERS:
•
Daylight Saving must be enabled or disabled in the Clock Set tings screen
•To access manual date and time set ting, turn GPS Time OFF in the Clock Set tings (UVO link with Navigation*)
Refer to the Car Infotainment System Quick Reference Guide for more information .
Clock
The AC Inverter supplies 115V/100W electrical power to operate accessories or equipment . Press the AC Inverter button to activate .
AC Inverter*
(Located behind center console)
See section 4 in the Owner’s Manual for more information .
•The power outlets are inactive when the ignition is in the OFF position
•The Multimedia USB data por t is located next to the Power Outlets A
•USB Charger does not suppor t data transfer
QUICK TIPS
REMINDERS:
•
Using the power outlets (accessor y plugs) for prolonged periods of time with the Engine Star t/Stop but ton in the ACC position (Engine OFF) may cause the bat ter y to discharge
•Only use manufacturer cables that came with your device as third par t y cables may cause damage to the device
•The Multimedia USB Por t B in the center panel charges more slowly than the USB Chargers C throughout the vehicle
Power Outlets A : Use the power outlets for mobile phones and other devices designed to operate on a 12V (180W max) power outlet .
Multimedia USB Port B : Use the USB port to connect USB audio devices and smartphone devices .
USB Charger Ports C : Devices can be recharged using a USB cable . The Engine Start/Stop button needs to be in the ACC/ON/START position to operate the USB Charger .
12V180WUSB
(Located in center panel in front of gearshift)
Multimedia USB Ports, Power Outlets & USB Charger Ports
CBA
See section 4 in the Owner’s Manual for more information .

SHIFT
LOCK
RELEASE
P•R•N•D•
+
•-
SHIFT
LOCK
RELEASE
P•
R•
N•
D•
+
•
-
CENTER PANEL
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . *IF EQUIPPED45
B
•
The instrument cluster and the light beside the shift lever identifies the gear the vehicle is currently in
•Press brake pedal and depress release but ton to move gear shift from N to P, N to R or from P to any gear
•Manual mode downshifts are made automatically when the vehicle slows down . When the vehicle stops, 1st gear is automatically selected
QUICK TIPSREMINDERS:
•
When in P (Park), if the Release but ton is not pressed while shifting, the transmission does not shift
•
If going through a car wash, remind the at tendant to keep the vehicle in Neutral (N) and keep the engine running . Also, disable the power liftgate lid control, turn off the auto rain sensing wipers and fold in the mirrors
CENTER PANEL
See section 5 in the Owner’s Manual for more information .
To shift into any gear from Park, depress the brake pedal, then press the Release button A, located on the side of the gear shift lever, and shift .
P: Park – To shift into Park from any gear, press the Release button B on the gear shift while the vehicle is stationary and the brake pedal is depressed, and shift .
R: Reverse – To shift into Reverse, depress the brake pedal, press the Release button A, and move the shift lever into Reverse .
N: Neutral
D: Drive
[+]: Manual Mode Upshift
[–] : Manual Mode Downshift
Manual Mode: To enter the Manual mode, move the shift lever from D to the left gate B .
To shift while in Manual mode, move the shift lever up [+] to upshift or down [–] to downshift B .
Automatic Transmission and Manual Mode
A